Search NASA⌕ Search

SEARCH · Search NASA

Results for “load changes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,153 records · Page 64

Identification of a Pt 3 Co Surface Intermetallic Alloy in Pt–Co Propane Dehydrogenation Catalysts

Bimetallic Pt-Co nanoparticles (NPs) were prepared and characterized by scanning transmission electron microscopy, in situ X-ray absorption spectroscopy, in situ synchrotron X-ray diffraction, and catalytic conversion for propane dehydrogenation with and without added H-2. In addition, the surface extended X-ray absorption fine structure (EXAFS) obtained by fitting the difference spectrum between the fully reduced and room-temperature-oxidized catalysts suggest that the surface structure remains Pt 3 Co, although the core changes from Pt to Pt 3 Co and to PtCo. At low Co loading, the bimetallic nanoparticles form a Pt3Co intermetallic surface alloy with Pt-rich core. With increasing Co loading, a full alloy forms where both the surface and NP compositions are Pt 3 Co. A further increase in Co loading leads to a Co-rich NP core, likely PtCo, with a surface of Pt 3 Co. Although Pt-Co intermetallic alloys form two different phases and several morphologies, the surface structures are similar in all catalysts. Although both monometallic Pt and Co are active for alkane dehydrogenation, all bimetallic Pt-Co catalysts are significantly more olefin selective than either single metal. The turnover rates of the bimetallic catalysts indicate that Pt is the active atom with little contribution from Co atoms. The high olefin selectivity is suggested to be due to Co acting as a less active structural promoter to break up large Pt ensembles in bimetallic NPs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Comprehensive Study of the Impact of Steam on Polyethyleneimine on Silica for CO 2 Capture

An amine sorbent, prepared by impregnation of polyethyleneimine on silica, was tested for steam stability. The stability of the sorbent was investigated in a fixed bed reactor using multiple steam cycles of 90 vol % H 2 O/He at 105 °C, and the gas effluent was monitored with a mass spectrometer. CO 2 uptake of sorbent was found to decrease with repeated exposure to steam. Characterization of the spent sorbent using N 2 physisorption, SEM, and thermogravimetric analysis (TGA) showed that the decrease in CO 2 loading can possibly be attributed to a reagglomeration of the amine in the pores of the silica. No support effect was found in this study. The commercial SiO 2 used, Cariact G10, was found to be stable under the conditions used. While it was found that subjecting the sorbent to several steam cycles decreased its CO 2 uptake, a continuous exposure of the sorbent to steam did not have a significant performance impact. Finally, a silanated sorbent, consisting of a mixture of PEI and aminopropyl-triethoxysilane on SiO 2 support, was also investigated for steam stability. Similarly to the nonsilanated sorbent, the CO 2 loading of this sorbent decreased upon steam exposure, although a mechanism for this change has not been postulated at this time.

54 ENVIRONMENTAL SCIENCES↗

ICRF heating at JET: From operations with a metallic wall to the long term perspective of a DT campaign

The first series of experiments with the ITER-like wall (ILW) will start mid-2011 with D plasmas and will continue through 2012-13 with H, {sup 4}He and D plasmas, and up to 2014-15, when a DT campaign is proposed. In this paper, the previous experience at JET is reviewed to set the scene for the future challenges of ICRF operation including change in the ICRF coupling, W impurity production and evaluation of localized power loads due the RF sheaths. development in a Beryllium/Tungsten environment of ICRF heating schemes for the non activated and the DT phases of ITER.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spallation as a dominant source of pusher-fuel and hot-spot mix in inertial confinement fusion capsules

We suggest that a potentially dominant but previously neglected source of pusher-fuel and hot-spot “mix” may have been the main degradation mechanism for fusion energy yields of modern inertial confinement fusion (ICF) capsules designed and fielded to achieve high yields — not hydrodynamic instabilities. This potentially dominant mix source is the spallation of small chunks or “grains” of pusher material into the fuel regions whenever (1) the solid material adjacent to the fuel changes its phase by nucleation, and (2) this solid material spalls under shock loading and sudden decompression. Finally, we describe this mix mechanism, support it with simulations and experimental evidence, and explain how to eliminate it and thereby allow higher yields for ICF capsules and possibly ignition at the National Ignition Facility.

