Search NASA⌕ Search

SEARCH · Search NASA

Results for “vortex generators”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,135 records · Page 63

The Effect of Pulse Length and Ejector Radius on Unsteady Ejector Performance

The thrust augmentation of a set of ejectors driven by a shrouded Hartmann-Sprenger tube has been measured at four different frequencies. Each frequency corresponded to a different length to diameter ratio of the pulse of air leaving the driver shroud. Two of the frequencies had length to diameter ratios below the formation number, and two above. The formation number is the value of length to diameter ratio below which the pulse converts to a vortex ring only, and above which the pulse becomes a vortex ring plus a trailing jet. A three level, three parameter Box-Behnken statistical design of experiment scheme was performed at each frequency, measuring the thrust augmentation generated by the appropriate ejectors from the set. The three parameters were ejector length, radius, and inlet radius. The results showed that there is an optimum ejector radius and length at each frequency. Using a polynomial fit to the data, the results were interpolated to different ejector radii and pulse length to diameter ratios. This showed that a peak in thrust augmentation occurs when the pulse length to diameter ratio equals the formation number, and that the optimum ejector radius is 0.87 times the sum of the vortex ring radius and the core radius.

Wilson, Jack↗

Noise Characteristics of a Four-Jet Impingement Device Inside a Broadband Engine Noise Simulator

The noise generation mechanisms for four directly impinging supersonic jets are investigated employing implicit large eddy simulations with a higher-order accurate weighted essentially non-oscillatory shock-capturing scheme. Impinging jet devices are often used as an experimental apparatus to emulate a broadband noise source. Although such devices have been used in many experiments, a detailed investigation of the noise generation mechanisms has not been conducted before. Thus, the underlying physical mechanisms that are responsible for the generation of sound waves are not well understood. The flow field is highly complex and contains a wide range of temporal and spatial scales relevant for noise generation. Proper orthogonal decomposition of the flow field is utilized to characterize the unsteady nature of the flow field involving unsteady shock oscillations, large coherent turbulent flow structures, and the sporadic appearance of vortex tubes in the center of the impingement region. The causality method based on Lighthill's acoustic analogy is applied to link fluctuations of flow quantities inside the source region to the acoustic pressure in the far field. It will be demonstrated that the entropy fluctuation term in the Lighthill's stress tensor plays a vital role in the noise generation process. Consequently, the understanding of the noise generation mechanisms is employed to develop a reduced-order linear acoustic model of the four-jet impingement device. Finally, three linear acoustic FJID models are used as broadband noise sources inside an engine nacelle and the acoustic scattering results are validated against far-field acoustic experimental data.

Broadband↗

Polar Vortex Outbreak Air Transport: Observation using Satellite IR Sounder Derived Ozone Product and Comparison with Model

The Single Field of View (SFOV) Sounder Atmospheric Products (SiFSAP) derived from Cross-track Infrared Sounder (CrIS) on SNPP and JPSS have a spatial resolution ( ~14.5 km) better than most global weather and climate models. Most recent significant improvement in the quality of these products enables us to use these high-resolution observation-based sounding data for weather studies and model evaluation. The aim of this study is to explore the value to use these SFOV products for studying the dynamic transport associated with polar vortex outbreak. In a few cases studies, we used SiFSAP products, especially ozone, as well as the data of wind, geopotential height (GPH) and potential velocity (PV) from the fifth-generation ECMWF reanalysis (ERA5) data, to analyze the variation of total ozone, relative humidity and ozone in different layers, as well as their correlation with GPH and PV. Some comparison of the retrieved temperature and water vapor with ERA5 data, and ozone with the Ozone Mapping and Profiler Suite (OMPS) measurements have also been made. It is found (1) the transport of O3-riched polar air accompanying the polar vortex breakup to lower latitude and lower atmosphere, and (2) the transport path of O3 agreeing well with the path of polar cold air (illustrated using the retrieved RH, wind fields and GPH). These results demonstrate the 3-D structure of O3 distribution as derived from CrIS measurements provides some insights of the cold air transport, and can be used to track the dynamic transport of polar cold air following the outbreak of polar vortex. The observed enhancement of O3 following the polar vortex outbreak also suggests some possible linkage between the tropospheric cold air advected with stratospheric air source.

