Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES, FLAT - STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Numerical solutions of the Navier-Stokes equations for the supersonic laminar flow over a two-dimensional compression corner

Numerical solutions have been obtained for the supersonic, laminar flow over a two-dimensional compression corner. These solutions were obtained as steady-state solutions to the unsteady Navier-Stokes equations using the finite difference method of Brailovskaya, which has second-order accuracy in the spatial coordinates. Good agreement was obtained between the computed results and wall pressure distributions measured experimentally for Mach numbers of 4 and 6.06, and respective Reynolds numbers, based on free-stream conditions and the distance from the leading edge to the corner. In those calculations, as well as in others, sufficient resolution was obtained to show the streamline pattern in the separation bubble. Upstream boundary conditions to the compression corner flow were provided by numerically solving the unsteady Navier-Stokes equations for the flat plate flow field, beginning at the leading edge. The compression corner flow field was enclosed by a computational boundary with the unknown boundary conditions supplied by extrapolation from internally computed points.

Carter, J. E.↗

Discrete sonic jets used as boundary-layer trips at Mach numbers of 6 and 8.5

The effect of discrete three-dimensional sonic jets used to promote transition on a sharp-leading-edge flat plate at Mach numbers of 6 and 8.5 and unit Reynolds numbers as high as 2.5 x 100,000 per cm in the Langley 20-inch hypersonic tunnels is discussed. An examination of the downstream flow-field distortions associated with the discrete jets for the Mach 8.5 flow was also conducted. Jet trips are found to produce lengths of turbulent flow comparable to those obtained for spherical-roughness-element trips while significantly reducing the downstream flow distortions. A Reynolds number based upon secondary jet penetration into a supersonic main flow is used to correlate jet-trip effectiveness just as a Reynolds number based upon roughness height is used to correlate spherical-trip effectiveness. Measured heat-transfer data are in agreement with the predictions.

Stone, D. R.↗

The interaction of moderately strong shock waves with thick perforated walls of low porosity

A theoretical prediction is given of the flow through thick perforated walls of low porosity resulting from the impingement of a moderately strong traveling shock wave. The model was a flat plate positioned normal to the direction of the flow. Holes bored in the plate parallel to the direction of the flow provided nominal hole length-to-diameter ratios of 10:1 and an axial porosity of 25 percent of the flow channel cross section. The flow field behind the reflected shock wave was assumed to behave as a reservoir producing a quasi-steady duct flow through the model. Rayleigh and Fanno duct flow theoretical computations for each of three possible auxiliary wave patterns that can be associated with the transmitted shock (to satisfy contact surface compatibility) were used to provide bounding solutions as an alternative to the more complex influence coefficients method. Qualitative and quantitative behavior was verified in a 1.5- by 2.0-in. helium shock tube. High speed Schlieren photography, piezoelectric pressure-time histories, and electronic-counter wave speed measurements were used to assess the extent of correlation with the theoretical flow models. Reduced data indicated the adequacy of the bounding theory approach to predict wave phenomena and quantitative response.

Grant, D. J.↗

Turbulent boundary-layer velocity profiles on a nonadiabatic at Mach number 6.5

Velocity profiles were obtained from pitot-pressure and total-temperature measurements within a turbulent boundary layer on a large sharp-edged flat plate. Momentum-thickness Reynolds number ranged from 2590 to 8860 and wall-to-adiabatic-wall temperature ratios ranged from 0.3 to 0.5. Measurements were made both with and without boundary layer trips. Five methods are evaluated for correlating the measured velocity profiles with the incompressible law-of-the-wall and the velocity defect law. The mixing-length generalization of Van Driest gives the best correlation.

Keener, E. R.↗

An experimental investigation of a cold jet emitting from a body of revolution into a subsonic free stream

An experimental program was undertaken to determine the pressure distribution induced on aerodynamic bodies by a subsonic cold jet exhausting normal to the body surface and into a subsonic free stream. The investigation was limited to two bodies with single exhaust jets a flat plate at zero angle of attack with respect to the free-stream flow and a cylinder, fitted with a conical nose, with the longitudinal axis alined with the free-stream flow. Experimental data were obtained for free-stream velocity to jet velocity ratios between 0.3 and 0.5. The experimental data are presented in tabular form with appropriate graphs to indicate pressure coefficient contours, pressure coefficient decay, pitching-moment characteristics, and lift characteristics.

Ousterhout, D. S.↗

Autorotating wings - An experimental investigation.

