Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Comprehensive two-dimensional gas chromatography under low-pressure conditions

The analysis of thermally labile and high-boiling point compounds by gas chromatography (GC) can be a challenge. One technique to overcome these challenges is low-pressure GC, which uses the vacuum produced from the mass spectrometer and wide-bore columns to elute compounds at significantly lower temperatures. While GC-MS is a powerful technique, comprehensive two-dimensional gas chromatography (GC × GC), allows for resolution of compounds that would typically coelute using GC. Here, in this study, a pesticide standard mixture (8270 MegaMix Standard) was analyzed using a conventional GC × GC-TOFMS configuration (0.25 mm inner diameter (i.d.) to a 0.18 mm i.d. column) and low-pressure GC × GC-TOFMS configuration (0.53 mm i.d. to a 0.53 mm i.d. column). Elution temperatures, sensitivity, and peak capacity were investigated for both configurations. Compounds eluted an average of 30 °C less on the low-pressure GC × GC-TOFMS configuration compared to the conventional GC × GC-TOFMS configuration. Moreover, the compounds were separated in ~13 min on the low-pressure GC × GC-TOFMS as opposed to 33 min for conventional GC × GC-TOFMS. However, due to the wide-bore columns and faster runtimes the low-pressure GC × GC-TOFMS had a lower, β corrected 2D peak capacity, n c,β,2D , of 1260 while the conventional GC × GC-TOFMS was 3588. Interestingly, both configurations yielded a similar peak capacity production of 93 peaks/min and 107 peaks/min for low-pressure and conventional GC × GC-TOFMS, respectively. A “real world” sample of diesel fuel was tested on the low-pressure and conventional GC × GC-TOFMS configurations and similar results were obtained compared to the pesticide standard mix except the peak capacity production of the low-pressure GC × GC-TOFMS configuration was higher than that of the conventional GC × GC-TOFMS method.

47 OTHER INSTRUMENTATION↗

Modeling radionuclide release of TRISO bearing fuel compacts during post-irradiation annealing tests

This article presents calculated radionuclide release fractions from TRISO fuel during post-irradiation annealing and comparison with AGR-1 irradiated TRISO compacts using the BISON fuel performance code. The BISON code was found to produce good agreement in an analytical comparison and with legacy German TRISO compact irradiation data. However, the recommended IAEA fission product diffusion coefficients did not produce good agreement with the 2014 AGR-1 data. Furthermore, the diffusion coefficients prefactors and activation energies were modified to obtain best agreement with the recent AGR data. Future work involves investigating the release behavior of silver from silicon carbide and implementing methods to provide predictive capability for the silver release behavior.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Lepidopteran mevalonate pathway optimization in Escherichia coli efficiently produces isoprenol analogs for next-generation biofuels

Terpenes constitute the largest class of natural products with over 55,000 compounds with versatile applications including drugs and biofuels. Introducing structural modifications to terpenes through metabolic engineering is an efficient and sustainable way to improve their properties. Here, in this study, we report the optimization of the lepidopteran mevalonate (LMVA) pathway towards the efficient production of isopentenyl pyrophosphate (IPP) analogs as terpene precursors. First, we linked the LMVA pathway to NudB, a promiscuous phosphatase, resulting in the production of the six-carbon analog of 3-methyl-3-buten-1-ol (isoprenol), 3-ethyl-3-buten-1-ol (C6-isoprenol). Using C6-isoprenol as the final product, we then engineered the LMVA pathway by redirecting its upstream portion from a thiolase-dependent pathway to a beta-oxidation pathway. The beta-oxidation LMVA pathway transforms valeric acid, a platform chemical that can be produced from biomass, into C6-isoprenol at a titer of 110.3 mg/L, improved from 5.5 mg/L by the thiolase LMVA pathway, which used propionic acid as a feedstock. Knockout of the E. coli endogenous thiolase genes further improved the C6-isoprenol titer to 390 mg/L, implying efficient production of homo isopentenyl pyrophosphate (HIPP). The beta-oxidation LMVA-NudB pathway also converts butanoic acid and hexanoic acid into isoprenol and isoprenol’s seven-carbon analog, 3-propyl-3-buten-1-ol (C7-isoprenol), respectively, suggesting the beta-oxidation LMVA pathway produces IPP and C7-IPP from the corresponding fatty acids. Fuel property tests revealed the longer chain isoprenol analogs have lower water solubilities, similar or higher energy densities, and comparable research octane number (RON) boosting effects to isopentenols. This work not only optimizes the LMVA pathway, setting the basis for homoterpene biosynthesis to expand terpene chemical space, but provides an efficient pathway to produce isoprenol analogs as next-generation biofuels from sustainable feedstocks.

