Search NASA⌕ Search

SEARCH · Search NASA

Results for “electron backscattered diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Enhanced electrical and noise properties of nanocomposite vanadium oxide thin films by reactive pulsed-dc magnetron sputtering

Thin films of VO{sub x} (1.3 {<=} x {<=} 2) were deposited by reactive pulsed-dc magnetron sputtering of a vanadium metal target while RF-biasing the substrate. Rutherford back scattering, glancing angle x-ray, and cross-sectional transmission electron microscopy measurements revealed the formation of nanocolumns with nanotwins within VO{sub x} samples. The resistivity of nanotwinned VO{sub x} films ranged from 4 m{Omega}{center_dot}cm to 0.6 {Omega}{center_dot}cm and corresponding temperature coefficient of resistance between -0.1% and -2.6% per K, respectively. The 1/f electrical noise was analyzed in these VO{sub x} samples using the Hooge-Vandamme relation. These VO{sub x} films are comparable or surpass commercial VO{sub x} films deposited by ion beam sputtering.

36 MATERIALS SCIENCE↗

Molecular beam epitaxy growth and optoelectronic properties of droplet-free lattice-matched GaInAsSbBi on GaSb with wavelength extension exceeding 5 μ m

GaInAsSbBi alloys are grown lattice-matched on GaSb by molecular beam epitaxy demonstrating smooth surface morphologies, >5 μm wavelength photoluminescence emission, and minority carrier lifetimes >1 μs. At a growth temperature of 400 °C, the Ga flux is systematically increased and the Bi flux systematically decreased to identify GaInAsSbBi growth conditions that yield smooth droplet-free surface morphologies. The minority carrier lifetime is evaluated using time-resolved photoluminescence, where it is observed that GaInAsSbBi samples exhibit minority carrier lifetimes comparable to their Bi-free GaInAsSb counterparts, on the order of 1.5–2 μs. The bandgap and Urbach energy are evaluated from steady-state photoluminescence to gain insight into the impact of the incorporated Bi. Coupled with Rutherford backscattering spectrometry measurements of the Bi mole fraction, bandgap reduction rates of 97 meV/% Bi in InAsSbBi and 150 meV/% Bi in GaInAsSbBi are observed, significantly higher than previous evaluations in InAsSbBi (35–55 meV/% Bi). Detailed comparisons of the Bi mole fraction, bandgap energy, and Urbach energy indicate that the bandgap reduction potential in this alloy system is inhibited by the formation of Bi clusters; however, the inclusion of Ga in the quinary alloy is effective in suppressing Bi's tendency to incorporate in clusters for Ga mole fractions >9%, maximizing the bandgap reduction per unit Bi and overall optoelectronic quality.

Atomic force microscopy↗

Characterization of Thin Films and Coatings

Just as the numbers and types of thin films have grown dramatically, the needs and approaches for their characterization have also expanded significantly. Adequate characterization of a film or coating depends on the process to create the coating as well as the planned or potential application(s) and expected lifetime. Characterization of a coating or film necessarily requires application of methods that determine properties of the coating and not primarily the substrate. This places some focus on methods that determine properties of layers and not "bulk" material. However, the increasing importance of micro- and nano-structures in coatings and films places an increased importance in methods with high spatial resolution. The growing use of organic films and coatings and the importance of molecular functionalization of inorganic surfaces increase the importance for different types of molecular characterization tools. In most circumstances appropriate characterization requires use of a combination of tools. The purpose of this chapter is to provide an introduction to the basic methods and overview applications for some of the most important tools for characterization of films, coatings and surfaces. The chapter will be organized in six sections: • Technique Overview – This section provides a high level summary of the types of information that can be obtained by different methods and includes information about their sensitivity and resolution. • Incident Photon Methods – Techniques involving incident photons are described and some brief examples of application are shown. Methods included are: x-ray photoelectron spectroscopy (XPS), x-ray diffraction (XRD), x-ray reflectivity (XRR), Fourier transform infra-red spectroscopy (FTIR), laser Raman spectroscopy, ellipsometry, and photoluminescence spectroscopy. • Incident Ion Methods - Methods initiated by ion irradiation are summarized including: Rutherford backscattering spectrometry (RBS), nuclear reaction analysis (NRA), ion channeling, elastic recoil detection analysis (ERDA), secondary ion mass spectrometry (SIMS), glow discharge mass spectrometry and uses of focused ion beams (FIB) (often in combination with scanning electron microscopy). • Incident Electron Methods – Methods involving incident electrons include: Auger electron spectroscopy (AES), scanning electron microscopy (SEM), energy dispersive x-ray analysis (EDS), transmission electron microscopy (TEM), and electron diffraction (low energy electron diffraction [LEED] and reflection high energy electron diffraction [RHEED]). • Other Methods – Additional methods described include scanning probe microscopy (SPM) (including scanning tunneling microscopy [STM] and atomic force microscopy [AFM]) and atom probe microscopy.

