Search NASA⌕ Search

SEARCH · Search NASA

Results for “Azimuth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Measurement of Single- and Double-Spin Asymmetries in Deep Inelastic Pion Electroproduction with a Longitudinally Polarized Target

We report the first measurement of the transverse momentum dependence of double-spin asymmetries in semi-inclusive production of pions in deep-inelastic scattering off the longitudinally polarized proton. Data have been obtained using a polarized electron beam of 5.7 GeV with the CLAS detector at the Jefferson Lab (JLab). Modulations of single spin asymmetries over the azimuthal angle between lepton scattering and hadron production planes {phi} have been measured over a wide kinematic range in Bjorken x and virtual photon squared four-momentum Q{sup 2}. A significant nonzero sin2{phi} single spin asymmetry was observed for the first time indicating strong spin-orbit correlations for transversely polarized quarks in the longitudinally polarized proton.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Multiple-Wave Diffraction in High Energy Resolution Back-Reflecting X-Ray Optics

We have studied the effects of multiple-wave diffraction in a novel optical scheme recently published by Shvyd'ko et al. utilizing Bragg diffraction of x rays in backscattering geometry from asymmetrically cut crystals for achieving energy resolutions beyond the intrinsic width of the Bragg reflection. By numerical simulations based on dynamic x-ray diffraction and by experimentation involving two-dimensional angular scans of the back-reflecting crystal, multiple-wave diffraction was found to contribute up to several tens percent loss of efficiency but can be avoided without degrading the energy resolution of the original scheme by careful choice of azimuthal orientation of the diffracting crystal surface and by tilting of the crystal perpendicular to the dispersion plane.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Observations of Modified Three-Dimensional Instability Structure for Imploding z -Pinch Liners that are Premagnetized with an Axial Field

Novel experimental data are reported that reveal helical instability formation on imploding z -pinch liners that are premagnetized with an axial field. Such instabilities differ dramatically from the mostly azimuthally symmetric instabilities that form on unmagnetized liners. The helical structure persists at nearly constant pitch as the liner implodes. This is surprising since, at the liner surface, the azimuthal drive field presumably dwarfs the axial field for all but the earliest stages of the experiment. These fundamentally 3D results provide a unique and challenging test for 3D-magnetohydrodynamics simulations.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Constraints on the $\chi_\mathrm{c1}$ versus $\chi_\mathrm{c2}$ Polarizations in Proton-Proton Collisions at $\sqrt{s} =$ 8 TeV

The polarizations of promptly produced χc1 and χc2 mesons are studied using data collected by the CMS experiment at the LHC, in proton-proton collisions at s=8 TeV. The χc states are reconstructed via their radiative decays χc→J/ψγ, with the photons being measured through conversions to e+e−, which allows the two states to be well resolved. The polarizations are measured in the helicity frame, through the analysis of the χc2 to χc1 yield ratio as a function of the polar or azimuthal angle of the positive muon emitted in the J/ψ→μ+μ- decay, in three bins of J/ψ transverse momentum. While no differences are seen between the two states in terms of azimuthal decay angle distributions, they are observed to have significantly different polar anisotropies. The measurement favors a scenario where at least one of the two states is strongly polarized along the helicity quantization axis, in agreement with nonrelativistic quantum chromodynamics predictions. This is the first measurement of significantly polarized quarkonia produced at high transverse momentum.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Measurement of the Sensitivity of Two-Particle Correlations in $\mathcal{pp}$ Collisions to the Presence of Hard Scatterings

A key open question in the study of multiparticle production in high-energy pp collisions is the relationship between the “ridge”—i.e., the observed azimuthal correlations between particles in the underlying event that extend over all rapidities—and hard or semihard scattering processes. In particular, it is not known whether jets or their soft fragments are correlated with particles in the underlying event. To address this question, two-particle correlations are measured in pp collisions at $\sqrt{s}$=13 TeV using data collected by the ATLAS experiment at the LHC, with an integrated luminosity of 15.8 pb -1 , in two different configurations. In the first case, charged particles associated with jets are excluded from the correlation analysis, while in the second case, correlations are measured between particles within jets and charged particles from the underlying event. Second-order flow coefficients, v2, are presented as a function of event multiplicity and transverse momentum. These measurements show that excluding particles associated with jets does not affect the measured correlations. Moreover, particles associated with jets do not exhibit any significant azimuthal correlations with the underlying event, ruling out hard processes contributing to the ridge.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Observation of Medium-Induced Yield Enhancement and Acoplanarity Broadening of Low-𝑝T Jets from Measurements in 𝑝⁢𝑝 and Central Pb-Pb Collisions at $\sqrt{s_{NN}}$ = 5.02 TeV

