The nature of the aluminum–aluminum oxide interface: A nanoscale picture of the interfacial structure and energy-level alignment
Explore the source record for details and available documents.
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Explore the source record for details and available documents.
Zinc ion batteries using metallic zinc as the negative electrode have gained considerable interest for electrochemical energy storage, whose development is crucial for the adoption of renewable energy technologies, as zinc has a very high volumetric capacity (5845 mA h cm -3 ), is inexpensive and compatible with aqueous electrolytes. However, the divalent charge of zinc ions, which restricts the choice of host material due to hindered solid-state diffusion, can also pose a problem for interfacial charge transfer. We report our findings on reversible intercalation of up to two Zn 2+ ions in layered V 3 O 7 ·H 2 O. This material exhibits very high capacity and power (375 mA h g -1 at a 1C rate, and 275 mA h g -1 at an 8C rate) in an aqueous electrolyte compared to a very low capacity and slow rate capabilities in a nonaqueous medium. Operando XRD studies, together with impedance analysis, reveal solid solution behavior associated with Zn 2+ -ion diffusion within a water monolayer in the interlayer gap in both systems, but very sluggish interfacial charge transfer in the nonaqueous electrolyte. This points to desolvation at the interface as a major factor in dictating the kinetics. Temperature dependent impedance studies show high activation energies associated with the nonaqueous charge transfer process, identifying the origin of poor electrochemical performance.
Transport behavior of gold nanostructures on Si(100) substrate during annealing under high vacuum has been investigated using in-situ real time transmission electron microscopy (TEM). A comparative study has been done on the morphological changes due to annealing under different vacuum environments. Au thin films of thickness ∼2.0 nm were deposited on native oxide covered silicon substrate by using thermal evaporation system. In-situ real time TEM measurements at 850 °C showed the isotropic growth of rectangular/square shaped gold-silicon alloy structures. During the growth, it is observed that the alloying occurs in liquid phase followed by transformation into the rectangular shapes. For similar system, ex-situ annealing in low vacuum (10{sup −2} millibars) at 850 °C showed the spherical gold nanostructures with no Au-Si alloy formation. Under low vacuum annealing conditions, the rate of formation of the oxide layer dominates the oxide desorption rate, resulting in the creation of a barrier layer between Au and Si, which restricts the inter diffusion of Au in to Si. This work demonstrates the important role of interfacial oxide layer on the growth of nanoscale Au-Si alloy structures during the initial growth. The time dependent TEM images are presented to offer a direct insight into the fundamental dynamics of the sintering process at the nanoscale.
The details of turnover process of spontaneous polarization and associated carrier motions in indium-tin oxide/poly-(vinylidene-trifluoroethylene)/pentacene/Au capacitor were analyzed by coupling displacement current measurement (DCM) and electric-field-induced optical second-harmonic generation (EFISHG) measurement. A model was set up from DCM results to depict the relationship between electric field in semiconductor layer and applied external voltage, proving that photo illumination effect on the spontaneous polarization process lied in variation of semiconductor conductivity. The EFISHG measurement directly and selectively probed the electric field distribution in semiconductor layer, modifying the model and revealing detailed carrier behaviors involving photo illumination effect, dipole reversal, and interfacial charging in the device. A further decrease of DCM current in the low voltage region under illumination was found as the result of illumination effect, and the result was argued based on the changing of the total capacitance of the double-layer capacitors.
Atomic layer deposition (ALD) of ZrO{sub 2} on native oxide covered (untreated) and buffered oxide etchant (BOE) treated AlGaN surface was analyzed by utilizing x-ray photoelectron spectroscopy (XPS) and high-resolution transmission electron microscopy. Evidenced by Ga–O and Al–O chemical bonds by XPS, parasitic oxidation during deposition is largely enhanced on BOE treated AlGaN surface. Due to the high reactivity of Al atoms, more prominent oxidation of Al atoms is observed, which leads to thicker interfacial layer formed on BOE treated surface. The results suggest that native oxide on AlGaN surface may serve as a protecting layer to inhibit the surface from further parasitic oxidation during ALD. The findings provide important process guidelines for the use of ALD ZrO{sub 2} and its pre-ALD surface treatments for high-k AlGaN/GaN metal–insulator–semiconductor high electron mobility transistors and other related device applications.
In this work we have examined the thermodynamics of actinide interactions with solid interfaces in the presence and absence of multi-functional complexing ligands. The term “interactions” is a global term to capture many potential reactions including aqueous complexation, sorption/surface complexation, surface-mediated redox reactions, electrostatic attraction and repulsion, surface passivation, surface precipitation, and counter-ion competition. Each of these potential reactions may control actinide interactions with a solid surface. This work is helping to develop a more fundamental understanding of actinide bonding at solid:water interfaces and examine unique surface mediated oxidation/reduction reactions which are not expected based on the reduction potentials of aqueous species. We place a large emphasis on understanding both sorption and desorption processes as a means of understanding the sorption mechanisms. This work is directly aligned with the DOE BES Heavy Element Chemistry programs interests in understanding “the chemical and physical properties of these elements to determine solution, interfacial and solid-state bonding and reactivity”.
