Search NASA⌕ Search

SEARCH · Search NASA

Results for “sharp transition”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

Development of perturbations in the boundary layer

The transition of laminar flows into turbulent flows in a boundary layer is discussed. The individual aspects of the transition process, observed under controllable model conditions are examined. The aspect of this problem, namely the development or excitation of the natural oscillations in the boundary layer, the so-called Tollmin-Schlichting waves is covered. Three types of excitation of these waves are considered: (1) distributed generation throughout the boundary layer; (2) generation in the vicinity of the forward edge of a model, having either a sharp edge or an edge with a large radius or curvature, and (3) generation in a developed boundary layer by means of a focused effect.

Dovgal, A. V.↗

Enhancement of the Curie temperature in single-crystalline ferromagnetic LaCrGe 3 by electron irradiation-induced disorder

LaCrGe 3 has attracted attention as a potential candidate for studies of quantum phase transitions in a ferromagnetic material. The application of pressure avoids a quantum critical point by developing a new magnetic phase. It was suggested that the disorder may provide an alternative route to a quantum critical point. We used low-temperature 2.5 MeV electron irradiation to induce relatively small amounts of pointlike disorder in single crystals of LaCrGe 3 . Irradiation leads to an increase of the resistivity at all temperatures with some deviation from the Matthiessen rule. Hall effect measurements show that electron irradiation does not cause any detectable change in the carrier density. Unexpectedly, the Curie temperature, T FM , increases with the increase of disorder from approximately 90 K in pristine samples up to nearly 100 K in the heavily irradiated sample, with a tendency towards saturation at higher doses. This effect is observed both in resistivity and magnetization measurements. Although the mechanism of this effect is not entirely clear, we conclude that it cannot be caused by effective “doping” or “pressure” due to electron irradiation. Finally, we suggest that disorder-induced broadening of a sharp peak in the density of states, D⁡(E), situated at E p = E F – 0.25 eV below the Fermi energy, E F , causes an increase in D⁡(E F ), leading to an enhancement of T FM in this itinerant ferromagnet.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Carrier Mobility Modulation in Cu 2 Se Composites Using Coherent Cu 4 TiSe 4 Inclusions Leads to Enhanced Thermoelectric Performance

Carrier transport engineering in bulk semiconductors using inclusion phases often results in the deterioration of carrier mobility (μ) owing to enhanced carrier scattering at phase boundaries. Here, we show by leveraging the temperature-induced structural transition between the α-Cu 2 Se and β-Cu 2 Se polymorphs that the incorporation of Cu 4 TiSe 4 inclusions within the Cu 2 Se matrix results in a gradual large drop in the carrier mobility at temperatures below 400 K (α-Cu 2 Se), whereas the carrier mobility remains unchanged at higher temperatures, where the β-Cu 2 Se polymorph dominates. The sharp discrepancy in the electronic transport within the α-Cu 2 Se and β-Cu 2 Se matrices is associated with the formation of incoherent α-Cu 2 Se/Cu 4 TiSe 4 interfaces, owing to the difference in their atomic structures and lattice parameters, which results in enhanced carrier scattering. In contrast, the similarity of the Se sublattices between β-Cu 2 Se and Cu 4 TiSe 4 gives rise to coherent phase boundaries and good band alignment, which promote carrier transport across the interfaces. Interestingly, the different cation arrangements in Cu 4 TiSe 4 and β-Cu 2 Se contribute to enhanced phonon scattering at the interfaces, which leads to a reduction in the lattice thermal conductivity. The large reduction in the total thermal conductivity while preserving the high power factor of β-Cu 2 Se in the (1–x)Cu 2 Se/(x)Cu 4 TiSe 4 composites results in an improved ZT of 1.2 at 850 K, with an average ZT of 0.84 (500–850 K) for the composite with x = 0.01. Furthermore, this work highlights the importance of structural similarity between the matrix and inclusions when designing thermoelectric materials with improved energy conversion efficiency.