The ALICE Collaboration reports the measurement of semi-inclusive distributions of charged-particle jets recoiling from a high transverse momentum (high p T ) hadron trigger in proton-proton and central Pb-Pb collisions at $\sqrt{s_{NN}}$ = 5.02 TeV. A data-driven statistical method is used to mitigate the large uncorrelated background in central Pb-Pb collisions. Recoil jet distributions are reported for jet resolution parameter R = 0.2, 0.4, and 0.5 in the range 7 < p T.jet < 140 GeV=c and trigger-recoil jet azimuthal separation π/2 < Δφ < π. The measurements exhibit a marked medium-induced jet yield enhancement at low p T and at large azimuthal deviation from Δφ ~ π. The enhancement is characterized by its dependence on Δφ, which has a slope that differs from zero by 4.7σ. Comparisons to model calculations incorporating different formulations of jet quenching are reported. These comparisons indicate that the observed yield enhancement arises from the response of the QGP medium to jet propagation.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Hard-photon-triggered jets in 𝑝−𝑝 and 𝐴−𝐴 collisions

An investigation of high-transverse-momentum (high-𝑝 𝑇 ) photon-triggered jets in proton-proton (𝑝−𝑝) and ion-ion (𝐴−𝐴) collisions at $\sqrt{s_{NN}}$=0.2 and 5.02TeV is carried out, using the multistage description of in-medium jet evolution. Monte Carlo simulations of hard scattering and energy loss in heavy-ion collisions are performed using parameters tuned in a previous study of the nuclear modification factor (𝑅 𝐴⁢𝐴 ) for inclusive jets and high-𝑝𝑇 hadrons. We obtain a good reproduction of the experimental data for photon-triggered jet 𝑅 𝐴⁢𝐴 , as measured by the ATLAS detector, the distribution of the ratio of jet to photon 𝑝 𝑇 (𝑋 𝐽⁢𝛾 ), measured by both CMS and ATLAS, and the photon-jet azimuthal correlation as measured by CMS. We obtain a moderate description of the photon-triggered jet 𝐼 𝐴⁢𝐴 , as measured by STAR. A noticeable improvement in the comparison is observed when one goes beyond prompt photons and includes bremsstrahlung and decay photons, revealing their significance in certain kinematic regions, particularly at 𝑋 𝐽⁢𝛾 >1. Moreover, azimuthal angle correlations demonstrate a notable impact of bremsstrahlung photons on the distribution, emphasizing their role in accurately describing experimental results. This work highlights the success of the multistage model of jet modification to straightforwardly predict (this set of) photon-triggered jet observables. This comparison, along with the role played by bremsstrahlung photons, has important consequences on the inclusion of such observables in a future Bayesian analysis.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

3D-Printed mmWave Quasi-Holographic Antenna for 2-D Beamforming

This paper presents the design and manufacturing of a novel 2D-scanning antenna that integrates a 3D-printed Rotman lens with a quasi-holographic leaky-wave antenna (HLWA). The proposed design achieved beam-scanning capabilities by leveraging the beamforming of the Rotman lens and the high-gain directive properties of the quasi-HLWA. The Rotman lens (RL) enables beam steering in the elevation plane by switching between input ports. The quasi-HLWA, designed using holographic principles, achieves frequency-controlled beam scanning in the azimuth plane. The entire antenna structure was fabricated using additive manufacturing with an Ink1092 substrate and silver ink for the conductive traces. This approach provides greater control over material placement and design freedom compared to traditional methods. A 25° transmission linear substrate taper was used to ensure good impedance matching between the Rotman lens and the quasi-HLWA, allowing greater gain while maintaining a good scanning range. The experimental results validate the 2D scanning capability of the proposed antenna. The antenna system provides coverage from −54° to 54° in the elevation θ plane and −28° to 28° in the azimuth plane ϕ , with a maximum measured gain of 21.3 dBi at 28 GHz with an average radiation efficiency η=60 %. The fabricated prototype was tested, and the performance was in good agreement with the simulated performance.

