Results for “Engine efficiency” — Page 65

NASA NTRS2008

Advanced Low Conductivity Thermal Barrier Coatings: Performance and Future Directions (Invited paper)

Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. In this presentation, thermal barrier coating development considerations and performance will be emphasized. Advanced thermal barrier coatings have been developed using a multi-component defect clustering approach, and shown to have improved thermal stability and lower conductivity. The coating systems have been demonstrated for high temperature combustor applications. For thermal barrier coatings designed for turbine airfoil applications, further improved erosion and impact resistance are crucial for engine performance and durability. Erosion resistant thermal barrier coatings are being developed, with a current emphasis on the toughness improvements using a combined rare earth- and transition metal-oxide doping approach. The performance of the toughened thermal barrier coatings has been evaluated in burner rig and laser heat-flux rig simulated engine erosion and thermal gradient environments. The results have shown that the coating composition optimizations can effectively improve the erosion and impact resistance of the coating systems, while maintaining low thermal conductivity and cyclic durability. The erosion, impact and high heat-flux damage mechanisms of the thermal barrier coatings will also be described.

Zhu, Dongming↗

NASA NTRS2008

Advanced Low Conductivity Thermal Barrier Coatings: Performance and Future Directions

Thermal barrier coatings will be more aggressively designed to protect gas turbine engine hot-section components in order to meet future engine higher fuel efficiency and lower emission goals. In this presentation, thermal barrier coating development considerations and performance will be emphasized. Advanced thermal barrier coatings have been developed using a multi-component defect clustering approach, and shown to have improved thermal stability and lower conductivity. The coating systems have been demonstrated for high temperature combustor applications. For thermal barrier coatings designed for turbine airfoil applications, further improved erosion and impact resistance are crucial for engine performance and durability. Erosion resistant thermal barrier coatings are being developed, with a current emphasis on the toughness improvements using a combined rare earth- and transition metal-oxide doping approach. The performance of the toughened thermal barrier coatings has been evaluated in burner rig and laser heat-flux rig simulated engine erosion and thermal gradient environments. The results have shown that the coating composition optimizations can effectively improve the erosion and impact resistance of the coating systems, while maintaining low thermal conductivity and cyclic durability. The erosion, impact and high heat-flux damage mechanisms of the thermal barrier coatings will also be described.

Zhu, Dongming↗

DOE OSTI2018

Requirements Efficiency: External Questionnaire Results

Efficiency in requirements engineering and management (REM) for complex hardware systems is desirable to reduce program impacts, such as schedule and budget. Sandia National Labs (SNL) investigated external state-of-the-practice REM to capture insights, recommendations, and best practices from external entities on several REM topics. Twenty-one at-will participants contributed responses to closed- and open-ended questions. The results were synthesized and are provided herein. The results help SNL and others to understand where its practices are current; what trends, approaches, or processes in REM might be beneficial if implemented or introduced; what challenges might be avoided; where efficiencies might be realized; and which practices are still maturing or evolving in industry and academia, so that SNL can stay abreast of these developments.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

NASA NTRS1997

Single-Lever Power Control for General Aviation Aircraft Promises Improved Efficiency and Simplified Pilot Controls

General aviation research is leading to major advances in internal combustion engine control systems for single-engine, single-pilot aircraft. These advances promise to increase engine performance and fuel efficiency while substantially reducing pilot workload and increasing flight safety. One such advance is a single-lever power control (SLPC) system, a welcome departure from older, less user-friendly, multilever engine control systems. The benefits of using single-lever power controls for general aviation aircraft are improved flight safety through advanced engine diagnostics, simplified powerplant operations, increased time between overhauls, and cost-effective technology (extends fuel burn and reduces overhaul costs). The single-lever concept has proven to be so effective in preliminary studies that general aviation manufacturers are making plans to retrofit current aircraft with the technology and are incorporating it in designs for future aircraft.

