Search NASA⌕ Search

SEARCH · Search NASA

Results for “Vector Processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

NASA Tech Briefs, December 2003

Topics covered include: Organic/Inorganic Hybrid Polymer/Clay Nanocomposites; Less-Toxic Coatings for Inhibiting Corrosion of Aluminum; Liquid Coatings for Reducing Corrosion of Steel in Concrete; Processable Polyimides Containing APB and Reactive End Caps; Rod/Coil Block Copolyimides for Ion-Conducting Membranes; Techniques for Characterizing Microwave Printed Antennas; Cylindrical Antenna With Partly Adaptive Phased-Array Feed; Command Interface ASIC - Analog Interface ASIC Chip Set; Predicting Accumulations of Ice on Aerodynamic Surfaces; Analyzing Aeroelasticity in Turbomachines; Software for Allocating Resources in the Deep Space Network; Expert Seeker; High-Speed Recording of Test Data on Hard Disks; Functionally Graded Nanophase Beryllium/Carbon Composites; Thin Thermal-Insulation Blankets for Very High Temperatures; Aerostructures Test Wing; Flight-Test Evaluation of Flutter-Prediction Methods; Piezoelectrically Actuated Microvalve for Liquid Effluents; Larger-Stroke Piezoelectrically Actuated Microvalve; Innovative, High-Pressure, Cryogenic Control Valve: Short Face-to-Face, Reduced Cost; Safer Roadside Crash Walls Would Limit Deceleration; Improved Interactive Medical-Imaging System; Scanning Microscopes Using X Rays and Microchannels; Slotting Fins of Heat Exchangers to Provide Thermal Breaks; Methane Clathrate Hydrate Prospecting; Automated Monitoring with a BSP Fault-Detection Test; Automated Monitoring with a BCP Fault-Decision Test; Vector-Ordering Filter Procedure for Data Reduction; Remote Sensing and Information Technology for Large Farms; Developments at the Advanced Design Technologies Testbed; Spore-Forming Bacteria that Resist Sterilization; and Acoustical Applications of the HHT Method.

Source record↗
NASA NTRS2018

Sea State Based Estimation of White Cap Fraction: Implications for Primary Marine Aerosol Fluxes

Oceanic whitecaps (hereafter, W) or the characteristic whiteness of the sea foam is an important feature for predicting exchange of gases, sea spray aerosols (SSAs), heat and momentum transfer between the ocean and the atmosphere at the air-sea interface. Due to its increased surface emission and brightness temperature, whitecaps are critical for satellite retrievals of ocean albedo, ocean color, ocean surface wind vectors from satellite borne radiometer and microwave instruments. Most of the existing models predict W using wind speed and sea surface temperature (SST). However, numerous publications have pointed out that there are large uncertainties in the predicted W and using parameterizations based on wind-wave state can improve the precision of the predicted W. Here, we integrate the University of Miami Wave Model - 2.0 (UMWM) in Goddard Earth Observing System (GEOS) and use wave diagnostics to predict W. We choose the year 2006 for our global UMWM/GEOS runs because of the availability of W dataset from satellite observations. We run UMWM/GEOS at 0.5o x 0.5o by replaying to MERRA2 meteorology and evaluate the wave diagnostics using measurements from fixed buoys and satellite altimeters. We use three different parameterizations for W based on: 1) Reynolds number, 2) wave dissipation energy, and 3) volume of air entrained by breaking waves. We compare our results of W with previous studies and also with the satellite based observational dataset. Predicting W is important for understanding the processes at the air-sea interface. Therefore, this work is a step further in improving the uncertainties in the aerosol and atmospheric chemistry modules of the global models.