59 BASIC BIOLOGICAL SCIENCES↗

Rational design of high-performance low-loading oxygen reduction catalysts for alkaline fuel cells

The lack of mechanistic understanding and catalyst design principles for alkaline electrolytes, especially for the sluggish oxygen reduction reaction, has impeded the advancement of alkaline fuel cells. Here, in this study, we propose a modified volcano plot and apply this rationale to strategically design Pt nanosheets with PdH x nanosheets substrates. This catalyst exhibited high stability with a specific activity of 1.71 mA cm −2 at 0.95 V versus the reversible hydrogen electrode, surpassing the benchmark of Pt/C by 49-fold. Spectroscopic, electrochemical and electron microscopic characterizations revealed that such performance enhancement originated from tensile-strained Pt{111} facets, improving oxidative stability and suppressing carbon corrosion. In fuel cell testing, the catalyst enabled a peak power density of 1.67 W cm −2 with a loading of 10 µg PGM Cathode cm −2 . Further optimization delivered a peak power density of 21.7 W mg −1 PGM Cathode+Anode with a total specific catalyst cost US$\$$1.27 kW −1 , surpassing the US Department of Energy’s Pt group metal loading and cost targets. This study provides valuable insights into catalyst design for the alkaline oxygen reduction reaction.

36 MATERIALS SCIENCE↗

Progress Toward Simulating Departure from Nucleate Boiling at High-Pressure Applications with Selected Wall Boiling Closures

Recently, a Eulerian-based two-fluid computational fluid dynamics (CFD) framework with a wall heat flux partitioning approach has been intensively investigated for departure from nucleate boiling (DNB) simulation under the U.S. Department of Energy–funded Consortium for Advanced Simulation of Light Water Reactors (CASL) program. Understanding of the DNB characteristics over a range of pressurized water reactor–like operating conditions and accurate prediction of boiling crisis in the nuclear power system have been grand challenges because of the large impact of DNB on reactor safety and operational economics. The ultimate goal of this task in the CASL program is to introduce a robust multiphase CFD–based DNB modeling framework that is capable of characterizing an entire boiling history in which the wall boiling mode experiences the following through multiple stages of heat transfer mode: (1) single-phase convective heat transfer, (2) nucleate boiling heat transfer, and (3) identification of the departure of nucleate boiling. To validate the CASL boiling model, we have benchmarked simulated DNB over three different flow channel configurations (pipe flow, 5 × 5 fuel bundle with mixing vane tests, and 5 × 5 fuel bundle without mixing vane tests) against experimental measurements, and the validation result with open literature is reported. The DNB detection criteria in the simulation are checked by monitoring the peak wall temperature, wall dryout factor, and net energy balance. In addition to the DNB performance test, some preliminary sensitivity results on closure model selection are reported to address the prediction capability of local void profile against measurements. The boiling simulation tested in this study exhibits a maximum deviation of 24% from the measured DNB value in a high-pressure (i.e., 138 bars) subcooled pipe flow test. The ranges of operating conditions are as follows: 1650 to 2650 kg/m 2 ·s for mass flux and 8.5 to 96 K for subcooled inlet temperature. The deviation is even reduced to 7% when the subcooled temperature is less than 40 K. Besides accuracy, base practice guidelines for DNB detection criteria are tested by monitoring three simulation variables: (1) maximum wall temperature, (2) wall dryout factor (i.e., K-value), and (3) energy balance. Numerical robustness of DNB simulation is largely achieved in most of the validation test except for a few high subcooled test cases.