Musgrave, Jeffrey L.↗

DOE OSTI2021

Numerical investigation of a fueled pre-chamber spark-ignition natural gas engine

Pre-chamber spark-ignition (PCSI) is a leading advanced ignition concept for internal combustion engines with the potential to enable diesel-like efficiency in medium-duty/heavy-duty (MD/HD) natural gas (NG) engines. By leveraging distributed ignition sources from multiple turbulent jets, the PCSI technology can deliver extremely short combustion duration in ultra-lean mixtures and significantly improve the engine thermal efficiency. However, in the automotive industry there is a lack of adequate science base and predictive simulation tools required for commercial development of PCSI engines. Here, in this study, Reynolds-Average Navier-Stokes simulations are carried out to describe the combustion process in lean-burn NG engines, focusing on the combustion modeling approach. Two combustion models, multi-zone well-stirred reactor (MZ-WSR) and G-equation, are used to simulate the combustion process in an MD NG engine equipped with a fueled-PCSI system for four operating conditions close to the lean operating limit. A skeletal chemical mechanism and a laminar flame speed tabulation are used to compute the combustion accurately. Simulation results are compared with experimental data regarding measured cylinder pressure, heat release rate, and combustion duration. By dividing the PCSI combustion process into four distinct phases, the difference between the two models’ results for each phase is analyzed in detail. The MZ-WSR model overestimates the combustion duration for early flame kernel growth in the pre-chamber due to the lack of a specific formulation to take turbulence-chemistry interaction into account. Despite the prolonged combustion duration and low pressure built-up inside the pre-chamber, the model matches the combustion rate in the main-chamber. In contrast, the G-equation model delivers good agreements for the pre-chamber combustion and turbulent jet-driven combustion processes. However, the model starts to underestimate the combustion rate in the main-chamber, especially under ultra-lean mixture conditions. Finally, improvements are needed for both models to simulate the later combustion stage that occurred in the near-wall regions.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS1978

Substitution of ceramics for high temperature alloys

The high temperature capability of ceramics such as silicon nitride and silicon carbide can result in turbine engines of improved efficiency. Other advantages when compared to the nickel and cobalt alloys in current use are raw material availability, lower weight, erosion/corrosion resistance, and potentially lower cost. The use of ceramics in three different sizes of gas turbine is considered; these are the large utility turbines, advanced aircraft turbines, and small automotive turbines. Special consideration, unique to each of these applications, arise when one considers substituting ceramics for high temperature alloys. The effects of material substitutions are reviewed in terms of engine performance, operating economy, and secondary effects.

Probst, H. B.↗

DOE OSTI2017

Can We Practically Bring Physics-based Modeling Into Operational Analytics Tools?

We present that analytics software is increasingly used to improve and maintain operational efficiency in commercial buildings. Energy managers, owners, and operators are using a diversity of commercial offerings often referred to as Energy Information Systems, Fault Detection and Diagnostic (FDD) systems, or more broadly Energy Management and Information Systems, to cost-effectively enable savings on the order of ten to twenty percent. Most of these systems use data from meters and sensors, with rule-based and/or data-driven models to characterize system and building behavior. In contrast, physics-based modeling uses first-principles and engineering models (e.g., efficiency curves) to characterize system and building behavior. Historically, these physics-based approaches have been used in the design phase of the building life cycle or in retrofit analyses. Researchers have begun exploring the benefits of integrating physics-based models with operational data analytics tools, bridging the gap between design and operations. In this paper, we detail the development and operator use of a software tool that uses hybrid data-driven and physics-based approaches to cooling plant FDD and optimization. Specifically, we describe the system architecture, models, and FDD and optimization algorithms; advantages and disadvantages with respect to purely data-driven approaches; and practical implications for scaling and replicating these techniques. Finally, we conclude with an evaluation of the future potential for such tools and future research opportunities.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

NASA NTRS1949

Performance of J33 turbojet engine with shaft-power extraction III : turbine performance

The performance of the turbine component of a J33 turbojet engine was determined over a range of turbine speeds from 8000 to 11,500 rpm.Turbine-inlet temperature was varied from the minimum required to drive the compressor to a maximum of approximately 2000 degrees R at each of several intermediate turbine speeds. Data are presented that show the horsepower developed by the turbine per pound of gas flow. The relation between turbine-inlet stagnation pressure, turbine-outlet stagnation pressure, and turbine-outlet static pressure was established. The turbine-weight-flow parameter varied from 39.2 to 43.6. The maximum turbine efficiency measured was 0.86 at a pressure ratio of 3.5 and a ratio of blade speed to theoretical nozzle velocity of 0.39. A generalized performance map of the turbine-horsepower parameter plotted against the turbine-speed parameter indicated that the best turbine efficiency is obtained when the turbine power is 10 percent greater than the compressor horsepower. The variation of efficiency with the ratio of blade speed to nozzle velocity indicated that the turbine operates at a speed above that for maximum efficiency when the engine is operated normally with the 19-inch-diameter jet nozzle.

