Search NASA⌕ Search

SEARCH · Search NASA

Results for “Inverse Multiplication”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Analysis of Exercise Loads to Inform Vibration Isolation System Design

BACKGROUND: This study was conducted with the primary interest of providing data that would inform Vibration Isolation and Stabilization (VIS) system design and performance for the European Enhanced Exploration Exercise Device (E4D). In preparation for the International Space Station (ISS) in-flight demonstration, a list of critical Human Health Countermeasures (HHC) exercises was compiled [1]. The goal of this study was to assess the ground reaction forces and moments imposed by an exercising subject in each of the six VIS Degrees of Freedom (DOFs) during a comprehensive set of these critical exercises performed on the E4D. METHODS AND RESULTS: The ISS in-flight demonstration list of critical exercises included seated aerobic rowing, bent-over rowing, cycling, front squats, back squats, conventional deadlifts, Romanian deadlifts, heel raises, overhead presses, reverse chops, and power clean presses. At the NASA Johnson Space Center (JSC) Prototype Immersive Technology (PIT) laboratory, motion capture data were collected on critical E4D exercises for six subjects. At the NASA JSC Active Response Gravity Offload System (ARGOS) facility, additional motion capture and load cell data were collected on offloaded trials for four subjects. Select data were extrapolated to represent a 5th percentile female subject and a 95th percentile male subject. A previous investigation comparing the forces obtained from the load cell and from motion capture based data found a satisfactory level of agreement between the two measurements [2]. The motion capture based data were analyzed for this study since it is driven by the subject’s trajectory alone, automatically excluding any forces exerted on the subject by the ARGOS offloading harness. The OpenSim [3, 4] biomechanical simulation inverse kinematics tool was used to calculate the joint angles based on the locations of motion capture markers placed at key positions on the subject’s body. An OpenSim plugin was then used to obtain the forces and moments generated by the subject during each trial, with the moments computed relative to the equilibrium location of the subject’s feet [5]. The force of gravity was also removed to simulate the loads generated by the exercise when performed in microgravity. The load plots for each trial were generated and visually analyzed to obtain the magnitudes of the peak loads for each exercise in each DOF. The typical period of exercise for each trial was also estimated and used to calculate the frequency for each trial. The exercise loads data was then organized in multiple ways to capture different aspects of the data. As a result of this study, we present a summary of the load magnitudes observed during these critical exercises utilizing the E4D.

C A Bell↗

Secure Mass Measurements From Transit Timing: 10 Kepler Exoplanets Between 3 and 8M⊕ with Diverse Densities and Incident Fluxes

We infer dynamical masses in eight multiplanet systems using transit times measured from Keplerʼs complete dataset, including short-cadence data where available. Of the 18 dynamical masses that we infer, 10 pass multiple tests for robustness. These are in systems Kepler-26 (KOI-250), Kepler-29 (KOI-738), Kepler-60 (KOI-2086), Kepler-105 (KOI-115), and Kepler-307 (KOI-1576). Kepler -105 c has a radius of 1.3R⊕ and a density consistent with an Earth-like composition. Strong transit timing variation (TTV) signals were detected from additional planets, but their inferred masses were sensitive to outliers or consistent solutions could not be found with independently measured transit times, including planets orbiting Kepler-49 (KOI-248), Kepler-57 (KOI-1270), Kepler-105 (KOI-115), and Kepler-177 (KOI-523). Nonetheless, strong upper limits on the mass of Kepler-177 cimply an extremely low density of 0.1 g cm−3. In most cases, individual orbital eccentricities were poorly constrained owing to degeneracies in TTV inversion. For five planet pairs in our sample, strong secular interactions imply a moderate to high likelihood of apsidal alignment over a wide range of possible eccentricities. We also find solutions for the three planets known to orbit Kepler-60 in a Laplace-like resonance chain. However, nonlibrating solutions also match the transit timing data. For six systems, we calculate more precise stellar parameters than previously known, enabling useful constraints on planetary densities where we have secure mass measurements. Placing these exoplanets on the mass–radius diagram, we find that a wide range of densities is observed among sub-Neptune-mass planets and that the range in observed densities is anticorrelated with incident flux.

