Search NASA⌕ Search

SEARCH · Search NASA

Results for “program costs”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Mobile data buoy system

The Mobile Data Buoy System was conceived to serve the users requirement for obtaining water quality parameters from two separate watershed systems. In view of the cost constraints of the ERTS program it was obvious that the network of 10 sampling stations required could not be of the fixed installation type; therefore, it was decided to go to a system of battery powered buoys of a size that could be used in one watershed system for a period of time and then moved to another by use of a relatively small 6.7 m (22 foot) boat. The basic idea of the water quality measurement program was to establish the water quality pattern of change from the headwaters of the watersheds to and through the Mobile Bay. This would allow the investigator to develop a good picture of the state's major water resources and the pressures from pollution that are being imposed. At this point in deployment of this mobile system of buoys, it is too early to put a quantitative value on the system, however it appears less expensive than known fixed installations as to first cost. It has a basic advantage in that it can be moved, at very little expense, to alternate sites where it is desired to obtain water quality data. It is to be noted this buoy system which covers a 80 Km (50 mile) stretch of the Black Warrior River and then skips down 483 Km (300 miles) to Mobile Bay for the next measurements would not be feasible unless there is a satellite to collect and relay the data.

Morton, R. A.↗
NASA NTRS2015

Small Habitat Commonality Reduces Cost for Human Mars Missions

Most view the Apollo Program as expensive. It was. But, a human mission to Mars will be orders of magnitude more difficult and costly. Recently, NASA's Evolvable Mars Campaign (EMC) mapped out a step-wise approach for exploring Mars and the Mars-moon system. It is early in the planning process but because approximately 80% of the total life cycle cost is committed during preliminary design, there is an effort to emphasize cost reduction methods up front. Amongst the options, commonality across small habitat elements shows promise for consolidating the high bow-wave costs of Design, Development, Test and Evaluation (DDT&E) while still accommodating each end-item's functionality. In addition to DDT&E, there are other cost and operations benefits to commonality such as reduced logistics, simplified infrastructure integration and with inter-operability, improved safety and simplified training. These benefits are not without a cost. Some habitats are sub-optimized giving up unique attributes for the benefit of the overall architecture and because the first item sets the course for those to follow, rapidly developing technology may be excluded. The small habitats within the EMC include the pressurized crew cabins for the ascent vehicle,

Griffin, Brand N.↗
NASA NTRS1978

SPS cost considerations

Recent solar power satellite (SPS) system definition studies have emphasized cost estimation for the operational phase of an SPS program, in order to assess economic practicality of SPS. A cost analysis approach is described. Cost results for a silicon photovoltaic SPS are reported, showing SPS costs from $1700 to $2700 per kilowatt and busbar power costs from 3 cents to 7 cents per kilowatt-hour. Rationales behind the estimates are discussed.

Woodcock, G. R.↗
NASA NTRS1993

Neural-network dedicated processor for solving competitive assignment problems

A neural-network processor for solving first-order competitive assignment problems consists of a matrix of N x M processing units, each of which corresponds to the pairing of a first number of elements of (R sub i) with a second number of elements (C sub j), wherein limits of the first number are programmed in row control superneurons, and limits of the second number are programmed in column superneurons as MIN and MAX values. The cost (weight) W sub ij of the pairings is programmed separately into each PU. For each row and column of PU's, a dedicated constraint superneuron insures that the number of active neurons within the associated row or column fall within a specified range. Annealing is provided by gradually increasing the PU gain for each row and column or increasing positive feedback to each PU, the latter being effective to increase hysteresis of each PU or by combining both of these techniques.

Eberhardt, Silvio P.↗
NASA NTRS2008

Ensemble: an Architecture for Mission-Operations Software

Ensemble is the name of an open architecture for, and a methodology for the development of, spacecraft mission operations software. Ensemble is also potentially applicable to the development of non-spacecraft mission-operations- type software. Ensemble capitalizes on the strengths of the open-source Eclipse software and its architecture to address several issues that have arisen repeatedly in the development of mission-operations software: Heretofore, mission-operations application programs have been developed in disparate programming environments and integrated during the final stages of development of missions. The programs have been poorly integrated, and it has been costly to develop, test, and deploy them. Users of each program have been forced to interact with several different graphical user interfaces (GUIs). Also, the strategy typically used in integrating the programs has yielded serial chains of operational software tools of such a nature that during use of a given tool, it has not been possible to gain access to the capabilities afforded by other tools. In contrast, the Ensemble approach offers a low-risk path towards tighter integration of mission-operations software tools.

