Search NASA⌕ Search

SEARCH · Search NASA

Results for “processing parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Chromatographic Modeling of 1-Foot Detritiation Test Column Results for the Optimization of Regeneration Time

This report documents the methods and results of a modeling study on a series of data generated by 1-foot test columns for the Water Detritiation project. In order to compliment modeling work already in progress on this project, a purely empirical curve-fitting approach is used in this study to determine chromatographic performance indicators such as retention time, curve width, and the number of chromatographic stages. The data used in this study comes from four sets of chromatographic test separations performed in March through May of 2017 using 1-foot columns. All are using the same flow rates and temperature (room temperature, nominally 25 C°). The first set of data (referred to in this report as the Column 1 data) is a series of twelve breakthrough curve measurements. Prior to each of these twelve runs, the column was regenerated by flowing hydrogen gas through the column, for increasing amounts of time, ranging from 2 hours to 25 hours. The second set of data (referred to as the Column 2 data) is comprised of five measurements of breakthrough curves measured in similar fashion as the Column 1 data, across a range of regeneration times from 2 to 21 hours. The third set of data (referred to as the Purge data) is of three breakthrough curves, measured after a regeneration time of 8 hours, which takes place after a nitrogen purge of 15, 30, or 45 minutes. The fourth data set is a series of five breakthrough curve measurements using a 2 nd batch of stationary phase, taken after regeneration times ranging from 2 to 20 hours. The overall modeling approach is as follows. First, the data is pre-processed for formatting, artifact removal, and is normalized. The data is then fit by integrated versions of four common chromatographic models. The best model is chosen based on the predictive performance of the model, and chromatographic performance values are calculated based on the best model’s fit parameters. Each of these processes are detailed below.

42 ENGINEERING↗
DOE OSTI2026

Physiological Controls on Carbon Fluxes and Biomass Production in Miscanthus: Insights From a Process‐Based Agroecosystem Model

Biomass crops serve as essential feedstocks for renewable energy and bioproducts and play a critical role in achieving lower emissions in the transportation sector. However, dedicated perennial biomass crops such as Miscanthus × giganteus (Miscanthus) remain underrepresented in process-based agroecosystem models, limiting robust evaluation of their economic and environmental performance. In this study, we developed a data-constrained representation of the sterile triploid Miscanthus (IL clone) within the process-based model ecosys, integrating global sensitivity analysis, ensemble simulation, and parameter calibration. Planting, harvesting, and fertilization practices consistent with field management were incorporated, and phenology was constrained using PhenoCam-derived Green Chromatic Coordinate (GCC) data. Using the Morris global sensitivity analysis method, we identified 11 key physiological parameters governing plant carbon, water, and nutrient relations, particularly processes associated with CO 2 assimilation. We then conducted ensemble simulations by perturbing these parameters and calibrated the model against eddy covariance fluxes and field-measured biomass. Building on the calibrated operating state, parameter-response analyses show that different photosynthetic processes influence productivity in different ways. Protein allocation determines whether productivity increases toward a higher level, whereas electron transport capacity controls additional gains once protein allocation approaches saturation. These findings demonstrate that parameter importance depends on physiological context and on which photosynthetic processes remain limiting. Calibration and validation against observations show that ecosys can reliably reproduce carbon and water fluxes, as well as both above- and belowground biomass, with post-calibration GPP R 2 improving from 0.67 to 0.95 during the calibration period and remaining high during validation (R 2 = 0.95). These results provide a mechanistic foundation for regional simulations and sustainable bioenergy assessments.

ecosys↗
DOE OSTI2023

On the 3D printing of polypropylene and post-processing optimization of thermomechanical properties

