Search NASA⌕ Search

SEARCH · Search NASA

Results for “ASHES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Phase assemblage of composite cements

The phase assemblage of binary Portland cements with 45 wt% replacement by calcareous fly ash and slag has been investigated by experiment, mass balance and thermodynamic simulations. The input for these calculations was based on clinker reaction measured by XRD-Rietveld refinement, on SCM reaction measured by SEM-EDS full element mapping and on C-S-H composition by SEM-EDS point analyses. A sensitivity analysis estimates the uncertainty of determination of phase volume as at best ± 2 cm{sup 3}/100 cm{sup 3}, and thus of rather semi-quantitative character. The differences between experiment and calculations regarding AFt/AFm, C-S-H and portlandite were assessed. Gel/space ratios computed using the volumes of all hydrates showed a clear correlation to compressive strength, which was unaffected by the mix composition. This suggests that the type of hydrates formed has little or no influence on the compressive strength and that the key factor is the space filling.

36 MATERIALS SCIENCE↗

Resistance of concrete to different exposures with chloride-based salts

Formation of complex salts (oxychlorides) has been suspected for causing chemical degradation of concrete in cold regions. In this study, conditioned mode (controlled temperature and relative humidity) environmental scanning electron microscopy was specifically used to minimize changes in the crystal structures of oxychlorides phases and thus reliably capture their unaltered morphology and existence/effects on concrete exposed to different de-icing salts under two different environmental conditions (constant low temperature and wetting/drying (W/D) cycles). Formation of acicular flattened blades of 3- and 5-form magnesium oxychloride (MOX) and tiny fibrous crystals as well as subhedral pseudo-hexagonal calcium oxychloride plates (COX) were found in deteriorated concrete specimens, depending on the type of solution. The reversible formation of hydrous and anhydrous COX during W/D cycles had a significant effect on aggravating the kinetics of damage of concrete in this exposure. The combined salt (MgCl{sub 2} + CaCl{sub 2}), which simulates using a synergistic maintenance and protective strategy for concrete pavements in winter, was the most aggressive solution; thus, this practice should be cautiously reconsidered. The incorporation of 30% fly ash had a pronounced effect on improving the concrete resistance to damage as reflected by sound mechanical properties and longevity. Also, the performance of concrete was much enhanced when an innovative supplementary cementitious material, nanosilica, was incorporated in the cementitious system.

36 MATERIALS SCIENCE↗

Microstructural packing- and rheology-based binder selection and characterization for Ultra-high Performance Concrete (UHPC)

This paper reports strategies to design the binder phase of ultra-high performance concretes (UHPC) from commonly available cement replacement (fly ash, slag, microsilica, metakaolin) and fine filler (limestone) materials. A packing algorithm is used to extract the number density, mean centroidal distance, and coordination number of the microstructure. Similarly, rheological studies on the pastes provide yield stress, plastic viscosity, and min-slump spread. The selection criteria involves using the three microstructural and three rheological parameters individually or in combination to define packing and flow coefficients. The selection criteria is flexible enough to allow users modify the constraints depending on the application. In this study, only ternary and quaternary blends, with a total cement replacement of 30% by mass are selected for further characterization. The highly efficient microstructural packing in these mixtures and better workability that facilitated dispersion of particles to enhance the reactivity results in beneficial pore structure and mechanical properties.

36 MATERIALS SCIENCE↗

Estimating the mechanical properties of hydrating blended cementitious materials: An investigation based on micromechanics

The hydration model of Parrot & Killoh (1984) has been extended to blended cements and coupled to a micromechanical scheme similar to that of Pichler & Hellmich (2011) to estimate the Young modulus and the compressive strength of cementitious materials as a function of time. A finite aspect ratio of 7 is introduced to describe the shape of the hydrates and improve the estimate of the early age strength by the micromechanical scheme. Furthermore, accounting for the stress fluctuations in the cement paste partly explains the fact that the compressive strength of a concrete can be lower than that of its cement paste. Finally, the estimated physical properties are compared to numerous experimental measurements from the literature and new experimental measurements on blended cement pastes featuring significant weight fractions of limestone filler, fly ash or silica fume. It is shown that the present model slightly overestimates the dilution effect.

