Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Mechanical characterization of Bi-2212 composite winding pack samples for high-field superconducting magnet design

Bi₂Sr₂CaCu₂O8−x (Bi-2212) multi-filament round wire is a high-temperature superconductor (HTS) capable of carrying high transport currents, which makes it suitable for high-field magnet applications. However, its weak Ag–Mg sheath leaves it vulnerable to mechanical stress, posing challenges for high-field magnet design. To better understand and improve mechanical stress management in Bi-2212 winding packs, we conducted an experimental study evaluating the axial stress–strain behavior of five winding pack configurations with varying insulation materials, reinforcement strategies, and construction quality. Using uniaxial tensile testing at 77 K, we measured Young’s modulus and Poisson’s ratio for each composition. Our results show that pure alumina braid insulation and co-wind reinforcements significantly enhance stiffness compared to aluminosilicate braids, with more than 2.5 times increased winding pack Young’s modulus. Rule of mixtures analysis further quantified the contribution of non-wire composite components to overall stiffness. These findings highlight the critical role of insulation material selection and reinforcement design in optimizing Bi-2212 coil performance under stress, providing a foundation for improved mechanical models and more reliable high-field HTS magnet designs.

Bi-2212 magnet↗

Thermoelastic properties of tungsten at simultaneous high pressure and temperature

In this work, the compressional ( P ) and shear wave velocities ( S ) and unit cell volumes (densities) of polycrystalline tungsten (W) have been measured simultaneously up to 10.5 GPa and 1073 K using ultrasonic interferometry in conjunction with x-ray diffraction and x-radiography techniques. Thermoelastic properties of W were derived using different methods. We obtained the isothermal bulk modulus K T 0 = 310.3(1.5) GPa, its pressure derivative K ' T 0 = 4.4(3), its temperature derivative at constant pressure ( ∂ K T / ∂ T ) P = – 0.0138 ( 1 ) GPa K – 1 and at constant volume ( ∂ K T / ∂ T ) V = – 0.0050 GPa K – 1 , the thermal expansion α ( 0, T ) = 1.02(27) × 10 –5 + 7.39(3.2) × 10 –9 T (K –1 ), as well as the pressure derivative of thermal expansion ( ∂ α / ∂ P ) T = – 1.44 ( 1 ) × 10 – 7 K – 1 GP a – 1 based on the high-temperature Birch–Murnaghan equation of state (EOS), the Vinet EOS, and thermal pressure approach. Finite strain analysis allowed us to derive the elastic properties and their pressure/temperature derivatives independent of the choice of pressure scale. A least-squares fitting yielded K S 0 = 314.5(2.5) GPa, K S 0 ' = 4.45(9), (∂ K S /∂ T ) P = – 0.0076(6) GPa K –1 , G 0 = 162.4(9) GPa, G 0 ' = 1.8(1), (∂ G /∂ T ) P = – 0.0175(9) GPa K –1 , and α 298 K = 1.23 × 10 – 5 K – 1 . Fitting current data to the Mie–Grüneisen–Debye EOS with derived θ 0 = 383.4 K yielded γ 0 = 1.81 ( 6 ) and q = 0.3 . The thermoelastic parameters obtained from various approaches are consistent with one another and comparable with previous results within uncertainties. Our current study provides a complete and self-consistent dataset for the thermoelastic properties of tungsten at high P – T conditions, which is important to improve the theoretical modeling of these materials under dynamic conditions.

36 MATERIALS SCIENCE↗

Impact of biomass ash content on biocomposite properties

Owing to its low cost and sustainable nature, lignocellulosic biomass has been utilized for reinforcing polymers, but it is crucial to understand the impact of high-ash concentrations in biomass on composite strength and processing. Biomass is not only desirable for biofuel production but could also have a strong market, if high-ash biomass is acceptable, for biocomposites. In this work, natural fibers (switchgrass and corn stover) were used to reinforce polylactic acid (PLA) to produce biocomposites. Natural fibers were pretreated to obtain fibers that contain different percentages of ash. The mechanical properties (such as Young's modulus, tensile strength, failure strain, storage modulus) of corn stover/PLA composites remained largely unaffected by the ash concentration of the biomass fibers, despite the large range of ash contents (2.2–11.9 wt%). Furthermore, the tensile strengths of switchgrass/PLA composites were slightly negatively affected by the ash concentration of the switchgrass fibers (0.7–2.1 wt%). Both the switchgrass/PLA and the corn stover/PLA composites exhibited a high-enough tensile strength (49–57 MPa) and suitable complex viscosity (2.0–7.0 kPa·s at the frequency of 3.2 rad/s). They are expected to be 3D-printable through an extrusion-based additive manufacturing process.