Oceanic Whitecaps↗
NASA NTRS2013

CRUQS: A Miniature Fine Sun Sensor for Nanosatellites

A new miniature fine Sun sensor has been developed that uses a quadrant photodiode and housing to determine the Sun vector. Its size, mass, and power make it especially suited to small satellite applications, especially nanosatellites. Its accuracy is on the order of one arcminute, and it will enable new science in the area of nanosatellites. The motivation for this innovation was the need for high-performance Sun sensors in the nanosatellite category. The design idea comes out of the LISS (Lockheed Intermediate Sun Sensor) used by the sounding rocket program on their solar pointing ACS (Attitude Control System). This system uses photodiodes and a wall between them. The shadow cast by the Sun is used to determine the Sun angle. The new sensor takes this concept and miniaturizes it. A cruciform shaped housing and a surface-mount quadrant photodiode package allow for a two-axis fine Sun sensor to be packaged into a space approx.1.25xl x0.25 in. (approx.3.2x2.5x0.6 cm). The circuitry to read the photodiodes is a simple trans-impedance operational amplifier. This is much less complex than current small Sun sensors for nanosatellites that rely on photo-arrays and processing of images to determine the Sun center. The simplicity of the circuit allows for a low power draw as well. The sensor consists of housing with a cruciform machined in it. The cruciform walls are 0.5-mm thick and the center of the cruciform is situated over the center of the quadrant photodiode sensor. This allows for shadows to be cast on each of the four photodiodes based on the angle of the Sun. A simple operational amplifier circuit is used to read the output of the photodiodes as a voltage. The voltage output of each photodiode is summed based on rows and columns, and then the values of both rows or both columns are differenced and divided by the sum of the voltages for all four photodiodes. The value of both difference over sums for the rows and columns is compared to a table or a polynomial fit (depending on processor power and accuracy requirements) to determine the angle of the Sun in the sensor frame.

Heatwole, Scott↗
NASA NTRS2014

America's Next Great Ship: Space Launch System Core Stage Transitioning from Design to Manufacturing

The Space Launch System (SLS) Program is essential to achieving the Nation's and NASA's goal of human exploration and scientific investigation of the solar system. As a multi-element program with emphasis on safety, affordability, and sustainability, SLS is becoming America's next great ship of exploration. The SLS Core Stage includes avionics, main propulsion system, pressure vessels, thrust vector control, and structures. Boeing manufactures and assembles the SLS core stage at the Michoud Assembly Facility (MAF) in New Orleans, LA, a historical production center for Saturn V and Space Shuttle programs. As the transition from design to manufacturing progresses, the importance of a well-executed manufacturing, assembly, and operation (MA&O) plan is crucial to meeting performance objectives. Boeing employs classic techniques such as critical path analysis and facility requirements definition as well as innovative approaches such as Constraint Based Scheduling (CBS) and Cirtical Chain Project Management (CCPM) theory to provide a comprehensive suite of project management tools to manage the health of the baseline plan on both a macro (overall project) and micro level (factory areas). These tools coordinate data from multiple business systems and provide a robust network to support Material & Capacity Requirements Planning (MRP/CRP) and priorities. Coupled with these tools and a highly skilled workforce, Boeing is orchestrating the parallel buildup of five major sub assemblies throughout the factory. Boeing and NASA are transforming MAF to host state of the art processes, equipment and tooling, the most prominent of which is the Vertical Assembly Center (VAC), the largest weld tool in the world. In concert, a global supply chain is delivering a range of structural elements and component parts necessary to enable an on-time delivery of the integrated Core Stage. SLS is on plan to launch humanity into the next phase of space exploration.

Birkenstock, Benjamin↗
NASA NTRSDate not supplied

Transcriptomics-based Machine Learning (ML) Analysis Predicts Space-Exposed Murine Livers

