Properties of Inconel 625 mesh structures grown by electron beam additive manufacturing
Not Available
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Not Available
The phase properties and deformation behavior of the δ–ferrite and γ–austenite phases of CF–3 and CF–8 cast duplex stainless steels were characterized by nanoindentation and microstructure-based finite element method (FEM) models. We evaluated the elastic modulus of each phase and the results indicate that the mean elastic modulus of the δ–ferrite phase is greater than that of the γ–austenite phase, and the mean nanoindentation hardness values of each phase are approximately the same. Furthermore, the elastic FEM model results illustrate that greater von Mises stresses are located within the δ–ferrite phase, while greater von Mises strains are located in the γ–austenite phase in response to elastic deformation. The elastic moduli calculated by FEM agree closely with those measured by tensile testing. Finally, the plastically deformed specimens exhibit an increase in misorientation, deformed grains, and subgrain structure formation as measured by electron backscatter diffraction (EBSD).
Nanostructured ferritic alloys (NFAs) are a promising structural material for advanced nuclear systems due to their exceptional radiation tolerance and high-temperature mechanical properties. Their remarkable properties result from the ultrafine ultrahigh density Y-Ti-O nanoclusters dispersed within the ferritic matrix. In this work, we performed in-situ synchrotron X-ray diffraction tests to study the tensile deformation process of the three types of NFAs: 9YWTV, 14YWT-sm13, and 14YWT-sm170 at both room temperature and elevated temperatures. A technique was developed, combining Kroner’s model and X-ray measurement, to determine the intrinsic monocrystal elastic-stiffness constants, and polycrystal Young’s modulus and Poisson’s ratio of the NFAs. Temperature dependence of elastic anisotropy was observed in the NFAs. An analysis of intergranular strain and strengthening factors determined that 14YWT-sm13 had a higher resistance to temperature softening compared to 9YWTV, attributed to the more effective nanoparticle strengthening during high-temperature mechanical loading.
Ternary single-phase concentrated solid solution alloys (SP-CSAs), so-called "medium entropy alloys", not only possess notable mechanical and physical properties but also form a model system linking the relatively simple binary alloys to the complex high entropy alloys. Our knowledge of their intrinsic properties is vital to understand the material behavior and to prompt future applications. To this end, three model alloys NiCoFe, NiCoCr, and NiFe-20Cr have been selected and grown as single crystals. We measured their elastic constants using an ultrasonic method, and several key materials properties, such as shear modulus, bulk modulus, elastic anisotropy, and Debye temperatures have been derived. Furthermore, nanoindentation tests have been performed on these three alloys together with Ni, NiCo and NiFe on their (100) surface, to investigate the strengthening mechanisms. NiCoCr has the highest hardness, NiFe, NiCoFe and NiFe-20Cr share a similar hardness that is apparently lower than NiCoCr; NiCo has the lowest hardness in the alloys, which is similar to elemental Ni. The Labusch-type solid solution model has been applied to interpret the nanoindentation data, with two approaches used to calculate the lattice mismatch. Finally, by adopting an interatomic spacing matrix method, the Labusch model can reasonably predict the hardening effects for the whole set of materials.
Although indentation experiments have long been used to measure the hardness and Young's modulus, the utility of this technique in analyzing the complete elastic–plastic response of materials under contact loading has only been realized in the past few years – mostly due to recent advances in testing equipment and analysis protocols. This paper provides a timely review of the recent progress made in this respect in extracting meaningful indentation stress–strain curves from the raw datasets measured in instrumented spherical nanoindentation experiments. These indentation stress–strain curves have produced highly reliable estimates of the indentation modulus and the indentation yield strength in the sample, as well as certain aspects of their post-yield behavior, and have been critically validated through numerical simulations using finite element models as well as direct in situ scanning electron microscopy (SEM) measurements on micro-pillars. Much of this recent progress was made possible through the introduction of a new measure of indentation strain and the development of new protocols to locate the effective zero-point of initial contact between the indenter and the sample in the measured datasets. As a result, this has led to an important key advance in this field where it is now possible to reliably identify and analyze the initial loading segment in the indentation experiments.