36 MATERIALS SCIENCE↗

Multiscale Modeling of Thermoplastics Using Atomistic-informed Micromechanics

A multiscale repeating unit cell model of a single spherulite containing four disparate length scales was developed to predict the thermoelastic behavior of semicrystalline thermoplastic materials for composite aerospace applications. The continuum level scales were fully coupled and modeled using the generalized method of cells and the high fidelity generalized method of cells micromechanics theories. Data from molecular dynamics simulations were used as inputs for the amorphous and crystalline constituents in the multiscale continuum models. Effective Young’s modulus, shear modulus, Poisson’s ratio, coefficient of thermal expansion, and thermal conductivity were predicted for polyether ether ketone and polyether ketone ketone, showing good agreement with the available experimental data from the open literature. Moreover, it is shown that predicted properties are fairly insensitive to the fidelity of the micromechanics model used at the highest continuum scale or the assumed shape of the spherulite.

thermoplastics↗

Strength and elastic moduli of TiN from radial x-ray diffraction under nonhydrostatic compression up to 45 GPa

The high pressure behavior of titanium nitride (TiN) was investigated using synchrotron radial x-ray diffraction (RXRD) under nonhydrostatic compression up to 45.4 GPa in a diamond-anvil cell. We obtained the hydrostatic compression equation of state of TiN. Fitting to the third-order Birch-Murnaghan equation of state, the bulk modulus derived from nonhydrostatic compression data varies from 232 to 353 GPa, depending on angle {Psi}, the orientation of the diffraction planes with respect to the loading axis. The RXRD data obtained at {Psi} = 54.7{sup o} yield a bulk modulus K{sub 0} = 282 {+-} 9 GPa with pressure derivative K{prime}{sub 0} fixed at 4. We have analyzed the deformation mechanisms by analyzing the (111), (200), (220), (311), and (222) peaks in the x-ray diffraction under pressures. The ratio of uniaxial stress component to shear modulus t/G ranges from 0.007-0.027 at the pressure of 6.4-45.4 GPa. It was found that the TiN sample could support a maximum uniaxial stress component t of 8.6 GPa, when it started to yield at 45.4 GPa under uniaxial compression. And the aggregate elastic moduli of TiN at high pressure were determined from the synchrotron RXRD measurements.

43 PARTICLE ACCELERATORS↗

Temperature effect of elastic anisotropy and internal strain development in advanced nanostructured alloys: An in-situ synchrotron X-ray investigation

Nanostructured ferritic alloys (NFAs) are a promising structural material for advanced nuclear systems due to their exceptional radiation tolerance and high-temperature mechanical properties. Their remarkable properties result from the ultrafine ultrahigh density Y-Ti-O nanoclusters dispersed within the ferritic matrix. In this work, we performed in-situ synchrotron X-ray diffraction tests to study the tensile deformation process of the three types of NFAs: 9YWTV, 14YWT-sm13, and 14YWT-sm170 at both room temperature and elevated temperatures. A technique was developed, combining Kroner’s model and X-ray measurement, to determine the intrinsic monocrystal elastic-stiffness constants, and polycrystal Young’s modulus and Poisson’s ratio of the NFAs. Temperature dependence of elastic anisotropy was observed in the NFAs. An analysis of intergranular strain and strengthening factors determined that 14YWT-sm13 had a higher resistance to temperature softening compared to 9YWTV, attributed to the more effective nanoparticle strengthening during high-temperature mechanical loading.

Gan, Yingye↗

Evaluating the irradiation effects on the elastic properties of miniature monolithic SiC tubular specimens

The initial results of a post-irradiation examination study conducted on CVD SiC tubular specimens irradiated under a high radial heat flux are presented herein. The elastic moduli were found to decrease more than that estimated based on previous studies. The significant decreases in modulus are attributed to the cracks present in the specimens. The stresses in the specimens, calculated through finite element analyses, were found to be greater than the expected strength of irradiated specimens, indicating that the irradiation-induced stresses caused these cracks. In conclusion, the optical microscopy images and predicted stress distributions indicate that the cracks initiated at the inner surface and propagated outward.

