Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composite Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Application of a Rapid Design Tool to a 3D Woven Structural Joint

The optimization of composite structural joints is an iterative process and a multiscale problem. High fidelity finite element modeling of joints with 3D woven and laminated materials can become computationally expensive. The aim of this paper is to establish a reliable analysis process for the optimization of a composite Y-joint (curved Pi-joint), to be used in an aircraft fuselage, using commercial rapid joint design, analysis, and optimization software. The rapid joint design tool was investigated as a substitute and/or complement to a finite element analysis software. A composite Pi-joint and a composite Y-joint were evaluated using the rapid joint design tool to determine the applicability and limits of the software. Furthermore, three main preliminary parametric studies were performed to better understand the capability of the tool in predicting the stress distributions and trends in the Y-joint. The parameters investigated were the joint curvature, the laminated skin thickness, the adhesive systems, and the ply composition. Lastly, trends in predicted failure load were produced as a function of skin thickness (16ply, 24ply and 32ply). Failure loads were found with varying joint curvature and skin thickness using stress-based adherend failure criterion. The rapid joint design tool was also validated against existing experimental results.

Bonded Joints↗

Structurally-continuous composite corners

Flat composite materials are cut at certain angles to form boxes with corners as thick as walls. Patterns produce uniform corners, and cuts are structured so that shear loads are transferred from ply to ply instead of across one surface.

Jackson, A. C.↗

Design and Analysis for the Carbon Fiber Composite Support Structure for Layer 0 of the D0 Silicon Micro Tracker

The support structures for the new Layer 0 (Figures 1, 2, 3) of the Run 2b silicon tracker in D0 were designed and fabricated at the University of Washington. These structures were required to have minimum mass, yet be very rigid so as to meet the high precision requirements placed on the position of the silicon detector chips. They also have to provide for cooling to remove the heat generated by the sensors and signal processing electronics and to keep the sensors at the desired operating temperature (below -5 C). All of these requirements were best met by carbon fiber/epoxy composite technology. State of the art carbon fiber materials have extremely high Young's moduli and high thermal conductivity. Appropriate fiber lay-ups and fabrication methods have been developed and used successfully to produce both various prototype structures and the structures used in the production Layer 0. The geometry of these structures was determined mainly by the geometry of the sensors themselves. The structures incorporated a complete cooling system consisting of extruded PEEK coolant tubes and distribution manifolds made from carbon fiber composites. In order to determine the mechanical and thermal performance of the structures, detailed FEA analyses of L0 have been carried out and are described.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modeling the interfacial failure and resulting mechanical properties of z-pinned additively manufactured composites

The mechanical properties of Fused Filament Fabrication (FFF) parts are limited in the build direction, albeit advantages such as design flexibility and in-house customization. Here, in this paper, a novel z-pinning approach that enhances mechanical properties in the build direction by depositing material across multiple layers within the part was investigated through numerical simulations and validated experimentally. A finite element model for z-pinned composite structures was developed by assigning fiber-orientation dependent material properties obtained using a micromechanics approach to beads and pins. The bead-to-bead and pin-to-pin adhesions within the z-pinned structures were modeled using a cohesive traction separation law. The properties of cohesive elements for carbon fiber-reinforced polylactic acid (CF-PLA) z-pinned composites were calibrated using tensile experiments. The elastic modulus and tensile strength of CF-PLA z-pinned composites in the build direction were predicted with the developed numerical model. The numerical investigation on various geometrical parameters revealed that the largest pin volume increases the stiffness and tensile strength by 40% and thus, has the greatest influence on the mechanical properties of the z-pinned composites. The effect of z-pin geometrical parameters on the mechanical properties was summarized to aid in the design of z-pinned additively manufactured composite structures.