36 MATERIALS SCIENCE↗

Structural and magnetic properties of irradiated SiC

We present a comprehensive structural characterization of ferromagnetic SiC single crystals induced by Ne ion irradiation. The ferromagnetism has been confirmed by electron spin resonance, and possible transition metal impurities can be excluded to be the origin of the observed ferromagnetism. Using X-ray diffraction and Rutherford backscattering/channeling spectroscopy, we estimate the damage to the crystallinity of SiC, which mutually influences the ferromagnetism in SiC.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structure, sintering behavior, and microwave dielectric properties of (1 − x) CaWO{sub 4}–xYLiF{sub 4} (0.02 ≤ x ≤ 0.10) ceramics

Highlights: • Structure, sinterability, and dielectric properties of CaWO{sub 4}–YLiF{sub 4} were studied. • CaWO{sub 4} can be densified (TD 97%) at 750 °C/2 h by YLiF{sub 4} doping. • Excellent microwave dielectric properties could be obtained. - Abstract: Structures and sintering behaviors of (1 − x) CaWO{sub 4}–xYLiF{sub 4} (0.02 ≤ x ≤ 0.10) ceramic have been investigated by X-ray powder diffraction (XRD), dilatometry, scanning electron microscopy (SEM) in this work. The microwave dielectric properties were measured with a network analyzer at the frequency of about 8–15 GHz. Limited solid solution could be formed within the compositional range of x < 0.1. The sintering temperature of CaWO{sub 4} could successfully be reduced to ∼750 °C/2 h by doping with small amount of YLiF{sub 4}. An optimized microwave dielectric properties with ϵ{sub r} = 10.5, Q × f = 73 000 GHz and τ{sub f} = −37.7 ppm/°C could be obtained after sintered at the 750 °C for 2 h for x = 0.04 compositions. XRD and back scattering SEM analysis indicated that the (1 − x) CaWO{sub 4}–xYLiF{sub 4} (x = 0.04) ceramic could be chemically compatible with Ag after sintering at 750 °C/2 h.

36 MATERIALS SCIENCE↗

The influence of substrate temperature and Al mobility on the microstructural evolution of magnetron sputtered ternary Ti-Al-N thin films

Ternary Ti-Al-N films were deposited onto Al{sub 2}O{sub 3} (0001) substrates by reactive cosputtering from elemental Ti and Al targets and analyzed by in situ and ex situ x-ray scattering, Rutherford backscattering spectroscopy, transmission electron microscopy, and x-ray photoemission spectroscopy. The deposition parameters were set to values that yield Ti:Al:N ratios of 2:1:1 and 4:1:3 at room temperature. 2TiAlN depositions at 675 deg. C result in epitaxial Ti{sub 2}AlN growth with basal planes parallel to the substrate surface. Nominal 4TiAl3N depositions at 675 deg. C and above, however, yield domain growth of TiN and Ti{sub 2}AlN due to Al loss to the vacuum. Depositions at a lower temperature of 600 deg. C yield films with correct 4:1:3 stoichiometry, but Ti{sub 4}AlN{sub 3} formation is prevented, supposedly by insufficient adatom mobility. Instead, an incoherent Ti{sub n+1}AlN{sub n} structure with random twinned stacking sequences n is obtained that exhibits both basal plane orientations parallel and nearly perpendicular to the substrate interface. X-ray photoemission spectroscopy shows that in contrast to stoichiometric nitrides the Al is metallically bonded and hence acts as twinning plane within the Ti{sub n+1}AlN{sub n} stackings. Domains with perpendicular basal plane orientation overgrow those with parallel orientation in a competitive growth mode. The resulting morphology is a combination of smooth-surface parallel-basal-plane-oriented domains interrupted by repeated facetted hillocklike features with perpendicular basal plane orientation.