42 ENGINEERING↗

Monitoring critical facilities by using advanced RF devices

The ability to monitor critical environment parameters of nuclear plants at all times, particularly during and after a disruptive accident, is vital for the safety of plant personnel, rescue and recovery crews, and the surrounding communities. Conventional hard-wired assets that depend on supplied power may be decimated as a result of such events, as witnessed in the Japanese Fukushima nuclear power plant in March 2011. Self-powered monitoring devices operating on a wireless platform, on the other hand, may survive such calamity and remain functional. The devices would be pre-positioned at strategic locations, particularly where the dangerous build-up of contamination and radiation may preclude subsequent manned entrance and surveillance. Equipped with sensors for β-γ radiation, neutrons, hydrogen gas, temperature, humidity, pressure, and water level, as well as with criticality alarms and imaging equipment for heat, video, and other capabilities, these devices can provide vital surveillance information for assessing the extent of plant damage, mandating responses (e.g., evacuation before impending hydrogen explosion), and enabling overall safe and efficient recovery in a disaster. A radio frequency identification (RFID)-based system - called ARG-US - may be modified and adapted for this task. Developed by Argonne for DOE, ARG-US (meaning 'watchful guardian') has been used successfully to monitor and track sensitive nuclear materials packages at DOE sites. It utilizes sensors in the tags to continuously monitor the state of health of the packaging and promptly disseminates alarms to authorized users when any of the preset sensor thresholds is violated. By adding plant-specific monitoring sensors to the already strong sensor suite and adopting modular hardware, firmware, and software subsystems that are tailored for specific subsystems of a plant, a Remote Area Modular Monitoring (RAMM) system, built on a wireless sensor network (WSN) platform, is being developed by Argonne National Laboratory. ARG-US RAMM, powered by on-board battery, can sustain extended autonomous surveillance operation during and following an incident. The benefits could be invaluable to such critical facilities as nuclear power plants, research and test reactors, fuel cycle manufacturing centers, spent-fuel dry-cask storage facilities, and other nuclear installations. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Design, Assembly, and Testing of the Neutron Imaging Lens for the National Ignition Facility

The National Ignition Facility will begin testing DT fuel capsules yielding greater than 10^13 neutrons during 2010. Neutron imaging is an important diagnostic for understanding capsule behavior. Neutrons are imaged at a scintillator after passing through a pinhole. The pixelated, 160-mm square scintillator is made up of ¼ mm diameter rods 50 mm long. Shielding and distance (28 m) are used to preserve the recording diagnostic hardware. Neutron imaging is light starved. We designed a large nine-element collecting lens to relay as much scintillator light as reasonable onto a 75 mm gated microchannel plate (MCP) intensifier. The image from the intensifier’s phosphor passes through a fiber taper onto a CCD camera for digital storage. Alignment of the pinhole and tilting of the scintillator is performed before the relay lens and MCP can be aligned. Careful tilting of the scintillator is done so that each neutron only passes through one rod (no crosstalk allowed). The 3.2 ns decay time scintillator emits light in the deep blue, requiring special glass materials. The glass within the lens housing weighs 26 lbs, with the largest element being 7.7 inches in diameter. The distance between the scintillator and the MCP is only 27 inches. The scintillator emits light with 0.56 NA and the lens collects light at 0.15 NA. Thus, the MCP collects only 7% of the available light. Baffling the stray light is a major concern in the design of the optics. Glass cost considerations, tolerancing, and alignment of this lens system will be discussed.

47 OTHER INSTRUMENTATION↗

Nanostructured Cathodes for Solid Oxide Fuel Cells by a Solution Spray-Coating Process

Composite nano-cathodes containing Sr-doped LaMnO 3 (LSM) and Gd 2 O 3 -doped CeO 2 (GDC) were deposited on yttria-stabilized zirconia (YSZ) discs and YSZ/NiO + YSZ bi-layer discs using an aqueous solution. The samples were heated over a range of temperatures from 700°C to 1200°C to form LSM + GDC porous films. The crystallite size was estimated using X-ray diffraction (XRD) Scherrer formula. The crystallite size was in the ~3 nm to ~80 nm range. Polarization resistance was measured by electrochemical impedance spectroscopy (EIS) from 400°C to 700°C. Nano-cathodes of ~70 nm thickness fired at 700°C exhibited polarization resistance of ~0.23 Ωcm 2 at 700°C. By contrast, LSM + YSZ cathodes made by a conventional process exhibited polarization resistance of ~2 Ωcm 2 . Fuel cell tests were conducted at 700°C on cells with nano-cathodes and conventional LSM + YSZ cathode. The maximum power density was ~0.51 Wcm –2 with nano-cathodes. By contrast, the corresponding power density with conventional LSM + YSZ cathodes was ~0.11 Wcm –2 . Here, the present work shows that very thin cathode functional layers can be deposited on sintered YSZ/NiO + YSZ bi-layer discs by using an aqueous solution. This approach in principle could be extended to large area cells.