Norris, Jeffrey↗
NASA NTRS1987

A potential flight evaluation of an upper-surface-blowing/circulation-control-wing concept

The technology data base for powered lift aircraft design has advanced over the last 15 years. NASA's Quiet Short Haul Research Aircraft (QSRA) has provided a flight verification of upper surface blowing (USB) technology. The A-6 Circulation Control Wing flight demonstration aricraft has provide data for circulation control wing (CCW) technology. Recent small scale wind tunnel model tests and full scale static flow turning test have shown the potential of combining USB with CCW technology. A flight research program is deemed necessary to fully explore the performance and control aspects of CCW jet substitution for the mechanical USB Coanda flap. The required hardware design would also address questions about the development of flight weight ducts and CCW jets and the engine bleed-air capabilities vs requirements. NASA's QSRA would be an optimum flight research vehicle for modification to the USB/CCW configuration. The existing QSRA data base, the design simplicity of the QSRA wing trailing edge controls, availability of engine bleed-air, and the low risk, low cost potential of the suggested program is discussed.

Riddle, Dennis W.↗
NASA NTRS1997

A Critical Assessment of Protein Crystal Growth in Microgravity

Experiments to grow higher diffraction quality protein crystals in the microgravity environment of an orbiting spacecraft are one of the most frequently flown space experiments. Ground-based research has shown that convective flows occur even about protein crystals growing in the Earth's gravitational field. Further, this research has shown that the resultant flow velocities can cause growth cessation, and probably affect the measured X-ray data quality obtained. How flow deleteriously affects protein crystal growth (PCG) is still not known, and is the subject of ongoing research. Failing a rational method for ameliorating flow effects on Earth, one can, through NASA and other nations space agency sponsored programs, carry out protein crystal growth in the microgravity environment of an orbiting spacecraft. Early first generation PCG hardware was characterized by a very low success rate and a steep design learning curve. Subsequent hardware designs have improved upon their predecessors. Now the crystal grower has a wide variety of hardware configurations and crystal growth protocols to choose from, many of which implement "standard" laboratory protein crystal growth methods. While many of these are first or early second generation hardware the success rate, defined as growing crystals giving data better than has been obtained on Earth, is at least 20% overall and may be considerably higher if one only considers latter experiments. There are a large number of protein crystals grown every year, with hundreds of structures determined. Those crystallized in microgravity represent a small proportion of this total, and there is concern that the costs of the microgravity PCG program(s) do not justify such limited returns. Empirical evidence suggests that optimum crystal growth conditions in microgravity differ from those determined on Earth, further exacerbating the chances of success. Microgravity PCG is probably best suited for "mature" crystallizations, where one has considerable experience with the particular macromolecular system and has reached an apparent limit in diffraction resolution. Under such circumstances the cost of one or two successful flight experiments may more than offset the equivalent cost of several years effort to obtain the same improvement in data quality.

Pusey, Marc↗
NASA NTRS1991

The use of activity-based cost estimation as a management tool for cultural change

It will be shown that the greatest barrier to American exploration of the planet Mars is not the development of the technology needed to deliver humans and return them safely to earth. Neither is it the cost of such an undertaking, as has been previously suggested, although certainly, such a venture may not be inexpensive by some measures. The predicted costs of exploration have discouraged serious political dialog on the subject. And, in fact, even optimistic projections of the NASA budget do not contain the resources required, under the existing development and management paradigm, for human space exploration programs. It will be demonstrated that the perception of the costs of such a venture, and the cultural responses to the perceptions are factors inhibiting American exploration of the moon and the planet Mars. Cost models employed in the aerospace industry today correctly mirror the history of past space programs, and as such, are representative of the existing management and development paradigms. However, if, under this current paradigm no major exploration programs are feasible, then cost analysis methods based in the past may not have great utility in exploring the needed cultural changes. This paper explores the use of a new type of model, the activity based cost model, which will treat management style as an input variable, in a sense providing a tool whereby a complete, affordable program might be designed, including both the technological and management aspects.

