Search NASA⌕ Search

SEARCH · Search NASA

Results for “Material point method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Neutron crosstalk between liquid scintillators

We propose a method to quantify the fractions of neutrons scattering between liquid scintillators. Using a spontaneous fission source, this method can be utilized to quickly characterize an array of liquid scintillators in terms of crosstalk. The point model theory due to Feynman is corrected to account for these multiple scatterings. Using spectral information measured by the liquid scintillators, fractions of multiple scattering can be estimated, and mass reconstruction of fissile materials under investigation can be improved. Monte Carlo simulations of mono-energetic neutron sources were performed to estimate neutron crosstalk. A californium source in an array of liquid scintillators was modeled to illustrate the improvement of the mass reconstruction.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

IR studies of the impact of Ge doping on the successive conversion of VO{sub n} defects in Czochralski-Si containing carbon

We report infrared absorption studies of oxygen-related defects in electron-irradiated Ge-doped Czochralski-Si. Our investigation was mainly focused on the reaction channel leading to the formation of VO{sub n} (1{<=}n{<=}6) defects. The VO{sub n} defects form mainly upon annealing, as a result of the successive aggregation of oxygen atoms in the initial VO defect produced by the irradiation: (VO+O{sub i}{yields}VO{sub 2}+O{sub i}{yields}VO{sub 3}+O{sub i}{yields}VO{sub 4},...). It was found that the ratio of the conversion of VO{sub n} to VO{sub n+1} defects is sensitive to the Ge content of the material. In particular, the ratio of the conversion of the VO to the VO{sub 2} defects was found to decrease with the increase in Ge concentration of the samples, although the opposite trend was observed for the VO{sub 3} to VO{sub 4} conversion. However, the VO{sub 2} to VO{sub 3} conversion changes only slightly with Ge content, being practically unaffected for Ge concentrations up to 2x10{sup 20} cm{sup -3}. In the case of VO{sub 2} formation, the phenomenon was attributed to the elastic strains induced in the lattice due to the Ge presence which affects the balance between the reactions VO+O{sub i}{yields}VO{sub 2}, VO+Si{sub I}{yields}O{sub i}, mainly involved in the decay of the VO and the growth of the VO{sub 2} defects. In the case of VO{sub 4} formation, the phenomenon was discussed by taking into account the enhancement of the diffusivity of the O{sub i} atoms in the Ge-doped Si, which could lead to an enhancement of the rate of the reaction VO{sub 3}+O{sub i}{yields}VO{sub 4}. For the VO{sub 3} formation this effect is practically negligible due to the fact that at the temperatures of VO{sub 2} to VO{sub 3} conversion oxygen diffusivity is quite small. The exhibited behavior in the conversion of the VO{sub n} to VO{sub n+1} defects (n=1,2,3) was similar in Ge-doped samples with low carbon content ([C{sub s}]<2x10{sup 16} cm{sup -3}) and in Ge-doped samples with high carbon content ([C{sub s}]{>=}1x10{sup 17} cm{sup -3}). The impact of C as well as its role in the conversion efficiency of VO to VO{sub 2} was studied by comparing the spectra in low carbon and high carbon Ge free Si material. Furthermore, a pair of bands at (1037,1051 cm{sup -1}) was attributed to the VO{sub 5} defect. The origin of another pair of bands (967,1005 cm{sup -1}) was discussed and tentatively correlated with a VO{sub n}C{sub s} structure. The role of Ge and C in the formation of the latter two pairs of bands was discussed.

36 MATERIALS SCIENCE↗

Optoelectronic response and excitonic properties of monolayer MoS{sub 2}

Ab initio, electronic energy bands of MoS{sub 2} single layer are reported within the local density functional approximation. The inclusion of spin orbit coupling reveals the presence of two excitons A and B. We also discuss the change of physical properties of MoS{sub 2} from multilayer and bulk counterparts. The nature of the band gap changes from indirect to direct when the thickness is reduced to a single monolayer. The imaginary and real dielectric functions are investigated. Refractive index and birefringence are also reported. The results suggest that MoS{sub 2} is suitable for potential applications in optoelectronic and photovoltaic devices. The ab initio study is essential to propose the crucial parameters for the analytical model used for A-B exciton properties of the monolayer MoS{sub 2}. From a theoretical point of view, we consider how the exciton behavior evolves under environmental dielectrics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Diffusion in Coulomb crystals