Stars individual↗

Assessment of Off-Design Low-Boom Characteristics of a Low-Boom Supersonic Transport

Most design methods for a low-boom supersonic aircraft were developed for achieving an undertrack low-boom goal at the start of cruise. Attempts were made to design a supersonic aircraft achieving a low-boom goal for multiple azimuthal angles at the start of cruise. One unanswered question is how to define an achievable low-boom goal for multiple azimuthal angles at the start of cruise. This paper proposes a new analysis method to assess off-design low-boom characteristics of a low-boom supersonic transport designed for an undertrack low-boom goal at the start of cruise. This method opens a potentially feasible path for designing a supersonic aircraft that has the desired low-boom characteristics over the primary boom carpet for the entire cruise segment.

Low-boom supersonic transport↗

STOCHASTIC ACCELERATION AND THE EVOLUTION OF SPECTRAL DISTRIBUTIONS IN SYNCHRO-SELF-COMPTON SOURCES: A SELF-CONSISTENT MODELING OF BLAZARS' FLARES

The broadband spectral distributions of non-thermal sources, such as those of several known blazars, are well described by a log-parabolic fit. The second-degree term in these fits measures the curvature in the spectrum. In this paper, we investigate whether the curvature parameter observed in the spectra of the synchrotron emission can be used as a fingerprint of stochastic acceleration. As a first approach, we use the multiplicative central limit theorem to show how fluctuations in the energy gain result in the broadening of the spectral shape, introducing a curvature into the energy distribution. Then, by means of a Monte Carlo description, we investigate how the curvature produced in the electron distribution is linked to the diffusion in momentum space. To get a more generic description of the problem we turn to the diffusion equation in momentum space. We first study some 'standard' scenarios, in order to understand the conditions that make the curvature in the spectra significant, and the relevance of cooling during the acceleration process. We try to quantify the correlation between the curvature and the diffusive process in the pre-equilibrium stage, and investigate how the transition between the Klein-Nishina and the Thomson regimes, in inverse Compton cooling, determine the curvature in the distribution at equilibrium. We apply these results to some observed trends, such as the anticorrelation between the peak energy and the curvature term observed in the spectra of Mrk 421, and a sample of BL Lac objects whose synchrotron emission peaks at X-ray energies.

79 ASTRONOMY AND ASTROPHYSICS↗

Physical conditions in the reconnection layer in pulsar magnetospheres

The magnetosphere of a rotating pulsar naturally develops a current sheet (CS) beyond the light cylinder (LC). Magnetic reconnection in this CS inevitably dissipates a nontrivial fraction of the pulsar spin-down power within a few LC radii. We develop a basic physical picture of reconnection in this environment and discuss its implications for the observed pulsed gamma-ray emission. We argue that reconnection proceeds in the plasmoid-dominated regime, via a hierarchical chain of multiple secondary islands/flux ropes. The inter-plasmoid reconnection layers are subject to strong synchrotron cooling, leading to significant plasma compression. Using the conditions of pressure balance across these current layers, the balance between the heating by magnetic energy dissipation and synchrotron cooling, and Ampere's law, we obtain simple estimates for key parameters of the layers—temperature, density, and layer thickness. In the comoving frame of the relativistic pulsar wind just outside of the equatorial CS, these basic parameters are uniquely determined by the strength of the reconnecting upstream magnetic field. For the case of the Crab pulsar, we find them to be of order 10 GeV, 10{sup 13} cm{sup –3}, and 10 cm, respectively. After accounting for the bulk Doppler boosting due to the pulsar wind, the synchrotron and inverse-Compton emission from the reconnecting CS can explain the observed pulsed high-energy (GeV) and very high energy (∼100 GeV) radiation, respectively. Also, we suggest that the rapid relative motions of the secondary plasmoids in the hierarchical chain may contribute to the production of the pulsar radio emission.

