Search NASA⌕ Search

SEARCH · Search NASA

Results for “parallel simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Comparison of Parallel and Series Hybrid Power Trains for Transit Bus Applications

The fuel economy and emissions of conventional and hybrid buses equipped with emissions after treatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicated that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar carbon monoxide and hydrocarbon tailpipe emissions but were also predicted to have reduced tailpipe emissions of nitrogen oxides compared with the conventional bus in higher speed cycles. For the New York bus cycle, which has the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus; the parallel hybrid bus had significantly lower tailpipe emissions. All three bus power trains were found to require periodic active diesel particulate filter regeneration to maintain control of particulate matter. Finally, plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed because of the relatively large battery capacity that is typical of the series hybrid configuration.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Compact lumped circuit model of discharges in DC accelerator using partial element equivalent circuit

DC Accelerators undergoes different types of discharges during its operation. A model depicting the discharges has been simulated to study the different transient conditions. The paper presents a Physics based approach of developing a compact circuit model of the DC Accelerator using Partial Element Equivalent Circuit (PEEC) technique. The equivalent RLC model aids in analyzing the transient behavior of the system and predicting anomalies in the system. The electrical discharges and its properties prevailing in the accelerator can be evaluated by this equivalent model. A parallel coupled voltage multiplier structure is simulated in small scale using few stages of corona guards and the theoretical and practical results are compared. The PEEC technique leads to a simple model for studying the fault conditions in accelerator systems. Compared to the Finite Element Techniques, this technique gives the circuital representation. The lumped components of the PEEC are used to obtain the input impedance and the result is also compared to that of the FEM technique for a frequency range of (0-200) MHz. (author)

43 PARTICLE ACCELERATORS↗

Inverter-Based Operation of Maui: Electromagnetic Transient Simulations

As larger and larger power systems approach and reach 100% inverter-based resource (IBR) operation during some hours of the year, questions arise regarding the stability of such extremely-high IBR power systems, the potential need for grid-forming (GFM) inverter technology, and the potential need for synchronous condensers. Relatedly, questions also arise about the ability of conventional positive sequence power system modeling tools to capture high-IBR system dynamics. This presentation introduces electromagnetic transient (EMT) simulations in PSCAD of the near-future (year 2023) Maui power system at and near 100% IBR operation and compares those simulations to positive sequence (PSSE) simulations. The Maui PSCAD model is parallelized on 30 cores and includes the entire transmission system (>200 three-phase buses), >170 individual and aggregate IBR models, four wind plants, and three synchronous generators plus six synchronous condensers at two locations. We investigate system stability with varying levels of inertia using conventional grid-following IBR controls, and then we investigate the impact of GFM controls on stability. Results suggest that: 1) positive sequence simulations can miss key dynamics in extremely high IBR cases; 2) EMT simulations can also miss key dynamics if inverter inner control dynamics are not modeled; 3) synchronous condensers can stabilize a system in which 100% of the energy is supplied by IBRs, even conventional grid-following IBRs; 4) GFM controls on just some of the IBRs can stabilize a 100% IBR power system, even if that system has zero inertia (i.e. no synchronous condensers, though synchronous condensers may be needed for other purposes such as protection system operations).

41 EE - Solar Energy Technologies Office (EE-4S)↗

Parallel Harmony Search Based Distributed Energy Resource Optimization

This paper presents a harmony search based parallel optimization algorithm to minimize voltage deviations in three phase unbalanced electrical distribution systems and to maximize active power outputs of distributed energy resources (DR). The main contribution is to reduce the adverse impacts on voltage profile during a day as photovoltaics (PVs) output or electrical vehicles (EVs) charging changes throughout a day. The IEEE 123- bus distribution test system is modified by adding DRs and EVs under different load profiles. The simulation results show that by using parallel computing techniques, heuristic methods may be used as an alternative optimization tool in electrical power distribution systems operation.

Ceylan, Oguzhan↗

In‐memory integration of existing software components for parallel adaptive unstructured mesh workflows

Summary Reliable mesh‐based simulations are needed to solve complex engineering problems. Mesh adaptivity can increase reliability by reducing discretization errors but requires multiple software components to exchange information. Often, components exchange information by reading and writing a common file format. This file‐based approach becomes a problem on massively parallel computers where filesystem bandwidth is a critical performance bottleneck. Our approach using data streams and component interfaces avoids the filesystem bottleneck. In this paper, we present these techniques and their use for coupling mesh adaptivity to the PHASTA computational fluid dynamics solver, the Albany multi‐physics framework, and the Omega3P linear accelerator frequency analysis applications. Performance results are reported on up to 16,384 cores of an Intel Knights Landing‐based system.

