Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Real time intelligent process control system for thin film solar cell manufacturing

This project addresses the problem of lower solar conversion efficiency and waste in the typical solar cell manufacturing process. The work from the proposed development will lead toward developing a system which should be able to increase solar panel conversion efficiency by an additional 12-15% resulting in lower cost panels, increased solar technology adoption, reduced carbon emissions and reduced dependency on foreign oil. All solar cell manufacturing processes today suffer from manufacturing inefficiencies that currently lead to lower product quality and lower conversion efficiency, increased product cost and greater material and energy consumption. This results in slower solar energy adoption and extends the time solar cells will reach grid parity with traditional energy sources. The thin film solar panel manufacturers struggle on a daily basis with the problem of thin film thickness non-uniformity and other parameters variances over the deposited substrates, which significantly degrade their manufacturing yield and quality. Optical monitoring of the thin films during the process of the film deposition is widely perceived as a necessary step towards resolving the non-uniformity and non-homogeneity problem. In order to enable the development of an optical control system for solar cell manufacturing, a new type of low cost optical sensor is needed, able to acquire local information about the panel under deposition and measure its local characteristics, including the light scattering in very close proximity to the surface of the film. This information cannot be obtained by monitoring from outside the deposition chamber (as traditional monitoring systems do) due to the significant signal attenuation and loss of its scattering component before the reflected beam reaches the detector. In addition, it would be too costly to install traditional external in-situ monitoring systems to perform any real-time monitoring over large solar panels, since it would require significant equipment refurbishing needed for installation of multiple separate ellipsometric systems, and development of customized software to control all of them simultaneously. The proposed optical monitoring system comprises AccuStrata’s fiber optics sensors installed inside the thin film deposition equipment, a hardware module of different components (beyond the scope of this project) and our software program with iterative predicting capability able to control material bandgap and surface roughness as films are deposited. Our miniature fiber optics monitoring sensors are installed inside the vacuum chamber compartments in very close proximity where the independent layers are deposited (an option patented by us in 2003). The optical monitoring system measures two of the most important parameters of the photovoltaic thin films during deposition on a moving solar panel - material bandgap and surface roughness. In this program each sensor array consists of two fiber optics sensors monitoring two independent areas of the panel under deposition. Based on the monitored parameters and their change in time and from position to position on the panel, the system is able to provide to the equipment operator immediate information about the thin films as they are deposited. This DoE Supply Chain program is considered the first step towards the development of intelligent optical control system capable of dynamically adjusting the manufacturing process “on-the-fly” in order to achieve better performance. The proposed system will improve the thin film solar cell manufacturing by improving the quality of the individual solar cells and will allow for the manufacturing of more consistent and uniform products resulting in higher solar conversion efficiency and manufacturing yield. It will have a significant impact on the multibillion-dollar thin film solar market. We estimate that the financial impact of these improvements if adopted by only 10% of the industry ($7.7 Billion) would result in about $1.5 Billion in savings by 2015 (at the assumed 20% improvement). This can be achieved by optimizing the manufactured product and process in real time without changing the manufacturing technology.

14 SOLAR ENERGY↗

Models of the diffuse radar backscatter from Mars

The topographies of several debris flow units near the Mount St. Helens Volcano were measured at lateral scales of millimeters to meters in September 1990. The objective was to measure the surface roughness of the debris flows at scales smaller than, on the order of, and larger that the radar wavelength of common remote sensing radars. A laser profiling system and surveying instruments were used to obtain elevation data for square areas that varied in size from 10 to 32 cm. The elevation data were converted to estimates of the power spectrum of surface roughness. The conversions were based upon standard periodogram techniques, and upon a modified spectral estimation technique that was developed.