42 ENGINEERING↗

The Electron Thermal Conductivity of Pu and Zr Substituted $\mathcal{γ}$-U

Uranium alloys are attractive recycled nuclear fuels because of their high thermal conductivity (𝑘) and fissile density. Limited experimental studies of the 𝑘 of U-Pu-Zr alloys in the range of 15 to 20 wt% Pu and 6 to 15 wt% Zr indicate that increasing the content of either Zr or Pu tends to lower 𝑘. However, which element has the greater effect on 𝑘, and the associated mechanisms, remains unclear. Here, in this study, the electron thermal conductivity (𝑘 𝑒 ) of U-Pu-Zr compositions are calculated using density functional theory. The electronic structure is evaluated to understand the effects of plutonium (Pu) and zirconium (Zr) substitution on the 𝑘 𝑒 of 𝛾-U. Alloys of up to 37.5 at. % Pu and 37.5 at. % Zr are examined. Two methods are applied to calculate 𝑘 𝑒 ; we find that the accuracy of each method depends on the electronic and mass similarities between the solute and solvent atoms. Specifically, when the solute atom is similar in electronic structure and mass, the more accurate method is that which employs the electron relaxation time of 𝛾-U, while if the elements are dissimilar, a mixed method that mixes several parameters associated with JNW_S⁢3033426825100132 from each element in the alloy is best. The introduction of all alloying elements decreases 𝑘 𝑒 ; however, in binary compounds, Pu and Zr have different effects. Pu flattens the electronic bands but compensates for this deleterious effect by increasing electron density near the Fermi level. Zr flattens the electronic bands more severely without adding electron density near the Fermi level. Therefore, Zr decreases 𝑘 𝑒 more than Pu in binary compounds. In ternary compounds, the difference between Pu and Zr is minimal due to the phononic change from the large mass change of Zr substitution, even at 12.5 at. %. Thus, we predict that higher loadings of Pu, and potentially other actinides, can be added to U-Pu-Zr compositions for faster recycling of spent fuel without sacrificing 𝑘. We also note that these 𝑘 𝑒 calculation methods can be applied to non-fuel alloys that require 𝑘 𝑒 predictions, such as cladding, heat exchanger, and structural materials.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Nanoindentation of ion-implanted crystalline germanium

Most indentation studies to date on crystalline germanium (c-Ge) and related covalent semiconductors have been carried out on pristine defect-free material. This paper addresses the paucity of studies on imperfect crystalline materials by exploring the impact of defects generated by ion implantation, prior to contact damage, upon the mechanical properties of c-Ge. Implantation with Ge ions is carried out to generate a layer of highly defective but still-crystalline Ge. Under nanoindentation with a sharp diamond tip, enhanced plasticity is observed relative to pristine material. Characterization by cross-sectional transmission electron microscopy, atomic force microscopy, and load curve analysis shows softening, quasiductile extrusion, and cracking suppression taking place. These changes can be explained by the high density of defects, and dangling bonds in particular, created by ion implantation and revealed by positron-annihilation spectroscopy, and are proportional to the fraction of 'missing bonds' or vacancies in the material. A thermal annealing step at 200 deg. C is sufficient to restore the mechanical response of pristine material, despite incomplete recovery of the original pristine crystal structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Defect control in the Heisenberg-Kitaev candidate material NaRuO 2

The combination of geometric frustration, extended hopping, spin-orbit coupling, and a disordered magnetic ground state make NaRuO 2 an attractive Heisenberg-Kitaev candidate material. Historically, NaRuO 2 has been a challenging material to produce, even in polycrystalline form. Here we present synthetic efforts that identify a propensity for Na Ru defects to form in NaRuO 2 , revealing a full solid-solution between NaRuO 2 and disordered Na 2 RuO 3 . We report the synthesis of alloys along the Na 3+x Ru 3–x O 6 solid solution and characterize changes in the bulk magnetization and electron transport as a function of Na loading. Furthermore, our results highlight the importance of stoichiometry control in NaRuO 2 when investigating and interpreting this material’s physical properties.