Smith, Cameron W.↗

aphBO-2GP-3B: a budgeted asynchronous parallel multi-acquisition functions for constrained Bayesian optimization on high-performing computing architecture

High-fidelity complex engineering simulations are often predictive, but also computationally expensive and often require substantial computational efforts. The mitigation of computational burden is usually enabled through parallelism in high-performance cluster (HPC) architecture. Optimization problems associated with these applications is a challenging problem due to the high computational cost of the high-fidelity simulations. In this paper, an asynchronous parallel constrained Bayesian optimization method is proposed to efficiently solve the computationally expensive simulation-based optimization problems on the HPC platform, with a budgeted computational resource, where the maximum number of simulations is a constant. The advantage of this method are three-fold. Firstly, the efficiency of the Bayesian optimization is improved, where multiple input locations are evaluated parallel in an asynchronous manner to accelerate the optimization convergence with respect to physical runtime. This efficiency feature is further improved so that when each of the inputs is finished, another input is queried without waiting for the whole batch to complete. Second, the proposed method can handle both known and unknown constraints. Third, the proposed method samples several acquisition functions based on their rewards using a modified GP-Hedge scheme. The proposed framework is termed aphBO-2GP-3B, which means asynchronous parallel hedge Bayesian optimization with two Gaussian processes and three batches. The numerical performance of the proposed framework aphBO-2GP-3B is comprehensively benchmarked using 16 numerical examples, compared against other 6 parallel Bayesian optimization variants and 1 parallel Monte Carlo as a baseline, and demonstrated using two real-world high-fidelity expensive industrial applications. The first engineering application is based on finite element analysis (FEA) and the second one is based on computational fluid dynamics (CFD) simulations.

97 MATHEMATICS AND COMPUTING↗

First-order finite-Larmor-radius fluid modeling of tearing and relaxation in a plasma pinch

Drift and Hall effects on magnetic tearing, island evolution, and relaxation in pinch configurations are investigated using a non-reduced first-order finite-Larmor-radius (FLR) fluid model with the nonideal magnetohydrodynamics (MHD) with rotation, open discussion (NIMROD) code [C.R. Sovinec and J. R. King, J. Comput. Phys. 229, 5803 (2010)]. An unexpected result with a uniform pressure profile is a drift effect that reduces the growth rate when the ion sound gyroradius ({rho}{sub s}) is smaller than the tearing-layer width. This drift is present only with warm-ion FLR modeling, and analytics show that it arises from {nabla}B and poloidal curvature represented in the Braginskii gyroviscous stress. Nonlinear single-helicity computations with experimentally relevant {rho}{sub s} values show that the warm-ion gyroviscous effects reduce saturated-island widths. Computations with multiple nonlinearly interacting tearing fluctuations find that m = 1 core-resonant-fluctuation amplitudes are reduced by a factor of two relative to single-fluid modeling by the warm-ion effects. These reduced core-resonant-fluctuation amplitudes compare favorably to edge coil measurements in the Madison Symmetric Torus (MST) reversed-field pinch [R. N. Dexter et al., Fusion Technol. 19, 131 (1991)]. The computations demonstrate that fluctuations induce both MHD- and Hall-dynamo emfs during relaxation events. The presence of a Hall-dynamo emf implies a fluctuation-induced Maxwell stress, and the simulation results show net transport of parallel momentum. The computed magnitude of force densities from the Maxwell and competing Reynolds stresses, and changes in the parallel flow profile, are qualitatively and semi-quantitatively similar to measurements during relaxation in MST.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nonlinear fluid simulation of particle and heat fluxes during burst of ELMs on DIII-D with BOUT++ code [Fluid Simulation of Particle and Heat Fluxes during Burst of ELMs on DIID with BOUT++ code]