36 MATERIALS SCIENCE↗

Mechanical properties and durability performance of concretes with Limestone Calcined Clay Cement (LC3)

The adoption of any binder system for structural concrete depends on the performance characteristics desired for addressing the long-term deformation and durability concerns. The major properties influencing the performance includes the shrinkage characteristics governing the long-term deformation, and durability characteristics related to various transport mechanisms, governing the performance in different service conditions. This paper describes the potential of Limestone Calcined Clay Cement (LC{sup 3}) for use in structural concrete in comparison with Ordinary Portland Cement (OPC) and fly ash based blended cement (FA30). Three types of concrete mixtures were designed for the study, two based on achieving an equivalent strength grade (M30 and M50 concrete grade) with each binder, and the third with equal binder content and w/b ratio. Mechanical properties such as compressive strength and elastic modulus, and autogenous and drying shrinkage, along with various durability parameters of the different concretes were assessed. Oxygen permeability, rapid chloride penetration, chloride migration, resistivity development and water sorptivity were the various parameters considered for evaluation of durability performance. The results indicate the superiority of LC{sup 3} binder over other binders in producing durable concrete, especially in a chloride laden environment. The major reason for the better performance was attributed to the more compact and dense microstructure of the system with the LC{sup 3} binder against OPC and FA30. The drying shrinkage performance was seen to be similar for concrete with all three binders.

36 MATERIALS SCIENCE↗

Unveiling micro-chemo-mechanical properties of C–(A)–S–H and other phases in blended-cement pastes

Current demand for novel highly sustainable concrete urges improving the links between chemical and mechanical effects of supplementary cementitious materials (SCMs) on the microstructure of blended-cement pastes. In this work, coupled NanoIndentation and Quantitative Energy Dispersion Spectroscopy (NI-QEDS) was applied to disclose chemo-mechanical properties of microstructure phases in systems incorporating typical dosages of fly ash, slag, metakaolin, or glass powder. For a fixed water-to-binder ratio of 0.4, the C–(A)–S–H chemistry was significantly affected by the SCMs, while its average mechanical properties varied within the limited ranges M ≈ 25–27 GPa, H ≈ 0.7–0.8 GPa and C ≈ 180–230 GPa. The SCMs further changed the arrangement of anhydrous phases and minor hydrates embedded in the C–(A)–S–H matrix, which were also characterized (e.g., Portlandite, AFm such as carboaluminates, or an hydrotalcite-like phase). Finally, engineering properties of blended-cement matrices requires tailoring both the intermix of hydrates and the rigid anhydrous SCM inclusions.

36 MATERIALS SCIENCE↗

Influence of fiber inclination angle on bond-slip behavior of different alkali-activated composites under dynamic and quasi-static loadings

This study investigates the influence of inclination angle (0° and 45°) on the interfacial bond-slip behavior of macro steel fibers (straight, hooked end-deformed and length-deformed) and length-deformed polypropylene fibers reinforced in fly-ash and metakaolin based alkali-activated composites (AACs) under quasi-static and dynamic loadings. AACs demonstrate superior peak bond strength and toughness compared to cement composites regardless of fiber type and loading rate. Results also show that straight steel fiber exhibits a complete pullout in AACs. The amount of deformation of the fibers (deformation ratio) determined the failure type at different inclination angle and loading rate, thus governing the peak load and energy absorption. Depending on the fiber orientation, premature fiber rupture or matrix cracking is observed under dynamic loading in AACs due to matrix brittleness. The fiber failure modes in dynamic pullout are no different from those observed in the quasi-static pullout in AACs.

36 MATERIALS SCIENCE↗

Changes in microstructure characteristics of cement paste on carbonation

This study investigates the influence of carbonation on the microstructure of cement paste cast with Ordinary Portland Cement (OPC), fly ash based Portland Pozzolana Cement (PPC) and Limestone Calcined Clay Cement (LC{sup 3}) using X-ray diffraction (XRD), thermal analysis (TGA), scanning electron microscope (SEM) and mercury intrusion porosimeter (MIP). A comparison is made between samples exposed to 3% carbon dioxide concentration and those exposed to natural CO{sub 2} concentrations. It is observed that the products formed on carbonation are similar in both the exposure conditions. Distinct rims corresponding to decalcified C-S-H are observed around clinker grains in the carbonated samples. Coarsening of pore structure is observed on carbonation in all the cements and an increase in the total porosity is observed in blended cements. Thermodynamic modeling indicates irrespective of the type of cement the total solid volume is reduced on complete carbonation. The volume change occurring on carbonation obtained from experimental results and thermodynamic modeling are compared.