Huppert, M C↗

NASA NTRS1998

Analysis of Thermal Radiation Effects on Temperatures in Turbine Engine Thermal Barrier Coatings

Thermal barrier coatings are important, and in some instances a necessity, for high temperature applications such as combustor liners, and turbine vanes and rotating blades for current and advanced turbine engines. Some of the insulating materials used for coatings, such as zirconia that currently has widespread use, are partially transparent to thermal radiation. A translucent coating permits energy to be transported internally by radiation, thereby increasing the total energy transfer and acting like an increase in thermal conductivity. This degrades the insulating ability of the coating. Because of the strong dependence of radiant emission on temperature, internal radiative transfer effects are increased as temperatures are raised. Hence evaluating the significance of internal radiation is of importance as temperatures are increased to obtain higher efficiencies in advanced engines.

Siegel, Robert↗

DOE OSTI2025

Investigating the Combustion Performance of Dual Fuel Combustion with Diesel and Port Injected Hydrogen in a Large Bore Locomotive Engine

The heavy-duty transportation sector has primarily relied on conventional diesel combustion engines given their reliability and high thermal efficiency relative to spark ignition engines, but increased focus on reducing greenhouse gas emissions has led to investigation into alternative fuels. Gaseous hydrogen fuel has garnered a great deal of recent interest in the engine community given it has zero carbon, but hydrogen is not available at the scale and cost that petroleum fuels are currently available, and this is a barrier to adoption for industries that are looking to decarbonize their operations. Because of the fuel flexibility provided, dual fuel technology offers a pathway for some industries to adopt hydrogen as a fuel source while maintaining sufficient flexibility in times and locations where the new fuel is not yet available. This computational study investigates dual fuel combustion in a large bore locomotive engine architecture using direct injected diesel and port injected gaseous hydrogen fuel. With an optimal port fuel injection configuration from previous work, simulations of varying substitution ratio, compression ratio, manifold air temperature, diesel injection timing, and diesel injection pressure were performed to understand their effect on combustion performance. Results indicated that both increased substitution ratio and higher intake air temperature accelerates hydrogen flame propagation and can result in high peak cylinder pressures. Additionally, diesel injection timing and injection pressure were demonstrated as effective methods for controlling dual fuel combustion heat release rates.

ODonnell, Patrick Christopher↗

NASA NTRSDate not supplied

Enhancement of an Electrified Tilt-Wing Propulsion System using Turbine Electrified Energy Management

Hybrid gas-electric aircraft propulsion architectures provide flexibility in the way that power and energy is managed when compared to their traditional pure-gas counterparts. In this paper, investigations are conducted for the impact this added flexibility has on the operability of turbomachinery. Specifically, the Turbine Electrified Energy Management (TEEM) concept is applied. It takes a controls approach to improving operability of the turbomachinery by utilizing electric hardware. In this paper, TEEM is applied to a propulsion system for a 15 passenger vertical lift concept vehicle. This is the first application of TEEM to a turbine engine that generates power. The study establishes TEEM as being applicable to this smaller thrust/power class of air transportation vehicle and explore show power can be otherwise managed in the propulsion system to benefit the aircraft. The simulation study demonstrates significant improvements in transient operability that expands the engine design space to enable a more efficient and lighter-weight engine design. Simulation results also demonstrate tighter regulation of the power turbine and rotor speeds, a slight decrease in bulk fuel burn, and an increase in the maximum thrust of ~7%. This is achieved through the power management control strategy and modestly sized electric machines with re-usable energy storage.

Turbine Electrified Energy Management↗

NASA NTRS1993

Test results from a simple, low-cost, pressure-fed liquid hydrogen/liquid oxygen rocket combustor