Polypropylene (PP) is a highly desirable polyolefin in various plastic industries due to its outstanding thermomechanical properties and chemical resistance. Therefore, the 3D printing of PP is an interesting avenue to explore in digitized manufacturing, where more freedom in structural designs is available for new and extended applications, such as high-performance engineering parts. Here, in this work, we 3D printed PP and studied the effect of printing parameters and post-processing conditions on the printed polymer’s thermomechanical behavior. Results showed that nozzle and bed temperatures of 220 and 100°C produced a high printing quality. Infill percentages between 80 and 90%, coupled with a 4-h annealing at 110ºC, also resulted in optimal printed properties. It is thought that PP can be potentially blended with polyethylene or other vinyl polymers for a more extended 3D printing utility and practical applications in rapid tooling and prototyping.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Multilevel Analysis of Electrochemically Mediated Methanolysis of Poly(ethylene terephthalate) (PET)

Here, this study presents a multilevel analysis of electrochemically mediated methanolysis as a promising method for reducing the environmental impacts of plastic recycling, with a focus on depolymerizing poly(ethylene terephthalate) (PET) into dimethyl terephthalate (DMT). Instead of conventional chemical PET depolymerization, this electrochemical approach provides distinct technical advantages in process control and efficiency. At the process level, key operational parameters, including applied current and reaction time, were systematically investigated to optimize PET conversion and DMT selectivity. The electrochemical approach was directly compared to equivalent chemical methanolysis systems and demonstrated superior performance in terms of PET conversion and DMT selectivity. Building on these findings, a technoeconomic assessment identified the current economic bottlenecks and revealed that improvements in process design, DMT selectivity, PET conversion, and energy efficiency are key to reducing the overall process cost and enabling future implementation. While further optimization is required for market competitiveness, these results establish a performance baseline for the electrochemically mediated PET methanolysis process and underscore the importance of combining process-level innovation with systems-level evaluation in the development of sustainable recycling technologies.

chemical recycling↗
DOE OSTI2018

Characterization of Uranium Ore Concentrate Chemical Composition via Raman Spectroscopy

Uranium Ore Concentrate (UOC, often called yellowcake) is a generic term that describes the initial product resulting from the mining and subsequent milling of uranium ores en route to production of the U-compounds used in the fuel cycle. Depending on the mine, the ore, the chemical process, and the treatment parameters, UOC composition can vary greatly. With the recent advent of handheld spectrometers, we have chosen to investigate whether either commercial off-the-shelf (COTS) handheld devices or laboratory-grade Raman instruments might be able to i) identify UOC materials, and ii) differentiate UOC samples based on chemical composition and thus suggest the mining or milling process. Twenty-eight UOC samples were analyzed via FT-Raman spectroscopy using both 1064 nm and 785 nm excitation wavelengths. These data were also compared with results from a newly developed handheld COTS Raman spectrometer using a technique that lowers background fluorescence signal. Initial chemometric analysis was able to differentiate UOC samples based on mine location. Additional compositional information was obtained from the samples by performing XRD analysis on a subset of samples. The compositional information was integrated with chemometric analysis of the spectroscopic dataset allowing confirmation that class identification is possible based on compositional differences between the UOC samples, typically involving species such as U3O8, α-UO2(OH)2, UO4•2H2O (metastudtite), K(UO2)2O3, etc. While there are clearly excitation λ sensitivities, especially for dark samples, Raman analysis coupled with chemometric data treatment can nicely differentiate UOC samples based on composition and even mine origin.

Su, Yin-Fong↗
DOE OSTI2021

Exfoliation of surfactant swollen layered MWW zeolites into two-dimensional zeolite nanosheets using telechelic liquid polybutadiene