36 MATERIALS SCIENCE↗

Modelisation of chloride reactive transport in concrete including thermodynamic equilibrium, kinetic control and surface complexation

In this study, a new physically and chemically based model taking into account thermodynamic equilibrium, kinetics and surface complexation is proposed to predict the ingress of chloride ions into saturated concretes. The numerical results of this multi-ionic model are compared to experimental data such as total and free chloride concentration profiles and chloride binding isotherms. With only one set of parameters, the results show very good agreement for chloride binding isotherm of concretes with different w/b, types of binders (CEM I, CEM III, and CEM I with fly ash) and various exposure conditions (NaCl solution at different concentrations). Such a model overcomes the use of empirical chloride binding isotherms that can be difficult to asses for concretes with supplementary cementitious materials. The very good results underline the need to take into account all the physical and chemical phenomena included in the model.

36 MATERIALS SCIENCE↗

Hydration behavior of cements with reduced clinker factor in mixture with sulfoaluminate binder

CO{sub 2} regulation and raw material availability will strongly influence the future cement market and a wider use of composite cements containing limestone and pozzolan or slag is expected. In the present paper, the possibility to combine Portland cements (PCs) with reduced clinker factor with sulfoaluminate cement (CSA), is explored. Low Portland clinker cements are prepared in laboratory using different supplementary cementitious materials (limestone, slag, pozzolan and fly ash) and mixed with a sulfoaluminate cement: the hydration behavior of the resulting binders is investigated up to 90 days through a multi-technique approach involving X-ray diffraction, differential scanning calorimetry and nuclear magnetic resonance spectroscopy. Understanding the interaction mechanisms between SCMs and CSA/PC blends will support the development of innovative high performing binders based on CEM III or CEM V, or even on new standardized CEM II. Results highlight that slag is particularly suitable promoting late strength development.

36 MATERIALS SCIENCE↗

Long-term cement hydration studies with isothermal calorimetry

The purpose of this study was to investigate for how long the thermal power of hydration can be measured with isothermal calorimetry, which is a general measurement technique with stable properties that, in many cases, can detect low rates of processes. Measurements were conducted for 365 days on cement paste with Portland cement, fly ash blended Portland cement and different water-to-binder ratios. The results showed that all the tested systems still produced a measureable signal after one year. The samples with Portland cement were also analyzed by XRD after 365 days, and phase composition calculations were made with GEMS. Together with the calorimetric results, these results were used to determine the degree of hydration by five methods, the results of which showed good agreement.

36 MATERIALS SCIENCE↗

Efficacy of SCMs to mitigate ASR in systems with higher alkali contents assessed by pore solution method

This study demonstrates the efficacy of supplementary cementitious materials (SCMs) to mitigate alkali-silica reaction (ASR) even when used in conjunction with cement of higher alkali contents (up to 1% Na{sub 2}O{sub eq}). The expansion of concrete prisms was studied immersed in simulated pore solution in order to address the limitations of conventional ASR testing methods, accelerated mortar bar test (AMBT) and concrete prism test (CPT). Expansion results demonstrate that 25% fly ash and 50% slag are both sufficient to mitigate ASR even with cements with alkali content up to 1% Na{sub 2}O{sub eq} and that the pore solution method is a viable alternative ASR testing method. Massive amounts of ASR products (~20 μm thickness) were observed in concretes without SCMs consistent with high degree of expansion and extensive cracking. Small amounts of ASR products (≤5 μm thickness) were also observed in concrete with SCMs despite absence of significant expansion.

36 MATERIALS SCIENCE↗

Submicron-scale mineralogy of lithotypes and the implications for trace element associations: Blue Gem coal, Knox County, Kentucky

