Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Defect reduction by liquid phase epitaxy of germanium on single-crystalline-like germanium templates on flexible, low-cost metal substrates

Single-crystalline-like germanium (Ge) templates were demonstrated on low-cost, flexible metal substrates and have been used to fabricate III–V materials and devices for photovoltaics and flexible electronics applications. However, these Ge templates, fabricated by magnetron sputtering or plasma enhanced chemical vapor deposition, contain a high density of defects. In order to improve the performance of optoelectronic devices made using the Ge templates, a homo-epitaxial Ge layer has been additionally grown by a liquid phase epitaxy (LPE) method. The LPE Ge layer is composed of significantly larger grains (~26 μm) compared to that of the Ge template (~200 nm). This large size of the LPE Ge grains effectively reduces the volume fraction of grain boundaries. The LPE Ge shows an out-of-plane texture Δω of ~0.63° and an in-plane texture ΔΦ of ~1.26°, which signify improvements of ~39.3% and ~76.6% compared to that of the vapor-deposited Ge template, respectively. Further, the LPE Ge is strain free, compared to the strained Ge template hetero-epitaxially grown on cerium oxide. Defects caused by low-angle grain boundaries, impurities and strain relaxation in the Ge template are found to be suppressed in the LPE Ge. The threading dislocation density is roughly estimated to be ~5 × 10 6 cm -2 in the LPE Ge compared to ~1 × 10 10 cm -2 in the Ge template.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of structural anisotropy on electronic conduction in delafossite tin doped copper indium oxide thin films

Sn doped CuInO{sub 2} thin films having a single delafossite phase have been synthesized by magnetron sputtering technique. A gradual decrease in the activation energy from 0.43 to about 0.10 eV and a large increase in conductivity are observed in Sn doped samples with increasing fraction of crystallites having (006) orientation due to an increase in substrate temperature. Due to thermally activated carrier transport along O-A-O layers and activated carrier generation along BO{sub 6} layers, crystallite orientation becomes a crucial factor in controlling the conduction in delafossite thin films.

36 MATERIALS SCIENCE↗

Microstructural evolution of SiO{sub x} films and its effect on the luminescence of Si nanoclusters

In this paper we demonstrate that the structural and optical properties of Si nanoclusters (Si ncs) formed by thermal annealing of SiO{sub x} films prepared by plasma enhanced chemical vapor deposition (PECVD) and magnetron sputtering are very different. In fact, at a fixed Si excess and annealing temperature, photoluminescence (PL) spectra of sputtered samples are redshifted with respect to PECVD samples, denoting a larger Si ncs size. In addition, PL intensity reaches a maximum in sputtered films at annealing temperatures much lower than those needed in PECVD films. These data are correlated with structural properties obtained by energy filtered transmission electron microscopy and electron energy loss spectroscopy. It is shown that in PECVD films only around 30% of the Si excess agglomerates in clusters while an almost complete agglomeration occurs in sputtered films. These data are explained on the basis of the different initial structural properties of the as-deposited films that become crucial for the subsequent evolution.

36 MATERIALS SCIENCE↗

An extremely high dielectric constant in bismuth-based pyrochlore multilayer film capacitors combined with percolative structure

The percolative film capacitor structure of Pt/Bi{sub 2}Mg{sub 2/3}Nb{sub 4/3}O{sub 7}[BMN(Ar) films deposited at pure argon atmosphere]/Pt was addressed for achievement of a high dielectric constant in the films deposited at room temperature by radio frequency magnetron sputtering. The deterioration of the leakage current characteristics in the percolative capacitor was mitigated using the multilayer films of BMN(O)/BMN(Ar)/BMN(O), where ultrathin BMN(O) films were deposited at a mixed atmosphere of argon and oxygen. An extremely high dielectric constant of 120 and a low leakage current density of 6x10{sup -6} A/cm{sup 2} at 3 V were observed in percolative BMN multilayer films as-deposited at room temperature.

36 MATERIALS SCIENCE↗

Microstructures and the corresponding magnetic properties of half-doped Nd{sub 0.5}Sr{sub 0.5}MnO{sub 3} films

The microstructural and magnetic properties of amorphous, nanoclustered, and self-organized bilayer Nd{sub 0.5}Sr{sub 0.5}MnO{sub 3} films, prepared by rf magnetron sputtering, are investigated. The amorphous film was found to be a typical paramagnet with free motion of the individual Mn spins, and the magnetic properties are well described on the basis of the Curie-Weiss approximation. The nanoclustered film manifests magnetic properties mimicking those of superparamagnetic particles following nonclassical magnetic dynamics. The self-organized bilayer film demonstrates a negative exchange bias typical of a ferromagnet/antiferromagnet hybrid system, in spite of the fact that both layers have a ferromagnetic origin. The magnetic properties of the films are discussed in detail on the basis of modern theoretical models.