We report two-dimensional (2D) zeolites have the potential to enhance mass transport by reducing diffusion lengths and thus find applications in catalysis and separation. High aspect ratio 2D zeolite nanosheets are required for fabrication of thin, high-flux zeolite membranes. Preparation of 2D zeolite nanosheets can be achieved by exfoliation of layered zeolite precursors, which usually requires multiple steps including swelling with cationic surfactants, exfoliation by applying a mechanical force such as shearing or sonication, purification and removal of the surfactants. The exfoliation of surfactant swollen layered zeolite precursors has been studied using molten polystyrene and telechelic liquid polybutadiene, but still requires extensive shearing force. Recently, a novel one-step exfoliation method has been developed for nonswollen MWW zeolite precursors using tetrabutylammonium hydroxide (TBAOH) solution. In this work, we study the exfoliation of surfactant swollen MWW layered precursors (with and without aluminum) in commercially available liquid hydroxyl-terminated polybutadiene (HTPB) with the aim to provide fundamental understanding of the interaction between the liquid polybutadiene and the surfactant swollen layered zeolite precursors. It was found that surfactant swollen ITQ-1, (ITQ-1(S)), a pure silica layered precursor with MWW framework after being swollen with a cationic surfactant, can be exfoliated in liquid HTPB at room temperature without applying any additional shearing force. The aluminum containing surfactant swollen MWW precursors can be also exfoliated in HTPB at room temperature, but require additional shearing forces. The exfoliation process was monitored using rheology experiments and studied by tuning the composition of the zeolite precursors. The interaction between the layered zeolite precursor and the hydroxyl group of the liquid polybutadiene allows the polymer to intercalate the precursor and exfoliate it into nanosheets. The presence of framework aluminum and the nature of the organic structure directing agents (OSDAs) are key parameters affecting the exfoliation process. Framework Al is unfavorable for the exfoliation possibly due to the surface charges introduced by the aluminum. Bulky OSDA, trimethyladamantammonium (TMAda + ), in the interlayer spacing may facilitate the exfoliation.

2D nanosheets↗
DOE OSTI2018

Rare behavior of growth processes via umbrella sampling of trajectories

We compute probability distributions of trajectory observables for reversible and irreversible growth processes. These results reveal a correspondence between reversible and irreversible processes, at particular points in parameter space, in terms of their typical and atypical trajectories. Thus key features of growth processes can be insensitive to the precise form of the rate constants used to generate them, recalling the insensitivity to microscopic details of certain equilibrium behavior. We obtained these results using a sampling method, inspired by the "s-ensemble" large-deviation formalism, that amounts to umbrella sampling in trajectory space. The method is a simple variant of existing approaches, and applies to ensembles of trajectories controlled by the total number of events. It can be used to determine large-deviation rate functions for trajectory observables in or out of equilibrium.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2021

Process Robustness of Friction Stir Dovetailing of AA7099 to Steel with In Situ AA6061 Interlayer Linking

Rolled homogeneous armor (RHA) steel was joined to aluminum alloy AA7099-T7451 with an interlayer of AA6061-T651 by single-pass friction stir dovetailing (FSD). The evolution of the AA7099/AA6061 and AA6061/steel interfacial microstructures and mechanical properties of the joints were examined. The AA6061 interlayer prevented Zn migration from the AA7099 to the steel during FSD and inhibited formation of brittle, Zn-rich, Fe-Al intermetallic compounds within the joint. The flow of the dissimilar aluminum alloys at the interface was controlled with a partially threaded friction stir welding pin and a dovetail geometric configuration optimized in previous work. The process robustness was explored to establish parameter windows by elucidating parametric effects on the relationship between process conditions and the joint’s microstructure and mechanical properties. Ranges of process forge force (50–70 kN) and interface temperature (475°C–515°C) consistently yielded joints with adequate performance. The load-carrying capacity in lap shear tensile tests was 2025 ? 100 N/mm.

Friction Stir Dovetailing, FSW, AA7099, AA6061, Ro↗
DOE OSTI2024

Effects of boundary hydraulics, dissolved oxygen, and dissolved organic carbon on growth and death dynamics of aerobic microbes in riverbed dune-induced hyporheic zones