A simple, low-cost rocket engine was designed, fabricated, and successfully hot fire tested over a wide range of interface conditions and operating parameters. The engine used low enthalpy hydrogen (45 to 70 R, 200 to 390 psia) and oxygen (139 to 163 R, 210 to 480 psia) propellants pressure-fed directly from facility cryogenic tanks. The engine demonstrated excellent performance, with 97% average combustion efficiency, and absence of combustion instabilities. Engine design chamber pressure was 300 psia, yielding about 16,500 pounds thrust at sea level with a 3:1 expansion ration test nozzle. The engine used a fixed-element injector based on TRW's unique coaxial pintle design, but was operated at 60%, 80%, and 100% thrust levels by throttling facility propellant valves. The engine was tested at propellant mixture ratios (O/F) from 5.8 to 8.4; design O/F was 6.6. To document combustion stability, in five tests RDX explosive pulse guns were detonated in radial and tangential directions across the combustion chamber during steady-state operation. The largest disturbance consisted of simultaneous detonation of a 20-grain radial gun and a 40-grain tangential gun. In no case was an instability, either feed system mode or chamber acoustic mode, excited. High-frequency piezoelectric pressure transducers documented stable recovery from disturbance overpressures within 40 milliseconds of peak pressure. A total of 67 firing tests, accumulating 149 seconds of firing time above 10% P(sub c), were performed. Since parametric testing required run durations of only 2 to 3 seconds, a heat sink combustion chamber was employed for most runs. To evaluate the feasibility of a low-cost ablative system for a flight engine design, one 20-second continuous firing was conducted with a silicone rubber chamber/throat/nozzle liner cast in one piece directly into the engine. The ablative engine operated at the equivalent of 309 seconds sea level specific impulse, when adjusted to a 98% efficient 6:1 expansion ration nozzle, and 430 seconds vacuum specific impulse, when adjusted to a 98% efficient 50:1 expansion ratio nozzle. This engine and test series represent an initial subscale demonstration of a new booster-class engine that eliminates the cost and complexity associated with regenerative cooling and typical engine cycles. This paper presents a description of the engine design and discussion and summary data plots of the performance measured during the parametric testing.

Dressler, G. A.↗

DOE OSTI2021

An empirical investigation of organic software product lines

Abstract Software product line engineering is a best practice for managing reuse in families of software systems that is increasingly being applied to novel and emerging domains. In this work we investigate the use of software product line engineering in one of these new domains, synthetic biology. In synthetic biology living organisms are programmed to perform new functions or improve existing functions. These programs are designed and constructed using small building blocks made out of DNA. We conjecture that there are families of products that consist of common and variable DNA parts, and we can leverage product line engineering to help synthetic biologists build, evolve, and reuse DNA parts. In this paper we perform an investigation of domain engineering that leverages an open-source repository of more than 45,000 reusable DNA parts. We show the feasibility of these new types of product line models by identifying features and related artifacts in up to 93.5% of products, and that there is indeed both commonality and variability. We then construct feature models for four commonly engineered functions leading to product lines ranging from 10 to 7.5 × 10 20 products. In a case study we demonstrate how we can use the feature models to help guide new experimentation in aspects of application engineering. Finally, in an empirical study we demonstrate the effectiveness and efficiency of automated reverse engineering on both complete and incomplete sets of products. In the process of these studies, we highlight key challenges and uncovered limitations of existing SPL techniques and tools which provide a roadmap for making SPL engineering applicable to new and emerging domains.

97 MATHEMATICS AND COMPUTING↗

NASA NTRS1947

The Combination of Internal-Combustion Engine and Gas Turbine

While the gas turbine by itself has been applied in particular cases for power generation and is in a state of promising development in this field, it has already met with considerable success in two cases when used as an exhaust turbine in connection with a centrifugal compressor, namely, in the supercharging of combustion engines and in the Velox process, which is of particular application for furnaces. In the present paper the most important possibilities of combining a combustion engine with a gas turbine are considered. These "combination engines " are compared with the simple gas turbine on whose state of development a brief review will first be given. The critical evaluation of the possibilities of development and fields of application of the various combustion engine systems, wherever it is not clearly expressed in the publications referred to, represents the opinion of the author. The state of development of the internal-combustion engine is in its main features generally known. It is used predominantly at the present time for the propulsion of aircraft and road vehicles and, except for certain restrictions due to war conditions, has been used to an increasing extent in ships and rail cars and in some fields applied as stationary power generators. In the Diesel engine a most economical heat engine with a useful efficiency of about 40 percent exists and in the Otto aircraft engine a heat engine of greatest power per unit weight of about 0.5 kilogram per horsepower.