36 MATERIALS SCIENCE↗

High-pressure behavior of amorphous selenium from ultrasonic measurements and Raman spectroscopy

The high-pressure behavior of melt-quenched amorphous selenium (a-Se) has been investigated via ultrasonic measurements and Raman scattering at room temperature. The ultrasonic measurements were conducted on a-Se in a multi-anvil apparatus with two different sample assemblies at pressures of up to 4.5 and 4.8 GPa. We discovered that similar kinks occur in the slopes of the pressure dependence characteristics of the travel time and the sound velocity in both shear and longitudinal waves in the 2.0–2.5 GPa range. These kinks are independent of the sample assemblies, indicating an intrinsic transformation of the a-Se. Additionally, we deduced the pressure-volume relationship of a-Se from the sound velocity characteristics using the Birch–Murnaghan equation of state, and the results agreed well with those of previous reports. In situ high-pressure Raman scattering measurements of a-Se were conducted in a diamond anvil cell with an 830 nm excitation line up to a pressure of 4.3 GPa. We found that the characteristic band of a-Se at ∼250 cm{sup −1} experienced a smooth shift to a lower frequency with pressure, but a sharp slope change in the band intensity versus pressure occurred near 2.5 GPa. The results of X-ray diffraction and differential scanning calorimetry measurements indicate that the samples remain in their amorphous states after decompression. Thus, we proposed that the abnormal compression behavior of a-Se in the 2.0–2.5 GPa range can be attributed to pressure-induced local atomic reconfiguration, implying an amorphous-amorphous transition of the elementary selenium.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Parametric study of optical transmission through plasmonic hole arrays modulated by the phase transition of vanadium dioxide

We have performed comprehensive electromagnetic simulations and preliminary experiments to explore the effects of geometrical and material parameters on the extraordinary optical transmission (EOT) through periodic arrays of subwavelength holes in a bilayer stack consisting of a gold or silver film atop a vanadium dioxide film (Au/Ag + VO 2 ), where the latter undergoes a semiconductor-to-metal phase transition. Using the finite-difference time-domain (FDTD) and finite-element methods (FEM), we vary iteratively the array periodicity, VO 2 film thickness and hole diameters, as well as the refractive index inside the VO 2 -layer holes and the VO 2 optical constants. For each variation, we compare the metallic-to-semiconducting ratios of the zero-order transmission ( T 00 ) peaks and find sharp maxima in these ratios within narrow parameter ranges. The maxima arise from Fabry-Perot and Fano-type resonances that minimize T 00 in the semiconducting phase of the perforated bilayers. At a fixed array period, the primary factors controlling the VO 2 -enabled EOT modulation are the VO 2 thickness, diameter of the VO 2 -layer holes, and absorption in the two VO 2 phases. Besides uncovering the origins of the higher metallic-phase T 00 , this study provides a protocol for optimizing the performance of the bilayer hole arrays for potential uses as dynamically tunable nano-optical devices.

Donev, Eugenii U. (ORCID:000000030555219X)↗

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Hydrodynamic instability↗

Surface plasmon resonance induced Er{sup 3+} photoluminescence enhancement in tellurite glass

The melt quenching method is used to prepare tellurite glasses co-activated with erbium ions and silver nanoparticles (Ag NPs). The glass samples are characterized by x-ray diffraction, UV-vis-NIR absorption, transmission electron microscopy (TEM) imaging, and photoluminescence spectroscopy. The XRD pattern shows no sharp peak indicating an amorphous nature of the glasses. The presence of Ag NPs is confirmed from TEM micrograph. The absorption spectra reveal not only the peaks due to Er{sup 3+} ions, but also the surface plasmon resonance band of silver NPs in the 510–535 nm range. The J-O model has been applied to the room temperature absorption intensities of Er{sup 3+} (4f{sup 11}) transitions to establish the so-called J-O intensity parameters: Ω{sub 2}, Ω{sub 4}, and Ω{sub 6}. The intensity parameters are used to determine the radiative decay rates (emission probabilities of transitions) and branching ratios of the Er{sup 3+} transitions from the excited state J manifolds to the lower-lying J' manifolds. Intensified of 1.53 μm band is obtained for the sample containing 0.5 mol. % of AgNO{sub 3} (Ag0.5 glass) using for excitation a laser operating at 980 nm. The simultaneous influence of the Ag NPs → Er{sup 3+} energy transfer and the contribution of the intensified local field effect due to the silver NPs give origin to the enhancement of both the Photoluminescence (PL) intensity and the PL lifetime relative to the {sup 4}I{sub 13/2} → {sup 4}I{sub 15/2} transition, whereas the quenching is ascribed to the energy transfer from Er{sup 3+} ions to silver NPs. Based on the analysis of the temperature dependence of the PL intensity and decay time, we identified a weak back transfer process from Er to the glass host that makes the quenching of the PL intensity weak. Large magnitudes of calculated emission cross-section (σ{sub e}), effective bandwidth (Δλ{sub eff}), and bandwidth quality factor (FWHM × σ{sub e}) relatives to {sup 4}I{sub 13/2} → {sup 4}I{sub 15/2} transition in Er doped Ag0.5 glass have been shown. They indicate that this glass sample has good prospect as a gain medium applied for 1.53 μm band broad and high-gain erbium-doped fiber amplifiers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Long-range ordering of reduced magnetic moments in the spin-gap compound CeOs{sub 2}Al{sub 10} as seen via muon spin relaxation and neutron scattering