36 MATERIALS SCIENCE↗

Alternative to classic annealing treatments for fractally patterned TiO{sub 2} thin films

Titanium dioxide thin films have been deposited by reactive magnetron sputtering on glass and subsequently irradiated by UV radiation using a KrF excimer laser. The influence of the laser fluence (F) on the constitution and microstructure of the deposited films is studied for 0.05<F<0.40 J/cm{sup 2}. The diffraction data reveal that as deposited films are amorphous, while irradiated films present an anatase structure. Additional Raman spectroscopy study shows better crystal quality for the films irradiated with F<0.13 J/cm{sup 2}. The film morphology appears to be strongly modified after laser treatment. Atomic force microscopy and scanning electron microscopy measurements reveal fractally textured films presenting characteristics of high porosity and high specific surface area. Finally, contact angle analysis suggests hydrophobic or wetting behavior depending on F. In order to explain the laser-induced structuration mechanisms, we have successfully applied a fractal as well as the nucleation theories. We propose that electronics effects could be responsible for the observed crystallization.

36 MATERIALS SCIENCE↗

Narrow-band deep-ultraviolet light emitting device using Al{sub 1-x}Gd{sub x}N

We demonstrated mercury-free narrow-band deep-ultraviolet luminescence from field-emission devices with Al{sub 1-x}Gd{sub x}N thin films. The Al{sub 1-x}Gd{sub x}N thin films were grown on fused silica substrates by a radio frequency reactive magnetron sputtering method. The deposited film shows a strong c-axis preferential orientation. A resolution limited, narrow intra-4f luminescence line from Gd{sup 3+} ions has been observed at 315 nm. The luminescence spectrum depends on the growth temperature of the thin film, and the intensity varies as a function of the GdN mole fraction.

36 MATERIALS SCIENCE↗

Carrier concentration dependence of terahertz transmission on conducting ZnO films

With the dc reactive magnetron sputtering method, conducting ZnO thin films with different carrier concentrations on glass substrate were fabricated. The dielectric responses of the ZnO films are characterized with terahertz time-domain spectroscopy. Frequency-dependent conductivity, power absorption, and refractive index are obtained, and the experimental results can be well reproduced with the classic Drude model. Our results reveal that by adjusting the carrier concentration of the ZnO film, the conducting ZnO film can serve as broadband antireflection coatings for substrates and optics in the terahertz frequency range.

36 MATERIALS SCIENCE↗

Surface roughness evolution of nanocomposite thin films

An analysis of dynamic roughening and smoothening mechanisms of thin films grown with pulsed-dc magnetron sputtering is presented. The roughness evolution has been described by a linear stochastic equation, which contains the second- and fourth-order gradient terms. Dynamic smoothening of the growing interface is explained by ballistic effects resulting from impingements of ions to the growing thin film. These ballistic effects are sensitive to the flux and energy of impinging ions. The predictions of the model are compared with experimental data, and it is concluded that the thin film roughness can be further controlled by adjusting waveform, frequency, and width of dc pulses.

36 MATERIALS SCIENCE↗

Structure, conductivity, and transparency of Ga-doped ZnO thin films arising from thickness contributions

Ga-doped ZnO (GZO) films were deposited on amorphous glass substrates at room temperature by radio frequency magnetron sputtering. It is revealed that the influence of deposition parameters, such as target-substrate distance and deposition time, on the structure and properties of the films arises primarily from the variations in film thickness. For the GZO films with smaller thicknesses ({<=}385 nm), crystallinity is greatly improved with an increase in thickness, which leads to an increase in Hall mobility and a decrease in electrical resistivity. The carrier concentration is, however, found to exhibit only a slight change with the thickness variations. The relationship of electrical property and microstructure suggests that the resistivity of the films arises mainly from ionic impurity scattering rather than from grain boundary scattering. All the films exhibit a transmittance of over 90% in the visible wavelength range. The band gap of the GZO films is widened with increasing film thickness. In combination with the result that the carrier concentration exhibited a slight dependence on thicknesses, the broadening of the band gap with thicknesses is attributed more to the improved crystallinity than to the Moss-Burstein shift.