England, A. W.↗

Optimization of Processing, Microstructure, and Hardness of an Al–Ce–Ni–Mn–Zr Alloy With Laser Additive Manufacturing

Here, this study examines the processing behavior, microstructure, surface roughness, and hardness properties of an aluminum alloy containing 8.2 Ce, 4.5 Ni, 0.5 Mn, and 0.7 Zr (wt%) fabricated using laser powder bed fusion. Sixty samples were produced across a range of laser powers, scan speeds, and hatch spacings to evaluate their effect on porosity, hardness, and microstructural features. Porosity was measured using X-ray computed tomography, while microstructure and surface roughness were characterized by scanning electron (SEM) and laser confocal microscopy. High dense and cracking-free Al–Ni–Ce alloy was successfully manufactured. Porosity showed a U-shaped dependence on energy input, increasing under both insufficient and excessive melting conditions. Hardness increased with cooling rate due to finer cellular structures and solute redistribution. A general statistical model was developed to capture the relationships between processing parameters and material response. Results identify a narrow processing window defined by laser powers between 350 and 370 W, scan speeds from 1400 to 1800 mm/s, and hatch distances between 0.14 and 0.18 mm. Within this window, porosity is minimized (below 0.01%) and hardness is maximized (up to 160 HV), demonstrating that careful control of these parameters enables dense, high strength aluminum components suitable for demanding structural applications.

Aluminum alloys↗

Development of High-Quality, Very Large-Grained Cd(Se,Te) Thin Films for CdTe Solar Modules (Final Technical Report)

TCF-21-25048 is a one-year project to quantify the potential attributes of recent NREL inventions where CdTe devices with grain sizes exceeding 100's of microns in lateral dimension can be fabricated using a novel seeded-epitaxial process. A CdSe0.1Te0.9 film is evaporated on commercially available transparent conducting oxide (TCO) where the latter surface roughness (Ra) has been reduced to < 1-nm. After NREL's colossal grain growth (CGG) process, the grain size of this "seed" layer is increased to 100-1000 um. CdTe is then deposited epitaxially resulting in a large-grain CdTe device structure without use of CdCl2. As of this report, we have: Demonstrated the feasibility of using Tec-15 substrates after surface roughness (Ra) reduction (nexTC); Developed reproducible CGG processes for this commercially available substrate; Developed a close-spaced sublimation (CSS) process for CdTe epitaxy using these substrates; Demonstrated that large-grain CdTe films have less sub-band (band tail) absorption than conventional, small-grain CdTe; Demonstrated that large-grain CdTe films (no CdCl2) have carrier lifetimes up to 1.5 ns; Demonstrated that carrier lifetimes in epi-CdTe films (no CdCl2) have comparable lifetimes when compared to the best pX-CdTe films (FSLR) treated with CdCl2; Started making large-grain CdTe devices using CGG templates and epitaxially deposited CdTe.

14 SOLAR ENERGY↗

Interaction between the atmospheric and oceanic boundary layers

The two-layer system of an atmosphere over water bodies is reduced to a single-layer problem. Values of the interfacial quantities, such as the friction velocity, the surface velocity, the angles, alpha and beta, between the surface shear stress and the geostrophic wind velocity and the surface wind velocity, respectively, and the surface roughness, all of which depend upon external parameters, such as the geostrophic wind and stratifications, are obtained. The geostrophic drag coefficient, the geostrophic wind coefficient, and the angles alpha, and beta, of the turbulent flow at the sea-air interface are functions of a dimensionless number, mfG/kg, with S sub 1 and S sub 2 as two free stratification parameters. The surface roughness is uniquely determined from the geostrophic wind rather than from the wind profile in the boundary layer.