Diffusion in Coulomb crystals can be important for the structure of neutron star crusts. We determine diffusion constants D from molecular dynamics simulations. We find that D for Coulomb crystals with relatively soft-core 1/r interactions may be larger than D for Lennard-Jones or other solids with harder-core interactions. Diffusion, for simulations of nearly perfect body-centered-cubic lattices, involves the exchange of ions in ringlike configurations. Here ions ''hop'' in unison without the formation of long lived vacancies. Diffusion, for imperfect crystals, involves the motion of defects. Finally, we find that diffusion, for an amorphous system rapidly quenched from Coulomb parameter {Gamma}=175 to Coulomb parameters up to {Gamma}=1750, is fast enough that the system starts to crystalize during long simulation runs. These results strongly suggest that Coulomb solids in cold white dwarf stars, and the crust of neutron stars, will be crystalline and not amorphous.

36 MATERIALS SCIENCE↗

Tissue equivalency of phantom materials for neutron dosimetry in proton therapy

Purpose: Previous Monte Carlo and experimental studies involving secondary neutrons in proton therapy have employed a number of phantom materials that are designed to represent human tissue. In this study, the authors determined the suitability of common phantom materials for dosimetry of secondary neutrons, specifically for pediatric and intracranial proton therapy treatments. Methods: This was achieved through comparison of the absorbed dose and dose equivalent from neutrons generated within the phantom materials and various ICRP tissues. The phantom materials chosen for comparison were Lucite, liquid water, solid water, and A150 tissue equivalent plastic. These phantom materials were compared to brain, muscle, and adipose tissues. Results: The magnitude of the doses observed were smaller than those reported in previous experimental and Monte Carlo studies, which incorporated neutrons generated in the treatment head. The results show that for both neutron absorbed dose and dose equivalent, no single phantom material gives agreement with tissue within 5% at all the points considered. Solid water gave the smallest mean variation with the tissues out of field where neutrons are the primary contributor to the total dose. Conclusions: Of the phantom materials considered, solid water shows best agreement with tissues out of field.

61 RADIATION PROTECTION AND DOSIMETRY↗

Least squares parameter estimation methods for material decomposition with energy discriminating detectors

Purpose: Energy resolving detectors provide more than one spectral measurement in one image acquisition. The purpose of this study is to investigate, with simulation, the ability to decompose four materials using energy discriminating detectors and least squares minimization techniques. Methods: Three least squares parameter estimation decomposition techniques were investigated for four-material breast imaging tasks in the image domain. The first technique treats the voxel as if it consisted of fractions of all the materials. The second method assumes that a voxel primarily contains one material and divides the decomposition process into segmentation and quantification tasks. The third is similar to the second method but a calibration was used. The simulated computed tomography (CT) system consisted of an 80 kVp spectrum and a CdZnTe (CZT) detector that could resolve the x-ray spectrum into five energy bins. A postmortem breast specimen was imaged with flat panel CT to provide a model for the digital phantoms. Hydroxyapatite (HA) (50, 150, 250, 350, 450, and 550 mg/ml) and iodine (4, 12, 20, 28, 36, and 44 mg/ml) contrast elements were embedded into the glandular region of the phantoms. Calibration phantoms consisted of a 30/70 glandular-to-adipose tissue ratio with embedded HA (100, 200, 300, 400, and 500 mg/ml) and iodine (5, 15, 25, 35, and 45 mg/ml). The x-ray transport process was simulated where the Beer-Lambert law, Poisson process, and CZT absorption efficiency were applied. Qualitative and quantitative evaluations of the decomposition techniques were performed and compared. The effect of breast size was also investigated. Results: The first technique decomposed iodine adequately but failed for other materials. The second method separated the materials but was unable to quantify the materials. With the addition of a calibration, the third technique provided good separation and quantification of hydroxyapatite, iodine, glandular, and adipose tissues. Quantification with this technique was accurate with errors of 9.83% and 6.61% for HA and iodine, respectively. Calibration at one point (one breast size) showed increased errors as the mismatch in breast diameters between calibration and measurement increased. A four-point calibration successfully decomposed breast diameter spanning the entire range from 8 to 20 cm. For a 14 cm breast, errors were reduced from 5.44% to 1.75% and from 6.17% to 3.27% with the multipoint calibration for HA and iodine, respectively. Conclusions: The results of the simulation study showed that a CT system based on CZT detectors in conjunction with least squares minimization technique can be used to decompose four materials. The calibrated least squares parameter estimation decomposition technique performed the best, separating and accurately quantifying the concentrations of hydroxyapatite and iodine.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