79 ASTRONOMY AND ASTROPHYSICS↗

Predictability and empirical dynamics of fisheries time series in the North Pacific

Previous studies have documented a strong relationship between marine ecosystems and large-scale modes of sea surface height (SSH) and sea surface temperature (SST) variability in the North Pacific such as the Pacific Decadal Oscillation and the North Pacific Gyre Oscillation. In the central and western North Pacific along the Kuroshio-Oyashio Extension (KOE), the expression of these modes in SSH and SST is linked to the propagation of long oceanic Rossby waves, which extend the predictability of the climate system to ~3 years. Using a multivariate physical-biological linear inverse model (LIM) we explore the extent to which this physical predictability leads to multi-year prediction of dominant fishery indicators inferred from three datasets (i.e., estimated biomasses, landings, and catches). We find that despite the strong autocorrelation in the fish indicators, the LIM adds dynamical forecast skill beyond persistence up to 5-6 years. By performing a sensitivity analysis of the LIM forecast model, we find that two main factors are essential for extending the dynamical predictability of the fishery indicators beyond persistence. The first is the interaction of the fishery indicators with the SST/SSH of the North and tropical Pacific. The second is the empirical relationship among the fisheries time series. This latter component reflects stock-stock interactions as well as common technological and human socioeconomic factors that may influence multiple fisheries and are captured in the training of the LIM. These results suggest that empirical dynamical models and machine learning algorithms, such as the LIM, provide an alternative and promising approach for forecasting key ecological indicators beyond the skill of persistence.

60 APPLIED LIFE SCIENCES↗

The impact of alternative trait-scaling hypotheses for the maximum photosynthetic carboxylation rate (V cmax ) on global gross primary production [The impact of alternative V cmax trait-scaling hypotheses on global gross primary production]

Here, the maximum photosynthetic carboxylation rate (V cmax ) is an influential plant trait that has multiple scaling hypotheses, which is a source of uncertainty in predictive understanding of global gross primary production (GPP). Four trait-scaling hypotheses (plant functional type, nutrient limitation, environmental filtering, and plant plasticity) with nine specific implementations were used to predict global V cmax distributions and their impact on global GPP in the Sheffield Dynamic Global Vegetation Model (SDGVM). Global GPP varied from 108.1 to 128.2 PgC yr –1 , 65% of the range of a recent model intercomparison of global GPP. The variation in GPP propagated through to a 27% coefficient of variation in net biome productivity (NBP). All hypotheses produced global GPP that was highly correlated ( r = 0.85–0.91) with three proxies of global GPP. Plant functional type-based nutrient limitation, underpinned by a core SDGVM hypothesis that plant nitrogen (N) status is inversely related to increasing costs of N acquisition with increasing soil carbon, adequately reproduced global GPP distributions. Further improvement could be achieved with accurate representation of water sensitivity and agriculture in SDGVM. Mismatch between environmental filtering (the most data-driven hypothesis) and GPP suggested that greater effort is needed understand V cmax variation in the field, particularly in northern latitudes.

60 APPLIED LIFE SCIENCES↗

Seismic Event Characterization Using Full Moment Tensors on the Hypersphere

Moment tensor solutions provide insights into the deformation that has occurred in the source region of a seismic event and are therefore of great value in identifying different types of seismic sources, such as when monitoring for underground nuclear tests. Despite this utility, inversion of waveforms recorded by seismometers for their full seismic moment tensor is not yet routine, and development of robust methods to classify events based on this information is in its infancy. Here, we assemble an inventory of 1405 full moment tensor solutions that include explosive, earthquake, and collapse events, and investigate the use of anisotropic probability distribution functions on the 5D hypersphere to discriminate between these sources. Using a Bayesian classifier, we obtain optimal success rates of 98.4% across all events and demonstrate that modification of the prior probabilities provides a natural way to alter the balance between not missing desirable events (such as explosions) versus misclassifying large numbers of undesired events (such as earthquakes). The approach is specifically designed to progress from traditional, bipolar event screening metrics to more generalized event identification across multiple types of seismic sources. Despite current databases containing insufficient numbers of events to definitively demonstrate at present, we also find intriguing evidence of subgroupings within individual source populations on the hypersphere, for example, between chemical and nuclear explosions, raising the potential possibility of discriminating between these event types in the future.

