SEARCH · Search NASA
Results for “Phase Transformation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Crystallographic texture and microstructural changes in fusion welds of recrystallized Zry-4 rolled plates
This study presents a detailed characterization of the microstructural and crystallographic texture changes observed in the transition region in a weld between two Zircaloy-4 cold rolled and recrystallized plates. The microstructural study was performed by optical microscopy under polarized light and scanning electron microscopy (SEM). Texture changes were characterized at different lengthscales: in the micrometric size, orientation imaging maps (OIM) were constructed by electron backscatter diffraction (EBSD), in the millimetre scale, high energy XRD experiments were done at the Advanced Photon Source (USA) and compared to neutron diffraction texture determinations performed in the HIPPO instrument at Los Alamos National Laboratory. In the heat affected zone (HAZ) we observed the development of Widmanstätten microstructures, typical of the α( hcp ) to β( bcc ) phase transformation. Associated with these changes a rotation of the c-poles is found in the HAZ and fusion zone. While the base material shows the typical texture of a cold rolled plate, with their c-poles pointing 35° apart from the normal direction of the plate in the normal-transversal line, in the HAZ, c-poles align along the transversal direction of the plate and then re-orient along different directions, all of these changes occurring within a lengthscale in the order of mm. The evolution of texture in this narrow region was captured by both OIM and XRD, and is consistent with previous measurements done by Neutron Diffraction in the HIPPO diffractometer at Los Alamos National Laboratory, USA. The microstructural and texture changes along the HAZ were interpreted as arising due to the effect of differences in the cooling rate and β grain size on the progress of the different α variants during transformation. Fast cooling rates and large β grains are associated to weak variant selection during the β–>α transformation, while slow cooling rates and fine β grains result in strong variant selection.
Synchrotron x-Ray Study of Heterostructured Materials: A Review
Heterostructured materials (HSMs) have shown great potential for breaking the strength-ductility tradeoff. HSMs consist of heterogeneous zones that may have different sizes, shapes, compositions, structures, etc. Interactions and competitions among them often lead to unprecedented properties. However, due to the complex structures in a broad range of length scales, it is challenging to unravel deformation physics and strengthening mechanisms underlying extraordinary mechanical properties. Synchrotron x-rays provide powerful techniques and indispensable tools for investigating HSMs at various length scales. Here, we will present in situ high-energy x-ray diffraction and Laue x-ray microdiffraction techniques and their application in studying the HSMs. In this study, the principles of these techniques will be briefly introduced. We will focus on their application in studying stress partitioning and plastic accommodation during tensile deformation, thermo-driven and/or stress-driven phase transformations and various deformation microstructures like geometrically necessary dislocations and local stress/strain distributions, etc., in HSMs. Some important findings will be summarized. Challenging issues remain in studying HSMs and will be discussed.
Structural, morphological and dielectric properties of BiNbO{sub 4} ceramics prepared by the sol-gel method
Highlights: • The thermal treatment at 1200 °C generates a non-stoichiometric secondary phase. • The secondary phase Bi{sub 3.54}Nb{sub 7.09}O{sub 22.7}, is responsible for the highest Q × f and density. • The samples with triclinic BiNbO{sub 4} have the highest ε′. - Abstract: BiNbO{sub 4} ceramic powders were prepared using the sol-gel method. The fine particles were pressed into cylinders and, then, they were treated at temperatures between 500 and 1150 °C. The structure was studied by X-ray diffraction and Raman spectroscopy and the morphology was observed by scanning electron microscopy. The measurements of the complex permittivity were made in a resonant cavity operating at 2.7 GHz, using the small perturbation method. The reversible phase transformation between β-BiNbO{sub 4} and α-BiNbO{sub 4} was observed. The density, dielectric constant (ε') and the dielectric loss (tg δ) of the prepared powders increase with the sintering temperature, and the sample treated at 1150 °C shows the highest ε' and the highest Q × f.