We have carried out neutron diffraction, muon spin relaxation ({mu}SR), and inelastic neutron scattering (INS) investigations on a polycrystalline sample of CeOs{sub 2}Al{sub 10} to investigate the nature of the phase transition observed near 29 K in the resistivity and heat capacity. Our {mu}SR data clearly reveal coherent frequency oscillations below 28 K, indicating the presence of an internal field at the muon site, which confirms the long-range magnetic ordering of the Ce moment below 28 K. Upon cooling the sample below 15 K, unusual behavior of the temperature-dependent {mu}SR frequencies may indicate either a change in the muon site, consistent with the observation of superstructure reflections in electron diffraction, or a change in the ordered magnetic structure. Neutron diffraction data do not reveal any clear sign of either magnetic Bragg peaks or superlattice reflections. Furthermore, INS measurements clearly reveal the presence of a sharp inelastic excitation near 11 meV between 5 and 26 K, due to opening of a gap in the spin-excitation spectrum, which transforms into a broad response at and above 30 K. The magnitude of the spin gap (11 meV) as derived from the INS peak position agrees very well with the gap value as estimated from the bulk properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Boundary layer transition↗

Large polarization-dependent exciton optical Stark effect in lead iodide perovskites

A strong interaction of a semiconductor with a below-bandgap laser pulse causes a blue-shift of the bandgap transition energy, known as the optical Stark effect. The energy shift persists only during the pulse duration with an instantaneous response time. The optical Stark effect has practical relevance for applications, including quantum information processing and communication, and passively mode-locked femtosecond lasers. Here we demonstrate that solution-processable lead-halide perovskites exhibit a large optical Stark effect that is easily resolved at room temperature resulting from the sharp excitonic feature near the bandedge. We also demonstrate that a polarized pump pulse selectively shifts one spin state producing a spin splitting of the degenerate excitonic states. Such selective spin manipulation is an important prerequisite for spintronic applications. Lastly, our result implies that such hybrid semiconductors may have great potential for optoelectronic applications beyond photovoltaics.

14 SOLAR ENERGY↗

Structure and properties of the subsolar magnetopause for northward IMF - ISEE observations

This paper describes the structure and the magnetic-field, electric-field, and plasma properties of the ISEE-1 magnetopause crossing on November 5, 1978, which occurred near the subsolar point when the IMF was strongly northward. It was found that the magnetopause was composed of three layers: (1) a sheath transition layer, in which there is a gradual density decrease without a change in temperature and which occurs totally within the magnetosheath plasma; (2) an outer boundary layer, which is dominated by magnetosheath particles; (3) and an inner boundary layer dominated by magnetospheric particles. No significnt heating or cooling was seen across the magnetopause during this crossing. The plasma within each of the layers was quite uniform, and their boundaries were sharp, suggesting that there was very little diffusion present.

Song, P.↗

Hypersonic Separated Flows About "Tick" Configurations With Sensitivity to Model Design

This paper presents computational results obtained by applying the direct simulation Monte Carlo (DSMC) method for hypersonic nonequilibrium flow about "tick-shaped" model configurations. These test models produces a complex flow where the nonequilibrium and rarefied aspects of the flow are initially enhanced as the flow passes over an expansion surface, and then the flow encounters a compression surface that can induce flow separation. The resulting flow is such that meaningful numerical simulations must have the capability to account for a significant range of rarefaction effects; hence the application of the DSMC method in the current study as the flow spans several flow regimes, including transitional, slip, and continuum. The current focus is to examine the sensitivity of both the model surface response (heating, friction and pressure) and flowfield structure to assumptions regarding surface boundary conditions and more extensively the impact of model design as influenced by leading edge configuration as well as the geometrical features of the expansion and compression surfaces. Numerical results indicate a strong sensitivity to both the extent of the leading edge sharpness and the magnitude of the leading edge bevel angle. Also, the length of the expansion surface for a fixed compression surface has a significant impact on the extent of separated flow.