36 MATERIALS SCIENCE↗

Characteristics of kinetic sprayed Ta in terms of the deposition behavior, microstructural evolution and mechanical properties: Effect of strain-rate-dependent response of Ta at high temperature

Highlights: • The effect of high-temperature rate-dependent response of BCC Ta on the deposition state of kinetic sprayed Ta particles with synergistic effect of powder oxidation • Abnormal increase of dislocation density above certain powder preheating temperature under the lower condition (N{sub 2} carrier gas), whereas considerable occurrence of grain refinement under the higher condition (He carrier gas). • Most significant dislocation density with the smallest volume-averaged domain size under the condition of 600 {sup o}C powder pre-heating with N{sub 2} carrier gas due to characteristic response of Ta. - Abstract: Numerous efforts have been focused on the fundamental research regarding kinetic spraying processes, but previous studies were biased to only few kinds of metallic materials. In particular, for Ta with body-centered cubic crystal structure, systematic studies are currently lacking in the literature. In this study, the characteristic deposition behaviors, microstructures, and mechanical properties of kinetic sprayed Ta under various impact conditions were systematically investigated. Generally, unusual features were usually related to strain-rate-dependent response (i.e. Peierls-Nabarro short range barriers) of Ta at high-temperature. This made thermal softening effect to be saturated above a certain degree of temperature, contributing to inferior deposition efficiency for the pre-heating at 600 °C than those of 400 and 500 °C by creating synergy with powder oxidation. In terms of microstructural evolutions, the dislocation density was abnormally increased at a certain powder preheating temperature (i.e., 600 °C), owing to the strain-rate-dependent response of Ta at high-temperature. On the other hand, grain refinement generated by rotational dynamic recrystallization was mainly observed under the higher kinetic energy condition (He carrier gas) at RT. Especially, the dislocation density and volume-average domain size evaluated via high-resolution X-ray diffraction peak profile analysis were corresponding to the results of the microstructural observations. Additionally, the nanomechanical properties (i.e., nanohardness and elastic modulus) evaluated via nanoindentation tests were in good agreement with the results from transmission electron microscopy investigations.

36 MATERIALS SCIENCE↗

Spray Manufacturing Thermal Insulation Composites

Cellulose-based thermal insulation materials present significant potential for modern green building applications due to their inherent carbon sequestration properties. However, traditional manufacturing of composites often results in the limited thermal insulation performance and embodied carbon footprint due to an increased density from material shrinkage and higher energy consumption during the water-based slurry drying process. Here, we report solvent spraying coupled with dry powder feedstock to manufacture highly porous silica/straw insulation composites. The manufactured composite exhibits negligible shrinkage with the density of 0.08 g/cm 3 , thermal conductivity of 27.8 mW/(m·K), flexural modulus of 3.1 MPa, and compressive modulus of 0.89 MPa. Additionally, the prepared composite demonstrates fire retardancy (burning rate of 0.5 mm/min) and recyclability (99%). Furthermore, this solvent-spraying strategy opens up opportunities of energy-efficient insulation materials for carbon-sequestration building sectors.

36 MATERIALS SCIENCE↗

Å-Indentation for non-destructive elastic moduli measurements of supported ultra-hard ultra-thin films and nanostructures

During conventional nanoindentation measurements, the indentation depths are usually larger than 1–10 nm, which hinders the ability to study ultra-thin films (<10 nm) and supported atomically thin two-dimensional (2D) materials. Here, we discuss the development of modulated Å-indentation to achieve sub-Å indentations depths during force-indentation measurements while also imaging materials with nanoscale resolution. Modulated nanoindentation (MoNI) was originally invented to measure the radial elasticity of multi-walled nanotubes. Now, by using extremely small amplitude oscillations (<<1 Å) at high frequency, and stiff cantilevers, we show how modulated nano/Å-indentation (MoNI/ÅI) enables non-destructive measurements of the contact stiffness and indentation modulus of ultra-thin ultra-stiff films, including CVD diamond films (~1000 GPa stiffness), as well as the transverse modulus of 2D materials. Our analysis demonstrates that in presence of a standard laboratory noise floor, the signal to noise ratio of MoNI/ÅI implemented with a commercial atomic force microscope (AFM) is such that a dynamic range of 80 dB –– achievable with commercial Lock-in amplifiers –– is sufficient to observe superior indentation curves, having indentation depths as small as 0.3 Å, resolution in indentation <0.05 Å, and in normal load <0.5 nN. Being implemented on a standard AFM, this method has the potential for a broad applicability.