36 MATERIALS SCIENCE↗

Electronic structure manipulation via composition tuning for the development of highly conductive and acid-stable oxides

Exploring materials that simultaneously possess high conductivity and electrochemical stability is critical for various energy-conversion applications. In this study, our combined computations and experiments suggest the Mg–Ti–O chemical space for novel ternary oxide compounds offering high electrical conductivity and corrosion stability in acidic conditions to be potentially used as catalyst supporter of polymer electrolyte membrane fuel cells. High electrical conductivity (6.09 × 10 -1 S cm -1 ) is achieved at room temperature by tuning the chemical composition of Mg 1-x Ti 2+x O 5 while still maintaining good corrosion stability (1.2 × 10 -4 mA cm -2 after six days) in acidic conditions. Furthermore, we discover that a reducing gas environment during the synthesis increases the Ti solubility in Mg 1-x Ti 2+x O 5 with a reduced valence state of Ti, thus resulting in high conductivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nanometer scale structural and compositional inhomogeneities of half-Heusler CoTi 1-x Fe x Sb thin films

The correlative use of X-ray diffraction (XRD), scanning transmission electron microscopy (STEM), and atom probe tomography (APT) allows the structure of substitutionally alloyed half-Heusler compound CoTi 1-x Fe x Sb to be characterized at the nanometer scale. For x = 0.2, 0.3, and 0.5, XRD patterns indicate an epitaxial cube-on-cube growth with no detectable secondary phases and are suggestive of high crystalline quality for all three of the films. This is supported using atomic resolution STEM images, which revealed the absence of secondary phases or polycrystalline regions, thus confirming the half-Heusler structure of the CoTi 1-x Fe x Sb films. For all three samples, the APT reconstructions were optimized to resolve the atomic planes in the [001] growth direction allowing the exploitation of reliable datasets. We note the presence of Fe-rich phases in the samples with Fe atoms sitting on Ti crystallographic sites is revealed. A strong phase separation is observed for x = 0.2 and x = 0.3 and is almost no longer observed for x = 0.5 in good agreement with the magnetic properties of the films.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The composition and structure of white dwarf atmospheres revealed by extreme ultraviolet spectroscopy

The ROentgen SATellite (ROSAT) and Extreme UltraViolet Explorer (EUVE) all-sky surveys have resulted in an important change in our understanding of the general composition of hydrogen-rich DA white dwarf atmospheres, with the photospheric opacity dominated by heavy elements rather than helium in the hottest stars (T > 40, 000 K). Most stars cooler than 40,000 K have more or less pure H atmospheres. However, one question, which has not been resolved, concerned the specific nature of the heavy elements and the role of helium in the hottest white dwarfs. One view of white dwarf evolution requires that H-rich DA stars form by gravitational settling of He from either DAO or He-rich central stars of planetary nebulae. In this case, the youngest (hottest) DA white dwarfs may still contain visible traces of He. Spectroscopic observations now available with EUVE provide a crucial test of these ideas. Analysis of data from the EUVE Guest Observer programme and EUVE public archive allows quantitative consideration of the sources of EUV opacity and places limits on the abundance of He which may be present.

Barstow, Martin A.↗

In-flight environmental effects on airplane composite vertical fin caps

The NASA-Langley Storm Hazards Program has given attention to the effects of severe in-flight weather environments on composite structures, using an instrumented F-106B in storm penetration experiments. The vertical fin cap was chosen for the study of lightning strike attachments on composite structures of four different types: (1) glass/epoxy with flame-sprayed aluminum; (2) Kevlar/epoxy with aluminized glass cloth; (3) graphite-epoxy without lightning protection; and (4) unprotected graphite-epoxy with electrical isolation from the rest of the aircraft structure. Flight test results are evaluated.