An Agile Design-to-Simulation Workflow Using a New Conforming Moving Least Squares Method

This report summarizes the accomplishments and challenges of a two year LDRD effort focused on improving design-to-simulation agility. The central bottleneck in most solid mechanics simulations is the process of taking CAD geometry and creating a discretization of suitable quality, i.e., the "meshing" effort. This report revisits meshfree methods and documents some key advancements that allow their use on problems with complex geometries, low quality meshes, nearly incompressible materials or that involve fracture. The resulting capability was demonstrated to be an effective part of an agile simulation process by enabling rapid discretization techniques without increasing the time to obtain a solution of a given accuracy. The first enhancement addressed boundary-related challenges associated with meshfree methods. When using point clouds and Euclidean metrics to construct approximation spaces, the boundary information is lost, which results in low accuracy solutions for non-convex geometries and mate rial interfaces. This also complicates the application of essential boundary conditions. The solution involved the development of conforming window functions which use graph and boundary information to directly incorporate boundaries into the approximation space.

42 ENGINEERING↗

Ceramics Analysis and Reliability Evaluation of Structures (CARES). Users and programmers manual

This manual describes how to use the Ceramics Analysis and Reliability Evaluation of Structures (CARES) computer program. The primary function of the code is to calculate the fast fracture reliability or failure probability of macroscopically isotropic ceramic components. These components may be subjected to complex thermomechanical loadings, such as those found in heat engine applications. The program uses results from MSC/NASTRAN or ANSYS finite element analysis programs to evaluate component reliability due to inherent surface and/or volume type flaws. CARES utilizes the Batdorf model and the two-parameter Weibull cumulative distribution function to describe the effect of multiaxial stress states on material strength. The principle of independent action (PIA) and the Weibull normal stress averaging models are also included. Weibull material strength parameters, the Batdorf crack density coefficient, and other related statistical quantities are estimated from four-point bend bar or unifrom uniaxial tensile specimen fracture strength data. Parameter estimation can be performed for single or multiple failure modes by using the least-square analysis or the maximum likelihood method. Kolmogorov-Smirnov and Anderson-Darling goodness-of-fit tests, ninety percent confidence intervals on the Weibull parameters, and Kanofsky-Srinivasan ninety percent confidence band values are also provided. The probabilistic fast-fracture theories used in CARES, along with the input and output for CARES, are described. Example problems to demonstrate various feature of the program are also included. This manual describes the MSC/NASTRAN version of the CARES program.

Nemeth, Noel N.↗

Modeling of Ternary Element Site Substitution in NiAl

It is well recognized that ternary alloying additions can have a dramatic impact on the behavior of ordered intermetallic alloys such as nickel aluminides. Properties as diverse as yield strength, fracture strength, fracture mode, cyclic oxidation resistance, creep strength, and thermal and electrical diffusivity can change by orders of magnitude when a few percent or less of a ternary element is added. Yet our understanding of the resulting point defect structures and the simple site preferences of ternary alloying additions is poor because these are extremely difficult characteristics to determine. This disconnection between the understanding of the structure and properties in ordered alloys is at least in part responsible for the limited development and commercialization of these materials. Theoretical methods have provided useful but limited insight in this area, since most techniques suffer from constraints in the type of elements and the crystallographic structures that can be modeled. In an effort to overcome these limitations, the Bozzolo-Ferrante-Smith (BFS) method for alloys was designed. After a brief description of this approximate quantum mechanical approach, we use BFS to investigate the energetics of Si, Ti, V, Cr, Fe, Co, Cu, Zr, Nb, Mo, Ru, Hf, Ta and W additions to B2-ordered, stoichiometric NiAl. In addition to determining the site preference for these alloying additions over a range of compositions, we include results for the concentration dependence of the lattice parameter. In this introductory paper, we performed our analyses in the absence of constitutional and thermal vacancies for alloys of the form Ni50(Al,X)50. Where data exist, a comparison between experimental, theoretical, and BFS results is also included.