Moss, J. N.↗

Physics and Modeling of Quasi-Steady and Forced Shock Trains

The dual-mode scramjet is a propulsive concept for contemporary hypersonic vehicles promising flight cruise speeds upwards of Mach 5. Despite decades of development and a recent resurgence in interest, such engines are not routinely deployed for commercial or military purposes. Instead, they have been confined to the realm of ground-test research and limited one-off flight test missions. One of the key stumbling blocks on the critical path to deployment of a dual-mode scramjet is the optimal design and stable operation of the isolator, a typically constant area duct that separates the scramjet inlet from the combustor. During ramjet mode at Mach numbers from 3 to 5 and during the transition to scramjet mode at higher Mach numbers, the isolator contains the pseudo-shock. Necessary to meet the back-pressure in the combustor, the pseudo-shock is typically divided into a shock dominated shock train region followed by a turbulence driven mixing region. Fluctuations in combustor pressure due to vehicle maneuvering, throttling, or combustion instabilities drive the shock train to shift streamwise within the isolator. In response to sharp pressure fluctuations, the shock train is unable to stabilize within the isolator, and the scramjet unstarts by ejecting the shock train out the inlet. This work addresses three key gaps in understanding of the isolator pseudo-shock. The phenomenon is studied in three experimental facilities to investigate the quasi-steady and unsteady fluid dynamics of the shock train in fueled and un-fueled test conditions. The strong link between boundary layer morphology and shock train structure is studied in detail and used as a tool to evaluate the state-of-the-art definitions and models of the pseudo-shock. Identifying the limitations of these models, a new process driven flux-conserved pseudo-shock model is proposed. This provides a computationally efficient model grounded in the fluid dynamic mechanisms of the pseudo-shock with better predictive capability than the current state-of-the-art across all facilities tested. The unsteady behavior of the shock train is further investigated to identify and understand two distinct forced dynamic modes: mechanically induced, low-rate forcing and high-rate combustion driven unsteadiness that sheds upstream propagating shocks. The proposed process driven model is found to be effective in the the limiting case of high-rate combustion driven unsteadiness by evaluating the model in a shock stationary reference frame. Further analysis identifies the approximately rigid chain motion of the shock train structure to mechanically induced forcing. The time delay between the onset of forced dynamics is found to saturate to a constant value and maximum shock train speed along the isolator with respect to the perturbation rate of change. The result of this work provides dual-mode scramjet designers with improved tools and physical understanding to develop more efficient, robust, and capable propulsion systems for hypersonic vehicles.

JAXA↗

Emission from quantum-dot high-β microcavities: transition from spontaneous emission to lasing and the effects of superradiant emitter coupling

Measured and calculated results are presented for the emission properties of a new class of emitters operating in the cavity quantum electrodynamics regime. The structures are based on high-finesse GaAs/AlAs micropillar cavities, each with an active medium consisting of a layer of InGaAs quantum dots (QDs) and the distinguishing feature of having a substantial fraction of spontaneous emission channeled into one cavity mode (high β-factor). This paper demonstrates that the usual criterion for lasing with a conventional (low β-factor) cavity, that is, a sharp non-linearity in the input–output curve accompanied by noticeable linewidth narrowing, has to be reinforced by the equal-time second-order photon autocorrelation function to confirm lasing. The article also shows that the equal-time second-order photon autocorrelation function is useful for recognizing superradiance, a manifestation of the correlations possible in high-β microcavities operating with QDs. In terms of consolidating the collected data and identifying the physics underlying laser action, both theory and experiment suggest a sole dependence on intracavity photon number. Evidence for this assertion comes from all our measured and calculated data on emission coherence and fluctuation, for devices ranging from light-emitting diodes (LEDs) and cavity-enhanced LEDs to lasers, lying on the same two curves: one for linewidth narrowing versus intracavity photon number and the other for g( 2 )(0) versus intracavity photon number.

36 MATERIALS SCIENCE↗

Experimental study of disturbances produced in a pre-transitional laminar boundary layer by weak freestream turbulence

The high-amplitude, low-frequency, disturbances generated in a Blasius boundary layer by grid-produced freestream turbulence were studied by means of hot-wire anemometry and by flow visualization. Emphasis was placed on determining the cause and nature of these, and on their effect upon the mean flow profile. It was found that the motion in the layer was intrinsically three-dimensional, according to which the fronts, of Tollmien-Schlichting waves became warped. Evidence of streamwise vorticity was noted. At Reynolds numbers near 1.6 million, the maximum attained, sharp velocity gradients appeared locally. With increase of grid size, there appeared turbulent spots which were wider than the coherence scale of the background motion.