36 MATERIALS SCIENCE↗

LANL Experience Rolling Zr-Clad LEU-10Mo Foils for AFIP-7

The cleaning, canning, rolling and final trimming of Low Enriched Uranium-10 wt. pct. Molybdenum (LEU-10Mo) foils for ATR (Advanced Test Reactor) fuel plates to be used in the AFIP-7 (ATR Full Size Plate In Center Flux Trap Position) experiments are summarized. Six Zr-clad foils were produced from two LEU-10Mo castings supplied to Los Alamos National Laboratory (LANL) by Y-12 National Security Complex. Details of cleaning and canning procedures are provided. Hot- and cold-rolling results are presented, including rolling schedules, images of foils in-process, metallography and local compositions of regions of interest, and details of final foil dimensions and process yield. This report was compiled from the slides for the presentation of the same name given by Duncan Hammon on May 12, 2011 at the AFIP-7 Lessons Learned meeting in Salt Lake City, UT, with Los Alamos National Laboratory document number LA-UR 11-02898.

Materials Science(36)↗

Advanced truck and bus radial materials for fuel efficiencies (Final Report)

PPG Industries, Inc. and Bridgestone Americas Tire Operations (BATO) propose to develop a novel surface-modified silica technology and demonstrate 4-6% improved fuel efficiency of Truck and Bus Radial (TBR) tires built from the technology. The proposed fuel efficiency increase will be achieved while maintaining or improving tear strength and tread wear. During rubber mixing, distributing silica in the rubber matrix is a challenge. This is because silica has a very polar surface, while rubbers have little polarity. It was hypothesized that surface treatments could cover part of the surface by hydrophobic groups, and reduce the surface polarity, thus helping to wet the silica with rubber during mixing and improving silica dispersion. During the project, the effect of different silica surface treatments on the surface energy of silica were determined, and related to the silica dispersion in rubber compounds. The results demonstrated that reducing the surface energy of silica samples improved dispersion in rubber compounds. Also, the preference for silica to migrate to the different phases in polymer blends was determined. The studies performed in binary polymer blends showed that carbon black has a preference to distribute in the different polymer phases in the order: SBR>BR~NR. Commercially available silica samples (treated and untreated) showed a preference in the order of SBR>NR>BR. Finally, the silica prototypes showed a preference in the order SBR=NR>BR. The knowledge gained regarding dispersion of treated silicas in rubber compounds was used to perform a series of studies to develop a silica – rubber compound combination with optimum performance for TBR treads. Initially, two silica prototypes (BXR-990 and BXR-991) were developed and used for a tire build at BATO’s tire plant in Warren County, TN. Results were evaluated and further silica and compound optimization was performed, prior to a final tire build. Manufacturing of the final silica prototype (BXR-1006) for the final tire build was performed at the PPG Silicas Pilot Plant in Monroeville, PA. Afterwards, experimental tires with silica-filled treads and control tires with carbon black-filled treads were built at BATO’s Warren County tire plant. The experimental TBR tires with silica-filled treads achieved the project goals for lab performance indicators, tread hardness and tear strength. The tires showed a 2.2% improvement in fuel efficiency compared to the control tires. While this improvement is lower than the 4% goal set initially, the improvement is significant and there are indicators that up to a 5% improvement in fuel efficiency could be achieved. This is supported by the confirmation of the validity of the fuel efficiency indicators made at the beginning of the project, and by the improvement in hysteresis and rolling resistance from tires built earlier in the project. The experimental tires produced using the BXR-990 silica prototype showed 47% improvement in tan δ at 60°C and 16% improvement in rolling resistance. Based on the results obtained, it is valid to estimate that the tires built with BXR-990 could provide around a 5% improvement in fuel efficiency, should we perform a fuel efficiency test. Tire wear for the experimental tires was 31% worse than for the control tires with the carbon black-filled tread compound. Other tools and further analysis of factors affecting wear are necessary to be evaluated to produce a silica tire with wear comparable to carbon black. Experimental and control tires were provided to the DOE for independent testing.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

SBIR Phase I Final Technical Report

The main purpose of this program, a Phase I SBIR effort, was to demonstrate the feasibility of constructing a fast void detector that can detect and localize voids with a quantifiable detection limit superior to a capacitive void sensor. The project used modeling and simulation of the radio- frequency (RF) sensor and environment, designed RF elements for the harsh environment, and fabricated the devices for temperature and pressure requirements. The project concluded with a demonstration of the system and feasibility of approach. First, the project performed theoretical work to simulate the system capabilities. Second, the project refined the RF sensor designs. Third, the effort fabricated devices. Fourth, the project demonstrated feasibility with a demonstration of the technology, individual components, and integrated elements. We assess that the project ended at Technology Readiness Level 3 (TRL-3) and demonstrated the feasibility of our concept.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Volume 10: Flow Test Facilities