36 MATERIALS SCIENCE↗

Electron-ion plasma modification of Al-based alloys

The paper reports on the study where we analyzed the surface structure and strength properties of coated Al alloys modified by electron-ion plasma treatment. The Al alloys were deposited with a thin (≈0.5 μm) TiCu film coating (TiCu-Al system) and with a hard TiCuN coating (TiCuN–AlSi system) on a TRIO vacuum setup in the plasma of low-pressure arc discharges. The temperature fields and phase transformations in the film–substrate system were estimated by numerical simulation in a wide range of electron energy densities (5–30 J/cm{sup 2}) and pulse durations (50–200 μs). The calculations allowed us to determine the threshold energy density and pulse duration at which the surface structure of the irradiated Al-based systems is transformed in a single-phase state (solid or liquid) and in a two-phase state (solid plus liquid). The elemental composition, defect structure, phase state, and lattice state in the modified surface layers were examined by optical, scanning, and transmission electron microscopy, and by X-ray diffraction analysis. The mechanical characteristics of the modified layers were studied by measuring the hardness and Young’s modulus. The tribological properties of the modified layers were analyzed by measuring the wear resistance and friction coefficient. It is shown that melting and subsequent high-rate crystallization of the TiCu–Al system makes possible a multiphase Al-based surface structure with the following characteristics: crystallite size ranging within micrometer, microhardness of more than 3 times that in the specimen bulk, and wear resistance ≈1.8 times higher compared to the initial material. Electron beam irradiation of the TiCuN–AlSi system allows fusion of the coating into the substrate, thus increasing the wear resistance of the material ≈2.2 times at a surface hardness of ∼14 GPa.

36 MATERIALS SCIENCE↗

Compression of bulk metallic glass Zr[subscript 57]Cu[subscript 15.4]Ni[subscript 12.6]Al[subscript 10]Nb[subscript 5] to 122 GPa

Ultra high pressure X-ray diffraction studies have been carried out on group IV transition metals-based bulk metallic glass (BMG) Zr{sub 57}Cu{sub 15.4}Ni{sub 12.6}Al{sub 10}Nb{sub 5} to a pressure of 122 GPa at ambient temperature in a diamond anvil cell. Image plate X-ray diffraction studies under high pressure were carried out at a synchrotron source and the two BMG diffraction bands can be followed to the highest pressure using an internal copper pressure standard. Our experiments show that the BMG is stable to compression as high as 40% and thermal activation is needed to nucleate nanostructures/crystallization under extreme conditions. The fit to the Birch-Murnaghan equation of state gives bulk modulus (B{sub 0}) = 116 GPa and its pressure derivative B' = 3.04. The measured differential radial distribution function shows gradual compression of the shell structures in the BMG to extreme compressions.

36 MATERIALS SCIENCE↗

High Pressure X-ray Diffraction Study of Titanium Disulfide

A high pressure angle dispersive synchrotron x-ray diffraction study of titanium disulfide (TiS2) was carried out to pressures of 45.5 GPa in a diamond-anvil cell. We observed a phase transformation of TiS2 beginning at about 20.7 GPa. The structure of the high pressure phase needs further identification. By fitting the pressure-volume data to the third-order Birch-Murnaghan equation of state, the bulk modulus, K0T, was determined to be 45.9 {+-} 0.7 GPa with its pressure derivative, K'0T, being 9.5 {+-} 0.3 at pressures lower than 17.8 GPa. It was found that the compression behavior of TiS2 is anisotropic along the different axes. The compression ratio of the c-axis is about nine times larger than the a-axis when pressures are lower than 1 GPa. It suddenly decreases to three times larger at pressures of about 3 GPa. This ratio shows a linear decrease with a slope of negative 0.048 at pressures below phase transformation.

43 PARTICLE ACCELERATORS↗

Decomposition of W(CO)[subscript 6] at high pressures and temperatures

The decomposition of hexacarbonyltungsten, W(CO){sub 6}, has been studied. The decomposition was induced by heating W(CO){sub 6} in an autoclave at 523 K and pressures up to 1.8 MPa, and by laser heating in a diamond anvil cell at pressures between 5 and 18 GPa. The products have been characterized using synchrotron X-ray diffraction, pair distribution function analysis, Raman spectroscopy and scanning electron microscopy. Decomposition in the autoclave at the lower pressures resulted in the formation of a metastable tungsten carbide, W{sub 2}C, with an average particle size of 1-2 nm, and an unidentified nanocrystalline tungsten oxide and nanocrystalline graphite with average particle sizes of 1-2 and 11 nm, respectively. The existence of nanocrystalline graphite was deduced from micro-Raman spectra and the graphite particle size was extracted from the intensities of the Raman modes. The high-pressure decomposition products obtained in the diamond anvil cell are the monoclinic tungsten oxide phase WO{sub 2} and the high-pressure phase W{sub 3}O{sub 8}(I). The approximate average size of the graphite particles formed here was 6-8 nm. The bulk modulus of W(CO){sub 6} is B{sub 0} {approx_equal} 13 GPa.