36 MATERIALS SCIENCE↗

Hardware-in-the-Loop Co-simulation of Distribution Grid for Demand Response

In modern power systems, co-simulation is proposed as an enabler for analyzing the interactions between disparate systems. This paper introduces the co-simulation platform Virtual Grid Integration Laboratory (VirGIL) including Hardware-in-the-Loop testing, and demonstrates its potential to assess demand response strategies. VirGIL is based on a modular architecture using the Functional Mock-up Interface industrial standard to integrate new simulators. VirGIL combines state-of-the-art simulators in power systems, communications, buildings, and control. In this work, VirGIL is extended with a Hardware-in-the-Loop component to control the ventilation system of a real 12-story building in Denmark. VirGIL capabilities are illustrated in three scenarios: load following, primary reserves and load following aggregation. Experimental results show that the system can track one minute changing signals and it can provide primary reserves for up-regulation. Furthermore, the potential of aggregating several ventilation systems is evaluated considering the impact at distribution grid level and the communications protocol effect.

Rotger-Griful, Sergi↗

Pulse: An Outlier Sensitive Downsampling Algorithm For Timeseries Data

Pulse is a downsampling algorithm for timeseries data. Frequently datasets become so large that visualization tools and web browsers cannot effectively render graphics due to memory constraints. Downsampling algorithms are commonly applied to minimize the quantity of data required to visualize important features or trends in the data, but some datasets are composed by distinct enough features and trends that most existing downsampling algorithms fail to preserve them. Pule was developed to downsample timeseries data for galvanostatic stack test data at the Idaho National Laboratory. These datasets were composed by approximately 4 million records, most of them being extremely uniform. However, during relatively brief time periods when the stack test changes state, for example when the test article is powered on, or a load is added, the data produce sparse asymptotes. No existing downsampling algorithm was capable of preserving the sparse asymptotes in electrolysis stack test data. Instead, we develop a downsampling algorithm that preserves important outliers in data, and otherwise aggressively downsamples uniform data. The algorithm has applications in other domains like seismology, in the measurement of earthquakes, or astronomy, in the measurement of quasars or transit photometry.

Woodruff, Nathan [Idaho National Laboratory (INL),↗

EmissionsFlexibility

Software to calculate the how changes in electricity consumption change the generator which provides the electricity. This is applied to find how load shifting (e.g. data centers) impact the carbon emissions of the power grid.

Rhodes, Noah↗

Technical Support Document for a Proposed IECC Glazing Orientation Restriction

This report describes a proposed revision to the International Energy Conservation Code that would restrict the amount of west-facing glazing permitted on low-rise residential buildings. The purpose and structure of the proposed change are discussed and its potential impacts on energy consumption and cooling peak load are quantified based on hour-by-hour building energy simulation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Iodine adsorption on ion-exchange resins and activated carbons: batch testing

Iodine sorption onto seven resins and six carbon materials was evaluated using water from well 299-W19-36 on the Hanford Site. These materials were tested using a range of solution-to-solid ratios. The test results are as follows. The efficacy of the resin and granular activated carbon materials was less than predicted based on manufacturers’ performance data. It is hypothesized that this is due to the differences in speciation previously determined for Hanford groundwater. The sorption of iodine is affected by the iodine species in the source water. Iodine loading on resins using source water ranged from 1.47 to 1.70 µg/g with the corresponding K d values from 189.9 to 227.0 mL/g. The sorption values when the iodine is converted to iodide ranged from 2.75 to 5.90 µg/g with the corresponding K d values from 536.3 to 2979.6 mL/g. It is recommended that methods to convert iodine to iodide be investigated in fiscal year (FY) 2015. The chemicals used to convert iodine to iodate adversely affected the sorption of iodine onto the carbon materials. Using as-received source water, loading and K d values ranged from 1.47 to 1.70 µg/g and 189.8 to 226.3 mL/g respectively. After treatment, loading and K d values could not be calculated because there was little change between the initial and final iodine concentration. It is recommended the cause of the decrease in iodine sorption be investigated in FY15. In direct support of CH2M HILL Plateau Remediation Company, Pacific Northwest National Laboratory has evaluated samples from within the 200W pump and treat bioreactors. As part of this analysis, pictures taken within the bioreactor reveal a precipitate that, based on physical properties and known aqueous chemistry, is hypothesized to be iron pyrite or chalcopyrite, which could affect iodine adsorption. It is recommended these materials be tested at different solution-to-solid ratios in FY15 to determine their effect on iodine sorption.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Modeling the mechanical and aging properties of silicone rubber and foam - stockpile-historical & additively manufactured materials