36 MATERIALS SCIENCE↗

Effect of CeO{sub 2} buffer layer on the microstructure and magnetic properties of yttrium iron garnet film on Si substrate

Yttrium iron garnet films were grown by radio frequency magnetron sputtering on Si(111) substrate with and without CeO{sub 2} buffer layer, and influence of CeO{sub 2} buffer on the microstructure and magnetic behaviors of the films were investigated. As compared with the film without buffer, a larger saturation magnetizaton (M{sub s}), lower coercive force (H{sub c}), and higher remnant magnetization (M{sub r}) were obtained due to the introduction of CeO{sub 2} layer. The higher M{sub s} results from the denser structure and the smaller content of Fe{sup 2+} ions. The lower H{sub c} and higher M{sub r} can be explained by the small surface roughness and crystal grains size. The film on CeO{sub 2} buffer layer possess fine microstructure and its surface roughness is smaller than the unbuffered films, which provides an increased exchange between the crystal grains and an enhanced spontaneous magnetization effect, leading to the higher remnant magnetization.

36 MATERIALS SCIENCE↗

WC/a-C nanocomposite thin films: Optical and electrical properties

WC/amorphous carbon (a-C) thin films were deposited by dual magnetron sputtering from individual WC and graphite targets. The influence of film composition and microstructure on the optical and electrical properties was investigated. As evidenced by x-ray photoelectron spectroscopy and grazing angle x-ray diffraction measurements, the WC/a-C films are composite materials made of hexagonal W{sub 2}C and/or cubic {beta}-WC{sub 1-X} nanocrystallites embedded in (a-C) matrix. The optical properties were studied by spectroscopic ellipsometry and the electrical resistivity was measured by the van der Pauw method between 20 and 300 K. Both the optical and the electrical properties of the WC/a-C films are correlated with the chemical composition and microstructure evolution caused by a-C addition. The optical properties of W{sub 2}C/a-C and {beta}-WC{sub 1-x}/a-C films with a-C content {<=}10 at. % are explained by modeling their dielectric functions by a set of Drude-Lorentz oscillators. Further increase in a-C content leads only to the formation of {beta}-WC{sub 1-x}/a-C nanocomposite structures and their optical properties progressively evolve to those of a-C single phase. The electrical resistivity as a function of the temperature of all the films exhibits a negative temperature coefficient of resistivity. Theoretical fitting using the grain-boundary scattering model shows that the transport properties are mainly limited by the grain size and electron mean free path parameters.

36 MATERIALS SCIENCE↗

Thermal conductivity of (Zr,W)N/ScN metal/semiconductor multilayers and superlattices

The cross-plane thermal conductivities of metal/semiconductor multilayers and epitaxial superlattices have been measured as a function of period by time-domain thermoreflectance at room temperature. (001)-oriented ZrN (metal)/ScN (semiconductor) multilayers and (Zr,W)N/ScN epitaxial superlattices with the rocksalt crystal structure were grown on (001)MgO substrates by reactive magnetron sputtering. A distinct minimum in thermal conductivity at a period of {approx}6 nm is observed for ZrN/ScN multilayers. The minimum thermal conductivity of 5.25 W/m K is a factor of {approx}2.7 smaller than the mean of the thermal conductivities (including only the lattice contributions) of the values measured for films of the constituent materials, and approximately equal to the lattice component of the thermal conductivity of a Zr{sub 0.65}Sc{sub 0.35}N alloy film ({approx}5 W/m K). Alloying the ZrN layers with WN{sub x} reduces the lattice mismatch, yielding epitaxial (Zr,W)N/ScN superlattices. The addition of WN{sub x} also reduces the thermal conductivity to {approx}2 W/m K, a value that is sufficiently low to suggest promise for these materials as solid-state thermionic generators.

36 MATERIALS SCIENCE↗

Ferromagnetism of manganese-doped indium tin oxide films deposited on polyethylene naphthalate substrates

Mn-doped indium tin oxide (ITO) films were deposited on polyethylene naphthalate (PEN) substrates using radio-frequency magnetron sputtering. The magnetic, electrical, and optical properties of the films deposited on PEN substrates were investigated by comparing with the properties of films grown on glass substrates at the same growth conditions. Thin films on PEN substrates exhibited low electrical resistivity of the order of 10{sup -4} {omega} cm and high optical transmittance between 75% and 90% in the visible region. Ferromagnetic hysteresis loops were observed at room temperature for the samples grown on PEN substrates. Mn-doped ITO films can be one of the most promising candidates of transparent ferromagnetic materials for flexible spintronic devices.