Advancements in materials technologies are needed to provide the aerospace industry with alternate material options in the event of future strategic metal shortages and to optimize performance of engines. Composite materials are promising candidates for such an application. The potential of SiC and B4C-B filament reinforced low strategic element iron-base alloy content composites or use at 760 to 870 C is considered. A limiting factor towards developing this material for high temperature use has been the reaction between the filament and matrix material during fabrication and service which degrades filament strength. A low temperature fabrication process to limit filament/matrix reaction is being developed which involves the use of hollow cathode sputtering to coat the filaments with iron-base alloys of various compositions. An investigation is being conducted to determine the interfacial reaction effects of SiC and B4C-B filaments with iron-base alloys to develop an understanding of filament/matrix alloy compatibility for 760 to 870 C service.
In setting forth its strategic plan, NASA has indicated that low-cost access to space is the key to unleashing the commercial potential of space and greatly expanding space research and exploration. The development of advanced materials will be an enabling technology for this quest for low-cost space access. In this research program, we are attempting to address the need for new advanced materials by developing high-performance nanodispersed inorganic/organic and organic/organic polyimide composites utilizing specific interactions. Our goal is to systematically manipulate these interactions and investigate the resulting processing morphology-property relationships. Specifically, we will investigate three main parameters on these relationships. These include (1) the type of polyimide; (2) the structure of the inorganic nanoparticle being used; and (3) manipulation of the interfacial energy. During the first year of this effort, we have demonstrated the successful synthesis of PMR-15/layered silicate nanocomposites. Morphological studies indicate that exfoliated structures were obtained in most instances, with a mixture of exfoliated and intercalated structures being observed also. Significant enhancements of the onset of decomposition were obtained by varying the strength of the interaction between the nanoparticle and the polymer. Varying the amount of a specific nanoparticle also affected the decomposition temperatures. A slight catalytic effect of the nanoparticles on both the imidization and crosslinking reaction has been observed and will be presented. In addition, incorporation of the nanoparticles was found to increase the glass transition temperature and slightly broaden the breadth of this relaxation.
The contribution from relatively low-K SiON interfacial transition regions (ITRs) between Si and transition metal (TM) gate dielectrics places a significant limitation on equivalent oxide thickness (EOT) scaling for Si complementary metal-oxide-semiconductor (CMOS) devices. This limitation is equally significant and limiting for Ge CMOS devices. Low-K Ge-based ITRs in Ge devices have also been shown to limit performance and reliability, particular for n-MOS field effect transistors. This article identifies the source of significant electron trapping at interfaces between n-Ge or inverted p-Ge, and Ge oxide, nitride and oxynitride ITRs. This is shown to be an interfacial band alignment issue in which native Ge ITRs have conduction band offset energies smaller than those of TM dielectrics, and trap electrons for negative Ge substrate bias. This article also describes a novel remote plasma processing approach for effectively eliminating any significant native Ge ITRs and using a plasma-processing/annealing process sequence for bonding TM gate dielectrics directly to the Ge substrate surface.
The objective of the project was to use synchrotron X-rays to measure the molecular-scale organization of extractants, complexants, buffers, and metal ions at the organic-aqueous (liquid-liquid) interface during solvent back-extraction under conditions relevant to ALSEP (Actinide-Lanthanide Separation Process). The capability of X-ray fluorescence near total reflection (XFNTR) was extended to explore the distribution of Eu(III) between the liquid-liquid interface and bulk organic and aqueous phases which contained extractants HDEHP (bis(2-ethylhexyl) phosphoric acid) and HEHEHP (2-ethylhexyl phosphonic acid mono-2-ethylhexyl ester), the complexant DTPA (diethylene triamine pentaacetic acid), and citric and nitric acids. Although an Am-compatible sample cell was developed, extending x-ray measurements of flat liquid-liquid interfaces to the actinide Am(III) did not prove to be possible within constraints imposed by the Advanced Photon Source. However, preliminary measurements with a drop cell may eventually provide a path forward to investigate Am(III) at a liquid interface. It was also demonstrated that competitive binding that occurs during back-extraction of lanthanide ions to either a phosphoric acid extractant (DHDP, di-hexadecyl phosphate) at the liquid interface or to complexant DTPA in the bulk aqueous phase could be reversibly tuned by X-ray exposure. Separately, X-ray measurements from the liquid-vapor interface explored the role of the aqueous solubility of HDEHP and HEHEHP and their interactions with a range of lanthanides and transition metal ions. Finally, the capability of X-ray absorption spectroscopy (EXAFS) was extended to probe metal ion coordination in lanthanide ion-extractant complexes at the liquid-vapor interface. Complementary to the specific interfacial systems studied during this project, the development of x-ray techniques expands our ability to understand ion ordering at liquid interfaces.