M97* and M9763 belong to the M97xx series of cellular silicone materials that have been deployed as stress cushions in some of the LLNL systems. Their purpose of these support foams is to distribute the stress between adjacent components, maintain relative positioning of various components, and mitigate the effects of component size variation due to manufacturing and temperature changes. In service these materials are subjected to a continuous compressive strain over long periods of time. In order to ensure their effectiveness, it is important to understand how their mechanical properties change over time. The properties we are primarily concerned about are: compression set, load retention, and stress-strain response (modulus).

36 MATERIALS SCIENCE↗

Advancement Of Tritium Powered Betavoltaic Battery Systems FY16 EOY Report

The goal of this work is to increase the power output of tritium-powered betavoltaic batteries and investigate the change in power output and film resistance in real-time during tritium loading of adsorbent films. To this end, several tritium-compatible test vessels with the capability of measuring both the resistivity of a tritium trapping film and the power output of a betavoltaic device in-situ have been designed and fabricated using four electrically insulated feedthroughs in tritium-compatible load cells. Energy conversion devices were received from Widetronix, a betavoltaic manufacturing firm based in Ithaca, NY. Thin films were deposited on the devices and capped with palladium to facilitate hydrogen loading. Gold contacts were then deposited on top of the films to allow resistivity measurements of the film during hydrogen loading. Finally, the chips were wire bonded and installed in the test cells. The cells were then baked-out under vacuum and leak checked at temperature to reduce the chances of tritium leaks during loading. Following the bake-out, IV curves were measured to verify no internal wires were compromised, and the cells were delivered to Tritium for loading. Tritium loading is anticipated in October, 2017.

07 ISOTOPE AND RADIATION SOURCES↗

Impacts of High Variable Renewable Energy Futures on Wholesale Electricity Prices, and on Electric-Sector Decision Making

Increasing penetrations of variable renewable energy (VRE) can affect wholesale electricity price patterns and make them meaningfully different from past, traditional price patterns. Many long-lasting decisions for supply- and demand-side electricity infrastructure and programs are based on historical observations or assume a business-as-usual future with low shares of VRE. Our motivating question is whether certain electric-sector decisions that are made based on assumptions reflecting low VRE levels will still achieve their intended objective in a high VRE future. We qualitatively describe how various decisions may change with higher shares of VRE and outline an analytical framework for quantitatively evaluating the impacts of VRE on long-lasting decisions. We then present results from detailed electricity market simulations with capacity expansion and unit commitment models for multiple regions of the U.S. for low and high VRE futures. We find a general decrease in average annual hourly wholesale energy prices with more VRE penetration, increased price volatility and frequency of very low-priced hours, and changing diurnal price patterns. Ancillary service prices rise substantially and peak net-load hours with high capacity value are shifted increasingly into the evening, particularly for high solar futures. While in this report we only highlight qualitatively the possible impact of these altered price patterns on other demand- and supply-side electric sector decisions, the core set of electricity market prices derived here provides a foundation for later planned quantitative evaluations of these decisions in low and high VRE futures.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Multi-scale experimental study of creep-fatigue failure initiation in a 709 Stainless Steel alloy using high resolution digital image correlation. Final report