Zinner, K.↗

NASA NTRSDate not supplied

Flight Deck Design of a Hybrid Turbine/Electric Passenger Aircraft

NASA is exploring the development of a 180-passenger subsonic single engine aft turbine aircraft, The aft turbine provides electric power in a hybrid design to wing mounted electric engines, creating a highly efficient, high-bypass-ratio fan equivalent. The SUbsonic Single Aft eNgine (SUSAN) aircraft is being developed as a sustainable subsonic regional aircraft that seeks to reduce emission levels by 50% in the next few decades. Pilot-in-the-loop studies were conducted at the NASA Langley Research Center in Hampton, Virginia, to explore the flight deck design for the hybrid electric aircraft. Following modern trends in commercial aircraft flight decks with full time augmented controls and a quiet and dark philosophy, single throttle and simplified engine displays were developed for the SUSAN aircraft. The aircraft includes a single aft mounted turbine engine and 16 wing mounted electric fans. The final design was developed from feedback received during an earlier pilot-in-the-loop study where one, two, and three throttles were tested in standard airline operations, including various failures of the turbine and electric engines. Current flight deck designs normally provide control inceptors for each propulsion engine and an engine display for all primary aircraft engine parameters. With full time augmentation expected, a single throttle control with autothrottle always engaged, even during failures, is desired. Augmentation of flight controls using distributed thrust also requires full time control of the electric engines using automation. Additionally, electric engine thrust is augmented during climb based on battery state of charge. Thrust augmentation changes faster than human reaction time and therefore requires full-time automation. A pilot-in-the-loop study was conducted at the NASA Langley Research Center in Hampton, Virginia, to test the final design of the single throttle with simplified engine displays. Fourteen airline pilots evaluated the single throttle and engine display concept. Electric engine failures included one, four symmetric, and eight non-symmetric electric engine failures. The turbine engine was evaluated for complete and partial failure during critical phases of flight to include takeoff as well as enroute. Unexpected go-arounds increase workload and require significant throttle manipulation. Go-arounds were included to ensure the single throttle was usable for all phases of flight. Failures during takeoff required a return to the departure field and failures enroute required a diversion except for one and four electric engine failures as these failures did not affect aircraft flyability or range. There are currently no Part 25 aircraft certified with hybrid systems or electric engines with batteries as emergency propulsion. For turbine engine failures in the SUSAN aircraft design, range is limited to 30 minutes at full power. Battery state of charge and battery health displays were developed and tested for usability and to determine how well they supported pilot decisions for alternate airports during emergency diversions. Novel displays using shape and color were developed to provide immediate feedback when state of charge became critical. This paper details the pilot study including pilot feedback supporting the potential for increased automation and a single throttle control. Detailed recommendations are provided for a novel single throttle control and additional pilot controls to support selection of engines during start, shutdown, and engine troubleshooting procedures. This design deviates significantly from current practice of providing throttles for each propulsion engine. Engine display recommendations are provided based on pilot feedback during a guided post-evaluation interview. Battery state of charge and battery health display recommendations were collected from all airline crews. The simplified engine displays design was rated excellent as measured with a usability scale. Quantitative metrics include airspeed tracking, time to complete checklists, time to make diversion decisions and the quality of the diversion decision. Recommendations for future studies are documented with supporting research and current observations about upcoming flight deck certifications.

autothrottle↗

NASA NTRSDate not supplied

Flight Deck Design of a Hybrid Turbine/Electric Passenger Aircraft

NASA is exploring the development of a 180-passenger subsonic single engine aft turbine aircraft, The aft turbine provides electric power in a hybrid design to wing mounted electric engines, creating a highly efficient, high-bypass-ratio fan equivalent. The SUbsonic Single Aft eNgine (SUSAN) aircraft is being developed as a sustainable subsonic regional aircraft that seeks to reduce emission levels by 50% in the next few decades. Pilot-in-the-loop studies were conducted at the NASA Langley Research Center in Hampton, Virginia, to explore the flight deck design for the hybrid electric aircraft. Following modern trends in commercial aircraft flight decks with full time augmented controls and a quiet and dark philosophy, single throttle and simplified engine displays were developed for the SUSAN aircraft. The aircraft includes a single aft mounted turbine engine and 16 wing mounted electric fans. The final design was developed from feedback received during an earlier pilot-in-the-loop study where one, two, and three throttles were tested in standard airline operations, including various failures of the turbine and electric engines. Current flight deck designs normally provide control inceptors for each propulsion engine and an engine display for all primary aircraft engine parameters. With full time augmentation expected, a single throttle control with autothrottle always engaged, even during failures, is desired. Augmentation of flight controls using distributed thrust also requires full time control of the electric engines using automation. Additionally, electric engine thrust is augmented during climb based on battery state of charge. Thrust augmentation changes faster than human reaction time and therefore requires full-time automation. A pilot-in-the-loop study was conducted at the NASA Langley Research Center in Hampton, Virginia, to test the final design of the single throttle with simplified engine displays. Fourteen airline pilots evaluated the single throttle and engine display concept. Electric engine failures included one, four symmetric, and eight non-symmetric electric engine failures. The turbine engine was evaluated for complete and partial failure during critical phases of flight to include takeoff as well as enroute. Unexpected go-arounds increase workload and require significant throttle manipulation. Go-arounds were included to ensure the single throttle was usable for all phases of flight. Failures during takeoff required a return to the departure field and failures enroute required a diversion except for one and four electric engine failures as these failures did not affect aircraft flyability or range. There are currently no Part 25 aircraft certified with hybrid systems or electric engines with batteries as emergency propulsion. For turbine engine failures in the SUSAN aircraft design, range is limited to 30 minutes at full power. Battery state of charge and battery health displays were developed and tested for usability and to determine how well they supported pilot decisions for alternate airports during emergency diversions. Novel displays using shape and color were developed to provide immediate feedback when state of charge became critical. This paper details the pilot study including pilot feedback supporting the potential for increased automation and a single throttle control. Detailed recommendations are provided for a novel single throttle control and additional pilot controls to support selection of engines during start, shutdown, and engine troubleshooting procedures. This design deviates significantly from current practice of providing throttles for each propulsion engine. Engine display recommendations are provided based on pilot feedback during a guided post-evaluation interview. Battery state of charge and battery health display recommendations were collected from all airline crews. The simplified engine displays design was rated excellent as measured with a usability scale. Quantitative metrics include airspeed tracking, time to complete checklists, time to make diversion decisions and the quality of the diversion decision. Recommendations for future studies are documented with supporting research and current observations about upcoming flight deck certifications.