Colloidal halide perovskite nanocrystals or quantum dots (QDs) show similar defect tolerance as thin film perovskite materials with added nanoscale phenomena. Perovskite QD solar cells have demonstrated efficiencies of 16.6%, greater than that of any other QD material system. While the efficiency lags behind the best thin-film perovskite devices, these solar cells could have advantages over the thin-film versions in terms of processability, phase stability, and high open-circuit voltages. However, some operating principles behind perovskite quantum dot device stacks and the associated electric field properties are still unknown. Here, we characterize the junction structure within perovskite QD solar cells, by exposing functioning cross-sections and using nanometer-scale Kelvin probe force microscopy to offer insight into the selection and performance of charge selective contacts. We also evaluated various solar cell device architectures with different selective contacts to isolate the role of each junction in device performance. We show that in high-performance n-i-p architectures, both electron- and hole-transport layer (HTL) interfaces possess a strong electric field, but in the case of the inverted p-i-n architecture, we find that high interfacial recombination at the HTL/QD junction is responsible for subpar device performance. Perovskite QD and thin film materials can synergistically be combined to offer more design flexibility in PV devices, and here we demonstrate that the interface between perovskite thin films and QDs are relatively benign and amenable for synergistic device design.
Highlights: • CCTO/CTO composites were synthesized by a solid-state reaction using various milling durations. • These composites have a broad PL emission band located at 450 nm. • CCTO/CTO material was deposited onto an alumina substrate using a screen-printing technique, and hence, could be structured for gas-sensing applications. • Our theoretical findings may further elucidate the electronic structure associated with the interfacial band alignment (type I-straddling gap). - Abstract: Combined experimental and theoretical investigations were conducted on the electronic structure, as well as the optical and gas-sensing properties of mixed-phase CaCu{sub 3}Ti{sub 4}O{sub 12}/CaTiO{sub 3} (CCTO/CTO) composites, which were synthesized by a solid-state reaction using various milling durations. Our results revealed that these CCTO/CTO composites have a broad photoluminescence (PL) emission band located at 450 nm, which is strongly influenced by the milling process duration. Scanning electron microscopy images confirmed that the use of longer milling durations favored the formation of pores and increased the active surface area of the CCTO/CTO thick films. The thick films were prepared using the screen-printing technique, and hence, could be structured for gas-sensing applications. Our theoretical findings may further elucidate the electronic structure associated with the interfacial band alignment (type I-straddling gap) of the CCTO/CTO composite systems.
Second-order nonlinear optical interactions such as sum- and difference-frequency generation are widely used for bioimaging and as selective probes of interfacial environments. However, inefficient nonlinear optical conversion often leads to poor signal-to-noise ratio and long signal acquisition times. We demonstrate the dramatic enhancement of weak second-order nonlinear optical signals via stimulated sum- and difference-frequency generation. We present a conceptual framework to quantitatively describe the interaction and show that the process is highly sensitive to the relative optical phase of the stimulating field. To emphasize the utility of the technique, we demonstrate stimulated enhancement of second harmonic generation (SHG) from bovine collagen-I fibrils. Using a stimulating pulse fluence of only $3\text{ }\text{ }\mathrm{nJ}/{\mathrm{cm}}^{2}$, we obtain an SHG enhancement >${10}^{4}$ relative to the spontaneous signal. The stimulation enhancement is greatest in situations where spontaneous signals are the weakest—such as low laser power, small sample volume, and weak nonlinear susceptibility—emphasizing the potential for this technique to improve signal-to-noise ratios in biological imaging and interfacial spectroscopy.
Here, utilizing recent advancements in computational schemes for compressible, multiphase flows, this work features a parametric study of a pure liquid jet in supersonic crossflow that involves simulating the atomization process for four values of momentum-flux ratio. These simulations are validated against experimental results measured with high-speed X-ray imaging, which confirm the accuracy of the numerical approach. Also, the effect of numerical resolution on some flow behavior is investigated, revealing convergence of the jet shape and surface instability wavelength. Analysis of the resulting sprays includes statistical descriptions of the liquid distribution, liquid structures created through breakup, interfacial instabilities, and dominant flow features. As the flowrate increases, the spray penetrates further, it becomes more disperse, and less liquid impacts the wall, but the droplet size distribution changes little. The wavelength of instabilities on the windward side of the jet diverges from measured trends in subsonic crossflows. In a visualization of the time-averaged flow, counter-rotating vortices are observed along the jet core and in the wake, affecting the process of primary atomization and early droplet trajectories.