This study systematically investigates the effects of three rejuvenation modes, namely biaxial loading, thermal pressure loading, and cryogenic thermal cycling, on the microstructures and mechanical properties of Cu 64 Zr 36 metallic glasses (MGs) using molecular dynamics (MD) simulations. The simulation results demonstrate that biaxial tension application during loading results in a rejuvenated glassy state with high strength. Specifically, we find that the yield stress, Young's modulus, and shear modulus of the rejuvenated glass obtained by biaxial tensile loading decreased by 2.8%, 2.1%, and 2.7%, respectively, compared to an as-cast MG reference. We also find that MGs achieve the greatest degree of rejuvenation, at the expense of strength, with the use of thermal pressure loading. Interestingly, the application of cryogenic thermal cycling results in a rejuvenated state with a lower strength drop compared to thermal pressure loading. Furthermore, analysis of the potential energy and medium-range-order (MRO) size indicates that the microstructures of MGs achieves a high-energy ordered glass state after thermal pressure loading, but a high-energy disordered glass state after biaxial tensile loading and cryogenic thermal cycling. Furthermore, these findings provide meaningful insights into the effect of rejuvenation modes on the microstructures and mechanical properties of MGs, as well as useful guidelines for designing MGs with high strength and superior plasticity for prospective applications in industry.
This study utilized additively reinforced thermoforming (ART) to enhance the thermomechanical properties of polyethylene terephthalate glycol (PETG) sheet. ART materials were produced by overprinting PETG/carbon fiber filament (PETG/CF) on neat PETG sheets at varying conditions. The mechanical properties of the PETG sheet, PETG/CF, and ART materials were assessed, showing that ART exhibited superior tensile strength and modulus of elasticity. The tensile strength and modulus in the x-direction for ART at 265°C were 57.32 ± 2.9 MPa and 3.41 ± 0.4 GPa, respectively, compared to 49.1 ± 0.5 MPa and 1.92 ± 0.09 GPa for neat PETG. Microstructural analysis revealed strong interfacial adhesion between layers, while thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and heat deflection temperature analysis provided insights into the ART material's thermoforming behavior, aiding design optimization for enhanced stiffness, reduced necking, and improved customization. In conclusion, this information can be used to design for the thermoforming operation.
Modern automotive applications demand lightweight, multifunctional materials to reach mileage goals and natural fiber reinforced composites (NFRCs) are one of the classes of materials proposed as a solution. NFRCs exhibit good vibration damping properties and have low density, but are often limited by processing challenges, poor-fiber matrix compatibility and variable performance. Herein, we investigate non-woven wet-lay of comingled banana fiber (BF), recycled glass fiber (rGF), and polypropylene (PP) fibers to in situ sizing and preparation of composite feedstocks for compression molding. BF and rGF hybrids were prepared by stacking rGF layers during compression molding to produce composites with various fiber ratios. The effect of fiber content, in-situ sizing and ratio of BF to rGF on tensile, flexural and vibration damping performance are investigated. Key results are the significant increase in tensile strength by in situ sizing (40 % sized at 60 wt% BF) and in flexural modulus (+58 % sized at 60 wt% BF) and flexural strength (+41 % sized 60 wt% BF) compared to the unsized equivalent. For BF-rGF hybrid composites with40 wt% total fiber content, flexural strength and modulus were improved by 51 % and 231 % respectively for a 1:1 ratio BF:rGF compared to BF reinforced system. Lastly, identifying the cross-over point where damping and stiffness are optimized for a hybrid composite. These findings demonstrate that these composites can be used as alternative to synthetic fiber or mineral filled composites in automotive applications, particularly where weight reduction, vibration damping and stiffness are desired.
In this work, the elastic characteristics of additively manufactured Ti-5553 octet truss lattice cubes were examined using resonant ultrasound spectroscopy (RUS) techniques and correlated to X-ray computed tomography measurements of strut continuity. RUS models and measurements identified an outlier lattice possessing lower effective modulus despite larger effective density. Here, experimental measurements of density and effective Young's modulus were treated as input parameters in a homogenous anisotropic continuum model. The continuum model exhibited good agreement with experimental RUS measurements, thus confirming the potential for a simplified approximation of the octet truss lattice.
Fusion dynamics and the onset of quasi-fission in reactions, leading to production of superheavy nuclei are investigated using the constrained molecular dynamics model. Constraints on the parameters of the nuclear equation of state are derived from experimental fusion probabilities. Here, the obtained constraint on the modulus of incompressibility of nuclear matter K 0 = 240 –260 MeV is consistent with the results of previous study using the Boltzmann-Uehling-Uhlenbeck equation and also with constraints derived using the recent neutron star binary collision event GW170817. Unlike the modulus of incompressibility of symmetric nuclear matter, the stiffness of the density-dependence of symmetry energy influences the fusion probability only weakly.