Yeh, G.-T.↗

Electron transport and defect structure in highly conducting reactively sputtered ultrathin tin oxide films

Electrical conduction behavior of ultrathin (5–110 nm) SnO{sub 2} films reactively sputtered at 150–400 °C substrate temperatures is presented. The surface roughness studies revealed that the films with lower thickness were smoother (≤0.6 nm). Stoichiometry/defect structure of the films obtained from X-ray photoelectron spectroscopy data and electron mobility are found to be dependent on film thickness and substrate temperature. The observed increase in conductivity of semi-metallic films with decrease in film thickness is attributed to changes in defect structure and surface roughness. Highest value of conductivity of about 715 Ω{sup −1} cm{sup −1} is obtained for 5 nm thick films deposited at 300 °C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Degradation of Ta 2 O 5 / SiO 2 dielectric cavity mirrors in ultra-high vacuum

In order for optical cavities to enable strong light-matter interactions for quantum metrology, networking, and scalability in quantum computing systems, their mirrors must have minimal losses. However, high-finesse dielectric cavity mirrors can degrade in ultra-high vacuum (UHV), increasing the challenges of upgrading to cavity-coupled quantum systems. We observe the optical degradation of high-finesse dielectric optical cavity mirrors after high-temperature UHV bake in the form of a substantial increase in surface roughness. We provide an explanation of the degradation through atomic force microscopy (AFM), X-ray fluorescence (XRF), selective wet etching, and optical measurements. We find the degradation is explained by oxygen reduction in Ta 2 O 5 followed by growth of tantalum sub-oxide defects with height to width aspect ratios near ten. We discuss the dependence of mirror loss on surface roughness and finally give recommendations to avoid degradation to allow for quick adoption of cavity-coupled systems.

Optics↗

Latitudinal variation of wind erosion of crater ejecta deposits on Mars

The characteristics of wind erosion as the dominant process involved in eroding crater ejecta deposits on Mars are studied. Present-day crater formation in mid to high latitudes involves impact into some thickness of aeolian debris, while impact in the equatorial zone is more likely to involve target materials consisting of coarse-grained aeolian lag deposits or even bedrock. Latitudinal variation dominates differences in ejecta emplacement mechanisms and probably differences in patterns of wind erosion of ejecta and surrounding intercrater materials. Escarpments develop as the deposits are eroded back toward crater rims. Erosion only takes places at escarpment edges where surface roughness may be low enough to allow particle entrainment. Preferential preservation of ejecta emplaced in thick debris may occur. An empirical model developed for wind erosion of ejecta deposits in nonmantled areas suggests that removal of ejecta materials on the average is exceedingly slow. Results suggest high differential aeolian erosion rates that are a function of both grain sizes and large-scale surface roughness.

Arvidson, R. E.↗

Characterization of multi-material 316L-Hastelloy X fabricated via laser powder-bed fusion

The aim of this work is to provide firsthand knowledge of 316 L stainless steel (316 L) and Hastelloy X (HX) multi-material processing via laser powder bed fusion (PBF). Specifically, microstructure of the interface is studied using scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS), and X-ray diffraction (XRD). Surface metrology is performed to characterize the resulting surface roughness at the interface followed by tensile and flexural testing of multi-material samples to characterize the mechanical properties of the interfaces. Results showed that use of proper process parameters for each individual material led to formation of a compositional gradient at the interface that stretched for 240 μm (10–12 layers) with no evidence of cracking or porosity. The interface exhibited higher surface roughness compared to 316 L or HX as measured by arithmetic mean height, Sa, and maximum valley depth, Sv, parameters. During tensile testing, samples failed in the 316 L region away from the interface, with comparable yield strength, ultimate strength, and ductility. Finally, it was concluded that the “naturally” formed interface created a compositional gradient which was defect free due to similar values of coefficient of thermal expansion, input energy density, and different Marangoni numbers of the materials.

316L stainless Steel↗

Computational Study of Low-Speed Boundary-Layer Laminar-Turbulent Transition over a 30º Swept Plate in a Channel