Transmission electron microscopy accompanied by energy-dispersive spectroscopy and selected area electron diffraction of density-gradient separates from two lithotypes of the low-ash, low-sulfur Blue Gem coal, eastern Kentucky, revealed an array of previously unrecognized (in this coal, and arguable in most others) sub-micron minerals, some <10 nm in size. The first sample representing the 1.22–1.24 specific gravity fraction of the middle bench contains a mineral identified as a La-, Ce-, Nd-bearing monazite; other minerals with CrFe, CuFeS, FeZn-S, and Pb; and areas, probably comprising agglomerates of several grains, if not several minerals, with concentrations of Mg, Ca, Ti, Fe, Zn, Zr, and Mo. The second sample representing the 1.30–1.31 specific gravity fraction of the basal lithotype has aggregates of particles enriched in Mg, Ca, Ti, and Fe. Individual grains not specifically quantified include CrNiMnCuFeS, AgS, and CuS. Detailed investigation of one area (most of the variation within a <4 μm 2 region) demonstrates the presence of greenockite (CdS); minute phases containing NiCoGe and AgCdBi, the latter with a more evident S association than the former; metallic Bi; nisnite (Ni 3 Sn); silver cadmium; manganosite (MnO); and siderite. Some minerals, such as the monazite, are most likely of detrital or tuffaceous origin. Many of the other assemblages could be of hydrothermal origin, a hypothesis supported by known regional geochemical and coal rank trends, but not previously demonstrated in mineral assemblages at the 10's of nm scale in this region.

01 COAL, LIGNITE, AND PEAT↗

Reactivity deterioration of NiO/Al{sub 2}O{sub 3} oxygen carrier for chemical looping combustion of coal in a 10 kW{sub th} reactor

A relatively long-term experiment for chemical looping combustion of coal with NiO/Al{sub 2}O{sub 3} oxygen carrier was carried out in a 10 kW{sub th} continuous reactor of interconnected fluidized beds, and 100 h of operation was reached with the same batch of the oxygen carrier. The reactivity deterioration of the oxygen carriers was present during the experimental period. The reactivity deterioration of reacted oxygen carriers at different experimental stages was evaluated using X-ray diffraction (XRD), scanning electron microscope (SEM), and X-ray fluorescence spectrometer. SEM analysis showed no significant change in the morphology of the nickel-based oxygen carrier at the fuel reactor temperature {<=}940 C, but loss of surface area and porosity of reacted oxygen carriers was observed when the fuel reactor temperature exceeded 960 C. The results show that the sintering effect have mainly contributed to the reactivity deterioration of reacted oxygen carriers in the CLC process for coal, while the effects of coal ash and sulfur can be ignored. The oxidization of reduced oxygen carrier with air was an intensive exothermic process, and the high temperature of oxygen carrier particles led to sintering on the surface of oxygen carrier particles in the air reactor. Attention must be paid to control the external circulation of oxygen carrier particles in the interconnected fluidized beds in order to efficiently transport heat from the air reactor to the fuel reactor, and reduce the temperature of oxygen carrier particles in the air reactor. Improvement of reactivity deterioration of reacted oxygen carriers was achieved by the supplement of steam into the fuel reactor. Nevertheless, NiO/Al{sub 2}O{sub 3} is still one of the optimal oxygen carriers for chemical looping combustion of coal if the sintering of oxygen carrier is minimized at the suitable reactor temperature. (author)

01 COAL, LIGNITE, AND PEAT↗

Analysis of char-slag interaction and near-wall particle segregation in entrained-flow gasification of coal

The fate of carbon particles during entrained-flow gasification of coal in the slagging regime is analyzed. More specifically, the study addresses the relevance of segregation of carbon particles in a near-wall region of the gasifier to coal conversion. Segregation of carbon particles is analyzed considering the effects of turbulence- and swirl-promoted particle migration toward the wall, interaction of the impinging particles with the wall ash layer, coverage of the slag layer by refractory carbon particles, accumulation of carbon particles in a dense-dispersed phase near the wall of the gasifier. Operating conditions of the gasifier and slag properties may be combined so as to give rise to a variety of conversion regimes characterized by distinctively different patterns of carbon particles segregation. A simple 1D model of an entrained-flow gasifier has been developed based on the conceptual framework of carbon particle segregation. The model aims at providing a general assessment of the impact of the different patterns of carbon particle segregation on the course and extent of carbon gasification. A sensitivity analysis with reference to selected model parameters is performed to identify key processes controlling carbon segregation and their impact on the gasifier performance. (author)

01 COAL, LIGNITE, AND PEAT↗

Pressurized chemical-looping combustion of coal with an iron ore-based oxygen carrier