Surface and groundwater interact in the hyporheic zone beneath and adjacent to rivers in the presence of a diverse microbial community. Heterotrophic bacteria mediate a range of environmentally important reactions, yet few studies have quantified bacterial growth and death dynamics in the hyporheic zone, and none have systematically analyzed their response to variations in hydraulic or chemical conditions. Here we used MODFLOW and SEAM3D to simulate hydraulics; dissolved oxygen (DO) and dissolved organic carbon (DOC) transport; and aerobic microbial metabolism, growth, and death in hyporheic zones induced by riverbed dunes. We ran simulations both with and without growth/death processes, and varied hydraulic parameters and DO/DOC boundary concentrations. Microbial biomass reached steady state (t = 3 days) in every simulation, at which time there was greater biomass and DOC biodegradation rates in the hyporheic flowcell (300% and 85% higher for the base case, respectively) when accounting for microbial growth dynamics. This occurred as microbial biomass tailored its spatial distribution to the availability of DO and DOC, demonstrating the importance of simulating growth/death processes. Biomass generally increased with hyporheic flow cell area as upwelling groundwater decreased. When varying surface water DO and DOC source concentrations relative to the base case, the greatest effect on biomass occurred when increasing DOC and decreasing DO. We determined minimum DO and DOC steady-state concentrations required for microbial growth, but the minimums were not absolute or related by stoichiometry. Increasing DOC created a smaller area of microbes with higher concentrations relative to the base case. Increasing DO slightly increased the area occupied by microbes while keeping the total biomass nearly constant. Overall, microbial growth and death dynamics depend on DO and DOC availability in the hyporheic zone, which is dependent on DOC/DO boundary concentrations and hyporheic flow paths, and in turn the hydraulic interaction between surface water and groundwater.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2018

Selective Epitaxial Growth of III–N Structures Using Ion-Beam Nanolithography

The selective epitaxial growth of GaN by metalorganic vapor-phase epitaxy combined with ion-beam etching is investigated. To this end, partially masked GaN epitaxial layers are fabricated by depositing a thin Si{sub 3}N{sub 4} layer onto the surface in a single technological process with the growth of GaN and the subsequent opening of windows of different shapes in this layer by an ion beam. Selective epitaxial growth regimes are studied. It is shown that, in a situation where the total area of the windows in the mask is small relative to the total area of the sample, the required epitaxy duration should be 5–10 s, which impairs the reproducibility of the parameters of the epitaxial process. It is also shown that the mechanism of the selective growth of submicrometer objects differs significantly from that for planar layers and selectively grown layers with dimensions of ~1 μm or greater. The effect of precursor (trimethylgallium and ammonia) fluxes on the character of selective epitaxy is examined. To investigate the possibilities of varying mask topology for fabricating model objects with regard to photonic crystals, the impact of the shape and orientation of the windows in the Si{sub 3}N{sub 4} mask on the character of selective epitaxy is studied.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Guidance for Developing Digital Twins for Online Condition Monitoring of Nuclear Power Plant Components

Online condition monitoring is an area of active research that may enable optimized scheduling, maintenance, and safety of nuclear power plant components, reducing unnecessary derates while simultaneously improving operational capacity. Digital twins (DTs) are one avenue to conduct online condition monitoring and are currently being explored by national laboratories and universities alike. DTs for online condition monitoring are, in essence, state concurrent models that emulate a physical process which predicts a parameter and compares it against a measured value. The promise of DT is that they may provide additional insights by combining and interpreting various sources of information and may be used for preventative maintenance scheduling optimization or early fault detection. DTs for condition monitoring are projected to be valuable for meeting requirements under 10 CFR 50.55a and 10 CFR 50.65. However, DT technologies are still under significant development and the process for developing a DT for condition monitoring has not been formalized. Therefore, in this work, we present an initial framework for developing a DT, discuss and review the various challenges and considerations for DT deployment, and identify the opportunities that a DT can improve. Here, the presented framework is intended to help developers formulate a strategy when approaching DT development for condition monitoring. A DT use case for a reactor coolant pump is presented to demonstrate the proposed framework.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Adsorption Thermodynamics for Process Simulation