Howell, William E.↗

STRUCTURE AND COMPOSITION OF TWO TRANSITIONAL CIRCUMSTELLAR DISKS IN CORONA AUSTRALIS

The late stages of evolution of the primordial circumstellar disks surrounding young stars are poorly understood, yet vital to constraining theories of planet formation. We consider basic structural models for the disks around two {approx}10 Myr old members of the nearby RCrA association: RX J1842.9-3532 and RX J1852.3-3700. We present new arcsecond-resolution maps of their 230 GHz continuum emission from the Submillimeter Array and unresolved CO(3-2) spectra from the Atacama Submillimeter Telescope Experiment. By combining these data with broadband fluxes from the literature and infrared fluxes and spectra from the catalog of the Formation and Evolution of Planetary Systems Legacy program on the Spitzer Space Telescope, we assemble a multiwavelength data set probing the gas and dust disks. Using the Monte Carlo radiative transfer code RADMC to model simultaneously the spectral energy distribution and millimeter continuum visibilities, we derive basic dust disk properties and identify an inner cavity of radius 16 AU in the disk around RX J1852.3-3700. We also identify an optically thin 5 AU cavity in the disk around RX J1842.9-3532, with a small amount of optically thick material close to the star. The molecular line observations suggest an intermediate disk inclination in RX J1842.9-3532, consistent with the continuum emission. In combination with the dust models, the molecular data allow us to derive a lower CO content than expected, suggesting that the process of gas clearing is likely underway in both systems, perhaps simultaneously with planet formation.

79 ASTRONOMY AND ASTROPHYSICS↗

High performance structural laminate composite material for use to 1000.degree. F. and above, apparatus for and method of manufacturing same, and articles made with same

A novel materials technology has been developed and demonstrated for providing a high modulus composite material for use to 1000.degree. F. and above. This material can be produced at 5-20% of the cost of refractory materials, and has higher structural properties. This technology successfully resolves the problem of thermal shock or ply lift, which limits traditional high temperature laminates (such as graphite/polyimide and graphite/phenolic) to temperatures of 550-650.degree. F. in thicker (0.25 and above) laminates. The technology disclosed herein is an enabling technology for the nose for the External Tank (ET) of the Space Shuttle, and has been shown to be capable of withstanding the severe environments encountered by the nose cone through wind tunnel testing, high temperature subcomponent testing, and full scale structural, dynamic, acoustic, and damage tolerance testing.

Seal, Ellis C.↗

Empirical Characterization and Modeling of Cohesive – to – Adhesive Shear Fracture Mode Transition due to Increased Adhesive Layer Thicknesses of Fiber Reinforced Composite Single – Lap Joints

Here, to ensure a strong adhesive bond, most standards and adhesive manufacturers specify a maximum adhesive gap of 1 mm when bonding fiber reinforced composite structures. In manufacturing large components, such as joining two halves of wind turbine blades, meeting this gap tolerance specification is impractical; gaps larger than 10 mm are common in large adhesively bonded composite structures using state-of-the-art manufacturing techniques. Currently, there is a lack of fundamental understanding of the failure mechanics of adhesive gaps larger than 3 mm. To create such understanding, glass fiber - acrylic thermoplastic composite panels bonded using different epoxy adhesives within single-lap joint samples with adhesive thicknesses of 0.1 mm, 0.3 mm, 1 mm, 3 mm, 5 mm, and 10 mm were sheared to failure. A transition from cohesive to adhesive failure was observed to occur about 1 mm to 3 mm joint thicknesses. Plotting the shear stress normalized by the ratio of the joint width to thickness as a function of the joint thickness normalized by the joint length is shown to result in the ability to fit simple empirically derived models of the cohesive-to-adhesive failure transition, regardless of the adhesive. Furthermore, using these normalized variables, all the observed cohesively failed specimens collapse to a single master curve, as do the adhesively failed specimens.

36 MATERIALS SCIENCE↗

In-Situ Consolidation Automated Fiber Placement of Thermoplastic Composites for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) initiated the Hi-Rate Composites Aircraft Manufacturing (HiCAM) project in 2021 with the goal of significantly increasing composite structures manufacturing rate in the commercial aircraft industry. The technologies currently under investigation include resin infusion and automated fiber placement (AFP) of novel thermoset materials and thermoplastic composites. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA is particularly focused on assessing composite structure manufacturing utilizing an in-situ consolidation AFP of thermoplastics (ICAT) process employing a recently developed laser heating system. Two semi-crystalline polyaryletherketone thermoplastic tape materials were characterized to ascertain the ICAT process parameters at AFP placement speeds approaching 423 mm/s. The required laser power settings were determined at Electroimpact, measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. An overview of the HiCAM project as well as initial data from ICAT process characterizations are described.