Kendall, J. M.↗

Learning protocols for the fast and efficient control of active matter

Exact analytic calculation shows that optimal control protocols for passive molecular systems often involve rapid variations and discontinuities. However, similar analytic baselines are not generally available for active-matter systems, because it is more difficult to treat active systems exactly. Here we use machine learning to derive efficient control protocols for active-matter systems, and find that they are characterized by sharp features similar to those seen in passive systems. We show that it is possible to learn protocols that effect fast and efficient state-to-state transformations in simulation models of active particles by encoding the protocol in the form of a neural network. We use evolutionary methods to identify protocols that take active particles from one steady state to another, as quickly as possible or with as little energy expended as possible. Our results show that protocols identified by a flexible neural-network ansatz, which allows the optimization of multiple control parameters and the emergence of sharp features, are more efficient than protocols derived recently by constrained analytical methods. Our learning scheme is straightforward to use in experiment, suggesting a way of designing protocols for the efficient manipulation of active matter in the laboratory.

74 ATOMIC AND MOLECULAR PHYSICS↗

Excitation of helium atoms in collisions with plasma electrons in an electric field

The rate constants are evaluated for excitation of helium atoms in metastable states by electron impact if ionized helium is located in an external electric field and is supported by it, such that a typical electron energy is small compared to the atomic excitation energy. Under these conditions, atomic excitation is determined both by the electron traveling in the space of electron energies toward the excitation threshold and by the subsequent atomic excitation, which is a self-consistent process because it leads to a sharp decrease in the energy distribution function of electrons, which in turn determines the excitation rate. The excitation rate constant is calculated for the regimes of low and high electron densities, and in the last case, it is small compared to the equilibrium rate constant where the Maxwell distribution function is realized including its tail. Quenching of metastable atomic states by electron impact results in excitation of higher excited states, rather than transition to the ground electron state for the electric field strengths under consideration. Therefore, at restricted electron number densities, the rate of emission of resonant photons of the wavelength 58 nm, which results from the transition from the 2{sup 1}P state of the helium atom to the ground state, is close to the excitation rate of metastable atomic states. The efficiency of atomic excitation in ionized helium, i.e., the part of energy of an electric field injected in ionized helium that is spent on atomic excitation, is evaluated. The results exhibit the importance of electron kinetics for an ionized gas located in an electric field.

74 ATOMIC AND MOLECULAR PHYSICS↗

Breccia Formation at a Complex Impact Crater: Slate Islands, Lake Superior, Ontario, Canada

The Slate Islands impact structure is the eroded remnant of a approximately 30-32 km-diameter complex impact structure located in northern Lake Superior, Ontario, Canada. Target rocks are Archean supracrustal and igneous rocks and Proterozoic metavolcanics, metasediments, and diabase. A wide variety of breccias occurs on the islands, many of which contain fragments exhibiting shock metamorphic features. Aphanitic, narrow and inclusion-poor pseudotachylite veins, commonly with more or less parallel boundaries and apophyses branching off them, represent the earliest breccias formed during the compression stage of the impact process. Coarse-grained, polymictic elastic matrix breccias form small to very large, inclusion-rich dikes and irregularly shaped bodies that may contain altered glass fragments. These breccias have sharp contacts with their host rocks and include a wide range of fragment types some of which were transported over minimum distances of approximately 2 km away from the center of the structure. They cut across pseudotachylite veins and contain inclusions of them. Field and petrographic evidence indicate that these polymictic breccias formed predominantly during the excavation and central uplift stages of the impact process. Monomictic breccias, characterized by angular fragments and transitional contacts with their host rocks, occur in parautochthonous target rocks, mainly on the outlying islands of the Slate Islands archipelago. A few contain fragmented and disrupted, coarse-grained, polymictic clastic matrix breccia dikes. This is an indication that at least some of these monomictic breccias formed late in the impact process and that they are probably related to a late crater modification stage. A small number of relatively large occurrences of glass-poor, suevitic breccias occur at the flanks of the central uplift and along the inner flank of the outer ring of the Slate Islands complex crater. A coarse, glass-free, allogenic breccia, containing shatter-coned fragments derived from Proterozoic target rocks (upper target strata), observed at two locations may be analogous to the 'Bunt Breccia' of the Ries crater in Germany. At one of these locations this breccia lies close to a crater suevite deposit. At the other, it overlies parautochthonous, monomictic breccia. The State Islands impact breccias are superbly exposed, much better than breccias in most other terrestrial impact structures. Observations, including those indicative of multiple and and sequential processes, provide insight on how impact breccias form and how they relate to the various phases of the impact process. Eventually they will lead to an improved understanding of planetary impact processes.

Dressler, B. O.↗