Xiaozhen Xiong↗

QUIESCENT PROMINENCE DYNAMICS OBSERVED WITH THE HINODE SOLAR OPTICAL TELESCOPE. I. TURBULENT UPFLOW PLUMES

Hinode/Solar Optical Telescope (SOT) observations reveal two new dynamic modes in quiescent solar prominences: large-scale (20-50 Mm) 'arches' or 'bubbles' that 'inflate' from below into prominences, and smaller-scale (2-6 Mm) dark turbulent upflows. These novel dynamics are related in that they are always dark in visible-light spectral bands, they rise through the bright prominence emission with approximately constant speeds, and the small-scale upflows are sometimes observed to emanate from the top of the larger bubbles. Here we present detailed kinematic measurements of the small-scale turbulent upflows seen in several prominences in the SOT database. The dark upflows typically initiate vertically from 5 to 10 Mm wide dark cavities between the bottom of the prominence and the top of the chromospheric spicule layer. Small perturbations on the order of 1 Mm or less in size grow on the upper boundaries of cavities to generate plumes up to 4-6 Mm across at their largest widths. All plumes develop highly turbulent profiles, including occasional Kelvin-Helmholtz vortex 'roll-up' of the leading edge. The flows typically rise 10-15 Mm before decelerating to equilibrium. We measure the flowfield characteristics with a manual tracing method and with the Nonlinear Affine Velocity Estimator (NAVE) 'optical flow' code to derive velocity, acceleration, lifetime, and height data for several representative plumes. Maximum initial speeds are in the range of 20-30 km s{sup -1}, which is supersonic for a {approx}10,000 K plasma. The plumes decelerate in the final few Mm of their trajectories resulting in mean ascent speeds of 13-17 km s{sup -1}. Typical lifetimes range from 300 to 1000 s ({approx}5-15 minutes). The area growth rate of the plumes (observed as two-dimensional objects in the plane of the sky) is initially linear and ranges from 20,000 to 30,000 km{sup 2} s{sup -1} reaching maximum projected areas from 2 to 15 Mm{sup 2}. Maximum contrast of the dark flows relative to the bright prominence plasma in SOT images is negative and ranges from -10% for smaller flows to -50% for larger flows. Passive scalar 'cork movies' derived from NAVE measurements show that prominence plasma is entrained by the upflows, helping to counter the ubiquitous downflow streams in the prominence. Plume formation shows no clear temporal periodicity. However, it is common to find 'active cavities' beneath prominences that can spawn many upflows in succession before going dormant. The mean flow recurrence time in these active locations is roughly 300-500 s (5-8 minutes). Locations remain active on timescales of tens of minutes up to several hours. Using a column density ratio measurement and reasonable assumptions on plume and prominence geometries, we estimate that the mass density in the dark cavities is at most 20% of the visible prominence density, implying that a single large plume could supply up to 1% of the mass of a typical quiescent prominence. We hypothesize that the plumes are generated from a Rayleigh-Taylor instability taking place on the boundary between the buoyant cavities and the overlying prominence. Characteristics, such as plume size and frequency, may be modulated by the strength and direction of the cavity magnetic field relative to the prominence magnetic field. We conclude that buoyant plumes are a source of quiescent prominence mass as well as a mechanism by which prominence plasma is advected upward, countering constant gravitational drainage.

79 ASTRONOMY AND ASTROPHYSICS↗

Starting vortex, separation bubbles and stall - A numerical study of laminar unsteady flow around an airfoil

The stalling characteristics of an airfoil in a laminar viscous incompressible fluid are investigated. The governing equations in terms of the vorticity and stream function are solved using an implicit finite-difference scheme and point successive relaxation procedure. The development of the impulsively started flow, the initial generation of circulation, and the behavior of the forces at large times are studied. Following the impulsive start, the lift is at first very large and then it rapidly drops. The subsequent growth of circulation and lift is associated with the starting vortex. After incipient separation, the lift increases owing to enlargement of the separation bubble and intensification of the flow rotation in it. The extension of this bubble beyond the trailing edge causes it to rupture and brings about the stalling characteristics of the airfoil. Subsequently, new bubbles are formed near the upper surface of the airfoil and are swept away. The behavior of the lift acting on the airfoil is explained in terms of the strength and sense of these bubbles.