Geosciences↗

The radiative effect of aerosols in the earth's atmosphere

A modified two-flux approximation is employed to compute the transfer of radiation in a finite, inhomogeneous, turbid atmosphere. A perturbation technique is developed to allow the treatment of nongray gaseous absorption with multiple scattering. The perturbation method, which employs a backscatter factor as a parameter, can be used with anisotropic particle scattering as well as Rayleigh scattering. This method is used to study the effect of aerosols on radiative solar heating and infrared cooling as well as the radiative-convective temperature distribution in the earth's atmosphere. It is found that the effect of aerosols in the infrared cannot be neglected; while in the visible, the effect can be of the same order as that due to absorption by water vapor. For a high surface albedo (greater than 0.30) heating of the earth-atmosphere system results due to the presence of aerosols. The aerosols also reduce the amount of convection needed to maintain a stable atmosphere. For the case of a dense haze a temperature inversion is found to exist close to the ground.

Wang, W.-C.↗

A smeared crack modeling framework accommodating multi-directional fracture at finite strains

A generic smeared crack modeling framework predicated on the deformation gradient decomposition (DGD) approach is proposed for use in dynamic fracture problems at finite strains, accommodating failure along multiple mutually orthogonal fracture planes embedded within an independently defined bulk material model. Within this constitutive framework, the traction equilibrium conditions imposed at each failure surface are used to determine the associated crack displacements stored as internal state variables. In general, the enforcement of interfacial equilibrium entails the implicit solution of a non-linear system of equations within the constitutive update procedure. However, if inertial effects arising due to the relative motion of the fractured material are incorporated within the model, the traction equilibrium conditions are shown to give rise to corresponding dynamic equations of motion governing the time-evolution of the crack opening displacements. For dynamic problems, an explicit time-integration procedure is devised to efficiently update the material state, subject to a set of internal frictionless contact constraints to prevent material inversion. Finally, the efficacy of the proposed modeling framework is investigated through several benchmark dynamic fracture problems run within the explicit finite element code DYNA3D.

42 ENGINEERING↗

Secure Mass Measurements From Transit Timing: 10 Kepler Exoplanets Between 3 and 8 M⊕ With Diverse Densities and Incident Fluxes

We infer dynamical masses in eight multiplanet systems using transit times measured from Keplerʼs complete data set, including short-cadence data where available. Of the 18 dynamical masses that we infer, 10 pass multiple tests for robustness. These are in systems Kepler-26 (KOI-250), Kepler-29 (KOI-738), Kepler-60 (KOI-2086), Kepler-105 (KOI-115), and Kepler-307 (KOI-1576). Kepler-105 c has a radius of 1.3 R(sub ⨁) and a density consistent with an Earth-like composition. Strong transit timing variation (TTV) signals were detected from additional planets, but their inferred masses were sensitive to outliers or consistent solutions could not be found with independently measured transit times, including planets orbiting Kepler-49 (KOI-248), Kepler-57 (KOI-1270), Kepler-105 (KOI-115), and Kepler-177 (KOI-523). Nonetheless, strong upper limits on the mass of Kepler-177 c imply an extremely low density of ∽0.1 g cm(exp −3). In most cases, individual orbital eccentricities were poorly constrained owing to degeneracies in TTV inversion. For five planet pairs in our sample, strong secular interactions imply a moderate to high likelihood of apsidal alignment over a wide range of possible eccentricities. We also find solutions for the three planets known to orbit Kepler-60 in a Laplace-like resonance chain. However, nonlibrating solutions also match the transit timing data. For six systems, we calculate more precise stellar parameters than previously known, enabling useful constraints on planetary densities where we have secure mass measurements. Placing these exoplanets on the mass–radius diagram, we find that a wide range of densities is observed among sub-Neptune-mass planets and that the range in observed densities is anticorrelated with incident flux.

Individual stars↗

Multi-Fidelity Active Subspaces for Wind Farm Uncertainty Quantification

Wind plants operate in stochastic environments characterized by complex turbulent flow dynamics and high-dimensional random variables. A key step in uncertainty quantification studies is sensitivity analysis and dimension reduction that can facilitate the development of surrogate models to be used for forward and inverse propagation or optimization under uncertainty. Prior work has shown active subspaces are an effective tool for identifying important directions in the space of stochastic inputs; however, they have only been applied to single-fidelity wind plant models. In this study, we investigate the efficacy of a multi-fidelity active subspace method for analyzing the uncertainty in wind plant power output. The multi-fidelity active subspace estimator offers the promise of increased accuracy in identifying active subspaces as compared to a single-fidelity estimator for the same computational cost, or a reduction in cost for the same accuracy. This makes the study of uncertainty in larger wind plants and with higher fidelity physics tractable. The multi-fidelity active subspace method is applied to gridded and existing wind plant layouts with single and multiple inflow conditions and its performance for surrogate modeling and uncertainty propagation is compared against a single-fidelity active subspace method. This multi-fidelity approach yields substantial computational speedups of 2x - 3.4x across the test cases along with acceptable accuracy in surrogate modeling and computing statistical moments.