Adsorption has rapidly evolved in recent decades and is an established separation technology extensively practiced in gas separation industries and others. However, rigorous thermodynamic modeling of multicomponent adsorption equilibrium remains elusive, and industrial practitioners rely heavily on expensive and time-consuming trial-and-error pilot studies to develop adsorption units. Here, this article highlights the need for rigorous adsorption thermodynamic models and the limitations and deficiencies of existing models such as the extended Langmuir isotherm, dual-process Langmuir isotherm, and adsorbed solution theory. It further presents a series of recent advances in the generalization of the classical Langmuir isotherm of single-component adsorption by deriving an activity coefficient model to account for the adsorbed phase adsorbate–adsorbent interactions, substituting adsorbed phase adsorbate and vacant site concentrations with activities, and extending to multicomponent competitive adsorption equilibrium, both monolayer and multilayer. Requiring a minimum set of physically meaningful model parameters, the generalized Langmuir isotherm for monolayer adsorption and the generalized Brunauer–Emmett–Teller isotherm for multilayer adsorption address various thermodynamic modeling challenges including adsorbent surface heterogeneity, isosteric enthalpies of adsorption, BET surface areas, adsorbed phase nonideality, adsorption azeotrope formation, and multilayer adsorption. Also discussed is the importance of quality adsorption data that cover sufficient temperature, pressure, and composition ranges for reliable determination of the model parameters to support adsorption process simulation, design, and optimization.

09 BIOMASS FUELS↗
DOE OSTI2024

Elucidating the Radiation-Induced Redox Chemistry of Plutonium Under Used Nuclear Fuel Reprocessing Conditions

Plutonium plays a critical role in the development of sustainable nuclear fuel cycles, and yet, our fundamental understanding of this element’s inherent radiation-induced redox chemistry and associated impacts on nuclear fuel cycle technologies is limited. Unanticipated changes in oxidation state distribution can influence the speciation and transport of plutonium in a given process. Control of these parameters is especially important for used nuclear fuel reprocessing technologies, wherein the separation and recovery of plutonium is typically achieved by the selective formation, maintenance, and complexation of specific oxidation states. Furthermore, plutonium’s inherent radiation-induced redox chemistry has the capacity to influence the radiolytic behavior of its complexes, the longevity of which are critical in the design of efficient and cost-effective advanced reprocessing technologies. These radiation-induced processes are unavoidable under fuel cycle conditions owing to the inherency of ionizing radiation fields to the decay of plutonium’s isotopes and to the various other radioisotopes generated by nuclear fission and neutron-capture process and the subsequent radioactive decay of their products. As such, mechanistically understanding the response of plutonium’s multiple oxidation states to multi-component ionizing radiation fields is essential for predicting the behavior of this critical element under used nuclear fuel reprocessing conditions. Here, through a combination of time-resolved (electron pulse) and steady-state (alpha and gamma) irradiation experiments complemented by quantitative, multiscale modeling calculations, we present advances in our understanding of radiation-induced plutonium redox chemistry!

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

U.S. Nuclear Operating Experience Program for Probabilistic Risk Assessment Parameter Estimations

This presentation describes the overall process of the U.S. Nuclear Regulatory Commission (NRC)operating experience (OpE) program to estimate probabilistic risk assessment parameters, the estimations of initiating event frequencies, the component unreliability, and the quality assurance and quality control activities for the OpE program. This presentation can be used for training, workshop, or knowledge transfer purpose.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Digital-Twin-Enabling Technologies for Online Condition Monitoring of Nuclear Power Plant Components

Online condition monitoring is an area of active research that may enable optimized scheduling, maintenance, and safety of nuclear power plant components, reducing unnecessary derates while simultaneously improving operational capacity. Digital twins (DTs) are one avenue to conduct online condition monitoring and are currently being explored by national laboratories and universities alike. DTs for online condition monitoring are, in essence, state concurrent models that emulate a physical process which predicts a parameter and compares it against a measured value. A DT’s goal is to provide additional insights by combining and interpreting various sources of information for preventative maintenance scheduling optimization or early fault detection. DTs for condition monitoring are projected to be valuable for meeting requirements under 10 CFR 50.55a, “Codes and Standards,” and 10 CFR 50.65, “Requirements for Monitoring the Effectiveness of Maintenance at Nuclear Power Plants”. However, DT technologies are still under significant development, and the process for developing a DT for condition monitoring has not been formalized. Therefore, in this work, we present an initial framework for developing a DT, discuss and review the various challenges and considerations for DT deployment, and identify the opportunities that a DT can improve. The presented framework is intended to help developers formulate a strategy when approaching DT development for condition monitoring. In conclusion, a DT use case for a reactor coolant pump is presented to demonstrate the proposed framework.