36 MATERIALS SCIENCE↗

Synthesis of magnesiowüstite nanocrystallites embedded in an amorphous silicate matrix via low energy multiple ion implantations

The synthesis process is presented for experimentally simulating modifications in cosmic dust grains using sequential ion implantations or irradiations followed by thermal annealing. Cosmic silicate dust analogues were prepared via implantation of 20–80 keV Fe - , Mg - , and O - ions into commercially available p-type silicon (100)wafers. The as-implanted analogues are amorphous with a Mg/(Fe+Mg) ratio of 0.5 tailored to match theoretical abundances in circumstellar dusts. Before the ion implantations were performed, Monte-Carlo-based ion-solid interaction codes were used to model the dynamic redistribution of the implanted atoms in the silicon substrate. 600 keV helium ion irradiation was performed on one of the samples before thermal annealing. Two samples were thermally annealed at a temperature appropriate for an M-class stellar wind, 1000 K, for 8.3 h in a vacuum chamber with a pressure of 1 x 10 -7 torr. The elemental depth profiles were extracted utilizing Rutherford Backscattering Spectrometry (RBS) in the samples before and after thermal annealing. X-ray diffraction (XRD)analysis was employed for the identification of various phases in crystalline minerals in the annealed analogues. Transmission electron microscopy (TEM) analysis was utilized to identify specific crystal structures. RBS analysis shows redistribution of the implanted Fe, Mg, and O after thermal annealing due to incorporation into the crystal structures for each sample type. XRD patterns along with TEM analysis showed nanocrystalline Mg and Fe oxides with possible incorporation of additional silicate minerals.

79 ASTRONOMY AND ASTROPHYSICS↗

PRELIMINARY STUDY OF CERAMICS FOR IMMOBILIZATION OF ADVANCED FUEL CYCLE REPROCESSING WASTES

The Savannah River National Laboratory (SRNL) developed a series of ceramic waste forms for the immobilization of Cesium/Lanthanide (CS/LN) and Cesium/Lanthanide/Transition Metal (CS/LN/TM) waste streams anticipated to result from nuclear fuel reprocessing. Simple raw materials, including Al{sub 2}O{sub 3}, CaO, and TiO{sub 2} were combined with simulated waste components to produce multiphase ceramics containing hollandite-type phases, perovskites (particularly BaTiO{sub 3}), pyrochlores, zirconolite, and other minor metal titanate phases. Identification of excess Al{sub 2}O{sub 3} via X-ray Diffraction (XRD) and Scanning Electron Microscopy with Energy Dispersive Spectroscopy (SEM/EDS) in the first series of compositions led to a Phase II study, with significantly reduced Al{sub 2}O{sub 3} concentrations and increased waste loadings. Three fabrication methodologies were used, including melting and crystallizing, pressing and sintering, and Spark Plasma Sintering (SPS), with the intent of studying phase evolution under various sintering conditions. XRD and SEM/EDS results showed that the partitioning of the waste elements in the sintered materials was very similar, despite varying stoichiometry of the phases formed. The Phase II compositions generally contained a reduced amount of unreacted Al{sub 2}O{sub 3} as identified by XRD, and had phase assemblages that were closer to the initial targets. Chemical composition measurements showed no significant issues with meeting the target compositions. However, volatilization of Cs and Mo was identified, particularly during melting, since sintering of the pressed pellets and SPS were performed at lower temperatures. Partitioning of some of the waste components was difficult to determine via XRD. SEM/EDS mapping showed that those elements, which were generally present in small concentrations, were well distributed throughout the waste forms. Initial studies of radiation damage tolerance using ion beam irradiation at Los Alamos National Laboratory (LANL) showed little if any modification of the material after irradiation. Additional study in this area is needed. Chemical durability was briefly studied using the Product Consistency Test (PCT). Most of the elements measured were retained by the ceramic waste forms, indicating good chemical durability. Cs, Mo, and Rb were released at somewhat higher rates as compared to the matrix components, although benchmark compositions and additional characterization are needed in order to qualify the PCT results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Defect production in strained p-type Si{sub 1-x}Ge{sub x} by Er implantation

