Search NASA⌕ Search

SEARCH · Search NASA

Results for “Relative positioning”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Lunar baselines and libration from differential VLBI observations of ALSEPs

Differential very-long-baseline interferometric observations of signals from Apollo Lunar Surface Experiment Package telemetry transmitters will yield the relative projected positions of the transmitters with uncertainty of only 1-3 m, set mainly by uncertainty of the lunar ephemeris. Noise and systematic instrumental errors which in the past affected similar observations have been reduced to the equivalent of a few centimeters on the lunar surface by the development of a new type of differential receiver. Continued observations should yield a determination of the motion of the moon about its center of mass with uncertainty less than 1 sec of selenocentric arc. Improvements (by other means) in our knowledge of the moon's orbital motion would allow a further order-of-magnitude refinement in the libration and relative position results obtainable by differential VLBI.

Counselman, C. C., III↗

Performance Assessment of Two GPS Receivers on Space Shuttle

Space Shuttle STS-69 was launched on September 7, 1995, carrying the Wake Shield Facility (WSF-02) among its payloads. The mission included two GPS receivers: a Collins 3M receiver onboard the Endeavour and an Osborne flight TurboRogue, known as the TurboStar, onboard the WSF-02. Two of the WSF-02 GPS Experiment objectives were to: (1) assess the ability to use GPS in a relative satellite positioning mode using the receivers on Endeavour and WSF-02; and (2) assess the performance of the receivers to support high precision orbit determination at the 400 km altitude. Three ground tests of the receivers were conducted in order to characterize the respective receivers. The analysis of the tests utilized the Double Differencing technique. A similar test in orbit was conducted during STS-69 while the WSF-02 was held by the Endeavour robot arm for a one hour period. In these tests, biases were observed in the double difference pseudorange measurements, implying that biases up to 140 m exist which do not cancel in double differencing. These biases appear to exist in the Collins receiver, but their effect can be mitigated by including measurement bias parameters to accommodate them in an estimation process. An additional test was conducted in which the orbit of the combined Endeavour/WSF-02 was determined independently with each receiver. These one hour arcs were based on forming double differences with 13 TurboRogue receivers in the global IGS network and estimating pseudorange biases for the Collins. Various analyses suggest the TurboStar overall orbit accuracy is about one to two meters for this period, based on double differenced phase residuals of 34 cm. These residuals indicate the level of unmodeled forces on Endeavour produced by gravitational and nongravitational effects. The rms differences between the two independently determined orbits are better than 10 meters, thereby demonstrating the accuracy of the Collins-determined orbit at this level as well as the accuracy of the relative positioning using these two receivers.

Schroeder, Christine A.↗

A cohesive zone treatment for the material point method involving problems of large deformation and damage

A new algorithm is described that permits the use of cohesive zones in the material point method for problems involving large deformation and fracture. In contrast to previous cohesive zone implementations, this method does not utilize massless surface-element particles. Instead, cohesive tractions are computed using the shape function mappings from a reference grid configuration in combination with explicitly defined particle surface normals and surface positions. These normals and relative surface positions are updated each time step according to particle deformation. The tractions are converted to cohesive forces using the nodal areas and mapped back to particles using the same reference shape function mappings. These forces are then remapped by conventional particle-to-grid interpolation as external forces using the current-configuration shape-function mappings. This allows highly compliant cohesive zones to function over jump displacements larger than a grid cell. Upon damage, these interfaces can revert to conventional multi-field contact surfaces. This approach is general and readily applies to two and three dimensions as well as being compatible with damage-field gradient partitioning offering exceptional computational flexibility. The framework for this method enables other capabilities, such as improved contact precision using explicitly defined surface normals and positions, and a method to mitigate spurious material damage at weak discontinuities between stiff brittle materials and soft or compliant materials.

Cohesive zone↗

Polarization switching characteristics of 0.5BaTi{sub 0.8}Zr{sub 0.2}O{sub 3}-0.5Ba{sub 0.7}Ca{sub 0.3}TiO{sub 3} lead free ferroelectric thin films by pulsed laser deposition