Bozzolo, Guillermo↗

Neutralization of Hydroxide Ion in Melt-Grown NaCl Crystals

Many recent studies of solid-state phenomena, particularly in the area of crystal imperfections, have involved the use of melt-grown NaCl single crystals. Quite often trace impurities in these materials have had a prominent effect on these phenomena. Trace amounts of hydroxide ion have been found in melt-grown NaCl crystals. This paper describes a nondestructive method of neutralizing the hydroxide ion in such crystals. Crystals of similar hydroxide content are maintained at an elevated temperature below the melting point of NaCl in a flowing atmosphere containing. dry hydrogen chloride. Heat treatment is continued until an analysis of the test specimens shows no excess hydroxide ion. A colorimetric method previously described4 is used for this analysis.

Otterson, Dumas A.↗

Print-Consistency and Process-Interaction for Inkjet-Printed Copper on Flexible Substrate

Printed electronics is a fastest growing and emerging technology that have shown much potential in several industries including automotive, wearables, healthcare, and aerospace. Its applications can be found not only in flexible but also in large area electronics. The technology provides an effective and convenient method to additively deposit conductive and insulating materials on any type of substrate. Comparing with traditional manufacturing processes, which involves chemical etching, this technology also comes to be relatively environmental friendly. Despite its status, it is not without its challenges. Starting from the material being compatible in the printer equipment to the point of achieving fine resolutions, and with excellent properties are some of the challenges that printed electronics face. Among the myriad of printing technologies such as Aerosol Jet, micro-dispensing, gravure printing, screen printing, Inkjet printing, Inkjet has gained much attention due to its low-cost, low material consumption, and roll-to-roll capability for mass manufacturing. The technology has been widely used in home and office, but recently gained interest in printed electronics in a research and development setting. Conductive materials used in Inkjet printing generally comprises of metal Nanoparticles that need to be thermally sintered for it to be conductive. The preferred metal of choice has been mostly silver due to its excellent electrical properties and ease in sintering. However, silver comes to be expensive than its counterpart copper. Since copper is prone to oxidation, much focus has been given towards photonic sintering that involves sudden burst of pulsed light at certain energy to sinter the copper Nanoparticles. With this technique, only the printed material gets sintered in a matter of seconds without having a great impact on its substrate, due to which it is also preferred in low temperature applications. With all the knowledge, there is still a large gap in the process side with copper where it is important to look how the print process affects the resolution of the print along with the effect of post-print processes on electrical and mechanical properties. In this paper, a copper Inkjet ink is utilized for understanding the effect of Inkjet print parameters on the ejected droplet and its resolution. Post-print process is also quantified using a photonic sintering equipment for excellent electrical and mechanical properties. To demonstrate the complete process, commercial-off-the-shelf components will also be mounted on the additively printed pads via Inkjet. Statistically, control charting technique will be utilized to understand the capability of the Inkjet process.

printed electronics↗

2010 Defects in Semiconductors GRC

Continuing its tradition of excellence, this Gordon Conference will focus on research at the forefront of the field of defects in semiconductors. The conference will have a strong emphasis on the control of defects during growth and processing, as well as an emphasis on the development of novel defect detection methods and first-principles defect theories. Electronic, magnetic, and optical properties of bulk, thin film, and nanoscale semiconductors will be discussed in detail. In contrast to many conferences, which tend to focus on specific semiconductors, this conference will deal with point and extended defects in a broad range of electronic materials. This approach has proved to be extremely fruitful for advancing fundamental understanding in emerging materials such as wide-band-gap semiconductors, oxides, sp{sup 2} carbon based-materials, and photovoltaic/solar cell materials, and in understanding important defect phenomena such as doping bottleneck in nanostructures and the diffusion of defects and impurities. The program consists of about twenty invited talks and a number of contributed poster sessions. The emphasis should be on work which has yet to be published. The large amount of discussion time provides an ideal forum for dealing with topics that are new and/or controversial.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