Mandell, Humboldt↗
NASA NTRS1997

Lunar Prospector Mission Design

The National Aeronautics and Space Administration (NASA) has selected Lunar Prospector as one of the discovery missions to conduct solar system exploration science investigations. The mission is NASA's first lunar voyage to investigate key science objectives since Apollo and will be launched in September 1997. In keeping with discovery program requirements to reduce total mission cost and utilize new technology, Lunar Prospector's mission design and control will focus on the use of innovative and proven trajectory analysis programs. As part of this effort, the Ames Research Center and the Goddard Space Flight Center have become partners in the Lunar Prospector trajectory team to provide the trajectory analysis and orbit determination support. The mission design of Lunar Prospector is characterized by a direct minimum energy transfer trajectory to the moon with an injection into a circular 100 km altitude polar mapping orbit. The mission design will incorporate the optimization of the reference trajectory for a new launch vehicle. An extended mission includes a periselene altitude approaching 10 km. As part of the navigation, a new lunar potential model will be used that incorporates data from the recent Clementine mission. This paper provides understanding of the design of the Lunar Prospector mission and the optimization process of the nominal trajectory, orbit determination, launch windows, and lunar orbit targets, and discusses the feasibility of meeting the mission goals.

Folta, David↗
NASA NTRS1999

The Lunar Prospector Mission: Final Results of Trajectory Design, Quasi-Frozen Orbits, Extended Mission Targeting, and Lunar Topography and Potential Models

The National Aeronautics and Space Administration (NASA) selected Lunar Prospector (LP) as one of the discovery missions to conduct solar system exploration science investigations. The mission was NASA's first lunar voyage to investigate key science objectives since Apollo and was launched in January 1998. In keeping with discovery program requirements to reduce total mission cost and utilize new technology, Lunar Prospector's mission design and control will focus on the use of innovative and proven trajectory analysis programs. As part of this effort, the Goddard Space Flight Center and the Ames Research Center became partners in the Lunar Prospector trajectory team to provide the trajectory analysis and orbit determination support. At the end of 1998, Lunar Prospector completed its one-year primary mission at 100-km altitude above the lunar surface. On December 19, 1998, Lunar Prospector entered its extended mission phase. The mission orbit was lowered from 100 km to a mean altitude of 40 km. Due to lunar potential effects, the altitude of Lunar Prospector varied from 25 to 55 km above the mean lunar geoid. After one month at 40 km, the lunar potential model was updated based upon the new tracking data at 40 km. On January 15, 1999, the altitude was lowered again to a mean altitude of 30 km. The spherical altitude varied between 15 km and 45 km above the mean lunar geoid while the topographical altitude varied between 10 km and 50 km. Various means were employed to get accurate lunar surface elevation including Clementine altimetry and LOS analysis. Based upon the best available terrain maps, Lunar Prospector reached actual altitudes of 8 km above lunar mountains in the southern polar region. This extended mission phase of six months will enable LP to obtain science data up to 3 orders of magnitude better than at the mission orbit. At the end of the operations mission, LP was targeted for impact at a chosen location that allowed optical observation of the lunar ejecta as LP ended its mission at 1.6 km/sec. This paper details the trajectory design and orbit determination planning and actual results of the Lunar Prospector nominal and extended mission including maneuver design, eccentricity vs. argument of perigee evolution, topographical altitude estimation, and lunar potential modeling. This paper provides understanding of the quasi-frozen orbit design of the LP mission, the optimization process of lunar orbit targets, the impacts that the selected lunar potential models play, and discusses the feasibility of meeting the mission goals. Observed evolution of the Keplerian orbit elements are compared to the theoretical predictions using the latest lunar potential model available which incorporates the Lunar Prospector Doppler data. Mapping orbit maintenance maneuver design along with results of the actual maneuvers to maintain the orbital requirements are also presented.

Folta, David↗
NASA NTRS2000

Status on NGST Mirror Technology

The NGST primary mirror is anticipated to be a segmented deployable optic with segment size being in the range of 1 - 3 m depending on the details of the architecture. The secondary mirror will likely be a monolith similar in size to one of the primary mirror segments. Over the past 4 years the NGST program has initiated and implemented an aggressive lightweight cryogenic mirror technology program. The program was designed to challenge and excite the optical community in reaching a new standard in production of lightweight optics. The goal was to develop optics at less than 15 kg/sq m, operational at approx. 40 K and meeting the overall NGST observatory requirement for diffraction limited performance at 2 microns. In order to meet the NGST needs, technology efforts were initiated to investigate and develop mirrors in a variety of materials, which held promise for the program. The basic technology approaches have initially targeted the production of large mirrors in the 1.2 - 2.0 m diameter range (or side-to-side distance in the case of hexagonal optics). Although this size may not be the final size of an NGST primary mirror segment, it was felt that a 1.2 - 2.0 m optic would be of sufficient size to understand the mirror material and fabrication processes which drive the cost and schedule of mirror production. The ultimate goals of the technology program are both to demonstrate mirrors meeting, the NGST performance requirements, and to establish cost and schedule credibility for producing and implementing the mirrors for the NGST flight system. Establishing cost and schedule credibility is essential to NGST which is a cost capped mission, with past program experience demonstrating that the optics will be a large portion of the total cost of the program. The first two years of the program were dedicated to understanding; the various applicable materials, funding those materials to various levels of maturity and implementing the first large mirror procurement, the NGST Mirror System Demonstrator (NMSD), in order to establish a benchmark for the state-of-the-art in lightweight optics and to establish credibility that the goals of NGST could be achieved. The past two years of the program has seen major steps in the development of several mirror materials, which not only might have NGST applicability but could also support other programs for other customers. Additionally, a second large mirror procurement, the Advanced Mirror System Demonstrator (AMSD), has been implemented providing a focal point to complete the mirror technology development and lead ultimately to the production of mirrors that will fly on NEXUS (the NGST flight experiment- discussed below) and NGST. This talk will focus on the mirror technology developed over the past 4 years on the NGST program.