Many materials employed in critical structural applications depend upon metastable strengthening precipitates that transform or dissolve at elevated temperatures. Herein, aberration-corrected scanning transmission electron microscopy and first-principles calculations are used to accurately determine the atomic structure of the highly mobile, semi-coherent precipitate interfaces that control this process in the classic θ' (Al 2 Cu) precipitate in the Al-Cu system. Semi-coherent {110} interfaces are found to be composed of an array of unexpected misfit dislocations that are arranged in two different structural units. Dislocations accommodate nearly all of the misfit between the Al matrix and strengthening phase. Cu is observed to segregate to the compressed edge of the dislocation cores at specific sites in this interface. First-principles calculations revealed the energetic landscape that facilitates these sites to become entry and exit gateways of Cu atoms in this semi-coherent interface. In conclusion, this investigation reveals critical features within semi-coherent interfaces that determine the thermal stability of precipitation-hardened alloys.
Weak van der Waals adsorption of π-conjugated hydrocarbon molecules onto the gold surface, Au(111), is one of the essential processes in constructing organic-metal interfaces in organic electronics. Here we provide a first direct observation of adsorption geometry of a single π-conjugated hydrocarbon molecule on Au(111) using an atomically resolved scanning tunneling microscopy study combined with van der Waals density functional methodology. For the purpose, we utilized a highly symmetric π-conjugated hydrocarbon molecule, dehydrobenzo[12]annulene (DBA), which has a definite three-fold symmetry, the same as the Au(111) surface. Interestingly, our observations on an atomically resolved scale clearly indicate that the DBA molecule has only one adsorption configuration on Au(111) in spite of the weak van der Waals adsorption system. Based on the precisely determined adsorption geometry of DBA/Au(111), our calculation results imply that even a very small contribution of the interfacial orbital interaction at the organic-metal interface can play a decisive role in constraining the adsorption geometry even in the van der Waals adsorption system of a π-conjugated hydrocarbon molecule on the noblest Au(111) surface. Our observations provide not only deeper insight into the weak adsorption process, but also new perspectives to organic electronics using π-conjugated hydrocarbon molecules on the Au surface.
The low-interfacial tension flow through porous media occurs in surfactant-based enhanced oil recovery (EOR), soil clean-up, underground removal of the non-aqueous phase liquid and dense non-aqueous phase liquid, etc. In surfactant-based EOR processes, numerous works have been carried out to characterize - either qualitatively or quantitatively - the micro- and macro-scale flow behavior. What has been lacking is to link the statistics of oil blobs population (e.g., distribution of blob length and diameter) to the pore-scale phenomena and macro-scale quantities. In particular, no work has been reported to elucidate the effect of the ratio of pore body to throat diameter (i.e., aspect ratio) on the pore-scale characterization based on the blobs population statistics. The significance of the aspect ratio lies in that it describes the geometry of a porous medium and is one of the foremost morphological features. The aspect ratio is also one of the fundamental factors governing the pore-level events. This study presents the effect of aspect ratio on the statistical distribution of the blob length and equivalent diameter and links the blobs population statistics to the observed pore-level events. The pore-scale variation of the ratio of viscous-to-capillary forces acted on the oil blobs at the threshold of displacement is utilized to characterize the effect of blob length distribution at different aspect ratios. It also provides some insight into correlating the change in oil recovery efficiency and capillary number, by change in aspect ratio, with the change in blobs population statistics. (author)
To match the strength of wire-arc additive manufactured Haynes 282 to its wrought counterpart via a single-step aging heat treatment, the CALPHAD (Calculation of Phase Diagrams) method is integrated with physics-based process-structure-property models and experimental validation. The integrated computational materials engineering (ICME) framework simulates the effects of aging on γ′ and M 23 C 6 precipitation and the resulting yield strength. To improve simulation reliability, the interfacial energies between γ/γ′ and γ/M 23 C 6 carbides were estimated by comparison with precipitation kinetic modeling and measured precipitate sizes. γ′ and M23C6 were found to precipitate simultaneously between 640 and 860 °C, producing microstructures similar to those produced by two-step aging. The optimal γ′ size for peak yield stress was calculated to be 20–23 nm. WAAM Haynes 282 aged at 780 °C for 50 h exceeded the mechanical performance of its wrought counterpart subjected to two-step aging, though desired properties can also be achieved at 800 °C for 16 h or less. The error in yield strength is less than 20 MPa, demonstrating good agreement between the modeling framework and experiments. Creep studies showed that WAAM Haynes 282 exceeded the calculated rupture time, reaching 481 h. This proposed methodology can accelerate the design of aging heat treatments for any γ′-strengthened nickel-base alloy, minimizing the resources required for trial-and-error experiments.