Chemical-looping combustion (CLC) is a new combustion technology with inherent separation of CO{sub 2}. Most of the previous investigations on CLC of solid fuels were conducted under atmospheric pressure. A pressurized CLC combined cycle (PCLC-CC) system is proposed as a promising coal combustion technology with potential higher system efficiency, higher fuel conversion, and lower cost for CO{sub 2} sequestration. In this study pressurized CLC of coal with Companhia Valedo Rio Doce (CVRD) iron ore was investigated in a laboratory fixed bed reactor. CVRD iron ore particles were exposed alternately to reduction by 0.4 g of Chinese Xuzhou bituminous coal gasified with 87.2% steam/N{sub 2} mixture and oxidation with 5% O{sub 2} in N{sub 2} at 970 C. The operating pressure was varied between 0.1 MPa and 0.6 MPa. First, control experiments of steam coal gasification over quartz sand were performed. H{sub 2} and CO{sub 2} are the major components of the gasification products, and the operating pressure influences the gas composition. Higher concentrations of CO{sub 2} and lower fractions of CO, CH{sub 4}, and H{sub 2} during the reduction process with CVRD iron ore was achieved under higher pressures. The effects of pressure on the coal gasification rate in the presence of the oxygen carrier were different for pyrolysis and char gasification. The pressurized condition suppresses the initial coal pyrolysis process while it also enhances coal char gasification and reduction with iron ore in steam, and thus improves the overall reaction rate of CLC. The oxidation rates and variation of oxygen carrier conversion are higher at elevated pressures reflecting higher reduction level in the previous reduction period. Scanning electron microscope and energy-dispersive X-ray spectroscopy (SEM-EDX) analyses show that particles become porous after experiments but maintain structure and size after several cycles. Agglomeration was not observed in this study. An EDX analysis demonstrates that there is very little coal ash deposited on the oxygen carrier particles but no appreciable crystalline phases change as verified by X-ray diffraction (XRD) analysis. Overall, the limited pressurized CLC experiments carried out in the present work suggest that PCLC of coal is promising and further investigations are necessary. (author)

01 COAL, LIGNITE, AND PEAT↗

Multimodal ultrafine particles from pulverized coal combustion in a laboratory scale reactor

Particle size distribution functions have been measured in a ethanol fueled flame reactor fed with a low amount of pulverized coal particles. The reactor is operated in low (5.0 vol.%) and high (76.5 vol.%) oxygen concentrations using two high volatile bituminous Colombian and Indonesian coals. A carbon black powder is also oxidized in the same conditions. Generated particles are sampled using rapid-dilution probes and the size distribution functions are measured on-line by a high resolution Differential Mobility Analyzer. Results clearly show that ultrafine particles, those with sizes lower than 100 nm, have a multimodal size distribution function. These particles have huge number concentrations in both investigated conditions whereas their formation is enhanced in the oxygen enriched condition. Ultrafine particles are almost totally dominated in number by the fraction having sizes below 30 nm. Nanoparticles also account for a significant fraction of total particle mass and slowly coagulate in the reactor. The shape of the size distribution functions is not affected by the coal type, at least for the two investigated coals. Results suggest that ultrafine particles form through the vaporization-nucleation-growth pathway involving inorganic ashes. Moreover the contribution of carbonaceous particles seems particularly important for size smaller than 5 nm. (author)

01 COAL, LIGNITE, AND PEAT↗

The importance of SO{sub 2} and SO{sub 3} for sulphation of gaseous KCl - An experimental investigation in a biomass fired CFB boiler

This paper is based on results obtained during co-combustion of wood pellets and straw in a 12 MW circulating fluidised bed (CFB) boiler. Elemental sulphur (S) and ammonium sulphate ((NH{sub 4}){sub 2}SO{sub 4}) were used as additives to convert the alkali chlorides (mainly KCl) to less corrosive alkali sulphates. Their performance was then evaluated using several measurement tools including, IACM (on-line measurements of gaseous alkali chlorides), a low-pressure impactor (particle size distribution and chemical composition of extracted fly ash particles), and deposit probes (chemical composition in deposits collected). The importance of the presence of either SO{sub 2} or SO{sub 3} for gas phase sulphation of KCl is also discussed. Ammonium sulphate performed significantly better than elemental sulphur. A more efficient sulphation of gaseous KCl was achieved with (NH{sub 4}){sub 2}SO{sub 4} even when the S/Cl molar ratio was less than half compared to sulphur. Thus the presence of gaseous SO{sub 3} is of greater importance than that of SO{sub 2} for the sulphation of gaseous KCl. (author)

09 BIOMASS FUELS↗