Jacobson, David↗
NASA NTRS1976

Bearing restoration by grinding

A joint program was undertaken by the NASA Lewis Research Center and the Army Aviation Systems Command to restore by grinding those rolling-element bearings which are currently being discarded at aircraft engine and transmission overhaul. Three bearing types were selected from the UH-1 helicopter engine (T-53) and transmission for the pilot program. No bearing failures occurred related to the restoration by grinding process. The risk and cost of a bearing restoration by grinding programs was analyzed. A microeconomic impact analysis was performed.

Hanau, H.↗
NASA NTRS1977

A method for reducing software life cycle costs

The advent of new hardware and software tools permits a new approach to preparing, presenting, and maintaining software specifications and corresponding source programs. Any real reduction in software life cycle costs must make highly skilled human effort more efficient especially on large, complex, and long-lasting software projects. When these skilled human functions are examined closely, it is seen that critical factors include the way one communicates with oneself and then with others and finally with computers. Thus, there has been a long and active proliferation of programming languages and, more recently, a number of programming design languages to supplement older methods, such as flowcharting. One way to achieve cost reduction is to provide documentation tools whose use increases the effectiveness of skilled humans.

Paine, W. O.↗
NASA NTRS1987

Assessment Of Advanced Concentrator Photovoltaic Modules

Computer program developed to estimate probabilistically total and component costs to end users of concentrating photovoltaic arrays in 1990's. Based on modified version of SIMRAND program, Simulation of Research and Development projects, -to estimate total cost of system for large number of module designs. Module design that yields minimum cost for total system then chosen as preferred design. To obtain distribution of expected module costs, simulation performed. Component estimates made by SIMRAND include efficiency of module and costs of cell, assembly of cells, lenses, and modules. Written in FORTRAN 77.

Borden, C. S.↗
DOE OSTI2025

Life-Cycle Cost Analysis Framework for Water Efficiency Measures

Life-Cycle Cost Analysis Framework for Water Efficiency Measures: Guidance Designed for Federal Agencies (hereafter referred to as “this report”) provides a technical framework for federal agencies to conduct a life-cycle cost analysis (LCCA) for water efficiency projects in accordance with 42 U.S.C. § 8253. This report leverages insights from the 2023 report, PNNL-34006, Water and Wastewater Annual Price Escalation Rates for Selected Cities Across the United States: 2023 Edition (Unger et al. 2023). The primary objective of this report is to provide a framework to assist federal agencies with evaluating the full economic impact of water efficiency projects by assessing both initial investments and long-term operational benefits. An LCCA can provide a comprehensive view of all costs associated with a water efficiency project, including initial investment, ongoing operations and maintenance (O&M), and eventual disposal or replacement, ensuring the most cost-effective solution is selected. The LCCA methodology outlined in this report enables users to compare base case scenarios with potential alternatives using a standardized present value approach. It incorporates key cost components such as energy, water and wastewater, installation, O&M, and equipment replacement. Additionally, the framework introduces relevant evaluation metrics, such as the net savings and the savings-to-investment ratio, to ensure that water efficiency measures are economically justified over the lifespan of the project. To support practical application, this report also describes various water efficiency strategies that may be analyzed using an LCCA, including plumbing retrofits, irrigation upgrades, alternative water use, and cooling system improvements. By applying this framework, federal agencies can ensure compliance with regulatory mandates while maximizing the return on investment and contributing to resilient water management practices. The information provided in this report is aligned with the Federal Energy Management Program (FEMP) life-cycle cost (LCC) methodology, as conveyed in National Institute of Standards and Technology (NIST) Handbook 135 (Kneifel and Webb 2022). This report is intended to provide relatively high-level guidance, acting as a complement to, rather than a substitute for, that resource.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2021