This report discusses the efforts made towards the multi-scale study of the creep-fatigue response of stainless steel 709. Multiple experimental techniques, including digital image correlation (DIC) and electron backscatter diffraction (EBSD), were used in assessing the evolution of damage accumulation during fatigue, creep-fatigue, and thermomechanical fatigue of alloy 709. The role of microstructural features, hold times, temperature, and loading profiles were quantified and the interchangeability of temperature and time was investigated. Finally, a thermomechanical fatigue model was shown to predict well the failure of samples with varying loading profiles. Results indicate that strain accumulation in 709 steel happens primarily near grain boundaries (GBs) with the strains around GBs being inversely proportional to their measured residual burgers vector. Furthermore, hot-spots for strain accumulation were shown to be the locations of eventual microcrack nucleation. The introduction of hold times to the periodic loading cycle increases the damage accumulation rate and thus shortens the fatigue life of samples–this was true for both room temperature and high temperature. Thermomechanical cycling was shown to have little effect on the end life of samples, with the damage accumulation rate for in-phase and out-of-phase cycling being similar to isothermal fatigue. The interchangeability of time and temperature was shown to be possible within the studied load, time, and temperature ranges, since deformation mechanisms driving strain accumulation did not change with temperature (up to 650°C). The Neu-Sehitoglu thermomechanical fatigue model, with constants obtained from the literature and in part from our experimental results, was applied to predict failure of isothermal creep-fatigue samples. The main objectives of this work were to:(a) Perform high-resolution digital image correlation measurements (HiDIC) for alloy 709; (b) Quantify and assess damage accumulation at the microstructure under fatigue, TMF, and creep-fatigue conditions of 709; (c) Study of the role of hold times, i.e., adding a creep component, to: Room temperature cycling, High temperature cycling, Failure; (d) Study the mechanisms of thermomechanical fatigue in this alloy; (e) Investigate the existence of a time-temperature interchangeability criterion to aid in accelerated creep-fatigue testing; (f) Establish the validity of a combined creep-fatigue model for life prediction for 709. This report is structured with each subsequent section detailing the efforts, results, and conclusions related to each of the objectives described, mostly in chronological order.

36 MATERIALS SCIENCE↗

Effects of Aerosols on Autumn Precipitation over Mid-Eastern China

Long-term observational data indicated a decreasing trend for the amount of autumn precipitation (i.e. 54.3 mm per decade) over Mid-Eastern China, especially after 1980s (~ 5.6% per decade). To examine the cause of the decreasing trend, the mechanisms associated with the change of autumn precipitation were investigated from the perspective of water vapor transportation, atmospheric stability and cloud microphysics. Results show that the decrease of convective available potential energy (i.e. 12.81 J kg-1/ decade) and change of cloud microphysics, which were closely related to the increase of aerosol loading during the past twenty years, were the two primary factors responsible for the decrease of autumn precipitation. Ours results showed that increased aerosol could enhance the atmospheric stability thus weaken the convection. Meanwhile, more aerosols also led to a significant decline of raindrop concentration and to a delay of raindrop formation because of smaller size of cloud droplets. Thus, increased aerosols produced by air pollution could be one of the major reasons for the decrease of autumn precipitation. Furthermore, we found that the aerosol effects on precipitation in autumn was more significant than in other seasons, partly due to the relatively more stable synoptic system in autumn. The impact of large-scale circulation dominated in autumn and the dynamic influence on precipitation was more important than the thermodynamic activity.

AEROSOLS↗

Submerged Pressure Differential Plate Wave Energy Converter with Variable Geometry: Preprint

This work presents a novel wave energy converter device concept that combines a submerged pressure differential plate with variable geometry modules. The two variable geometry sections, placed at the force and aft locations on the plate, consist of five identical flaps that are opened in ascending order starting with the flaps closest to the edges of the plate and moving inward. The variable geometry modules act as control surfaces that allow for the hull geometry to be adjusted leading to changes in the hydrodynamics. The device geometry is controlled in a quasi-static fashion while the power-take off (PTO) unit would be controlled on a wave-to-wave time scale. The submerged plate is tethered directly to the seabed by integrated mooring and PTO lines eliminating the need for a second reaction body. A linear frequency domain analysis is used to evaluate device performance in terms of absorbed power, PTO force, and absorber body motion. The frequency domain analysis required the linearization of the PTO dynamics to couple the fore and aft PTOs to the motion of the absorber body. The inclusion of the variable geometry modules was shown to be effective at altering the device geometry to provide changes in the absorber hydrodynamics to produce measurable reductions in structural and PTO loading.

16 TIDAL AND WAVE POWER↗