active subspace↗

The Dynamic Tumor Bed: Volumetric Changes in the Lumpectomy Cavity During Breast-Conserving Therapy

Purpose: To characterize the magnitude of volume change in the postoperative tumor bed before and during radiotherapy, and to identify any factors associated with large volumetric change. Methods and Materials: Thirty-six consecutive patients with early-stage or preinvasive breast cancer underwent breast-conserving therapy at our institution between June 2006 and October 2007. Computed tomography (CT) scans of the breast were obtained shortly after surgery, before the start of radiotherapy (RT) for treatment planning, and, if applicable, before the tumor bed boost. Postoperative changes, seroma, and surgical clips were used to define the tumor bed through consensus agreement of 3 observers (B.P., D.I., and J.L.). Multiple variables were examined for correlation with volumetric change. Results: Between the first and last scan obtained (median time, 7.2 weeks), the tumor bed volume decreased at least 20% in 86% of patients (n = 31) and at least 50% in 64% of patients (n = 23). From the postoperative scan to the planning scan (median time, 3 weeks), the tumor bed volume decreased by an average of 49.9%, or approximately 2.1% per postoperative day. From planning scan to boost scan (median interval, 7 weeks), the median tumor bed volume decreased by 44.6%, at an average rate of 0.95% per postoperative day. No single factor was significantly associated with a change in tumor bed volume greater than 20%. Conclusions: The average postlumpectomy cavity undergoes dramatic volumetric change after surgery and continues this change during RT. The rate of change is inversely proportional to the duration from surgery. In this study no factors studied predicted large volumetric change.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

X-Raying the Coronae of HD 155555

We present an analysis of the high-resolution Chandra observation of the multiple system, HD 155555 (an RS CVn type binary system, HD 155555 AB, and its spatially resolved low-mass companion HD 155555 C). This is an intriguing system which shows properties of both an active pre-main sequence star and a synchronised (main sequence) binary. We obtain the emission measure distribution, temperature structures, plasma densities, and abundances of this system and compare them with the coronal properties of other young/active stars. HD 155555 AB and HD 155555 C produce copious X-ray emission with log L(sub x) of 30.54 and 29.30, respectively, in the 0.3-6.0 kiloelectronvolt energy band. The light curves of individual stars show variability on timescales of few minutes to hours. We analyse the dispersed spectra and reconstruct the emission measure distribution using spectral line analysis. The resulting elemental abundances exhibit inverse first ionisation potential effect in both cases. An analysis of He-like triplets yields a range of coronal electron densities 1010 − 1013 per cubic centimeter. Since HD 155555 AB is classified both as an RS CVn and a PMS star, we compare our results with those of other slightly older active main-sequence stars and T Tauri stars, which indicates that the coronal properties of HD 155555 AB closely resemble that of an older RS CVn binary rather than a younger PMS star. Our results also suggests that the properties of HD 155555 C is very similar to those of other active M dwarfs.

stars: coronae↗

The role of pressure in inverse design for assembly

Isotropic pairwise interactions that promote the self-assembly of complex particle morphologies have been discovered by inverse design strategies derived from the molecular coarse-graining literature. While such approaches provide an avenue to reproduce structural correlations, thermodynamic quantities such as the pressure have typically not been considered in self-assembly applications. In this work, we demonstrate that relative entropy optimization can be used to discover potentials that self-assemble into targeted cluster morphologies with a prescribed pressure when the iterative simulations are performed in the isothermal-isobaric ensemble. The benefits of this approach are twofold. First, the structure and the thermodynamics associated with the optimized interaction can be controlled simultaneously. Second, by varying the pressure in the optimization, a family of interparticle potentials that all self-assemble the same structure can be systematically discovered, allowing for a deeper understanding of self-assembly of a given target structure and providing multiple assembly routes for its realization. Selecting an appropriate simulation ensemble to control the thermodynamic properties of interest is a general design strategy that could also be used to discover interaction potentials that self-assemble structures having, for example, a specified chemical potential.