Rotman lens↗

ALTERNATIVE CONFIGURATION AND TIMING CONTROL FOR BEAM CHOPPING SYSTEM AT THE SNS LINAC

The Spallation Neutron Source (SNS) beam chopping system uses a segmented electrostatic lens in the Low Energy Beam Transport (LEBT) line to deflect the beam out of the Radio Frequency Quadrupole (RFQ) input aperture to create gaps in the 1 ms beam macro-pulse for extraction from the Ring, or fully displace the beam. The lens is split azimuthally into four quadrants which are pulsed independently by four bipolar high voltage pulse generators. The chopper timing control system creates trigger pulses to the pulse generators which deflect the beam sequentially to four positions on the chopper target. In the present chopper configuration, all four segments are powered simultaneously with a 1 MHz burst repetition rate within the macro-pulse. To improve chopping performance, faster switches and higher voltages are required. An alternative chopping system configuration which can meet this request has been proposed, where only two opposite segments are used at a time. This will facilitate pulse generator performance by reducing switching frequency and power dissipation in the high voltage switches while operating at increased voltages, and make beam deflection more effective, stable and reliable. The new chopping configuration requires changes in the LEBT timing control patterns, upgrading the pulse generator, and changing the azimuthal position of the lens segments in the LEBT structure.This paper will review the timing control patterns for present and suggested configurations, compare the pulse generator performance for both cases, and show the advantages of the new chopping modes. The results of the simulated beam distribution at the RFQ input for different deflecting voltages will also be presented.

Peplov, Vladimir↗

Test Results of the CERN HL-LHC low- Quadrupole Short Models MQXFS3c and MQXFS4

For the High Luminosity Upgrade of the CERN Large Hadron Collider, lower * quadrupole magnets based on advanced Nb3Sn conductors will be installed on each side of the ATLAS and CMS experiment insertion zones. As part of the technological developments needed to achieve the required field gradient of 132.6 T/m within a 150-mm aperture, short length model magnets, named MQXFS, are tested both at the CERN SM18 and FERMI Lab test facilities. The model magnets rely on two types of Nb3Sn conductors (RRP and PIT) and on an innovative bladders and keys design to provide mechanical support against the Lorentz forces. In 2016 and 2017, the powering tests of the first two models MQXFS3 (RRP) and MQXFS5 (PIT) proved that nominal performance (16.5 kA) could be reached with excellent memory of the quench current after thermal cycle. However both magnets showed a slow training behavior with clear observations of voltage disturbances before the quench. Besides MQXFS5 only could reach ultimate current (17.9 kA) whereas erratic behavior was observed on MQXFS3 due to conductor local degradation at the head of one of the coil. In 2018, this limiting coil was changed and the applied azimuthal pre-stress increased. If ultimate current could then be reached, no stable current could be maintained due to identified defect on the outer layer of the new coil. Finally the outcome of the test of the new model MQXFS4, featuring the final RRP conductors that will be used for the series production and variation on the inner layer quench heater designs are here reported in details.

43 PARTICLE ACCELERATORS↗

InSAR Time Series Analysis of L-Band Wide-Swath SAR Data Acquired by ALOS-2

We present that operating at L-band (24 cm wavelength) in wide-swath modes is one of the characteristics of the new and next generation satellite synthetic aperture radar (SAR) missions. After 3 years of operation, the Japan Aerospace Exploration Agency Advanced Land Observing Satellite-2 (ALOS-2) satellite has acquired a wealth of L-band wide-swath SAR data over many areas using its ScanSAR mode. We present interferometry SAR (InSAR) time series analysis results from ALOS-2 ScanSAR data. We analyze the possible error sources in the InSAR and correct them if possible. We present different time series analysis results including azimuth frequency modulation rate error, line of sight (LOS) ionospheric phase, azimuth shift caused by the ionosphere, and LOS displacement processed using both full-aperture and burst-by -burst workflows. The final InSAR LOS displacement time series result reveals both large-scale tectonic and small-scale anthropogenic deformation components. In conclusion, the results demonstrate the potential for measuring continental or even global-scale tectonic deformation and illustrate the promise of upcoming L-band wide-swath SAR missions, such as the NASA-ISRO SAR mission.