Mehta, U. B.↗

Towards Rocket Engine Components with Increased Strength and Robust Operating Characteristics

High-energy rotating machines, powering liquid propellant rocket engines, are subject to various sources of high and low cycle fatigue generated by unsteady flow phenomena. Given the tremendous need for reliability in a sustainable space exploration program, a fundamental change in the design methodology for engine components is required for both launch and space based systems. A design optimization system based on neural-networks has been applied and demonstrated in the redesign of the Space Shuttle Main Engine (SSME) Low Pressure Oxidizer Turbo Pump (LPOTP) turbine nozzle. One objective of the redesign effort was to increase airfoil thickness and thus increase its strength while at the same time detuning the vane natural frequency modes from the vortex shedding frequency. The second objective was to reduce the vortex shedding amplitude. The third objective was to maintain this low shedding amplitude even in the presence of large manufacturing tolerances. All of these objectives were achieved without generating any detrimental effects on the downstream flow through the turbine, and without introducing any penalty in performance. The airfoil redesign and preliminary assessment was performed in the Exploration Technology Directorate at NASA ARC. Boeing/Rocketdyne and NASA MSFC independently performed final CFD assessments of the design. Four different CFD codes were used in this process. They include WIL DCA T/CORSAIR (NASA), FLUENT (commercial), TIDAL (Boeing Rocketdyne) and, a new family (AardvarWPhantom) of CFD analysis codes developed at NASA MSFC employing LOX fluid properties and a Generalized Equation Set formulation. Extensive aerodynamic performance analysis and stress analysis carried out at Boeing Rocketdyne and NASA MSFC indicate that the redesign objectives have been fully met. The paper presents the results of the assessment analysis and discusses the future potential of robust optimal design for rocket engine components.

Marcu, Bogdan↗

Influence of forebody cross-sectional shape on wing vortex burst location

A water tunnel study examining the influence of forebody cross section on the position of the wing vortex burst was carried out in the NASA Ames-Dryden water tunnel for a 55-deg cropped delta-wing model. Two of three cross sections investigated were chine-shaped, where the included angle of the chine was either 7.5-deg, representing a rather small side-edge angle, or 90 deg, representing a more moderate design. The third cross section was circular and served as a baseline for comparison. It is found that the 7.5 deg chine cross section generated the strongest forebody vortices of the three configurations and that these strong forebody vortices interacted with the main wing vortices in such a manner as to dramatically delay wing vortex burst position at zero sideslip. If the configuration is sideslipped, large asymmetries in wing vortex burst location may result.

Hall, R. M.↗

Josephson currents in neutron stars

We demonstrate that the interface between S-wave and P-wave paired superfluids in neutron stars induces a neutron supercurrent, a charge-neutral analog of the Josephson junction effect in electronic superconductors. The proton supercurrent entrainment by the neutron superfluid generates, in addition to the neutral supercurrent, a charged current across the interface. Beyond this stationary effect, the motion of the neutron vortex lines responding to secular changes in the neutron star’s rotation rate induces a time-dependent oscillating Josephson current across this interface when proton flux tubes are dragged along with them. We show that such motion produces radiation from the interface once clusters of proton flux tubes intersect the interface. The power of radiation exceeds by orders of magnitude the Ohmic dissipation of currents in neutron stars. As a result, this effect appears to be phenomenologically significant enough to heat the star and alter its cooling rate during the photon cooling era.

79 ASTRONOMY AND ASTROPHYSICS↗

Aerodynamic performance of jet-flap wings

Computer program analyzes performance of jet-flap wings. Fast and easy-to-use prediction technique, it generates accurate solutions for wide range of wing geometries and trailing-edge jet momentum distributions. Analysis is based on optimized vortex-lattice approach and results in rapid convergence of both overall and distributed loadings.

Hough, G. R.↗

A cooperative program to stimulate student involvement through the MIT Undergraduate Research Opportunity Program

Flow characteristics in the low speed Wright Brothers Wind Tunnel were studied. Calculations to check the precision of the tunnel were conducted. A program for generating computational grids around an airfoil was developed and compared with the wind tunnel model. Low Reynolds number flow phenomenon of periodic vortex shedding in a wake were also studied by applying a hot-wire anomemeter.