In order to study the distribution and evolution of the transient particle and heat fluxes during edge-localized mode (ELM) bursts, a BOUT++ six-field two-fluid model based on the Braginskii equations with non-ideal physics effects is used to simulate pedestal collapse in divertor geometry. We used the profiles from the DIII-D H-mode discharge #144382 with fast target heat flux measurements as the initial conditions for the simulations. Moreover, a flux-limited parallel thermal conduction is used with three values of the flux-limiting coefficient ${{\alpha}_{j}}$ , free streaming model with ${{\alpha}_{j}}=1$ , sheath-limit with ${{\alpha}_{j}}=0.05$ , and one value in between. The studies show that a 20 times increase in ${{\alpha}_{j}}$ leads to ~6 times increase in the heat flux amplitude to both the inner and outer targets, and the widths of the fluxes are also expanded. The sheath-limit model of flux-limiting coefficient is found to be the most appropriate one, which shows ELM sizes close to the measurements. The evolution of the density profile during the burst of ELMs of DIII-D discharge #144382 is simulated, and the collapse in width and depth of ${{n}_{\text{e}}}$ are reproduced at different time steps. The growing process of the profiles for the heat flux at divertor targets during the burst of ELMs measured by IRTV (infrared television) is also reproduced by this model. The widths of heat fluxes towards targets are a little narrower, and the peak amplitudes are twice the measurements possibly due to the lack of a model of divertor radiation which can effectively reduce the heat fluxes. The magnetic flutter combined with parallel thermal conduction is found to be able to increase the total heat loss by around 33% since the magnetic flutter terms provide the additional conductive heat transport in the radial direction. Finally, the heat flux profile at both the inner and outer targets is obviously broadened by magnetic flutter. The lobe structures near the X-point at LFS are both broadened and elongated due to the magnetic flutter.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

MOOSE ProbML: Parallelized probabilistic machine learning and uncertainty quantification for computational energy applications

Here, this paper presents the development and demonstration of massively parallel probabilistic machine learning (ML) and uncertainty quantification (UQ) capabilities within the Multiphysics Object-Oriented Simulation Environment (MOOSE), an open-source computational platform for parallel finite element and finite volume analyses. In addressing the computational expense and uncertainties inherent in complex multiphysics simulations, this paper integrates Gaussian process (GP) variants, active learning, Bayesian inverse UQ, adaptive forward UQ, Bayesian optimization, evolutionary optimization, and Markov chain Monte Carlo (MCMC) within MOOSE. It also elaborates on the interaction among key MOOSE systems — Sampler, MultiApp, Reporter, and Surrogate — in enabling these capabilities. The modularity offered by these systems enables development of a multitude of probabilistic ML and UQ algorithms in MOOSE. Example code demonstrations include parallel active learning and parallel Bayesian inference via active learning. The impact of these developments is illustrated through five applications relevant to computational energy applications: UQ of nuclear fuel fission product release, using parallel active learning Bayesian inference; very rare events analysis in nuclear microreactors using active learning; advanced manufacturing process modeling using multi-output GPs (MOGPs) and dimensionality reduction; fluid flow using deep GPs (DGPs); and tritium transport model parameter optimization for fusion energy, using batch Bayesian optimization. These capabilities are part of the MOOSE framework.

97 - MATHEMATICS AND COMPUTING↗

Multi-jagged: A scalable parallel spatial partitioning algorithm

Geometric partitioning is fast and effective for load-balancing dynamic applications, particularly those requiring geometric locality of data (particle methods, crash simulations). We present, to our knowledge, the first parallel implementation of a multidimensional-jagged geometric partitioner. In contrast to the traditional recursive coordinate bisection algorithm (RCB), which recursively bisects subdomains perpendicular to their longest dimension until the desired number of parts is obtained, our algorithm does recursive multi-section with a given number of parts in each dimension. By computing multiple cut lines concurrently and intelligently deciding when to migrate data while computing the partition, we minimize data movement compared to efficient implementations of recursive bisection. We demonstrate the algorithm's scalability and quality relative to the RCB implementation in Zoltan on both real and synthetic datasets. Our experiments show that the proposed algorithm performs and scales better than RCB in terms of run-time without degrading the load balance. Lastly, our implementation partitions 24 billion points into 65,536 parts within a few seconds and exhibits near perfect weak scaling up to 6K cores.

97 MATHEMATICS AND COMPUTING↗

Mechanisms of heat flux across the Southern Greenland continental shelf in 1/10° and 1/12° ocean/sea ice simulations

The increased presence of warm Atlantic water on the Greenland continental shelf has been connected to the accelerated melting of the Greenland Ice Sheet, particularly in the southwest and southeast shelf regions. Results from two high-resolution coupled ocean-sea ice simulations that utilized either the 1/10-degree Parallel Ocean Program (POP) or the 1/12-degree HYbrid Coordinate Ocean Model (HYCOM) are used to understand the flux of heat on and off the southern Greenland shelf. The analysis reveals that the region of greatest heat flux onto the shelf is southeast Greenland. On the southwestern shelf, heat is mainly exported from the shelf to the interior basins. We identify differences in the shelf break current structure and on-shelf heat content between the two simulations. Just south of the Denmark strait, there is a seasonally persistent pattern of multi-day variability in the cross-shelf heat flux in both simulations. In the POP simulation, this high-frequency signal results in net on-shore heat flux. In the HYCOM simulation, the signal is weaker and results in net off-shelf heat flux. This variability is consistent with Denmark Strait Overflow eddies traveling along the shelf break.