47 OTHER INSTRUMENTATION↗

CAMIS: A Cylindrical Active Mask Imaging System

Detecting and locating radiological and nuclear materials at distances of 10 m or more in urban and cluttered environments continues to pose challenges in nuclear security and proliferation detection. Previous approaches have focused on large-area radiation imaging using planar configurations of detectors and passive masks. However, these approaches suffer from limitations such as limited field-of-view (FOV) and reduced detection efficiency due to absorption in the mask. To address these limitations, we have developed the cylindrical active mask imaging system (CAMIS). This system comprises 128 NaI(Tl) (10 cm)3 detectors. These detectors are arranged in a cylindrical configuration, enabling gamma-ray imaging with a full 360° azimuthal FOV. The active mask elements within the system are arranged in a pseudorandom configuration, providing unique encoding for all incident directions within the FOV. CAMIS offers an effective detection area of approximately 1 m2 across the entire 360° FOV in the horizontal plane, achieving a mean angular resolution of 10.9° in the azimuthal direction and 12.9° in the polar direction measured by taking the full-width at half-maximum (FWHM) of a cross-section at the maximum reconstructed intensity.

Lamb, C↗

Analytical Solution for Three-Dimensional, Unsteady Heat Conduction in a Multilayer Sphere

An analytical solution has been obtained for the transient problem of three-dimensional multilayer heat conduction in a sphere with layers in the radial direction. The solution procedure can be applied to a hollow sphere or a solid sphere composed of several layers of various materials. In general, the separation of variables applied to 3D spherical coordinates has unique characteristics due to the presence of associated Legendre functions as the eigenfunctions. Moreover, an eigenvalue problem in the azimuthal direction also requires solution; again, its properties are unique owing to periodicity in the azimuthal direction. Therefore, extending existing solutions in 2D spherical coordinates to 3D spherical coordinates is not straightforward. In a spherical coordinate system, one can solve a 3D transient multilayer heat conduction problem without the presence of imaginary eigenvalues. A 2D cylindrical polar coordinate system is the only other case in which such multidimensional problems can be solved without the use of imaginary eigenvalues. The absence of imaginary eigenvalues renders the solution methodology significantly more useful for practical applications. The methodology described can be used for all three types of boundary conditions in the outer and inner surface of the sphere. Lastly, the solution procedure is demonstrated on an illustrative problem for which results are obtained.

36 MATERIALS SCIENCE↗

Early Time Evolution of Circumferential Perturbation of Initial Particle Volume Fraction in Explosive Cylindrical Multiphase Dispersion

When an annular bed of solid particles that surrounds a cylindrical high-energy explosive core gets radially dispersed after detonation, the expanding front of particles undergoes instabilities. One of the possible causes of the instabilities is an inhomogeneous initial distribution of particles. This study explores this possibility by introducing two-dimensional perturbations to the initial distribution of particles within the annular bed and quantifying the growth of these perturbations over time using two-dimensional simulations. The initial perturbations are in the form of superposition of up to three sinusoidal azimuthal modal variations in the initial particle volume fraction (PVF, ratio of particle to cell volume). These are observed to impact the particle distribution at later times through a channeling instability whose effects are: (i) to decrease the velocity in regions of larger particle volume (PV) and (ii) to facilitate circumferential particle migration into the slow moving high PV sectors. These departures from axisymmetry are quantified by introducing two metrics. The effect of varying the number of azimuthal modes contained in the initial PVF perturbation, along with their amplitudes, wavelengths, and relative phases is investigated. The proposed metrics do not vary substantially with the relative phases; however, there is a strong variation in the metrics due to changes in the wavenumber. Unimodal perturbations were found to amplify both metrics the most.