The autorotation of a flat plate about its spanwise axis was experimentally studied. Most of the work was done with a wing mounted in a 5 x 7 ft low-speed wind tunnel. The measurements consisted of the unsteady lift, drag, angular acceleration and the wing rotation rate. The flow pattern was very different from that over a static wing. The maximum and average lift, drag and angular acceleration were measured for Reynolds numbers from 25,000 to 250,000. The effect of applying driving and retarding torques to the wing was studied. A variety of wing configurations were tested, together with freely falling wings. For Reynolds numbers above 4000 the average lift and drag coefficients were comparable to those observed in the fixed axis tests, and it appeared that the flow pattern was similar.

Smith, E. H.↗

A theoretical and experimental investigation of the hypersonic turbulent boundary layer subject to normal and longitudinal pressure gradients and cross flow along a windward plane of symmetry.

A theoretical and experimental investigation for the hypersonic turbulent boundary layer undergoing both normal and longitudinal pressure gradients and cross flow along the plane of symmetry on the windward side of a body of revolution is presented. The purpose of this investigation is to provide a method for calculating boundary layers that occur on the centerline of symmetry of an inlet. The three-dimensional compressible integral equations are written along the symmetry plane and integrated numerically, and the effect of the cross flow on the behavior of the boundary layer is also studied. The experiments were performed at Mach number 6 and Reynolds number of 44,000,000/ft for the axisymmetric case and for the case with cross flow. The velocity profiles and the boundary layer parameters agree relatively well with theoretical values with and without cross flow effects. The presence of the cross flow alters significantly the value of the profiles. Total temperature-velocity correlations deviate from the linear Crocco distribution. Heat transfer rates agree with theoretical values and values obtained by the flat plate reference enthalpy method. Cross flow influence on the heat transfer rates is of minor relevance.

Zakkay, V.↗

A method for integrating the boundary-layer equations through a region of reverse flow.

Development of a procedure for numerically integrating the boundary-layer equations through a region of reverse flow which takes downstream influence into account. This method is applied to the problem of uniform flow past a parallel flat plate of finite length whose surface has a constant velocity directed opposite to that of the main stream. Although singularities occur at both the point of detachment (x sub s) and reattachment (x sub r) of the psi = 0 streamline, this integration technique provides a solution which ceases to apply only in the close proximity of these singular points. From this solution it is evident that, throughout a large portion of the separated region, the flow is strongly affected by conditions near x sub r, thereby demonstrating the importance of allowing information to be transmitted upstream in a region of backflow. Near x sub s, however, it is found that, in spite of the presence of reverse flow, the solution has a self-similar form in this particular example.

Klemp, J. B.↗

Heat transfer by condensation of low pressure metal vapors.

The film condensation of low pressure metal vapors on isothermal vertical flat plates or tubes is considered. The liquid film is treated as a thin layer in which the acceleration and pressure forces are negligible and across which the temperature distribution is linear. The average behavior of the vapor is found from the linearized one-dimensional vapor flow equations. In order to calculate the rate of condensation, a consistent distribution function for the vapor particles at the liquid-vapor interface is necessary and is determined. The result of the analysis is a set of algebraic equations from which one can predict the condensation rate of low pressure metal vapors. A large but continuous temperature decrease in the vapor is predicted and calculated.

Huang, Y. S.↗

Electron density measurements of an inhomogeneous plasma using millimeter wave Fabry-Perot interferometers.

The electron density of a laboratory generated inhomogeneous plasma was measured using 60-90, GHz flat-plate and 150 GHz semi-confocal Fabry-Perot interferometers. The plasma was a negative glow-type and had a measured parabolic electron density profile. An analytical comparison between the derived equations of electron density for an assumed homogeneous plasma slab and an inhomogeneous plasma with parabolic distribution showed that the slab approximation was valid for such a profile. Comparison of measured values of electron density with those using X-band and K-band interferometers for the same plasma indicated good agreement.

Kendall, B. M.↗

Measurements of skin friction on the wall of a hypersonic nozzle.

Direct skin friction measurements obtained on the wall of a Mach 19.8 nozzle are presented. These measurements of skin friction and values deduced from the profile data are compared with predictions from a finite difference theory and also with several 'flat-plate' prediction methods for skin friction.

Harvey, W. D.↗

Diffusion welding tool

Tool allows flat plate diffusion welding to be done in standard brazing furnace. Weld is achieved using high water pressure applied by hand-operated positive-displacement pump. Good welds have been obtained between nickel and nickel-base alloy plates at temperature of 1200 K and water pressure of 13.8 million N/sq m.