74 ATOMIC AND MOLECULAR PHYSICS↗

The Goddard Snow Radiance Assimilation Project: An Integrated Snow Radiance and Snow Physics Modeling Framework for Snow/cold Land Surface Modeling

Microwave-based retrievals of snow parameters from satellite observations have a long heritage and have so far been generated primarily by regression-based empirical "inversion" methods based on snapshots in time. Direct assimilation of microwave radiance into physical land surface models can be used to avoid errors associated with such retrieval/inversion methods, instead utilizing more straightforward forward models and temporal information. This approach has been used for years for atmospheric parameters by the operational weather forecasting community with great success. Recent developments in forward radiative transfer modeling, physical land surface modeling, and land data assimilation are converging to allow the assembly of an integrated framework for snow/cold lands modeling and radiance assimilation. The objective of the Goddard snow radiance assimilation project is to develop such a framework and explore its capabilities. The key elements of this framework include: a forward radiative transfer model (FRTM) for snow, a snowpack physical model, a land surface water/energy cycle model, and a data assimilation scheme. In fact, multiple models are available for each element enabling optimization to match the needs of a particular study. Together these form a modular and flexible framework for self-consistent, physically-based remote sensing and water/energy cycle studies. In this paper we will describe the elements and the integration plan. All modules will operate within the framework of the Land Information System (LIS), a land surface modeling framework with data assimilation capabilities running on a parallel-node computing cluster. Capabilities for assimilation of snow retrieval products are already under development for LIS. We will describe plans to add radiance-based assimilation capabilities. Plans for validation activities using field measurements will also be discussed.

Kim, E.↗

On the VHF Source Retrieval Errors Associated with Lightning Mapping Arrays (LMAs)

This presentation examines in detail the standard retrieval method: that of retrieving the (x, y, z, t) parameters of a lightning VHF point source from multiple ground-based Lightning Mapping Array (LMA) time-of-arrival (TOA) observations. The solution is found by minimizing a chi-squared function via the Levenberg-Marquardt algorithm. The associated forward problem is examined to illustrate the importance of signal-to-noise ratio (SNR). Monte Carlo simulated retrievals are used to assess the benefits of changing various LMA network properties. A generalized retrieval method is also introduced that, in addition to TOA data, uses LMA electric field amplitude measurements to retrieve a transient VHF dipole moment source.

inversion↗

Rational Design and Reticulation of Infinite qbe Rod Secondary Building Units into Metal–Organic Frameworks through a Global Desymmetrization Approach for Inverse C 3 H 8 /C 3 H 6 Separation

Abstract The development of reticular chemistry has enabled the construction of a large array of metal–organic frameworks (MOFs) with diverse net topologies and functions. However, dominating this class of materials are those built from discrete/finite secondary building units (SBUs), yet the designed synthesis of frameworks involving infinite rod‐shaped SBUs remain underdeveloped. Here, by virtue of a global linker desymmetrization approach, we successfully targeted a novel Cu‐MOF (Cu‐ASY) incorporating infinite Cu‐carboxylate rod SBUs with its structure determined by micro electron diffraction (MicroED) crystallography. Interestingly, the rod SBU can be simplified as a unique cylindric sphere packingqbetubule made of [4 3 .6 2 ] tiles, which further connect the tritopic linkers to give a newly discovered 3,5‐connectedgfcnet. Cu‐ASY is a permanent ultramicroporous material featuring 1D channels with highly inert surfaces and shows a preferential adsorption of propane (C 3 H 8 ) over propene (C 3 H 6 ). The efficiency of C 3 H 8 selective Cu‐ASY is validated by multicycle breakthrough experiments, giving C 3 H 6 productivity of 2.2 L/kg. Density functional theory (DFT) calculations reveal that C 3 H 8 molecules form multiple C−H⋅⋅⋅π and atypical C−H⋅⋅⋅ H−C van der Waals interactions with the inner nonpolar surfaces. This work therefore highlights the linker desymmetrization as an encouraging and intriguing strategy for achieving unique MOF structures and properties.

Chemistry↗