advanced sensor instrumentation↗
DOE OSTI2025

A Robust Data-Driven Approach for Mechanical Serial Sectioning

Mechanical serial sectioning (MSS) provides detailed microstructural information across large length scales. By repeatedly removing thin layers of material and imaging the exposed surface, a 3D representation of a specimen’s internal structure can be constructed, enabling failure analysis and feature identification that are otherwise inaccessible via conventional 2D or nondestructive evaluation techniques. Achieving consistent and accurate material removal can be challenging due to system variability, requiring an experienced operator to manually adjust parameters, prolonging data collection times and necessitating post-processing routines to standardize the data. Here, to address these challenges, this paper presents the employment of a one-step model predictive control (MPC) framework tailored to a run-to-run (R2R) controller. The R2R-MPC controller automates the parameter selection process, improving the consistency of material removal through iterative feedback for disturbance rejection and accurate tracking of the target removal rate. Using a data-driven approach, the controller robustly adapts to changing material characteristics. The effectiveness of the R2R-MPC controller is demonstrated through simulation and experimental results and compared to previous data collection procedures.

3D Materials Science↗
DOE OSTI2021

Engineering Scale Drying of Aluminum-Clad Spent Nuclear Fuel: Experiment Report

Engineering-scale tests were performed to evaluate the relative effectiveness of forced gas and vacuum-drying processes on aluminum-clad spent nuclear fuel (ASNF) in preparation for extended dry storage. Drying models were developed to improve confidence in the likely range of conditions at the start of dry storage and to understand the factors most significant to each process. Testing was performed at the Holtec International Forced Helium Dehydration training facility in Camden, New Jersey, by students from the University of South Carolina in collaboration with Idaho National Laboratory. A full-size Type 1a basket, with a full-diameter vessel configuration (based on the Department of Energy standardized canister design), was used in combination with a 10 assembly surrogate ASNF arrangement to provide a proxy for geometry. A resistance heater incorporated in one assembly simulated the influence of 100 W decay heat. This instrumented chamber allowed testing of the removal of bulk water, physisorbed water, and chemisorbed water over a range of operating parameters with either drying process. Thick oxide films were grown on aluminum test plates to mimic the ASNF surface chemistry. These one-use test plates were housed within select assemblies during drying. Post-test analysis of these plates gave a measure of the moisture removed during each test, which was compared to a control. Instrumentation provided detailed thermal, humidity, and gas or pressure data relevant to each test. Model simulations generally compared favorably to instrument data for the tests. While both processes were able to remove bulk water, removal of chemisorbed water was shown to depend heavily on local temperature. To the disadvantage of vacuum drying, operations approaching or exceeding 220°C achieved consistently more dehydroxylation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

First-Principles Modeling of the Repassivation of Corrosion Resistant Alloys: Part I. O and Cl Adsorption Energy

To understand the mechanism of repassivation, a key process that controls the performance of corrosion resistant alloys (CRAs), it is useful to obtain some fundamental parameters that describe the atomistic processes. Oxygen and chlorine adsorption energies were systematically calculated with density functional theory for Ni-22Cr alloys with seven different solute elements: Co, Cu, Fe, Mn, Mo, Ru and W. All elements other than Cu enhance both O and Cl adsorption to alloy surfaces. Cr has the strongest effect among these elements. Surface configurations that give stronger O adsorption also tend to give stronger Cl adsorption. While this makes it difficult to differentiate the effect of these solute elements on the oxidation/repassivation tendency of alloys, these fundamental properties provide the foundation for higher scale models that could be used to study the oxidation process during corrosion and potentially inform the design of CRAs. Bader charge analysis reveals a strong relationship between the adatom adsorption energy and the Bader charges of both O and Cl adatom. In conclusion, the work function of alloy surfaces is increased by O while decreased by Cl, suggesting that Cl adsorption can have an intrinsic negative impact on corrosion resistance by decreasing the barrier to electron transfer.

36 MATERIALS SCIENCE↗