Reliable boundary-layer laminar-turbulent transition predictions are critical for the design of aircraft that use natural or controlled laminar flow to achieve low drag and better fuel efficiency. During cruise flight through low turbulence, the three-dimensional boundary layer over swept surfaces can transition prematurely due to stationary crossflow instabilities induced by surface roughness. Parabolized stability equations analyses have been successfully used to explain the different phases of the transition process under well controlled perturbations such as steps or discrete roughness elements. However, methodologies are still lacking to model the boundary layer receptivity to distributed random roughness, and the following non-linear instability stages leading to transition. For engineering applications, several semi-empirical methods based on linear amplification factors or local helicity have found growing adoption, but their reliability is limited by their level of simplification and the sparsity of data they are based on. To address this gap, a new study of the effect of distributed random surface roughness on crossflow transition was started, using a 30◦ swept plate as a test vehicle. The plate, which is mounted in the 2 Foot × 3 Foot Low-Speed Boundary-Layer Channel at the NASA Langley Research Center, has been tested with micro-scale roughness of varied geometry near the leading edge. In order to analyze the flow in the test section and prepare Direct Numerical Simulations with resolved roughness, Reynolds-Averaged Navier-Stokes (RANS) simulations of the flow over the plate installed in the wind tunnel test section were performed using the Langtry-Menter transition model with stationary crossflow extension. This paper presents the results of these simulations, with comparison to the experiment.

ARMD↗

Surface Characteristics of Titanium during ECM Process for Biomedical Applications

Electrochemical machining is described as the controlled removal of metal by anodic dissolution of the workpiece in electrolyte cell. Titanium is extensively used in aerospace, defence, biomedical applications. The human response to implanted titanium parts strongly related to the implant surface conditions. The aim of this paper is to present experimental investigation on electrochemically machined surface characteristics acquired on titanium, utilizing developed cross flow electrolyte system. It is observed that applied voltage and electrolyte flow rate are the some of the persuading parameter to attain desired surface characteristics on machined surface. Attempt has made to develop surface along with self-generated oxide layer, which facilitates in improving the corrosion and chemical resistance of titanium implant in biomedical application. The surface roughness of oxide layered machined surface obtained within 2.4 {mu}m to 2.93 {mu}m, which is within acceptable value for functional attachment between bone and implant.

36 MATERIALS SCIENCE↗

Strain-Driven Evolution of Structural and Carrier Recombination Dynamics in Germanium

Strain engineering in group-IV semiconductors, in particular germanium (Ge), offers a promising route for advancing next-generation optoelectronic device performance. High minority carrier lifetime serves as a direct indicator of superior material quality and device efficiency. Several factors govern the minority carrier lifetime in both strained Ge and strained GeSn, such as strain level, epilayer thickness, defects, surface roughness, and Sn alloying. In this study, the impact of biaxial strain on effective minority carrier lifetimes of tensile-strained Ge (0% ..epsilon..-Ge/Al?As, 0.78% ..epsilon..-Ge/In0.115?Ga0.885?As, and 0.93% ..epsilon..-Ge/In0.16?Ga0.84?As) and compressively strained GeSn (-0.53% c-Ge0.97?Sn0.03/Al?As) epilayers, grown by molecular beam epitaxy, was experimentally investigated via the microwave-reflection photoconductive decay (..mu..-PCD) technique as a simultaneous function of thickness and strain. The structural and strain-relaxation properties were analyzed by high-resolution x-ray diffraction and Raman spectroscopy, while surface morphology analysis using atomic force microscopy provided insights into the surface roughness of strained Ge-based epilayers. Defect characterization by cross-section transmission electron microscopy revealed superior crystalline quality of ..epsilon..-Ge in one epilayer, while twin boundary formation was observed in the other. We investigated the carrier recombination dynamics in epitaxially strained Ge by extracting the bulk recombination lifetime and surface recombination velocity using the thickness-dependent minority carrier lifetime. High effective minority carrier lifetimes of approximately 60-340 ns were achieved at high strain levels with minimal dependence on the thickness of the strained Ge-based epilayers by means of the ..mu..-PCD technique. Minority carrier lifetimes in Ge-based epilayers exhibit a quadratic dependence on the biaxial strain, ranging from -0.88% (compressive) to +1.6% (tensile). The analysis of the carrier recombination dynamics in strained Ge-based heterostructures offers a pathway to designing group-IV based optoelectronic devices.