58 GEOSCIENCES↗

Yearly report for the period Jan. 2018 – Feb. 2019 IC Project: w17_faultprediction “Critical Stress in Earth”

The consequence of earthquake is usually catastrophic. Currently, we cannot determine when a fault is approaching failure due to either anthropogenic activities or tectonic movement. In an anthropogenically perturbed setting, the rate of physical changes on faults far exceeds most natural processes with currently unpredictable and unmeasurable results. In a tectonic setting we generally do not know where a fault is in the earthquake cycle beyond noting how long has passed since the last rupture, which is itself sometimes unknown. The Laboratory has therefore funded a multi million multi-year LDRD-DR program that comprises experiments, numerical modeling, and machine learning in order to develop and test a highly novel approach to probe the earthquake cycle and in particular, to detect and locate stressed faults that are approaching failure. For this program, modeling of a series of sheared granular layers undergoing stick-slip behavior using the EES-17’s Combined Finite-Discrete Element Method (FDEM) based code HOSS (Hybrid Optimization Software Suite) plays a pivotal role since numerical simulations of granular fault gouge allow for analysis of the mechanical behavior of the system at a level of spatial and temporal resolution not accessible experimentally, and also offer the possibility of identifying the most important parameters governing earthquake dynamics. The simulated data also provide very detailed stress, strain and motion information for machine learning purpose to predict earthquake. The code – HOSS – has been developed in Geophysics Group in LANL during the past ten years and is used to simulate the stick-slip behavior of granular fault gouge. One of the key feature of HOSS is that it is superior to pure finite element method and discrete element method and can provide very detailed evolvement information of granular fault gouge. Additionally, its parallel computing capability makes large scale earthquake gouge simulation possible. Taking these facts into account, and also because few other fully parallel FDEM code exists, this IC project allows LANL to stay at the forefront of earthquake gouge and granular material simulation in the world.

42 ENGINEERING↗

Analysis and Visualization of Multi-Scale Astrophysical Simulations using Python and NumPy

The study the origins of cosmic structure requires large-scale computer simulations beginning with well-constrained, observationally-determined, initial conditions. We use Adaptive Mesh Refinement to conduct multi-resolution simulations spanning twelve orders of magnitude in spatial dimensions and over twenty orders of magnitude in density. These simulations must be analyzed and visualized in a manner that is fast, accurate, and reproducible. I present 'yt,' a cross-platform analysis toolkit written in Python. 'yt' consists of a data-management layer for transporting and tracking simulation outputs, a plotting layer, a parallel analysis layer for handling mesh-based and particle-based data, as well as several interfaces. I demonstrate how the origins of cosmic structure--from the scale of clusters of galaxies down to the formation of individual stars--can be analyzed and visualized using a NumPy-based toolkit. Additionally, I discuss efforts to port this analysis code to other adaptive mesh refinement data formats, enabling direct comparison of data between research groups using different methods to simulate the same objects.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DFT modeling of adsorption onto uranium metal using large-scale parallel computing

There is a dearth of atomistic simulations involving the surface chemistry of 7-uranium which is of interest as the key fuel component of a breeder-burner stage in future fuel cycles. Recent availability of high-performance computing hardware and software has rendered extended quantum chemical surface simulations involving actinides feasible. With that motivation, data for bulk and surface 7-phase uranium metal are calculated in the plane-wave pseudopotential density functional theory method. Chemisorption of atomic hydrogen and oxygen on several un-relaxed low-index faces of 7-uranium is considered. The optimal adsorption sites (calculated cohesive energies) on the (100), (110), and (111) faces are found to be the one-coordinated top site (8.8 eV), four-coordinated center site (9.9 eV), and one-coordinated top 1 site (7.9 eV) respectively, for oxygen; and the four-coordinated center site (2.7 eV), four-coordinated center site (3.1 eV), and three-coordinated top2 site (3.2 eV) for hydrogen. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