We report on the ferroelectricity for morphotropic-phase-boundary lead (Pb) free 0.5BaTi{sub 0.8}Zr{sub 0.2}O{sub 3}-0.5Ba{sub 0.7}Ca{sub 0.3}TiO{sub 3} (0.5BZT-0.5BCT) thin films. Thin films were grown on Pt/Ti/SiO{sub 2}/Si substrate using pulsed laser deposition. Raman spectroscopic data combined with the X-ray diffraction analyses confirm body centered tetragonal crystallographic structure 0.5BZT-0.5 BCT thin films on Pt/Ti/SiO{sub 2}/Si. Polarization studies demonstrate that these 0.5BZT-0.5BCT films exhibit a large remnant and saturation polarization of 37 μC/cm{sup 2} and 40 μC/cm{sup 2}, respectively, with a coercive field of 140 kV/cm. A correlation between polarization dynamics, structural distortion, and phonon vibration is established. The splitting of X-ray diffraction peak of the thin film in the 2θ range of 44.5° to 46.5° represents high degree of tetragonality. The tetragonality factor calculated by Rietveld analysis was found to be 0.006 and can be a major cause for the increased remnant polarization value. It is established from Raman spectra that the non-centrosymmetricity due to the displacement of Ti/Zr ions from its octahedral position is related to the peak position as well as the broadening of the A{sub 1} (LO) optical phonon mode. This increase of broadness in the thin film causes an increase in the dipole moment of the unit cell and, hence, the net increase in polarization values.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Usable Translational Hand Controllers for NASA's Habitability Design Center

This summer I was given the opportunity to work at the Habitability Design Center (HDC). NASA Johnson Space Center's HDC is currently developing Cislunar and Mars spacecraft mockups. I contributed to this effort by designing from scratch low cost, functional translational hand controllers (THCs) that will be used in spacecraft mission simulation in low to medium fidelity exploration spacecraft mockups. This project fell under the category of mechatronics, a combination of mechanical, electrical, and computer engineering. Being an aerospace engineering student, I was out of my comfort zone. And that was a wonderful thing. The autonomy that my mentor, Dr. Robert Howard, allowed me gave me the opportunity to learn by trying, failing, and trying again. This project was not only a professional success for me, but a significant learning experience. I appreciated the freedom that I had to take the time to learn new things for myself rather than blindly follow instructions. I was the sole person working on this project, and was required to work independently to solve the many hardware and software challenges that the project entailed. I researched THCs that have been used on the ISS, the Space Shuttle, and the Orion MPVC and based my design off of these. I worked through many redesigns before finding an optimal configuration of the necessary mechanisms and electrical components for the THC. Once I had a functional hardware design, I dove into the challenge of getting an Arduino Uno, an extremely low cost and easily programmable microcontroller, to behave as a human interface device. The THCs I built needed to be able to integrate to a mission simulation designed by NASA's Graphics and Visualization Lab. This proved to be the most challenging aspect of the project. To accomplish this I learned how to change the firmware of the USB serial converter microcontroller. The process was very complicated as it involved multiple software programs and manual flashing of pins on the Arduino itself. When I successfully achieved the goal I wrote an instructions manual for the process so that the HDC will be able to do this easily in the future for any human interface device they may want to create. I also created a detailed CAD model of my THC design with construction instructions. My THC utilizes three ultrasonic sensors, one for each axis of motion. I wrote a code that stimulates these sensors continuously and feeds back values from each axis ranging from -%100 to %100 of the min/max position in relation to the neutral position of each axis. This was the data that the Graphics and Visualization Lab required to interface with their simulation. I truly enjoyed working in the HDC surrounded by passionate, proactive, and brilliantly creative people. I felt valued and respected as a part of their team. I was given the time and support of my mentor whenever I asked for it. Beyond my positive project experience, I was fortunate enough to be able to take advantage of many of the extra activities that JSC has to offer. I took Russian Phase One during my lunch break every day and can now read Russian and accomplish basic verbal communication. I was heavily involved with the co-tern music video, which led to numerous incredible experiences and friendships. I saw every facility, attended every lecture, and met everyone that I could. I had coffee with Lauri Hansen. I played on an intern volleyball team at the Gilruth. I traveled to Michoud, Stennis, NOLA, and Big Bend National Park. I had the time of my life and I fell in love with JSC. In the next month I will return to Maryland and start my senior year of my undergraduate degree. As I work through it I will remember that all of the studying I do, all of the concentration I give, and all of the sacrifices that I make for school are so that I can work at a place like JSC where I am proud and excited to go into work every day. This internship was an invaluable experience for me, both professionally and personally.

Westbrook, Kimberly↗

SU-E-T-33: An EPID-Based Method for Testing Absolute Leaf Position for MLC Without Backup Jaws

Purpose: Methods in common use for MLC leaf position QA are limited to measurements relative to an arbitrary reference position. The authors previously presented an EPID-based method for efficiently testing accuracy of leaf position relative to the mechanical isocenter for MLC with backup jaws. The purpose of this work is to extend that method to the general case of MLC without backup jaws. Methods: A pair of collimator walkout images is used to determine the location of the mechanical isocenter relative to the center of one field using a parameter called X-offset. The method allows for shift of the imager panel to cover subsets of MLC leaves within the limited field of view of the imager. For a shifted panel position, an image of three beam strips defined by a subset of MLC leaves allows determination of the position of each leaf relative to the isocenter. The location of the isocenter is determined by applying X-offset to an image of a single rectangular field obtained at that panel position. The method can also be used to test backup jaws instead of MLC leaves. A software tool was developed to efficiently analyze the images. Results: The software tool reports leaf position and deviation from nominal position, and provides visual displays to facilitate rapid qualitative interpretation. Test results using this method agree well with results using the previous method requiring backup jaws. Test results have been successfully used to recalibrate one model MLC (Elekta MLCi2™). Work in progress includes extension of the software tool to other MLC models, and quantification of reproducibility of the measurements. Conclusion: This work successfully demonstrates a method to efficiently and accurately measure MLC leaf position, or backup jaw position, relative to the mechanical isocenter of the collimator.