We introduce pulse-echo ultrasound as a method for characterizing the impact of powder bed fusion parameters on the properties of additively manufactured stainless-steel components, their material anisotropy, and location-dependent heterogeneity. Our results indicate that accurate characterization requires careful selection of ultrasonic propagation paths, which must consider the direction of additive layering, variations in processing parameters, and the component's geometry. We employed two distinct methods to estimate material properties from ultrasonic data: One assumes isotropy, while the other accounts for anisotropic interactions during the propagation of elastic waves. When applied to samples fabricated with laser energy densities ranging from 24 to 42 J/mm³ , these methods revealed transverse isotropy and weak anisotropy (quantified by small Thomsen parameters, ε = 0.0651 and γ = 0.0092) and less than a ∼6 % change in acoustic impedance. The assumption of isotropy, in this case, leads to small errors (less than 4 % or 1 % for Young's modulus in the build or transverse directions) when estimating orthotropic material properties using ultrasonic data measured along just two orthogonal directions, one of which must align with the build direction. By comparing ultrasonic measurements — which aggregate the spatial variability in material properties along the length of elastic wave propagation into a single value — with localized measurements obtained from surface nanoindentation, we uncovered and spatially profiled significant differences between the surface and interior properties. Specifically, the surface Young's modulus decreased from approximately 210 GPa to 180 GPa within a depth of about 3 mm. We attribute this surface-localized heterogeneity in PBF-fabricated components to distinct thermal histories experienced by the surface and interior regions. Collectively, the results of this study establish a framework for the ultrasonic characterization of material heterogeneity and anisotropy in material properties and demonstrate its application in additively manufactured metal components.
The emergence of novel extrusion-based additive manufacturing (AM) processes has prompted the development of new thermoplastic composite feedstocks, and broadening sustainability initiatives have driven the development of bio-based and recyclable material for AM feedstocks. Poly(lactic acid) (PLA) with wood flour (WF) is one composite system that has been demonstrated in numerous AM applications, as well as traditional processing methods (i.e., compression and injection molding); however, there has been a need to understand how the variation in processing methodology impacts the material performance of these bio-based feedstocks from a fundamental perspective, with particular emphasis on creep for an extended application use-life. Herein, PLA/WF is explored as a feedstock material for large format additive manufacturing (LFAM) and the performance of additively manufactured materials is compared to those produced via more traditional processing methods. It is also demonstrated that the addition of WF decreases the material’s coefficient of thermal expansion (CTE) while increasing its Young’s modulus, susceptibility to water uptake, and creep fatigue resistance. Essentially, the addition of 20 wt% WF results in a 92 % decrease in rubbery regime CTE while simultaneously resulting in a 14 % increase in modulus, 190 % increase in water uptake, and a 31 % decrease in residual strain after cyclic creep tests. The processing method was also found to play a large role in the final part performance, with the printed material increasing the crystallinity by 183 % and 214 % compared to its compression and injection molded counterparts. Furthermore, the porosity of printed samples increased by two orders of magnitude compared to samples prepared via traditional processing methods.
Ceramic materials are known for their high hardness and strength but are limited by low toughness and sudden failure. Inspired by the microstructure of dental enamel, which features undulating rods that promote crack deflection and energy absorption, architected specimens were designed and manufactured. A bespoke ball-on-ring (BoR) testing apparatus measured the static biaxial rupture strength of these bioinspired materials. Additionally, impact testing with spherical steel projectiles assessed their behavior under dynamic conditions. Monolithic alumina specimens were compared to architected alumina reinforced with yttria-stabilized zirconia (YSZ) rods produced via direct ink write 3D printing. BoR tests revealed that monolithic alumina had a Weibull modulus of 10.53 and a characteristic strength of 372.3 MPa, while the composite specimens showed a Weibull modulus of 5.46 and a characteristic strength of 213.3 MPa. Although the composite failed at lower stresses and projectile velocities, it exhibited notable crack deflection and fracture resistance, with cracks being effectively interrupted by the rod inclusions. The composite specimens also resulted in fewer and larger fragments upon impact. Finite element simulations confirmed the effectiveness of the rod structures in enhancing fracture resistance.
In order to investigate the effect of Fe on the equation of state (EOS), the volume of the perovskite (Pv) phases, (Mg{sub 1-x}Fe{sub x})SiO{sub 3}, with different Fe contents (x=0, 0.09, 0.15), has been measured at high pressures up to 1 Mbar in an Ar or NaCl medium. A bulk modulus (K{sub 0}) ranging between 255 and 261 GPa is obtained when the Au scales consistent with the Pt scale are used and the data are fit to the second order Birch-Murnaghan (BM) equation. When the third order BM equation is used, we obtain K{sub 0} = 250-264 GPa and K{sub 0}' = 3.7-4.5, which is consistent with previous low-pressure X-ray diffraction and Brillouin measurements. Within experimental uncertainties (0.5% in volume and 6% in bulk modulus), we do not resolve differences in the EOS between Fe-bearing (up to 15%) and Fe-free Pv to 1 Mbar (2600-km depth in the mantle). This is in contrast with the much larger effect of the Fe spin transition for the EOS of ferropericlase (Fp) reported recently. This is perhaps due to much more diverse states of Fe (e.g., oxidation, coordination, and spin states) in Pv than in Fp.