Adding additional flow testing facilities has been considered as part of the High Flux Isotope Reactor (HFIR) Sustaining and Enhancing Neutron Science (SENSe) Initiative at Oak Ridge National Laboratory (ORNL) to support HFIR operations and experiments. This prospect has prompted many ideas and discussions regarding potential features, configurations, locations, and applications for the facilities. A working group of ORNL staff members was formed in fiscal year 2022 to recommend one or more configurations to best support future HFIR operations and scientific capacities and to develop order-of magnitude cost estimates and timing. The ideas discussed in this report include options ranging from upgrading existing small-scale testing facilities to building a full-scale HFIR mockup for detailed thermohydraulic testing and fuel assessment.

07 ISOTOPE AND RADIATION SOURCES↗

Radioisotope Power Systems: Considerations for use of Dynamic versus Static Conversion Technologies for NASA Missions

For more than five decades, Radioisotope Power Systems (RPS) have played a critical role in the exploration of space, enabling missions of scientific discovery to destinations across the solar system by providing electrical power to explore remote, challenging and extreme environments. In particular, RPS enable deep space missions where increased heliocentric distances reduce the ability of solar power to adequately meet spacecraft and instruments power requirements. Some previous notable missions that were enabled by RPS include Nimbus III, the Apollo Sur-face Experiments, the Pioneers 10 and 11, the Viking Mars Landers, Galileo, Ulysses, Cassini, New Horizons and Curiosity. The current operating set of missions that are enabled by RPS are Voyagers 1 and 2, Cassini, New Hori-zons, and Curiosity. The Multi-Mission Radioisotope Thermal Generator (MMRTG) is the current RPS used for mis-sions. An enhanced version of this generator outfitted with higher efficiency thermoelectrics is under development for potential use in the future. There are also current development efforts underway by NASA to explore dynamic power conversion systems such as Brayton and Stirling. This paper will compare and contrast the pros and cons of a generalized dynamic system with the current state-of-the-art thermoelectric static conversion system. The reason for this paper is to calmly analyze the pros and cons so that all the pertinent factors are placed under the same examination light with equal brightness. As with any purchase made the “newness” of certain items sometimes overrides a needed desire to fully vet all characteristics of the merchandise so that the best choice is made. The following areas will be specifically examined and discussed as they may impact the choice of radioisotope power system for a specific mission: • Projected power output to weight ratio (We/kg) • Amount of Pu-238 required per a fixed power output • Excess heat available to be rejected or used • Fueling operations during assembly by the Department of Energy (DOE) • Planetary protection protocol during fueling and testing of RPS • Transportation operations from DOE assembly site to Kennedy Space Center (KSC) • Remote operations at KSC prior to launch during Assembly Test and Launch Operations (ATLO) phase o Timing of the placement of the RPS onto spacecraft/rover o Off-normal operations at KSC

99 GENERAL AND MISCELLANEOUS↗

Higher_wood_density_lowers_feedstock_cost_and_has_minimal_impact_on_biomass_conversion_to_biofuels

Poplar and other woody feedstocks have the potential to provide up to 200 million tons of biomass per year that could be converted to liquid fuels. Most forestry strategies that aim at increasing biomass productivity per hectare rely on short rotation plantations of fast-growing varieties. The improvement of wood density as a key trait itself has largely been overlooked. We evaluated natural variation in wood density across a population of genetically diversePopulus trichocarpatrees grown in a common garden. Wood density varies greatly within this population but is heritable higher wood density was not systematically associated with reduced growth, challenging assumptions of a trade-off between wood density and biomass accumulation. Furthermore, denser wood led to significant improvements throughout the supply chain, including, lowering biomass production and transportation costs. Higher density not correlate to changes in biomass composition. Density did not impact bioconversion in the two feedstock-to-fuel pipelines tested (pretreatment by ionic liquids or soaking in aqueous ammonia, and fermentation to ethanol) on a representative subset of poplars. These findings highlight wood density as a promising breeding target for accelerating the development of high-yielding, conversion-efficient bioenergy crops and as an avenue for increasing land-use efficiency and reducing biomass transportation cost. This data set contain three datasets.

CBI↗