Source record↗

Simulation of unsteady flows through stator and rotor blades of a gas turbine using the Chimera method

A two-dimensional model to solve compressible Navier-Stokes equations for the flow through stator and rotor blades of a turbine is developed. The flow domains for the stator and rotor blades are coupled by the Chimera method that makes grid generation easy and enhances accuracy because the area of the grid that have high turning of grid lines or high skewness can be eliminated from the computational domain after the grids are generated. The results of flow computations show various important features of unsteady flows including the acoustic waves interacting with boundary layers, Karman vortex shedding from the trailing edge of the stator blades, pulsating incoming flow to a rotor blade from passing stator blades, and flow separation from both suction and pressure sides of the rotor blades.

Nakamura, S.↗

Effect of chemical heat release in a temporally evolving mixing layer

Two-dimensional numerical simulations of a temporally evolving mixing layer with an exothermic infinitely fast diffusion flame between two unmixed reactants have been carried out in the limit of zero Mach number to study the effect of the heat release on the early stages of the evolution of the flow. Attention has been directed to relatively large values of the oxidizer-to-fuel mass stoichiometric ratio typical of hydrocarbon flames, and initial vorticity distributions thicker than the temperature and species distributions have been chosen to mimic the situation at the outlet of a jet. The results show that, during the stages of the evolution covered by the present simulations, enhancement of combustion occurs by local stretching of the flame without much augmentation of its area. The rate of product generation depends strongly on the initial conditions, which suggests the possibility of controlling the combustion by acting on the flow. Rollup and vortex amalgamation still occur in these reacting flows but are very much affected by the production of new vorticity by baroclinic torques. These torques lead to counter rotating vortex pairs around the flame and, more importantly, in thin layers of light fluid that leave the vicinity of the flame when the Kelvin-Helmholtz instability begins to develop. Propelled by the vortex pairs, these layers wind around, split on reaching high pressure regions, and originate new vortex pairs in a process that ends up building large-scale vortices with a vorticity distribution more complex than for a constant density fluid.

Higuera, F. J.↗

A Data-Driven Analysis of a Tactical Surface Scheduler

NASA's Airspace Technology Demonstration-2 (ATD-2) integrates arrival, departure, and surface operations to extend integrated traffic sequencing all the way from the gate to the overhead stream and back again for multi-airport, metroplex environments. A key concept of ATD-2 centers on surface scheduling that allows aircraft to taxi, climb, and insert within the overhead stream with minimal interruptions. A core principle is to allow aircraft to absorb delay at the gate prior to engine start in order to reduce overall fuel burn and emissions. To achieve these goals, it is necessary for the scheduler to properly balance the demand at the runway with the available capacity while also predicting accurate takeoff times. This paper provides a data-driven analysis of the runway demand capacity balancing and measures the accuracy of schedules that are generated while running in a live operational environment at the Charlotte Douglas International Airport. We found that using minimum-time wake vortex separation constraints to define runway capacity resulted in scheduling departure operations at a slightly higher rate than the runway was operating and we discovered a surprising relationship between the runway rate and the accuracy of the schedules.

Tactical Surface Scheduler↗

A Data-Driven Analysis of a Tactical Surface Scheduler

NASA's Airspace Technology Demonstration-2 (ATD-2) integrates arrival, departure, and surface operations to extend integrated traffic sequencing all the way from the gate to the overhead stream and back again for multi-airport, metroplex environments. A key concept of ATD-2 centers on surface scheduling that allows aircraft to taxi, climb, and insert within the overhead stream with minimal interruptions. A core principle is to allow aircraft to absorb delay at the gate prior to engine start in order to reduce overall fuel burn and emissions. To achieve these goals, it is necessary for the scheduler to properly balance the demand at the runway with the available capacity while also predicting accurate takeoff times. This paper provides a data-driven analysis of the runway demand capacity balancing and measures the accuracy of schedules that are generated while running in a live operational environment at the Charlotte Douglas International Airport. We found that using minimum-time wake vortex separation constraints to define runway capacity resulted in scheduling departure operations at a slightly higher rate than the runway was operating and we discovered a surprising relationship between the runway rate and the accuracy of the schedules.