thermoplastic composites↗

In-Situ Consolidation Automated Fiber Placement of Thermoplastic Composites for High-Rate Aircraft Manufacturing

The National Aeronautics and Space Administration (NASA) initiated the Hi-Rate Composites Aircraft Manufacturing (HiCAM) project in 2021 with the goal of significantly increasing composite structures manufacturing rate in the commercial aircraft industry. The technologies currently under investigation include resin infusion and automated fiber placement (AFP) of novel thermoset materials and thermoplastic composites. Thermoplastic composites offer attractive solutions to rapid manufacturing due to their ability to be formed and consolidated quickly. NASA is particularly focused on assessing composite structure manufacturing utilizing an in-situ consolidation AFP of thermoplastics (ICAT) process employing a recently developed laser heating system. Two semi-crystalline polyaryletherketone thermoplastic tape materials were characterized to ascertain the ICAT process parameters at AFP placement speeds approaching 423 mm/s. The required laser power settings were determined at Electroimpact, measuring material temperatures utilizing a forward looking infrared (FLIR) thermal imaging camera and thermocouples. The material temperature, tool temperature, and placement speed were varied for resulting consolidation quality assessment. The resulting temperature data were also utilized to calibrate thermal analysis models under development at NASA. The experimental temperature data confirmed analytical results. An overview of the HiCAM project as well as initial data from ICAT process characterizations are described.

laser heating↗

Ultrasonic Nondestructive Evaluation Techniques Applied to the Quantitative Characterization of Textile Composite Materials

In this Progress Report, we describe our recent developments of advanced ultrasonic nondestructive evaluation methods applied to the characterization of anisotropic materials. We present images obtained from experimental measurements of ultrasonic diffraction patterns for a thin woven composite in an immersion setup. In addition, we compare apparent signal loss measurements of the thin woven composite for phase-sensitive and phase-insensitive detection methods. All images of diffraction patterns have been included on the accompanying CD-ROM in the Adobe(Trademark) Portable Document Format (PDF). Due to the extensive amount of data, however, hardcopies of only a small representative selection of the images are included within the printed report. This Progress Report presents experimental results that support successful implementation of single element as well as one and two-dimensional ultrasonic array technologies for the inspection of textile composite structures. In our previous reports, we have addressed issues regarding beam profiles of ultrasonic pressure fields transmitted through a water reference path and transmitted through a thin woven composite sample path. Furthermore, we presented experimental results of the effect of a thin woven composite on the magnitude of an insonifying ultrasonic pressure field. In addition to the study of ultrasonic beam profiles, we consider issues relevant to the application of single-element, one-dimensional, and two-dimensional array technologies towards probing the mechanical properties of advanced engineering composites and structures. We provide comparisons between phase-sensitive and phase-insensitive detection methods for determination of textile composite structure parameters. We also compare phase-sensitive and phase-insensitive - - ---- ----- apparent signal loss measurements in an effort to study the phenomenon of phase cancellation at the face of a finite-aperture single-element receiver. Furthermore, in this Progress Report we extend our work on ultrasonic beam profile issues through investigation of the phase fronts of the pressure field. In Section H of this Progress Report we briefly describe the experimental arrangement and methods for data acquisition of the ultrasonic diffraction patterns upon transmission through a thin woven composite. Section III details the analysis of the experimental data followed by the experimental results in Section IV. Finally, a discussion of the observations and conclusions is found in Section V.