60 APPLIED LIFE SCIENCES↗

UAS Well Clear Recovery Against Non-Cooperative Intruders Using Vertical Maneuvers

This paper documents a study that drove the development of a mathematical expression in the minimum operational performance standards (MOPS) of detect-and-avoid (DAA) systems for unmanned aircraft systems (UAS). This equation describes the conditions under which vertical maneuver guidance could be provided during recovery of well clear separation with a non-cooperative VFR aircraft in addition to horizontal maneuver guidance. Although suppressing vertical maneuver guidance in these situations increased the minimum horizontal separation from 500 to 800 feet, the maximum severity of loss of well clear increased in about 35 of the encounters compared to when a vertical maneuver was preferred and allowed. Additionally, analysis of individual cases led to the identification of a class of encounter where vertical rate error had a large effect on horizontal maneuvers due to the difficulty of making the correct left-right turn decision: crossing conflict with intruder changing altitude. These results supported allowing vertical maneuvers when UAS vertical performance exceeds the relative vertical position and velocity accuracy of the DAA tracker given the current velocity of the UAS and the relative vertical position and velocity estimated by the DAA tracker. Looking ahead, these results indicate a need to improve guidance algorithms by utilizing maneuver stability and near mid-air collision risk when determining maneuver guidance to regain well clear separation.

detect and avoid↗

Separating components of mixed fluid using a functionally graded material

A system for separating components of a fluid containing at least a first component and a second component includes a device having an inlet for introducing the fluid into the device, a first outlet for directing the first component of the fluid from the device, and a second outlet for directing the second component of the fluid from the device. A material that has a gradient in properties is located in the device between the inlet and the first and second outlets. The material has a first portion with an affinity for the first fluid component and a second portion with an affinity for the second fluid component. The first portion is positioned with relation to the first outlet such that the first component is directed from said device through the first outlet. The second portion is positioned with relation to the second outlet such that the second component is directed from the device through the second outlet.

42 ENGINEERING↗

A computer simulation approach to measurement of human control strategy

Human control strategy is measured through use of a psychologically-based computer simulation which reflects a broader theory of control behavior. The simulation is called the human operator performance emulator, or HOPE. HOPE was designed to emulate control learning in a one-dimensional preview tracking task and to measure control strategy in that setting. When given a numerical representation of a track and information about current position in relation to that track, HOPE generates positions for a stick controlling the cursor to be moved along the track. In other words, HOPE generates control stick behavior corresponding to that which might be used by a person learning preview tracking.

Green, J.↗

Approximate recoverability and relative entropy II: 2-positive channels of general von Neumann algebras

Abstract We generalize our results in paper I in this series to quantum channels between general von Neumann algebras, proving the approximate recoverability of states which undergo a small change in relative entropy through the channel. To this end, we derive a strengthened form of the quantum data processing inequality for the change in relative entropy of two states under a channel between two von Neumann algebras. Compared to the usual inequality, there is an explicit lower bound involving the fidelity between the original state and a recovery channel.

97 MATHEMATICS AND COMPUTING↗

Longitudinal Bunch Position Control for the Super-B Accelerator

The use of normal conducting cavities and an ion-clearing gap will cause a significant RF accelerating voltage gap transient and longitudinal phase shift of the individual bunches along the bunch train in both rings of the SuperB accelerator. Small relative centroid position shifts between bunches of the colliding beams will have a large adverse impact on the luminosity due to the small {beta}*{sub y} at the interaction point (IP). We investigate the possibility of minimizing the relative longitudinal position shift between bunches by reducing the gap transient in each ring and matching the longitudinal bunch positions of the two rings at the IP using feedback/feedforward techniques in the LLRF. The analysis is conducted assuming maximum use of the klystron power installed in the system.