Strained p-Si{sub 1-x}Ge{sub x} (x=5.3%, 10.2%, and 15.4%) was irradiated at room temperature with 160 keV {sup 166}Er{sup 2+} ions to a fluence of 1x10{sup 10} or 3x10{sup 13} Er/cm{sup 2}. The defects induced by ion implantation were investigated experimentally using high-resolution x-ray diffraction, Rutherford backscattering and channeling spectroscopy, and deep level transient spectroscopy. X-ray diffraction indicates that the damage induced by Er implantation produces a slight perpendicular expansion of the SiGe lattice. For all compositions, channeling measurements reveal that Er implantation in p-Si{sub 1-x}Ge{sub x} to a fluence of 3x10{sup 13} Er/cm{sup 2} induces an amorphous region below the Si{sub 1-x}Ge{sub x} surface. Annealing at 850 deg. C for 30 s, results in a reduction in damage density, a relaxation of the implantation-induced perpendicular expansion of the SiGe lattice in the implanted region, while a more pronounced relaxation of the compressive strain SiGe is observed for higher Ge content (x=0.10 and 0.15). On the other hand, for the annealed SiGe samples that were implanted with Er at the fluence of 10{sup 10} Er/cm{sup 2}, the compressive strain in the SiGe layer is nearly completely retained. Deep level transient spectroscopy studies indicate that two prominent defects with discrete energy levels above the valence band are introduced during Er implantation. Their activation energy was found to decrease with increasing Ge content. However, the relatively large local strain induced by high fluence Er implantation reduces the activation energy by 40 meV with respect to the low fluence Er implanted p-Si{sub 1-x}Ge{sub x}. This shift (40 meV) in the activation energy remains constant regardless of the Ge content, suggesting that the Si{sub 1-x}Ge{sub x} layers remained fully strained after Er implantation. The observed defects are further compared to those introduced by alpha particle irradiation and electron beam metal deposition. The results indicate that defects introduced by Er implantation have similar electronic properties as those of defects detected after electron beam deposition and alpha particle irradiation. Therefore, it is concluded that these defects are due to the Er implantation-induced damage and not to the Er species specifically.

36 MATERIALS SCIENCE↗

Effect of a novel load-bearing trabecular Nitinol scaffold on rabbit radius bone regeneration

The research aim was to evaluate the bone regeneration capability of novel load-bearing NiTi alloy (Nitinol) scaffolds in a critical-size defect (CSD) model. High strength “trabecular Nitinol” scaffolds were prepared by PIRAC (Powder Immersion Reaction Assisted Coating) annealing of the highly porous Ni foam in Ti powder at 900°C. This was followed by PIRAC nitriding to mitigate the release of potentially toxic Ni ions. Scaffolds phase composition and microstructure were characterized by X-ray diffraction and scanning electron microscopy (SEM/EDS), and their mechanical properties were tested in compression. New Zealand white rabbits received bone defect in right radius and were divided in four groups randomly. In the control group, nothing was placed in the defect. In other groups, NiTi scaffolds were implanted in the defect: (i) as produced, (ii) loaded with bone marrow aspirate (BMA), and (iii) biomimetically CaP-coated. The animals were sacrificed after 12 weeks. The forelimbs with scaffolds were resected, fixed, sectioned and examined in SEM. New bone formation inside the scaffold was studied by EDS analysis and by the processing of backscattered electron images. Bone ingrowth into the scaffold was observed in all implant groups, mostly next to the ulna. New bone formation was strongly enhanced by BMA loading and biomimeatic CaP coating, the bone penetrating as much as 1–1.5 mm into the scaffold. The results of this preliminary study demonstrate that the newly developed high strength trabecular Nitinol scaffolds can be successfully used for bone regeneration in critical size defects.