Study of the interaction of solutes with Σ5 (013) tilt grain boundaries in iron using density-functional theory
Substitutional alloying elements significantly affect the recrystallization and austenite-ferrite phase transformation rates in steels. The atomistic mechanisms of their interaction with the interfaces are still largely unexplored. Using density functional theory, we determine the segregation energies between commonly used alloying elements and the Σ5 (013) tilt grain boundary in bcc iron. We find a strong solute-grain boundary interaction for Nb, Mo, and Ti that is consistent with experimental observations of the effects of these alloying elements on delaying recrystallization and the austenite-to-ferrite transformation in low-carbon steels. In addition, we compute the solute-solute interactions as a function of solute pair distance in the grain boundary, which suggest co-segregation for these large solutes at intermediate distances in striking contrast to the bulk.
An investigation of the reduction of TiO 2 by Mg in H 2 atmosphere
Hydrogen assisted magnesiothermic reduction (HAMR) of TiO 2 is a promising new process developed recently to produce Ti metal with low cost and less energy consumption. Here this work focuses on the understanding and optimization of the reduction process to control the quality of the reduced product. TiO 2 precursor particles with different relative densities were prepared, and the effects of the relative densities on reduction by Mg in H 2 were studied. The changes of oxygen contents vs. reduction time at various temperatures were investigated. The phase transformations during the reduction were analyzed both theoretically and experimentally. The relationship between the morphology of the reduced products and the relative densities of the TiO 2 precursors was analyzed by SEM characterization and the likely reason for the morphology evolution was discussed.
Synthesis, Structural Characterization, and Growth Mechanism of Li 1+ x V 3 O 8 Submicron Fibers for Lithium-Ion Batteries
Here, we report on the synthesis of submicron Li 1+x V 3 O 8 fibers through a facile mixed ethanol/water solution-mediated solvothermal route in the absence of surfactants. All the raw materials used are commercially available, relatively inexpensive, and low-toxic, and these can be handled in an ambient atmosphere, rendering this synthetic route as reasonably facile and efficient. To ensure a desirable and acceptable sample crystallinity and purity, we introduced a postannealing treatment at 500°C. The monoclinic phase formation of the fiber sample was probed in detail using a series of X-ray diffraction, scanning electron microscopy, transmission electron microscopy, infrared spectroscopy, X-ray photoelectron spectroscopy, high resolution transmission electron microscopy, and selected area electron diffraction measurements. Both morphology and chemical composition could be carefully and systematically tuned in terms of generating a class of novel, pure, and well-defined motifs of Li 1+x V 3 O 8 . A plausible mechanism for the formation of submicron-diameter fibers has been discussed in addition to the expected phase transformation within our Li-V-O materials. Our comprehensive study should provide for needed fundamental insights into putting forth a viable synthesis strategy for the generation of well-defined morphological variants of layered oxide materials for battery applications.
Synthesis method comparison of compositionally complex rare earth-based Ruddlesden–Popper n = 1 T'-type cuprates
The multicomponent approach has been successfully expanded to the Ruddlesden–Popper structure with the synthesis of two different high-entropy cuprate compositions: (La 0.2 Nd 0.2 Gd 0.2 Tb 0.2 Dy 0.2 ) 2 CuO 4 and (La 0.2 Pr 0.2 Nd 0.2 Sm 0.2 Eu 0.2 ) 2 CuO 4 . Additionally, the effect of synthesis method is explored using both solid-state reaction and polymeric steric entrapment (PSE) methods. It is found that PSE leads to more randomly distributed cation species, providing an advantageous method of synthesis for the growing field of high entropy oxides. In situ high-temperature x-ray diffraction tracks the amorphous to crystalline phase transformation in (La 0.2 Nd 0.2 Gd 0.2 Tb 0.2 Dy 0.2 ) 2 CuO 4 powder, synthesized using the PSE method. Using the High-Temperature XRD data, a method for gaining information on the kinetic behavior is also applied. Magnetometry of both compositions indicates ferrimagnetic behavior at low temperatures.