System and process for ultrasonic characterization of deformed structures

Generally speaking, the method of the present invention is performed by making various ultrasonic scans at preselected orientations along the length of a material being tested. Data from the scans are then plotted together with various calculated parameters that are calculated from this data. Lines or curves are then fitted to the respective plotted points. Review of these plotted curves allows the location and severity of defects within these sections to be determined and quantified. With this information various other decisions related to how, when or whether repair or replacement of a particular portion of a structure can be made.

36 MATERIALS SCIENCE↗

A modified moment-fitted integration scheme for X-FEM applications with history-dependent material data

Here, we present a strategy for the numerical integration of partial elements with the eXtended finite element method (X-FEM). The new strategy is specifically designed for problems with propagating cracks through a bulk material that exhibits inelasticity. Following a standard approach with the X-FEM, as the crack propagates into new regions of the domain, elements are split into several copies that contain pieces of the domain on either side of the crack. We examine quadrature rules that have sufficient accuracy to calculate stiffness matrices regardless of the orientation of the crack with respect to the element. This permits the number of integration points within elements to remain constant as a crack propagates, and for state data to be easily transferred between successive discretizations. In order to maintain weights that are strictly positive, we propose an approach that blends moment-fitted weights with volume-fraction based weights. To demonstrate the efficacy of this simple approach, we present results from numerical tests and examples with both elastic and plastic material response.

42 ENGINEERING↗

Hydrogen adsorption on decorated graphyne and its analogous with Na

Highlights: • Structural stability of Na decorated single- and double- sided graphyne and its analogous. • Hydrogen storage capacity of decorated graphyne and its analogous, based on Density Functional Theory (DFT) by PBEsol, vdW-DF2-B86R and vdW-DF2 approximations. • Electrical properties like density of states and band gap after Na decoration and hydrogen adsorption. - Abstract: In this paper, we have addressed the structural stability and hydrogen storage capability of single side and double side Na-decorated γ-Graphyne, Graphyne-like Boron Nitride and CCBN-yne, using three methods of density functional theory approximation: PBEsol, vdW-DF2-B86R and vdW-DF2. We also investigated the electronic properties of these structures, decorated by Na atoms and adsorbing hydrogen, such as density of states and band structure. Our results showed that hydrogen can be adsorbed up to three molecules per Na atom. We found the optimal geometries of adsorbed hydrogen molecules on adsorption candidates. We also found that Direct band-gap at “M” point changes after decoration and adsorption in mentioned structures. Finally, we explored metallic structures for hydrogen storage which can be used in the industry of fuel cells.

36 MATERIALS SCIENCE↗

Use of aluminum oxide as a permeation barrier for producing thin films on aluminum substrates