36 MATERIALS SCIENCE↗

Use of aluminum oxide as a permeation barrier for producing thin films on aluminum substrates

Aluminum has desirable characteristics of good thermal properties, good electrical characteristics, good optical properties, and the characteristic of being nonmagnetic and having a low atomic weight (26.98 g atoms), but because of its low melting point (660 °C) and ability as a reactive metal to alloy with most common metals in use, it has been ignored as a substrate material for use in processing thin films. The author developed a simple solution to this problem, by putting a permeation barrier of alumina (Al{sub 2}O{sub 3}) onto the surface of pure Al substrates by using a standard chemical oxidation process of the surface (i.e., anodization), before additional film deposition of reactive metals at temperatures up to 500 °C for 1-h, without the formation of alloys or intermetallic compounds to affect the good properties of Al substrates. The chromic acid anodization process used (MIL-A-8625) produced a film barrier of ∼(500–1000) nm of alumina. The fact that refractory Al{sub 2}O{sub 3} can inhibit the reaction of metals with Al at temperatures below 500 °C suggests that Al is a satisfactory substrate if properly oxidized prior to film deposition. To prove this concept, thin film samples of Cr, Mo, Er, Sc, Ti, and Zr were prepared on anodized Al substrates and studied by x-ray diffraction, Rutherford ion back scattering, and Auger/argon sputter surface profile analysis to determine any film substrate interactions. In addition, a major purpose of our study was to determine if ErD{sub 2} thin films could be produced on Al substrates with fully hydrided Er films. Thus, a thin film of ErD{sub 2} on an anodized Al substrate was prepared and studied, with and without the alumina permeation barrier. Films for study were prepared on 1.27 cm diameter Al substrates with ∼500 nm of the metals studied after anodization. Substrates were weighed, cleaned, and vacuum fired at 500 °C prior to use. The Al substrates were deposited using standard electron beam cold crucible evaporation techniques, and after deposition the Er film was hydrided with D{sub 2} gas using a standard nonair exposure hydriding technique. All processing was conducted in an all metal ion pumped ultrahigh vacuum system. Results showed that e-beam deposition of films studied onto Al substrates could be successfully performed, if a permeation barrier of Al{sub 2}O{sub 3} from 500 to 1000 nm was made prior to thin film deposition up to temperatures of 500 °C for 1-h. Hydrides also, could be produced with full gas/metal atomic ratios of ∼2.0 as evidenced by the ErD{sub 2} films produced. Thus, the use of a simple permeation barrier of Al{sub 2}O{sub 3} on Al substrates prior to additional metal film deposition was proven to be a successful method of producing both thin metal films and hydride films of various types for many applications.

36 MATERIALS SCIENCE↗

Growth of GaP1 − x − yAsyNx on Si substrates by chemical beam epitaxy

Chemical beam epitaxy has been used to grow layers of GaP1 − xNx, GaP1 − yAsy, and nearly lattice-matched layers GaP1 − x − yAsyNx on Si substrates. To address the issue of antiphase domain generation associated with the growth of polar semiconductors on Si, misoriented Si(001) substrates have been used combined with a carefully designed GaP buffer layer growth. The reflection high-energy electron diffraction pattern exhibits a (2 × 4) surface reconstruction after GaP buffer layer and GaP(As,N) graded layer growth, indicating the good surface quality and planarity of the grown layers. Sample composition was obtained by simultaneous acquisition of Rutherford backscattering spectrometry and nuclear reaction analysis, indicating a linear dependence of N and As mole fractions on the flux of their respective precursor. GaP1 − x − yAsyNx layers grown on Si substrates have a lattice mismatch not larger than ±0.005 for N contents in the range 0.02 < x < 0.05. High-resolution X-ray diffraction reciprocal space maps demonstrate a good crystalline quality. Intense photoluminescence spectra have been measured in all GaP1 − xNx and GaP1 − x − yAsyNx layers, as it is expected for direct bandgap materials. Two wide overlapped emission peaks are observed in all the spectra, most likely related to near bandgap recombination. The position of the higher energy peak for GaP1 − xNx and GaP1 − x − yAsyNx layers has been compared to bandgap energy calculations using the band anticrossing model, showing good agreement.