Engineering↗

Significance of the Direct Excitation Mechanism for High-Frequency Response of Premixed Flames to Flow Oscillations

Premixed flames are sensitive to flow disturbances, which can arise from acoustic or vortical fluctuations. For transverse instabilities, it is known that a dominant mechanism for flame response is “injector coupling,” whereby pressure oscillations associated with transverse waves excite axial flow disturbances. These axial flow disturbances then excite heat release oscillations. The objective of this paper is to consider another mechanism—the direct sensitivity of the unsteady heat release to transverse acoustic waves—and to compare its significance relative to the induced axial disturbances, in a linear framework. The rate at which the flame adds energy to the disturbance field is quantified using the Rayleigh criterion and evaluated over a range of control parameters, such as flame length and swirl number. The results show that radial modes induce heat release fluctuations that always add energy to the acoustic field, whereas heat release fluctuations induced by mixed radial-azimuthal modes can add or remove energy. These amplification rates are then compared to the flame response from induced axial fluctuations. For combustor-centered flames, these results show that the direct excitation mechanism has negligible amplification rates relative to the induced axial mechanism for radial modes. For transverse modes, the fact that the nozzle is located at a pressure node indicates that negligible induced axial velocity disturbances are excited; as such, the direct mechanism dominates. As a result, for flames that are not centered on pressure nodes, the direct mechanism for mixed modes dominates for certain nozzle locations and flame angles.

42 ENGINEERING↗

Identification of High-Frequency Transverse Acoustic Modes in Multi-Nozzle Can Combustors

Abstract High frequency thermoacoustic instabilities are problematic for lean-premixed gas turbines. Identifying which acoustic mode is being excited is important, in that it provides insight into potential mitigation measures and mechanical stress/life. However, the frequency spacing between modes becomes quite close for high frequency instabilities in a can combustor. This makes it difficult to distinguish between the modes (e.g., the first transverse mode vs. a higher order axial/mixed mode) based upon frequency calculations alone, which inevitably have uncertainties in boundary conditions, temperature profiles, and combustion response. This paper presents a methodology to simultaneously identify the acoustic mode shapes in the axial and azimuthal directions from acoustic pressure measurements. Multiple high temperature pressure transducers, located at distinct axial and azimuthal positions, are flush mounted in the combustor wall. The measured pressure oscillations from each sensor are then used to reconstruct the pressure distributions by using a least squares method in conjunction with a solution of a three dimensional wave equation. In order to validate the methodology, finite element method (FEM) calculations with estimated post-flame temperature is used to provide the candidate frequencies and corresponding mode shapes. The results demonstrate the reconstructed mode shapes and standing/spinning character of transverse waves, as well as the associated frequencies, both of which are consistent with the FEM predictions. Nodal line location was also extracted from the experimental data during the instabilities in the pressure data.

Kim, J.↗

Optimum Injector Parameters for Thermoacoustic Stability in a Multi-Nozzle Can Combustion System

Abstract High-frequency transverse instabilities are an important concern in can combustor configurations. In these configurations which are typically operated with multiple injectors around a central injector, each injector is subjected to different parts of the acoustic mode shape and thus respond differently for the same instability mode. Recent work by the author has modeled the response of premixed flames to excitation by natural high-frequency transverse modes in a can combustor both in the center and outer nozzles. The stability of these acoustically non-compact flames was assessed using the Rayleigh criterion (Rayleigh Integral denoted as RI) and not the overall unsteady heat release as is the case for compact flames. Several key control parameters were studied, namely — flame angle, swirling strength, nozzle location. For non-axisymmetric modes such as the commonly occurring 1-T mode, both radial and azimuthal offsets of the nozzle location affected stability. The framework was applied to an optimization study to identify the optimal combination of parameters that minimizes RI for the different nozzles in the multi-nozzle system. In this study, a N-around-1 configuration was studied, and the results indicated that the different nozzles needed to be operated at different flame angles and swirl numbers to result in an overall minimum RI. However, the specific response of the different injectors was not considered. The helical mode distribution at each injector varies as we azimuthally go around the combustor’s injector distribution and thus the most amplified mode and the resulting flame response would be different. To minimize RI, it is important to determine the injector configurations that result in a hydrodynamic profile that minimizes the individual RI for each nozzle. The resulting relationship between the injector’s flow and local hydrodynamics can then be used in a hydrodynamics study of an individual injector so that the most optimal injector is chosen depending on its location in the combustor dump plane.

Acharya, Vishal↗