Aluminum has desirable characteristics of good thermal properties, good electrical characteristics, good optical properties, and the characteristic of being nonmagnetic and having a low atomic weight (26.98 g atoms), but because of its low melting point (660 °C) and ability as a reactive metal to alloy with most common metals in use, it has been ignored as a substrate material for use in processing thin films. The author developed a simple solution to this problem, by putting a permeation barrier of alumina (Al{sub 2}O{sub 3}) onto the surface of pure Al substrates by using a standard chemical oxidation process of the surface (i.e., anodization), before additional film deposition of reactive metals at temperatures up to 500 °C for 1-h, without the formation of alloys or intermetallic compounds to affect the good properties of Al substrates. The chromic acid anodization process used (MIL-A-8625) produced a film barrier of ∼(500–1000) nm of alumina. The fact that refractory Al{sub 2}O{sub 3} can inhibit the reaction of metals with Al at temperatures below 500 °C suggests that Al is a satisfactory substrate if properly oxidized prior to film deposition. To prove this concept, thin film samples of Cr, Mo, Er, Sc, Ti, and Zr were prepared on anodized Al substrates and studied by x-ray diffraction, Rutherford ion back scattering, and Auger/argon sputter surface profile analysis to determine any film substrate interactions. In addition, a major purpose of our study was to determine if ErD{sub 2} thin films could be produced on Al substrates with fully hydrided Er films. Thus, a thin film of ErD{sub 2} on an anodized Al substrate was prepared and studied, with and without the alumina permeation barrier. Films for study were prepared on 1.27 cm diameter Al substrates with ∼500 nm of the metals studied after anodization. Substrates were weighed, cleaned, and vacuum fired at 500 °C prior to use. The Al substrates were deposited using standard electron beam cold crucible evaporation techniques, and after deposition the Er film was hydrided with D{sub 2} gas using a standard nonair exposure hydriding technique. All processing was conducted in an all metal ion pumped ultrahigh vacuum system. Results showed that e-beam deposition of films studied onto Al substrates could be successfully performed, if a permeation barrier of Al{sub 2}O{sub 3} from 500 to 1000 nm was made prior to thin film deposition up to temperatures of 500 °C for 1-h. Hydrides also, could be produced with full gas/metal atomic ratios of ∼2.0 as evidenced by the ErD{sub 2} films produced. Thus, the use of a simple permeation barrier of Al{sub 2}O{sub 3} on Al substrates prior to additional metal film deposition was proven to be a successful method of producing both thin metal films and hydride films of various types for many applications.

36 MATERIALS SCIENCE↗

Predicting Melt Curves of Energetic Materials Using Molecular Models

Here, in this work, the solid–liquid coexistence curves of classical fully flexible atomistic models of α-RDX and β-HMX were calculated using thermodynamically rigorous methodologies that identify where the free energy difference between the phases is zero. The free energy difference between each phase at a given state point was computed using the pseudosupercritical path (PSCP) method, and Gibbs–Helmholtz integration was used to evaluate the solid–liquid free energy difference as a function of temperature. This procedure was repeated for several pressures to determine points along the coexistence curve, which were then fit to the Simon–Glatzel functional form. While effective, this method is computationally expensive. An alternative approach is to compute the melting point at a single pressure via the PSCP method, and then use the Gibbs–Duhem integration technique to trace out the coexistence curve in a more computationally economical manner. Both approaches were used to determine the coexistence curve of α-RDX. The Gibbs–Duhem integration method was shown to generate a melt curve that is in good agreement with the PSCP-derived melt curve, while only costing ~10 % of the computational resources used for the PSCP method. For α-RDX, the predicted melting temperature increases significantly more for a given increase in pressure when compared to available experimental data.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Is organic photovoltaics promising for indoor applications?

This work utilizes organic photovoltaics (OPV) for indoor applications, such as powering small electronic devices or wireless connected Internet of Things. Three representative polymer-based OPV systems, namely, poly(3-hexylthiophene-2,5-diyl), poly[N-9′-heptadecanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′, 1′,3′-benzothiadiazole)], and poly[[4,8-bis[(2-ethylhexyl)oxy]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl] [3-fluoro-2-[(2-ethylhexyl)carbonyl]thieno[3,4-b]thiophenediyl]], were selected as the donor materials in blend with fullerene derivatives for comparison under low light level condition using fluorescent lamps. PCDTBT based devices are found to be the best performing system, generating 13.9 μW/cm{sup 2} corresponding to 16.6% power conversion efficiency at 300 lx, although PTB7 based devices show the highest efficiency under one sun conditions. This high performance suggests that OPV is competitive to the other PV technologies under low light condition despite much lower performance under one sun condition. Different properties of these devices are studied to explain the competitive performance at low light level. A low energy consuming method for maximum power point tracking is introduced for the operation of the OPV devices. Finally, a 14 cm × 14 cm OPV module with 100 cm{sup 2} active area is demonstrated for real applications. These findings suggest that OPV, in particular, PCDTBT based devices, could be a promising candidate for indoor applications.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