In situ synchrotron X-ray diffraction measurements are carried out on filled skutterudites CeFe{sub 4}Sb{sub 12} and Ce{sub 0.8}Fe{sub 3}CoSb{sub 12} up to 32 and 20 GPa, respectively, at room temperature. No phase transformation was observed for both samples in the pressure range. Fitting the pressure-volume data (up to 10 GPa) to the third-order Birch-Murnaghan equation of state, the bulk modulus B{sub 0} is determined to be 74(4) GPa, with the pressure derivative B'{sub 0} = 7(2) for CeFe{sub 4}Sb{sub 12}, and B{sub 0} = 71(2) GPa and B'{sub 0} = 8(2) for Ce{sub 0.8}Fe{sub 3}CoSb{sub 12}. The bulk moduli of filled skutterudites CeFe{sub 4}Sb{sub 12} and Ce{sub 0.8}Fe{sub 3}CoSb{sub 12} in our study are smaller than those from previous studies on unfilled skutterudite CoSb{sub 3}. The P-V curves of the unfilled skutterudite CoSb{sub 3} and filled skutterudites CeyFe{sub 4-x}Co{sub x}Sb{sub 12} showed good agreement, indicating that the Ce filling fraction and the replacement of Fe with Co have little effect on their compression behaviors.
Explore the source record for details and available documents.
Here, a sensitivity analysis on the failure probability of the Silicon Carbide (SiC) layer in tristructural isotropic (TRISO) nuclear fuel during transient conditions predicted by the BISON fuel performance code is performed. The principal goal of the analysis is to understand the most important parameters dictating SiC failure behavior in BISON during Reactivity Initiated Accidents (RIAs). SiC brittle fracture probability is modeled using Weibull statistics. A total of seven inputs related to SiC failure has been selected for the analysis, including the Weibull statistics parameters, elastic moduli for SiC and Pyrolitic Carbon (PyC) and SiC stress-free temperature. A 1D TRISO BISON model has been established for various reactivity insertions performed at the Nuclear Safety Research Reactor (NSRR). The principal advantage associated with the 1D TRISO model developed in this work is its computational efficiency. The Sobol variance decomposition method is used, and the sensitivity indices are presented for eight different values of the energy deposition. The results show that the two most important parameters impacting the predicted SiC failure probability are the Weibull modulus and the characteristic stress, and a co-variance amongst these parameters is obtained for low reactivity insertions. An additional new finding of this work is that the relative importance of Weibull parameters depends on the energy deposition, and thus reactivity, regime. For low energy depositions, two parameters are of influence on SiC failure probability, while for high energy depositions only one parameter impacts failure probability results. Moreover, optimization of the Weibull modulus and characteristic stress is performed by minimizing the RMSE between BISON failure probability predictions and experimental failure fractions for each energy deposition. This work also demonstrates the validity of the NSRR tests BISON simulations and of the respective sensitivity analysis results as conservative, yet indicative for slower transients characterized by lower deposited energies. Such verification is achieved through the partial extension of the analysis to a group Control Rod Withdrawal reproduced from a previous study. Another novel result of this analysis is that no single set of Weibull parameters can reproduce all reactivity insertion experimental failure results, which is related to the intrinsic nature of SiC failure properties, and a new range for the parameters is proposed to produce a failure probability envelope that encompasses the experimental fractions. Additionaly, this work proposes a new approach for future failure analysis with BISON, consisting in the use of Weibull parameters ranges, rather than fixed sets, along with failure envelopes generation.
Epoxy-nanocomposite resins filled with 12-nm spherical silica particles were investigated for their thermal and mechanical properties as a function of silica loading. The nanoparticles were easily dispersed with minimal aggregation for loadings up to 25 wt% as determined using transmission electron microscopy (TEM) and ultra-small-angle X-ray scattering (USAXS). A proportional decrease in cure temperatures and glass transition temperature (for loadings of 10 wt% and above) was observed with increased silica loading. The morphology determined by USAXS is consistent with a zone around the silica particles from which neighboring particles are excluded. The 'exclusion zone' extends to 10x the particle diameter. For samples with loadings less than 10 wt%, increases of 25% in tensile modulus and 30% in fracture toughness were obtained. More highly loaded samples continued to increase in modulus, but decreased in strength and fracture toughness. Overall, the addition of nanosilica is shown as a promising method for property enhancement of aerospace epoxy composite resins.