autothrottle↗

NASA NTRS1986

Amphibious Airplane

The airplane pictured is the new Air Shark I, a four-place amphibian that makes extensive use of composite materials and cruises at close to 200 miles per hour under power from a 200-horsepower engine. Air Shark I is a "homebuilt" airplane, assembled from a kit of parts and components furnished by Freedom Master Corporation, Satellite Beach, Florida. The airplane incorporates considerable NASA technology and its construction benefited from research assistance provided by Kennedy Space Center (KSC) In designing the Shark, company president Arthur M. Lueck was able to draw on NASA's aeronautical technology bank through KSC's computerized "recon" library. As a result of his work at KSC, the wing of the Air Shark I is a new airfoil developed by Langley Research Center for light aircraft. In addition, Lueck opted for NASA-developed "winglets," vertical extensions of the wing that reduce drag by smoothing air turbulence at the wingtips. The NASA technology bank also contributed to the hull design. Lueck is considering application of NASA laminar flow technology-means of smoothing the airflow over wing and fuselage-to later models for further improvement of the Shark's aerodynamic efficiency. A materials engineer, Lueck employed his own expertise in designing and selecting the materials for the composite segments, which include all structural members, exposed surfaces and many control components. The materials are fiber reinforced plastics, or FRP They offer a high strength-to-weight ratio, with a nominal strength rating about one and a half times that of structural steel. They provide other advantages: the materials can be easily molded into finished shapes without expensive tooling or machining, and they are highly corrosion resistant. The first homebuilt to be offered by Freedom Master, Air Shark I completed air and water testing in mid-1985 and the company launched production of kits.

Source record↗

DOE OSTI2022

A Double-Wiebe Function for Reactivity Controlled Compression Ignition Combustion Using Reformate Diesel

Abstract Reactivity controlled compression ignition (RCCI) combustion has previously been proposed as a method to achieve high fuel conversion efficiency and reduce engine emissions. A single-fuel RCCI combustion strategy can have decreased fuel system complexity by using a reformate fuel for port fuel injection and the parent fuel (diesel) for direct injection. This paper presents a one-dimensional computational model of a compression ignition engine with single-fuel RCCI. A Wiebe function is used to predict the combustion process by representing the mass fraction burned (MFB) on a crank angle resolved basis. One single-Wiebe function (SWF) and two double-Wiebe functions(DWFs) were fitted to experimentally derive MFB data using the least-square method. The fitted results were compared with MFBs calculated from experimental data to verify the accuracy. The SWF did not fully capture the MFB curve with high fidelity while the detailed DWF captured the MFB curve within a root mean square error of 1.4%. The reduced double-Wiebe function (RDWF) also resulted in a predicted combustion profile with similar accuracy. Hence, the RDWF was used in a GT-power thermodynamic study to understand the effects of the low-temperature heat release (LTHR) fraction and combustion phasing on combustion characteristics. At optimum phasing of 5–10 crank angle degree after the top dead center, increasing the LTHR fraction from 20% to 60% resulted in the fuel conversion efficiency increasing from 39.5% to 41.1%, thus suggesting that the reformate fuel-based RCCI strategy is viable to unlock improved combustion performance.

Energy & Fuels↗