Tactical Surface Scheduler↗

Sidelobe Reduction and Mode-Purity Enhancement of Vortex Beams from a Programmable, Rectangular Phased Array Antenna

Tapering the magnitude of the electric field excitation of a programmable, rectangular phased array has been employed to achieve sidelobe reduction and enhancement of mode purity in vortex beams, which carry non-zero orbital angular momentum. Far-field radiation patterns pertaining to a commercial-off-the-shelf, 256-element antenna were generated via electromagnetic simulation. The patterns were decomposed into weighted sums of Laguerre-Gaussian modes. The extracted coupling coefficients were used to gauge mode purity. In comparison to a uniform excitation of the phased array elements, our studies indicate that employing a tapering technique can result in a 10.7 dB reduction of sidelobe power and a 7.22 dB improvement in worst-case, mode-to-mode cross-talk.

orbital angular momentum, phased array, beamformin↗

Application of Particle Image Velocimetry to a Study of Flow About a Multi-Element Airfoil

An experiment was performed on the flap tip vortex shed from a half span Fowler flap. This flap was mounted on a 5 foot span NACA 63(2)-215 Mod B airfoil in the 7 by 10 foot wind tunnel at NASA Ames Research Center. Several noise reduction studies were performed with this model, and the addition of the Particle Image Velocimetry (PIV) research discussed here served as a proof case of large scale PIV. The measurement plane investigated here was a cross plane region. This is cross plane relative to the freestream flow direction. The measurement plane was located at a position 18 inches downstream of the flap trailing edge. This served to prove that measurements could also be made in the more difficult cross plane direction rather than in the downstream flow direction. Lastly the PIV data was used as a practical research tool that yielded important results that could not otherwise be obtained. The flow field area measured was 40 cm by 40 cm square, and served to characterize the downstream flow characteristics of the flap tip vortex under three configurations: the baseline configuration which was the flap and the wing only; the baseline with the addition of a 3/4 span slat; and the baseline with a Flap Edge Device which was designed to reduce the noise generated at the flap. All configurations were tested at a freestream velocity of 64.84 m/s. The test resulted in average velocity fields for the three configurations tested. The velocity fields aided in verifying other testing methods on this particular experiment, and also yielded further insight into the characteristics of the flap tip vortex under the three configurations considered. The velocity data was reduced, and we were able to calculate the vorticity of the flow field. From the position of minimum vorticity the location of the center of the vortex was determined. The circulation was also calculated and aided in comparing the effects of the three configurations on the lifting characteristics of the flap.

Walker, Stephen M.↗

Vortex Domain Walls in Ferroelectrics

Controlling the domain formation in ferroelectric materials at the nanoscale is a fertile ground to explore emergent phenomena and their technological prospects. For example, charged ferroelectric domain walls in BiFeO 3 and ErMnO 3 exhibit significantly enhanced conductivity which could serve as the foundation for next-generation circuits. In this work, we describe a concept in which polar vortices perform the same role as a ferroelectric domain wall in classical domain structures with the key difference being that the polar vortices can accommodate charged (i.e., head-to-head and tail-to-tail) domains, for example, in ferroelectric PbTiO 3 /dielectric SrTiO 3 superlattices. Such a vortex domain wall structure can be manipulated in a reversible fashion under an external applied field.

36 MATERIALS SCIENCE↗

Simulation of three-dimensional incompressible flows with a vortex-in-cell method

A new method for the numerical simulation of three-dimensional incompressible flows is described. The vortex-in-cell (VIC) method presented traces the motion of the vortex filaments in the velocity field which these filaments create. The velocity field is not calculated directly by the Biot-Savart law of interaction but by creating a mesh-record of the vorticity field, then integrating a Poisson's equation via the fast Fourier transform to generate a mesh-record of the velocity field. The computed scales of motion are assumed to be essentially inviscid. Viscous of subgrid-scale effects are incorporated into a filtering procedure in wave vector space. Results of tracing a periodic array of single vortex rings are compared with a Green's function calculation. The agreement is very good.

Couet, B.↗