36 MATERIALS SCIENCE↗

Microfluidic pumps employing surface acoustic waves generated in ZnO thin films

ZnO thin film based surface acoustic wave (SAW) devices have been utilized to fabricate microfluidic pumps. The SAW devices were fabricated on nanocrystalline ZnO piezoelectric thin films deposited on Si substrates using rf magnetron sputtering and use a Sezawa wave mode for effective droplet motion. The as-deposited ZnO surface is hydrophilic, with a water contact angle of {approx}75 deg., which prevents droplet pumping. Therefore, the ZnO surface was coated using a self-assembled monolayer of octadecyltrichlorosilane which forms a hydrophobic surface with a water contact angle of {approx}110 deg. Liquid droplets between 0.5 and 1 {mu}l in volume were successfully pumped on the hydrophobic ZnO surface at velocities up to 1 cm s{sup -1}. Under acoustic pressure, the water droplet on an hydrophilic surface becomes deformed, and the asymmetry in the contact angle at the trailing and leading edges allow the force acting upon the droplet to be calculated. These forces, which increase with input voltage above a threshold level, are found to be in the range of {approx}100 {mu}N. A pulsed rf signal has also been used to demonstrate precision manipulation of the liquid droplets. Furthermore, a SAW device structure is demonstrated in which the ZnO piezoelectric only exists under the input and output transducers. This structure still permits pumping, while avoiding direct contact between the piezoelectric material and the fluid. This is of particular importance for biological laboratory-on-a-chip applications.

36 MATERIALS SCIENCE↗

Ferromagnetic resonance properties and anisotropy of Ni-Mn-Ga thin films of different thicknesses deposited on Si substrate

Ni-Mn-Ga films of different thicknesses were deposited onto Si(100) substrates by magnetron sputtering and annealed at 1073 K for 1 h in high vacuum. X-ray diffraction analysis showed the formation of 220 fiber texture perpendicular to the film plane. Magnetic properties of thin films were investigated at room temperature using ferromagnetic resonance (FMR) technique. The dependencies of both the FMR absorption maximum position and resonance linewidth on the direction of the external magnetic field with respect to the film normal were studied. The data analysis showed that the direction of magnetocrystalline anisotropy easy axis in the films makes 45 deg. angle with the film normal. The modeling allowed evaluation of the uniaxial anisotropy constant, which is found to increase with thickness of Ni-Mn-Ga films. Uniaxial anisotropy constants were found to be {approx}2.8x10{sup 5} erg/cm{sup 3} for 0.1 and 0.5 {mu}m film thickness, {approx}4.2x10{sup 5} erg/cm{sup 3} for 1 {mu}m film, and {approx}5.1x10{sup 5} erg/cm{sup 3} for 3 {mu}m film.

36 MATERIALS SCIENCE↗

Influence of doping (Ti, V, Zr, W) and annealing on the sp{sup 2} carbon structure of amorphous carbon films

The influence of the transition metal (Ti, V, Zr, W) doping on the carbon matrix nanostructuring during the thin film growth and subsequent annealing is investigated. Pure and metal-doped amorphous carbon films (a-C, a-C:Me) were deposited at room temperature by nonreactive magnetron sputtering. The carbon structure of as-deposited and postannealed (up to 1300 K) samples was analyzed by x-ray diffraction (XRD) and Raman spectroscopy. The existence of graphenelike regions in a-C is concluded from a (10) diffraction peak. A comparison of the XRD and Raman results suggests that XRD probes only the small amount of 2-3 nm large graphenelike regions, whereas the majority of the sp{sup 2} phase is present in smaller distorted aromatic clusters which are probed only by Raman spectroscopy. Annealing leads to an increase in the graphene size and the aromatic cluster size. During the carbon film growth the addition of metals enhances ordering of sp{sup 2} carbon in sixfold aromatic clusters compared to a-C; Ti, and Zr showing the strongest effect, W the lowest. This order qualitatively corresponds with the catalytic activity of the respective carbides found during graphitization of carbide-doped graphites published in the literature. With annealing, carbide crystallite formation and growth occurs in a-C:Me films, which destroys the initial carbon structure, reduces the size of the initially formed aromatic clusters and the differences in carbon structure introduced by different dopants. For high annealing temperatures the carbon structure of a-C:Me films is similar to that of a-C, and is determined only by the annealing temperature.

36 MATERIALS SCIENCE↗