43 PARTICLE ACCELERATORS↗

Holographic Noise in Interferometers

General arguments based on black hole evaporation, and on particular interpretations of holographic unification, suggest that there may be a new kind of indeterminacy in the relative transverse position of bodies in spacetime, corresponding to the diffraction limit of Planck wavelength radiation. Suitably designed instruments should display a new phenomenon, resembling a randomly varying shear in relative transverse position away from classical geodesics, with a flat power spectral density at low frequencies given approximately by the Planck time, and with no other parameters. An effective theory is presented to connect holographic unification with macroscopic phenomena, such as the statistical properties of noise in signals of interferometers. Macroscopic position operators in Matrix theory are interpreted to obey a Schr\'odinger wave equation, or equivalently a paraxial wave equation with a Planck frequency carrier, that connects longitudinal and transverse modes. A model based on gaussian-beam solutions of this equation is used to derive formulas in the time and frequency domain for autocorrelation of beamsplitter position in a Michelson interferometer. The cross-correlation of signals in two non-coincident interferometers as a function of separation is estimated. The cross-correlation signature may be exploited in the design of experiments to provide convincing evidence for or against the holographic hypothesis.

Hogan, Craig J.↗

Alignment positioning mechanism

An alignment positioning mechanism for correcting and compensating for misalignment of structures to be coupled is disclosed. The mechanism comprises a power screw with a base portion and a threaded shank portion. A mounting fixture is provided for rigidly coupling said base portion to the mounting interface of a supporting structure with the axis of the screw perpendicular thereto. A traveling ball nut threaded on the power screw is formed with an external annular arcuate surface configured in the form of a spherical segment and enclosed by a ball nut housing with a conforming arcuate surface for permitting gimballed motion thereon. The ball nut housing is provided with a mounting surface which is positionable in cooperable engagement with the mounting interface of a primary structure to be coupled to the supporting structure. Cooperative means are provided on the ball nut and ball nut housing, respectively, for positioning the ball nut and ball nut housing in relative gimballed position within a predetermined range of relative angular relationship whereby severe structural stresses due to unequal loadings and undesirable bending moments on the mechanism are avoided.

Fantasia, Peter M.↗

Estimability and simple dynamical analyses of range (range-rate range-difference) observations to artificial satellites

Non-Bayesian statistics were used in simulation studies centered around laser range observations to LAGEOS. The capabilities of satellite laser ranging especially in connection with relative station positioning are evaluated. The satellite measurement system under investigation may fall short in precise determinations of the earth's orientation (precession and nutation) and earth's rotation as opposed to systems as very long baseline interferometry (VLBI) and lunar laser ranging (LLR). Relative station positioning, determination of (differential) polar motion, positioning of stations with respect to the earth's center of mass and determination of the earth's gravity field should be easily realized by satellite laser ranging (SLR). The last two features should be considered as best (or solely) determinable by SLR in contrast to VLBI and LLR.

Vangelder, B. H. W.↗

Multi-wavelength Raman scattering of nanostructured Al-doped zinc oxide

In this work we present a detailed Raman scattering investigation of zinc oxide and aluminum-doped zinc oxide (AZO) films characterized by a variety of nanoscale structures and morphologies and synthesized by pulsed laser deposition under different oxygen pressure conditions. The comparison of Raman spectra for pure ZnO and AZO films with similar morphology at the nano/mesoscale allows to investigate the relation between Raman features (peak or band positions, width, relative intensity) and material properties such as local structural order, stoichiometry, and doping. Moreover Raman measurements with three different excitation lines (532, 457, and 325 nm) point out a strong correlation between vibrational and electronic properties. This observation confirms the relevance of a multi-wavelength Raman investigation to obtain a complete structural characterization of advanced doped oxide materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Fine Structure in the Secondary Electron Emission Peak for Diamond Crystal with (100) Negative Electron Affinity Surface

A fine structure was discovered in the low-energy peak of the secondary electron emission spectra of the diamond surface with negative electron affinity. We studied this structure for the (100) surface of the natural type-IIb diamond crystal. We have found that the low-energy peak consists of a total of four maxima. The relative energy positions of three of them could be related to the electron energy minima near the bottom of the conduction band. The fourth peak, having the lowest energy, was attributed to the breakup of the bulk exciton at the surface during the process of secondary electron emission.

Asnin, V. M.↗

The NSLS-II Components Relative Alignment Deviation Estimate

The alignment of NSLS-II components will be conducted under the constraint of survey control network. The control network system is categorized as outside, primary and secondary control networks, and all of them have random errors due to measurement random errors. In the error propagation point of view, they all will contribute to the final positioning accuracy of each component in global sense. However, as the global positioning requirement is relative loose (i.e. ± 3mm for storage ring), relative positioning accuracy is what we really concern. In this situation, only secondary control network will contribute as only secondary monuments will be employed to direct the adjustment of components. Other error sources include instrument setup error, adjustment residuals and slab movement etc. This article will analyze the maximum relative deviation of 3 positions in one cell’s region, which is a simulation of 1 ID and 2 Vacuum chamber positions.

43 PARTICLE ACCELERATORS↗