Miller, James G.↗

Ultrasonic Characterization of Fatigue Cracks in Composite Materials

Microcracking in composite structures due to combined fatigue and cryogenic loading can cause leakage and failure of the structure and can be difficult to detect in-service. In aerospace systems, these leaks may lead to loss of pressure/propellant, increased risk of explosion and possible cryo-pumping. The success of nondestructive evaluation to detect intra-ply microcracking in unlined pressure vessels fabricated from composite materials is critical to the use of composite structures in future space systems. The work presented herein characterizes measurements of intraply fatigue cracking through the thickness of laminated composite material by means of correlation with ultrasonic resonance. Resonant ultrasound spectroscopy provides measurements which are sensitive to both the microscopic and macroscopic properties of the test article. Elastic moduli, acoustic attenuation, and geometry can all be probed. The approach is based on the premise of half-wavelength resonance. The method injects a broadband ultrasonic wave into the test structure using a swept frequency technique. This method provides dramatically increased energy input into the test article, as compared to conventional pulsed ultrasonics. This relative energy increase improves the ability to measure finer details in the materials characterization, such as microcracking and porosity. As the microcrack density increases, more interactions occur with the higher frequency (small wavelength) components of the signal train causing the spectrum to shift toward lower frequencies. Several methods are under investigation to correlate the degree of microcracking from resonance ultrasound measurements on composite test articles including self organizing neural networks, chemometric techniques used in optical spectroscopy and other clustering algorithms.

Workman, Gary L.↗

Structure, Morphology, and Assembly Behavior of Kafirin

Prolamins from grains have attracted intensive attention in recent years due to their potential in satisfying the demand for environmentally friendly (biodegradable), abundantly available (sustainable), and cost-effective biomaterials. However, for kafirin, the prolamin from sorghum, its composition, structure, morphology, and self-assembly behaviors have not been fully characterized. In this paper, kafirin was extracted from the whole sorghum grain and found to contain 68, 14, 6, and 12% of α-, β-, and γ-fractions and cross-linked kafirin, respectively. Freeze-dried kafirin contained ~49% α-helix in the solid state. When dissolved in 65% (v/v) isopropanol, 60% (v/v) tert-butanol, and 85% (v/v) ethanol aqueous solvents, the relative α-helix content in kafirin increased with the decrease of solvent polarity. Structural analysis using small-angle X-ray scattering (SAXS) indicated that kafirin (2 mg/mL) took stretched and extended conformations with dimensions of 118 × 15 × 15 and 100 × 11 × 11 Å in 60% tert-butanol and 65% isopropanol, respectively. More elongated conformation of individual kafirin with high-order assembly was observed in 85% ethanol. Protein aggregation occurred as protein concentration increased in its good solvent. The morphology of kafirin assemblies captured by atomic force microscopy (AFM) revealed that kafirin protein took uniform particle morphology at low concentration, and disk-like or rod-like structures resulting from solvent evaporation induced particle interactions emerged at high concentrations. These results suggest that both protein concentration and solvent polarity can effectively regulate kafirin assemblies from thick rod-like to slim rod-like structures, a convenient way to tune the fibrillation of prolamin-based biomaterials.

60 APPLIED LIFE SCIENCES↗

Detection of Delamination in Composite Beams Using Broadband Acoustic Emission Signatures

Delamination in composite structure may be caused by imperfections introduced during the manufacturing process or by impact loads by foreign objects during the operational life. There are some nondestructive evaluation methods to detect delamination in composite structures such as x-radiography, ultrasonic testing, and thermal/infrared inspection. These methods are expensive and hard to use for on line detection. Acoustic emission testing can monitor the material under test even under the presence of noise generated under load. It has been used extensively in proof-testing of fiberglass pressure vessels and beams. In the present work, experimental studies are conducted to investigate the use of broadband acoustic emission signatures to detect delaminations in composite beams. Glass/epoxy beam specimens with full width, prescribed delamination sizes of 2 inches and 4 inches are investigated. The prescribed delamination is produced by inserting Teflon film between laminae during the fabrication of composite laminate. The objectives of this research is to develop a method for predicting delamination size and location in laminated composite beams by combining smart materials concept and broadband AE analysis techniques. More specifically, a piezoceramic (PZT) patch is bonded on the surface of composite beams and used as a pulser. The piezoceramic patch simulates the AE wave source as a 3 cycles, 50KHz, burst sine wave. One broadband AE sensor is fixed near the PZT patch to measure the AE wave near the AE source. A second broadband AE sensor, which is used as a receiver, is scanned along the composite beams at 0.25 inch step to measure propagation of AE wave along the composite beams. The acquired AE waveform is digitized and processed. Signal strength, signal energy, cross-correlation of AE waveforms, and tracking of specific cycle of AE waveforms are used to detect delamination size and location.

Okafor, A. C.↗