Unusual Temperature Dependence of Water Sorption in Semicrystalline Hydrogels
Abstract Water vapor sorption is a ubiquitous phenomenon in nature and plays an important role in various applications, including humidity regulation, energy storage, thermal management, and water harvesting. In particular, capturing moisture at elevated temperatures is highly desirable to prevent dehydration and to enlarge the tunability of water uptake. However, owing to the thermodynamic limit of conventional materials, sorbents inevitably tend to capture less water vapor at higher temperatures, impeding their broad applications. Here, an inverse temperature dependence of water sorption in poly(ethylene glycol) (PEG) hydrogels, where their water uptake can be doubled with increasing temperature from 25 to 50 °C, is reported. With mechanistic modeling of water–polymer interactions, this unusual water sorption is attributed to the first‐order phase transformation of PEG structures, and the key parameters for a more generalized strategy in materials development are identified. This work elucidates a new regime of water sorption with an unusual temperature dependence, enabling a promising engineering space for harnessing moisture and heat.
On Possible States of the Crystal Structure Preceding to a Phase Transition in Zn{sub 1 –} {sub x}V{sub x}Se (0.01 ≤ x ≤ 0.10) Crystals
The systematic new formations observed in the reciprocal lattice of the cubic structural modification of a II–VI compound are characterized using a detailed neutron diffraction study of bulk semiconducting ZnSe crystals with an increased vanadium content. Direct evidence that the additional sites k = (1/3 1/3 1/3) 2π/a (k is the wave vector and a is cubic unit cell parameter) observed by neutron scattering in the crystals, in the case when they belong to mutually penetrated rotated sublattices, contain a superstructure contribution formed by short-wave deformation, is obtained for the first time. This structure state is determined as a pretransition to the concentration fcc–hcp phase transformation, and the basis functions that allow one to analyze atomic displacements, the correlation between which create distortion-type superstructures, are indicated for the transition through one-arm channel, considering the transitions by the star of wave vector k{sub 5} of the fcc lattice.
Characterization of hot-pressed short ZrO{sub 2} fiber toughened ZrB{sub 2}-based ultra-high temperature ceramics
Two different ZrB{sub 2}-based ultra-high temperature ceramics were produced by hot pressing: ZrB{sub 2} + 20 vol.% SiC particle + 15 vol.% ZrO{sub 2} fiber and ZrB{sub 2} + 20 vol.% SiC whisker + 15 vol.% ZrO{sub 2} fiber. The microstructures were analyzed by using transmission electron microscopy and high-resolution transmission electron microscopy. It was shown that a clean interface without any impurities was identified in ZrB{sub 2}-based hybrid ceramics with SiC whiskers and ZrO{sub 2} fibers, which would significantly improve the toughening mechanism. The results of high-resolution transmission electron microscopy showed that stacking faults in SiC whiskers resulted from an insertion of a (111) layer, which would be one of the main reasons for material anisotropy. However, the interface between the SiC particle and ZrO{sub 2} fiber was found to be ambiguous in ZrB{sub 2}-based hybrid ceramics with SiC particles and ZrO{sub 2} fibers due to the slight reaction. The orientation relationship between t-ZrO{sub 2} and m-ZrO{sub 2} phases obeyed the classical correspondence: (100){sub m}//(100){sub t} and [001]{sub m}//〈001〉{sub t}, which further verified the feasibility of phase transformation toughening mechanism. - Highlights: • ZrB{sub 2}-based ceramics toughened by short ZrO{sub 2} fiber are characterized by TEM and HRTEM. • The orientation relationship of t- and m-ZrO{sub 2} are (100){sub m}//(100){sub t}, [001]{sub m}//〈001〉{sub t} • The clean interface without any impurities leads to improve the toughening mechanism.
High-Temperature Heat Capacity and Thermal Extension of FeTa{sub 2}O{sub 6}
The heat capacity of synthesized iron tantalate FeTa{sub 2}O{sub 6} was measured in the temperature range of 323–1103 K by the ratio method using a thermal analyzer combining thermogravimetry and scanning calorimetry. The temperatures of phase transformations were determined. Structural changes and thermal expansion of oxide were studied in the range of 300–1173 K by high-temperature X-ray diffraction. The temperature dependences of the unit cell parameters were approximated by third order polynomials. The values of thermal expansion coefficients and anisotropy factors were calculated based on the obtained data.