36 MATERIALS SCIENCE↗

Materials Study of NbN and Ta x N Thin Films for SNS Josephson Junctions

We investigated properties of NbN and Ta x N thin films grown at ambient temperatures on SiO 2 /Si substrates by reactive-pulsed laser deposition and reactive magnetron sputtering (MS) as a function of N 2 gas flow. Both techniques produced films with smooth surfaces, where the surface roughness did not depend on the N 2 gas flow during growth. High crystalline quality, (111) oriented NbN films with T c up to 11 K were produced by both techniques for N contents near 50%. The low temperature transport properties of the Ta x N films depended upon both the N 2 partial pressure used during growth and the film thickness. Furthermore, the root mean square surface roughness of Ta x N films grown by MS increased as the film thickness decreased down to 10 nm.

36 MATERIALS SCIENCE↗

Effect of Oxygen Content on Wear and Cutting Performance of AlCrON Coatings

In this work, AlCrON coatings with various oxygen contents were deposited by multi-arc-ion plating technology. The effects of oxygen content on the microstructure, mechanical properties, wear and cutting performance of AlCrON coatings were investigated. The result showed that the O contents in the AlCrON coatings increased from 0 to 8.8 wt.% by changing the O{sub 2}/N{sub 2} flow ratios during the deposition process. The AlCrON coatings mainly included fcc-CrN and fcc-AlN phases, and the Al{sub 2}O{sub 3} and Cr{sub 2}O{sub 3} were also confirmed by the XPS results. Addition of oxygen improved the adhesion strength of AlCrON coatings. The AlCrON coating with 4.0 wt.% oxygen content showed the low surface roughness, low friction coefficient and the minimum wear rate. Cutting results also showed that addition of oxygen improved the service life of AlCrON coatings under various cutting conditions. The service life of AlCrON coatings increased firstly and then decreased with increasing oxygen contents, and the AlCrON coating with 4.0 wt.% oxygen content had the maximum cutting length under various cutting conditions, which might be due to the decrease of surface roughness, increase of adhesion strength and hardness. The wear mechanism involved in cutting process included abrasive wear, adhesive wear and oxidation wear.

36 MATERIALS SCIENCE↗

Sputter-deposited (Pb,La)(Zr,Ti)O{sub 3} thin films: Effect of substrate and optical properties

Optically transparent (Pb,La)(Zr,Ti)O{sub 3} (PLZT) thin films were sputter-deposited on SrTiO{sub 3}(001) and MgO(001) substrates with a SrRuO{sub 3}(110) bottom electrode. X-ray diffraction analysis showed epitaxial growth of monocrystalline PLZT, with (001) rocking curve full width at half maxima of {approx}0.03 degree sign and {approx}0.3 degree sign for films deposited on SrTiO{sub 3} and MgO, respectively. In-plane epitaxial alignment of the SrRuO{sub 3} and PLZT epilayers was verified from {phi}-scans. It was established from atomic force microscopy measurements that the PLZT surface roughness meets the requirement for optical waveguide applications. Recorded P-E loops for films grown on both substrates showed a remanent polarization of {approx}36 {mu}C/cm{sup 2}. The refractive index of the PLZT layer was estimated from rutile prism coupling measurements at {approx}2.56 for {lambda}=633 nm, consistent with data obtained by spectroscopic ellipsometry. The ferroelectric and optical characteristics of the films, as well as their surface roughness, were not appreciably different for the two substrates. This makes MgO the preferred choice of substrate for optical waveguide devices due to its low refractive index compared to that of SrTiO{sub 3}.