Ben Saddik, K.↗

Diamond x-ray optics: Transparent, resilient, high-resolution, and wavefront preserving

Diamond features a unique combination of outstanding physical properties perfect for numerous x-ray optics applications, where traditional materials such as silicon fail to perform. In the last two decades, impressive progress has been achieved in synthesizing diamond with high crystalline perfection, in manufacturing efficient, resilient, high-resolution, wavefront-preserving diamond optical components, and in implementing them in cutting-edge x-ray instruments. Diamond optics are essential for tailoring x-rays to the most challenging needs of x-ray research. Furthermore, they are becoming vital for the generation of fully coherent hard x-rays by seeded x-ray free-electron lasers. In this article, we review progress in manufacturing flawless diamond crystal components and their applications in diverse x-ray optical devices, such as x-ray monochromators, beam splitters, high-reflectance backscattering mirrors, lenses, phase plates, diffraction gratings, bent-crystal spectrographs, and windows.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

La 0.6 Sr 0.4 CoO 3−δ Films Under Deoxygenation: Magnetic And Electronic Transitions Are Apart from The Structural Phase Transition

Abstract Topotactic phase transitions induced by changes in the oxygen vacancy concentration can largely alter the physical properties of complex oxides, including electronic and magnetic phases, while maintaining the structural integrity of the crystal lattice. An oxygen‐vacancy‐induced topotactic phase transition from perovskite (PV) to brownmillerite (BM) is achieved in epitaxial La 0.6 Sr 0.4 CoO 3−δ (LSCO) thin films. Two novel intermediate states with different oxygen content are identified by X‐ray diffraction, which involves a single‐phase reduced PV state and a mixed state of co‐existing PV and BM. The combination of depth‐sensitive polarized neutron reflectometry (PNR) and Rutherford backscattering (RBS) allows a quantitative determination of magnetization and the mean oxygen content in all states, revealing a continuous transition from La 0.6 Sr 0.4 CoO 2.97 to La 0.6 Sr 0.4 CoO 2.5 . BM formation is observed for an LSCO layer with an oxygen content of 2.67, while the magnetic and electronic transition already occurs for a layer with a higher oxygen content of 2.77 (and above) and in the absence of a BM signature. These results demonstrate that the physics of electronic metal‐to‐insulator transition (MIT), magnetic ferromagnet‐to‐non‐ferromagnet transition (FM‐to‐non‐FM), and structural PV‐to‐BM phase transition should be considered within the framework of separate but interrelated processes.

36 MATERIALS SCIENCE↗

New Homogeneous Standards by Atomic Layer Deposition for Synchrotron X-ray Fluorescence and Absorption Spectroscopies.

Quantification of synchrotron XRF analyses is typically done through comparisons with measurements on the NIST SRM 1832/1833 thin film standards. Unfortunately, these standards are inhomogeneous on small scales at the tens of percent level. We are synthesizing new homogeneous multilayer standards using the Atomic Layer Deposition technique and characterizing them using multiple analytical methods, including ellipsometry, Rutherford Back Scattering at Evans Analytical, Synchrotron X-ray Fluorescence (SXRF) at Advanced Photon Source (APS) Beamline 13-ID, Synchrotron X-ray Absorption Spectroscopy (XAS) at Advanced Light Source (ALS) Beamlines 11.0.2 and 5.3.2.1 and by electron microscopy techniques. Our motivation for developing much-needed cross-calibration of synchrotron techniques is borne from coordinated analyses of particles captured in the aerogel of the NASA Stardust Interstellar Dust Collector (SIDC). The Stardust Interstellar Dust Preliminary Examination (ISPE) team have characterized three sub-nanogram, {approx}1{micro}m-sized fragments considered as candidates to be the first contemporary interstellar dust ever collected, based on their chemistries and trajectories. The candidates were analyzed in small wedges of aerogel in which they were extracted from the larger collector, using high sensitivity, high spatial resolution >3 keV synchrotron x-ray fluorescence spectroscopy (SXRF) and <2 keV synchrotron x-ray transmission microscopy (STXM) during Stardust ISPE. The ISPE synchrotron techniques have complementary capabilities. Hard X-ray SXRF is sensitive to sub-fg mass of elements Z {ge} 20 (calcium) and has a spatial resolution as low as 90nm. X-ray Diffraction data were collected simultaneously with SXRF data. Soft X-ray STXM at ALS beamline 11.0.2 can detect fg-mass of most elements, including cosmochemically important oxygen, magnesium, aluminum and silicon, which are invisible to SXRF in this application. ALS beamline 11.0.2 has spatial resolution better than 25 nm. Limiting factors for Stardust STXM analyses were self-imposed limits of photon dose due to radiation damage concerns, and significant attenuation of <1500 eV X-rays by {approx}80{micro}m thick, {approx}25 mg/cm{sup 3} density silica aerogel capture medium. In practice, the ISPE team characterized the major, light elements using STXM (O, Mg, Al, Si) and the heavier minor and trace elements using SXRF. The two data sets overlapped only with minor Fe and Ni ({approx}1% mass abundance), providing few quantitative cross-checks. New improved standards for cross calibration are essential for consortium-based analyses of Stardust interstellar and cometary particles, IDPs. Indeed, they have far reaching application across the whole synchrotron-based analytical community. We have synthesized three ALD multilayers simultaneously on silicon nitride membranes and silicon and characterized them using RBS (on Si), XRF (on Si{sub 3}N{sub 4}) and STXM/XAS (holey Si{sub 3}N{sub 4}). The systems we have started to work with are Al-Zn-Fe and Y-Mg-Er. We have found these ALD multi-layers to be uniform at {micro}m- to nm scales, and have found excellent consistency between four analytical techniques so far. The ALD films can also be used as a standard for e-beam instruments, eg., TEM EELS or EDX. After some early issues with the consistency of coatings to the back-side of the membrane windows, we are confident to be able to show multi-analytical agreement to within 10%. As the precision improves, we can use the new standards to verify or improve the tabulated cross-sections.