Structure, phase transitions, and isotope effects in [(CH3)4N]2PuCl6
The single crystal X-ray diffraction structure of [(CH3)4N]2PuCl6 is presented for the first time, resolving long standing confusion and speculation regarding the structure of this compound in the literature. A temperature dependent study of this compound shows that the structure of [(CH3)4N]2PuCl6 undergoes no fewer than two phase transitions between 100 and 360 K. The phase of [(CH3)4N]2PuCl6 at room temperature is Fd-3c a = 26.012(3) Å. At 360 K, the structure is in space group Fm-3m with a = 13.088(1) Å. The plutonium octahedra and tetramethylammonium cations undergo a rotative displacement and the degree of rotation varies with temperature, giving rise to the phase transition from Fm-3m to Fd-3c as the crystal is cooled. Synthesis and structural studies of the deuterated salt [(CD3)4N]2PuCl6 suggest that there is an isotopic effect associated with this phase transition as revealed by a changing transition temperature in the deuterated versus protonated compound indicating that the donor-acceptor interactions between the tetramethylammonium cations and the hexachloroplutonate anions are driving the phase transformation.
Shock-Driven Hydrodynamic Instability Growth Near Phase Boundaries and Material Property Transitions: Final Report
Activities for this grant included: 1) Development of dynamic impact experiments to probe strength and phase transition influence on dynamic deformation, 2) development of modern strength and phase aware simulation capabilities, 3) and post-processing of experimental data with simulation and closed form analytical techniques. Two different dynamic experiments were developed to probe material strengths in solid metals (largely copper and iron in this effort). In the first experiment a flyer plate impacts a flat target with an opposite rippled surface that is partially supported by a weaker window material. Post mortem analysis of the target sample showed a strong and repeatable residual plastic deformation dependence on grain orientation. Yield strengths for strain rates near 10 5 s -1 and plastic strains near ~50% were estimated to be around 180 to 240 MPa, varying in this range with grain orientation. Unfortunately dynamic real-time measurements were difficult with this setup due to diagnostic laser scattering; hence, an additional experimental setup was developed to complement these results. In the second set of experiments a rippled surface was ablated by a controlled laser pulsed, which launched a rippled shock front to an opposite initially flat diagnostic surface that was monitored in real-time with spatially resolved velocimetry techniques, e.g., line VISAR in addition to Transient Imaging Displacement Interferometry (TIDI) displacement measurements. This setup limited the displacements at the diagnostic surface to a reasonable level for TIDI measurements (~ less than one micrometer). These experiments coupled with analytical and numerical solutions provided evidence that viscous and elastic deviatoric strength affect shock front perturbation evolution in clearly different ways. Particularly, normalized shock front perturbation amplitudes evolve with viscosity (η) and perturbation wavelength (λ) as η/λ, such that increasing viscosity (or decreasing the initial wavelength) delays the perturbation decay. Conversely our experimental data, analysis and simulations show that for materials with elastic yield strength Y the normalized shock perturbation amplitude evolves with Yλ/A 0 , which shows wavelength increases have the opposite effect as in viscous materials and perturbation decay is also dependent on initial amplitude A 0 (viscous materials are independent of this parameter). Materials where strength had clear strain rate dependence, e.g., such as a PTW material law, behaved similarly to materials with only an effective yield stress (elastic-perfectly plastic) in the shock front perturbation studies obeying a Y eff λA 0 relationship where Y eff was a constant (near ~400 MPa for Cu for strain rates around 10 6 s -1 ). Magnitude changes in strain rate would increase Y eff as would be expected from the PTW behavior, but small perturbations (typical of regions behind the shock front) near a mean had little effect. Additional work based on simulations showed that phase transformation kinetics can affect the behavior of the perturbed shock front as well as the evolution of the RM-like instability that develops due to the imprint of the perturbed shock front on the initially flat surface as the shock breaks out.