36 MATERIALS SCIENCE↗

Experimental flow-through a single fracture with monolayer proppant at reservoir conditions: A case study on Caney Shale, Southwest Oklahoma, USA

Global energy systems are undergoing a crucial transition to clean energy sources, thereby moving away from fossil-fuel based energy with the ultimate aim of reducing carbon dioxide emissions. It is essential to continue to advance in exploring and developing shale gas resources as this will underpin the global supply of natural gas that is needed to support the energy transition. The challenge hereby is that the slow fluid flow of the shale matrix due to its very low permeability requires large-scale volume fracturing to produce a conductive fracture network that enhances the connectivity between the shale formation and the wellbore. This work examines the influence of a thin proppant layer on a single fracture using a flow-through experiment, and also explores whether proppant embedment in the Caney shale is affected by the rock mineralogy, surface roughness, fluids, confining stress, time, temperature and bedding. The experiment was conducted for a duration of nine days (216 h), experimental temperature was varied from ambient temperature to reservoir temperature of 125 °C (257 °F) and confining stress was varied from 367 psi (2.53MPa) to a maximum of 4011.82 psi (27.66 MPa). Here, we find that the conductivity of the fracture is primarily influenced by the layer of proppant used, surface roughness, mineralogy, fluids, temperature and closure stress.

Caney shale↗

Imaging radar observations of volcanic features in Medicine Lake Highland, California

Synthetic aperture L-band radar images of Medicine Lake Highland, California, as obtained from the JPL-NASA aircraft and Seasat orbital systems, are presented. Image interpretation is based on two types of information: slope and topographic effects for geomorphic information, and reflectivity or backscatter in flat terrain which is related to surface roughness and to the surface dielectric constant. Cinder cones and lava tubes are visible (geomorphic features), and three types of lava surfaces are: aa, pahoehoe, and block. In addition, to infer lava flow relative ages, overlapping flow fronts and roughness attenuation observations may be used. It is hoped that this research will improve the understanding of the radar signature of volcanic areas, and will be helpful in interpreting data obtained from spaceborne sensors over the earth and, in particular, Venus.

Farr, T. G.↗

Alternate Methods for Cleaning Zirconium Plate

The United States High Performance Research Reactor Conversion Program identified the need to transition from highly enriched uranium fuel to lowly enriched uranium fuel for high power research and civil reactors. One of the fuel configurations selected for these reactors was a uranium (U) foil alloyed with 10% molybdenum (Mo). The U-10Mo fuel foil was then covered with a zirconium (Zr) interlayer and pressed into an aluminum cladding. Idaho National Laboratory prescribed a need to remove surface oxidation on the Zr prior to bonding it with U-10Mo fuel foil. To determine the best method of oxidation removal, a variety of polishing methods, including hand polishing with a diamond paste or Scotch-Brite™ pads, mechanically wet-polishing with abrasive belts, and chemical etching with hydrofluoric/nitric acid mixtures, were investigated on pre-polished Zircaloy 702 sheets purchased directly from the manufacturer. No change in surface roughness was detected using any of these methods relative to the as-received material. In fact, scanning electron microscopy detected grit from hand polishing with Amplex Grade 30 waste soluble diamond paste and Scotch-Brite™ pads. Visible staining was found, and fluorine detected via X-ray photoelectron spectroscopy on the flash etching samples. These contaminants were not seen on the as-received material. In addition to the need to remove the oxide layer on the Zr prior to co-rolling, there are concerns that the Neolube debonding agent on the co-rolling can may contaminate the Zr surface after co-rolling. The experimental results found that zirconium in contact with Neolube coated steel plates was easily cleaning with ethanol wiping after heat treated and no carbide inclusions remained on the surface. Overall, all cleaning methods tested did not significantly change the surface roughness of the plates or reduce the oxide layer present on the zirconium. Carbon was found on all the samples, before and after cleaning, except for the flash etch samples which detected fluorine instead. The insignificant changes seen in the cleaned plates relative to the as received plates question the need for cleaning prior to rolling. Further investigation in the requirements for cleaning at this step is recommended. Current methods for cleaning the surface after hot rolling with alcohol appear sufficient. After hot rolling, if Neolube does peel off the can and onto the zirconium coated foil surface, a dry abrasive or diamond paste polish is not recommended due to the chance of abrasive being embedded into the surface. However, the ability of an etchant to lift the lubricant off the zirconium surface indicates that a spot etch method could work to clean specific spots where Neolube is present, if the need arises.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