5.5 Hybrid Additively Manufactured Tooling for Large Composite Structures

This program sought to lower tooling costs for tightly toleranced, large composite aerostructures by using large format additive manufacturing (LFAM). LFAM tooling has the potential to lower tooling costs, but the large and unpredictable thermal expansion of polymer-based tooling did not previously allow for the production of large structures made with high performance resins requiring 350 deg F cures. Geometric tolerance issues and demolding concerns continued to arise. The proposed approach for this work was to print a thin shell via additive manufacturing that would be used as a scaffold for a conventional tooling prepreg. The prepreg would be laminated and cured onto both sides of the shell, creating a tool with a sandwich construction. The cured prepreg would then be machined and serve as the tooling surface. In addition to providing a clean, pit-free surface, the prepreg stiffness and low thermal expansion would physically restrain the AM shell and prevent it from expanding during thermal cycling, thus preventing any geometric mismatch between the nominal and actual part dimensions. A stair-step approach was taken to prove out this approach. Coupon level testing was done to ensure a good bond was possible between the AM shell and the tooling prepreg. These samples were also used to determine the amount of prepreg needed to achieve the desired coefficient of thermal expansion (CTE). The project team than progressed to a subscale tool measuring two feet in length. The geometry used was a C-section spar from Airbus’ Wing of Tomorrow program. A hybrid tool, using the AM shell and tooling prepreg, was made, and a composite part was fabricated with the tool. Dimensional scans of the tool and part indicated that the desired CTE was achieved with the tool. A second tooling approach was taken to reduce risk. In this approach, a subscale tool of the same geometry as previously mentioned was created, but the tool was entirely constructed of the tooling prepreg. AM was used to print a “master” that was then used to fabricate the tool by creating a splash off of the master using tooling prepreg. The innovation was that the master was not machined, but rather, was used right off the printer after a small amount of surface preparation. Removing this machining step was thought to make this approach economically viable when compared to conventional master fabrication. As before, the tool was used to fabricate a part and tested for dimensional accuracy. For the conclusion of the program, a ten-foot tool was created using the hybrid tool approach. The geometry also came from the Airbus C-section spar previously mentioned. Some difficulty arose in accurately predicting the geometry of the tool after laminating the tooling prepreg, resulting in multiple material additions and a tool geometry change. A part was fabricated in an autoclave using the tool. A cost savings of almost 50% was achieved on the subscale tool in both the hybrid and master-style tool, but the savings dropped considerably as the tool length increased in the full-scale tool. Given the less than expected cost savings and added complexity of the tool construction, it is suggested that the master-style tool is best for immediate commercialization for larger tools (although it may be appropriate for smaller, table-top size tools). Since its construction is very similar to conventionally made composite tooling, there already exists a broad supply chain for building the tool, and project partner Additive Engineering Solutions (AES) is well acquainted with the design and build of the AM master needed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Elimination of human rabies in Goa, India through an integrated One Health approach

Dog-mediated rabies kills tens of thousands of people each year in India, representing one third of the estimated global rabies burden. Whilst the World Health Organization (WHO), World Organization for Animal Health (OIE) and the Food and Agriculture Organization of the United Nations (FAO) have set a target for global dog-mediated human rabies elimination by 2030, examples of large-scale dog vaccination programs demonstrating elimination remain limited in Africa and Asia. We describe the development of a data-driven rabies elimination program from 2013 to 2019 in Goa State, India, culminating in human rabies elimination and a 92% reduction in monthly canine rabies cases. Smartphone technology enabled systematic spatial direction of remote teams to vaccinate over 95,000 dogs at 70% vaccination coverage, and rabies education teams to reach 150,000 children annually. An estimated 2249 disability-adjusted life years (DALYs) were averted over the program period at 526 USD per DALY, making the intervention ‘very cost-effective’ by WHO definitions. This One Health program demonstrates that human rabies elimination is achievable at the state level in India.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1979

Reduction of computer usage costs in predicting unsteady aerodynamic loadings caused by control surface motions: Computer program description

A digital computer program was developed to calculate unsteady loadings caused by motions of lifting surfaces with leading edge and trailing edge controls based on the subsonic kernel function approach. The pressure singularities at hinge line and side edges were extracted analytically as a preliminary step to solving the integral equation of collocation. The program calculates generalized aerodynamic forces for user supplied deflection modes. Optional intermediate output includes pressure at an array of points, and sectional generalized forces. From one to six controls on the half span can be accomodated.

Petrarca, J. R.↗