Luminescence switching in Ce{sup 3+} ion sensitized YPO{sub 4}:Tb{sup 3+} through Redox reaction
Highlights: • Simple polyol method for preparation of Ce{sup 3+} sensitized Tb{sup 3+} ion doped YPO{sub 4} nanophosphor. • Enhanced green color emission with incorporation of Ce{sup 3+} ion into the matrix of YPO{sub 4}:Tb{sup 3+} nanophosphor. • Highly crystalline tetragonal YPO{sub 4}:Tb{sup 3+} without any impurity phase. • Use of alternate oxidising and reducing agent for luminescence switching (ON and OFF). - Abstract: Ce{sup 3+} sensitized Tb{sup 3+} ion doped YPO{sub 4} nanophosphor is synthesized by simple polyol method using ethylene glycol as capping agent as well as reaction medium. Green emission from Tb{sup 3+} ion doped YPO{sub 4} nanophosphor has been enhanced with incorporation of Ce{sup 3+} ion into the matrix of YPO{sub 4}:Tb{sup 3+}. XRD of YPO{sub 4}:Tb{sup 3+} annealed at 900 °C reveals crystalline tetragonal structure without any impurity phase. Morphology of YPO{sub 4}:Tb{sup 3+} nanophosphor was also studied. Homogenous incorporation of rare earth, RE (RE = Tb{sup 3+}, Ce{sup 3+}) ion into the host matrix were given in EDAX spectra. TGA/DTA analysis shows phase transformation of the as-prepared sample. Also, it is found that the as-prepared sample were readily re-dispersible in water due to presence of −OH group. By using an alternate oxidising and reducing agent, behaviour of luminescence switching (ON and OFF) can be examined. Lifetime decay of Tb{sup 3+} ion doped YPO{sub 4} nanophosphor was also studied.
Two-dimensional X-ray diffraction and transmission electron microscopy study on the effect of magnetron sputtering atmosphere on GaN/SiC interface and gallium nitride thin film crystal structure
The growth mechanisms of high quality GaN thin films on 6H-SiC by sputtering were investigated by X-ray diffraction (XRD) and scanning transmission electron microscopy (STEM). The XRD θ-2θ scans show that high quality (0002) oriented GaN was deposited on 6H-SiC by reactive magnetron sputtering. Pole figures obtained by 2D-XRD clarify that GaN thin films are dominated by (0002) oriented wurtzite GaN and (111) oriented zinc-blende GaN. A thin amorphous silicon oxide layer on SiC surfaces observed by STEM plays a critical role in terms of the orientation information transfer from the substrate to the GaN epilayer. The addition of H{sub 2} into Ar and/or N{sub 2} during sputtering can reduce the thickness of the amorphous layer. Moreover, adding 5% H{sub 2} into Ar can facilitate a phase transformation from amorphous to crystalline in the silicon oxide layer and eliminate the unwanted (33{sup ¯}02) orientation in the GaN thin film. Fiber texture GaN thin films can be grown by adding 10% H{sub 2} into N{sub 2} due to the complex reaction between H{sub 2} and N{sub 2}.
Pressure-induced kinetics of the a to x transition in zirconium
Abstract not provided
Modeling of melting and erosion in high velocity microparticle impacts
High velocity collisions can cause melting, a situation involving elasticity, plasticity, and phase transformations in tandem, which is very challenging for mechanical modeling. Here, this paper advances the use of smoothed particle hydrodynamics (SPH) simulations for this complex situation, investigating stainless steel microspheres impacting a tin substrate. After extensive validation against a range of mechanical and geometrical measurements of experimental impacts, the model provides a detailed, quantitative view of melt volume production over a broad range of impact velocities. It also enables direct decomposition of the impact energy partitioning, including analysis of the energy absorbed by plasticity in the impactor, the system kinetic energy, and the adiabatic heating of the substrate in addition to the melting itself. Since these quantities are not available experimentally, SPH modeling substantially enhances the quantitative understanding of such impacts. Finally, the model speaks to the phase characteristics of the ejecta formed during impact, confirming the experimental inference that the ejected material likely contains a significant fraction of solid material.