Milam, T. B.↗

Charts for predicting turbulent skin friction from the Van Driest method (2)

Charts are presented for rapidly estimating local or average turbulent skin friction on flat plates from Reynolds numbers, based on either length or momentum thickness. These charts facilitate the conversion from one Reynolds number to the other. Ranges of variables covered are: Mach number, 0 to 10; length Reynolds number, 10 to the 5th to 10 to the 9th power; and wall-to-adiabatic-wall temperature ratio, 0.2 to 1.0.

Hopkins, E. J.↗

An analytical solution for the squeeze film between a nondeformable sphere and groove

An analysis is presented to compute the film thickness, pressure and load relations between a rigid ball and rigid groove in normal approach when lubricated by a fluid with an exponential pressure-viscosity relationship. The geometry of the ball-groove system is reduced to the equivalent system of a paraboloid approaching a flat plate. Exact and approximate solutions are presented for the load and pressure relations. There is found to be a limiting load for a given geometry and lubricant regardless of the rate of approach.

Allen, C. W.↗

Protuberance heating test program

Results are presented of the protuberance heating test program. Four general protuberance shapes on a flat plate were tested. Presentation and evaluation of the data both on the protuberance and in the wake regions are made. The test program is an extension of the general protuberance heat transfer test. The additional series of tests was conducted to define the extent of wake heating and to assess the effects of Reynolds number variation on heating both on and around the protuberances. The protuberance models were mounted near the forward end of a six-foot instrumented test plate with stringers that simulated interstage and skirt structure of the Saturn S-4B stage. The tests were performed at Mach numbers of 2.49, 3.51, and 4.44. Reynolds numbers per foot of 3 million and 1.5 million were used for the two lower Mach numbers and 3 million for a Mach number of 4.44. The test Mach numbers simulated the Saturn S-4B flight conditions during the most severe aerodynamic heating period. The test Reynolds numbers were somewhat higher than the flight values, but lower values could not be used because of tunnel and instrumentation limitations. Oil flow runs were made on two representative models at various combinations of Mach number and Reynolds number to help define the extent of wake heating.

Sieker, W. D.↗

Analysis of unsteady thermal boundary layers

The velocity and temperature distribution in an unsteady thermal boundary layer is analyzed by an approximate integral method. The case of a flat plate in a free stream having small harmonic velocity oscillations about a steady mean value is treated in detail. The resulting velocity profiles agree with the available experimental data. These profiles are used to predict the thermal convection when the plate and the stream are at constant but different temperature levels. The flow oscillations cause harmonic temperature oscillations plus a small steady feedback effect which reduces the mean heat transfer to the plate. The amount of decrease is represented by a single coefficient, which is presented graphically.

Miller, R. W.↗

An experimental investigation of turbulent boundary layers at high Mach number and Reynolds numbers

Skin friction, heat transfer and pressure measurements were obtained in laminar, transitional and turbulent boundary layers on flat plates at Mach numbers from 7 to 13 at wall-to-free stream stagnation temperature ratios from 0.1 to 0.3. Measurements in laminar flows were in excellent agreement with the theory of Cheng. Correlations of the transition measurements with measurements on flight vehicles and in ballistic ranges show good agreement. Our transition measurements do not correlate well with those of Pate and Schueler. Comparisons have been made between the skin friction and heat transfer measurements and the theories of Van Driest, Eckert and Spalding and Chi. These comparisons reveal in general that at the high end of our Mach number range (10-13) the theory of Van Driest is in best agreement with the data, whereas at lower Mach numbers (6.5-10) the Spalding Chi theory is in better agreement with the measurements.

Holden, M. S.↗

Turbulent boundary layer in an adverse pressure gradient without effect of wall curvature

The hypersonic compressible turbulent boundary layer in an adverse pressure gradient along a cylindrical axisymmetric body was studied. The tests were conducted in a Mach 6 contoured axisymmetric nozzle. An external compression cowl was used to produce the gradual adverse pressure gradient and a maximum pressure rise of 7 times the freestream static pressure was achieved in a test region of 23 cm. Boundary layer profiles of static pressure, total pressure, and total temperature, as well as wall transient heat transfer rates were measured. Comparisons of the velocity total temperature profiles to linear and quadratic relations were made. Measured heat transfer data were in good agreement with the prediction from the flat-plate reference enthalpy method. Integral parameters were also in good agreement with results of numerical solutions for compressible turbulent boundary layer equations.

Zakkay, V.↗