43 PARTICLE ACCELERATORS↗

Investigations on hydrogen storage properties of Mg{sub 2}Ni+x wt% LaMg{sub 2}Ni (x=0, 10, 20, 30) composites

Mg{sub 2}Ni+x wt% LaMg{sub 2}Ni (x=0, 10, 20, 30) composites have been prepared by ball milling Mg{sub 2}Ni and LaMg{sub 2}Ni hydrides. X-ray Diffraction indicates that the composites consist of LaH{sub 3} and Mg{sub 2}NiH{sub 4} phases. Mg{sub 2}NiH{sub 4} phase transforms between with Mg{sub 2}Ni phase during hydriding/dehydriding cycling, while the LaH{sub 3} phase exists still after dehydriding process. Backscatter Electron results reveal that the LaH{sub 3} phase, which is decomposed from hydrided LaMg{sub 2}Ni, distributes in Mg{sub 2}Ni alloy homogeneously after ball milling procedure. Hydriding/Dehydriding measurements indicate significant improvement in reversible hydrogen storage properties of the composites over Mg{sub 2}Ni at low temperature. At 473 K, the hydrogen storage capacity of Mg{sub 2}Ni+20 wt% LaMg{sub 2}Ni composite reaches 3.22 wt% and can reversely desorb hydrogen completely, while the pure Mg{sub 2}Ni hydride is hardly desorbs hydrogen at this temperature. The improvement in the hydrogen storage properties is attributed to the existence of LaH{sub 3} phase in the composites. - Graphical abstract: The Mg{sub 2}Ni + x wt% LaMg{sub 2}Ni (x=10, 20, 30) composites display enhancement on reversible hydrogen storage properties compared with that of pure Mg{sub 2}Ni. Highlights: Black-Right-Pointing-Pointer Tittle La is introduced into Mg{sub 2}Ni alloy without multiphase created. Black-Right-Pointing-Pointer La is introduced into Mg{sub 2}Ni by hydrogen decomposed ball-milling. Black-Right-Pointing-Pointer Reversible hydrogen storage properties at low temperature are improved. Black-Right-Pointing-Pointer Hydrogen storage capacity of composites is beyond 3 wt% at 473 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Segregation and formation of MnP particles during rapid thermal annealing of Mn-implanted InP and GaP

We have studied the structural and magnetic properties of Mn implanted (1-5x10{sup 16} cm{sup -2}, 200 keV) into InP and GaP substrates, before and after rapid thermal annealing. As revealed by Rutherford backscattering spectrometry, secondary ion mass spectrometry, and transmission electron microscopy measurements, implantation results in an amorphous surface layer 300 nm deep, and subsequent annealing gives rise to epitaxial recrystallization of this layer accompanied by a segregation of most of the Mn into clusters about 60 nm in diameter at the surface. Magnetic measurements indicate ferromagnetic behavior only for the annealed samples with T{sub C} close to 290 K, characteristic of bulk MnP, whose presence is confirmed by diffraction data. In addition, there is no evident dependence of the magnetic and structural properties on the doping type or level of the substrates.

36 MATERIALS SCIENCE↗