36 MATERIALS SCIENCE↗

Large-Area Lithium Electrode Sub-Assemblies (LESAs) Protected by Self Forming Microstructured Polymer-Inorganic Single-Ion Conducting Composites (Final Report)

The aim of this project is to realize a low-cost, safe, reversible, high-areal capacity lithium metal electrode though the use of scalable, low-cost Lithium Electrode Sub-Assembly (LESA). At its core, the LESA applies novel polymer scaffolds to nanostructure inorganic ionic materials into high-conductivity composites that stabilize lithium anodes during high-rate, high-capacity cycling in lithium metal batteries. Fundamental investigations from this project identified a newly defined region of stability for composites with respect to the shear modulus and lithium molar volume ratio which have been broadly applied in the scientific literature for a multitude of different systems. The advancements achieved in this field have furthered the fundamental understanding of lithium metal electrode chemistry and degradation mechanisms and resulted in a lithium metal anode with improved cycle life.

25 ENERGY STORAGE↗

An investigation of the thermal cycling damage of 25 vol. pct SiCw/alumina ceramic matrix composite

An investigation was made of the thermal cycling damage of a 25 vol pct SiC whisker/alumina (SiCw/Al2O3) composite. Thermal cycling tests were conducted by subjecting a composite specimen to two different fluidized beds. After thermal cycling the composite specimens were subjected to elastic modulus and effective fracture toughness measurements. The thermal cycled specimens were investigated with SEM and TEM studies. It was found that this composite has a relatively high resistance to thermal cycling.

Armstrong, William D.↗

Synthesis and Properties of Cross-Linked Polyamide Aerogels

We report our ongoing research on polyamide aerogels made by step growth polymerization using a combination of terephthaloyl chloride, isophthaloyl chloride and m-phenylenediamine. Crosslinking of the amine capped polymer chains with 1,3,5-benzenetricarbonyl trichloride causes gelation in as little as two to five minutes. Removing the reaction solvent is accomplished through solvent exchange, followed by drying using supercritical CO2 extraction to give colorless aerogels with densities ranging from 0.07 to 0.33 grams per cubic centimeter and surface areas as high as 440 square meters per gram. Statistical experimental design methodology has been utilized to investigate dependence of properties of these aerogels, such as density, compressive modulus, and surface area, on changes in fabrication parameters including formulated number of amide oligomer repeat units (n-value), acid chloride (meta, para or combination), and solids concentration of solution used for gelation. For example, the density of these materials was found to be dependent on the acid chloride type and the solids concentration, but n was not a significant variable. However, surface area was significantly influenced by all three parameters. The polyamide aerogels represent a potential cost savings over previously reported polyimide aerogels, since monomers are all inexpensive and commercially available. Surface area and density were both highest when 100 terephthaloyl chloride was used but a combination of 5 solid concentration, 100 terephthaloyl chloride and n of 20 gave the best combination of properties.

cross-linked↗

Application of Nonlinear Elastic Resonance Spectroscopy For Damage Detection In Concrete: An Interesting Story

Nonlinear resonance ultrasound spectroscopy experiments conducted on concrete cores, one chemically and mechanically damaged by alkali-silica reactivity, and one undamaged, show that this material displays highly nonlinear wave behavior, similar to many other damaged materials. They find that the damaged sample responds more nonlinearly, manifested by a larger resonant peak and modulus shift as a function of strain amplitude. The nonlinear response indicates that there is a hysteretic influence in the stress-strain equation of state. Further, as in some other materials, slow dynamics are present. The nonlinear response they observe in concrete is an extremely sensitive indicator of damage. Ultimately, nonlinear wave methods applied to concrete may be used to guide mixing, curing, or other production techniques, in order to develop materials with particular desired qualities such as enhanced strength or chemical resistance, and to be used for damage inspection.

54 ENVIRONMENTAL SCIENCES↗