Limited sample sizes, high data dimensionality, and sensitivity to technical and biological variability of next generation sequencing (NGS), typically limits machine learning (ML) approaches in spaceflight studies that include radiation effects. However, pooling smaller studies while addressing intra- and inter-study variabilities allows for ML predictive modeling. Here, integration methods were applied to whole transcriptome shotgun sequencing (RNA-seq) data from six mouse liver GeneLab datasets (GLDS) (n ranging from 6 to 39 samples) from with a total of 81 spaceflight and ground-control samples to determine top features (i.e. genes) relevant to spaceflight including the effect of radiation exposure. RNASeq counts were normalized for each study, then merged and scaled across all datasets. Data dimensionality was reduced using a minimum redundancy maximum relevance (MRMR) methodology. Redundancy and relevance were computed using the Pearson correlation and F-statistic, respectively. The top 100 MRMR features were used to predict spaceflight vs. ground-control samples using Random Forest (RF), Support Vector Machine (SVM), and Linear Discriminant Analysis (LDA) classifiers with 5-fold cross validation (CV). Principal component analysis (PCA) on the complete feature set versus the MRMR features shows separation between spaceflight samples and ground controls (Figure 1A). The ML-based gene sets were compared against differential gene expression results obtained with DESeq2 from individual GLDS. Using all features or randomly sampled subsets at matching set sizes with MRMR, a maximum classifier accuracy of 69% on the test set over 5 folds. For all classifiers, CV training using at least the top 30 MRMR genes show minimum 89% accuracy and 0.95 AUC value on the test set over 5 folds (Figure 1B). Baseline set analysis on differentially expressed genes (DEGs) identified using padj ≤ 0.05 show 295 DEGs that overlap at least two studies and 13 DEGs that overlap three studies (Figure 1C). Set analysis between the top 100 MRMR features and the DEGs showed 47 genes that overlap at least one study and 24 genes that overlap two studies. Over-representation analysis showed overlapping biological processes related to fatty acid and lipid metabolism which may indicate these processes in the response to spaceflight stressors. MRMR feature selection for the selected ML methods improve performance relative to a classifier built on all features or randomly sampled subsets. Permutation feature importance within the decorrelated MRMR features showed concordance in feature ranking between ML methods. A challenge of applying ML methods across heterogeneous NGS data is accounting for signal:noise. Here, signal validation across studies was shown by intersecting sets between top MRMR genes and DEGs from DESeq2 analysis. Non-intersecting sets introduce opportunity to explore genes relevant to differentiating space flight exposed groups and implementing ML methods across existing NGS datasets may overcome sample size limitations.

Machine Learning↗
NASA NTRSDate not supplied

Transcriptomics-based Machine Learning Analysis Predicts Space-Exposed Murine Livers

Limited sample sizes, high data dimensionality, and sensitivity to technical and biological variability of next generation sequencing (NGS), typically limits machine learning (ML) approaches in spaceflight studies that include radiation effects. However, pooling smaller studies while addressing intra- and inter-study variabilities allows for ML predictive modeling. Here, integration methods were applied to whole transcriptome shotgun sequencing (RNA-seq) data from six mouse liver GeneLab datasets (GLDS) (n ranging from 6 to 39 samples) from with a total of 81 spaceflight and ground-control samples to determine top features (i.e. genes) relevant to spaceflight including the effect of radiation exposure. RNASeq counts were normalized for each study, then merged and scaled across all datasets. Data dimensionality was reduced using a minimum redundancy maximum relevance (MRMR) methodology. Redundancy and relevance were computed using the Pearson correlation and F-statistic, respectively. The top 100 MRMR features were used to predict spaceflight vs. ground-control samples using Random Forest (RF), Support Vector Machine (SVM), and Linear Discriminant Analysis (LDA) classifiers with 5-fold cross validation (CV). Principal component analysis (PCA) on the complete feature set versus the MRMR features shows separation between spaceflight samples and ground controls (Figure 1A). The ML-based gene sets were compared against differential gene expression results obtained with DESeq2 from individual GLDS. Using all features or randomly sampled subsets at matching set sizes with MRMR, a maximum classifier accuracy of 69% was shown on the test set over 5 folds. For all classifiers, CV training using at least the top 30 MRMR genes show minimum 89% accuracy and 0.95 AUC value on the test set over 5 folds (Figure 1B). Baseline set analysis on differentially expressed genes (DEGs) identified using padj ≤ 0.05 show 295 DEGs that overlap at least two studies and 13 DEGs that overlap three studies (Figure 1C). Set analysis between the top 100 MRMR features and the DEGs showed 47 genes that overlap at least one study and 24 genes that overlap two studies. Over-representation analysis showed overlapping biological processes related to fatty acid and lipid metabolism which may indicate these processes in the response to spaceflight stressors. MRMR feature selection for the selected ML methods improve performance relative to a classifier built on all features or randomly sampled subsets. Permutation feature importance within the decorrelated MRMR features showed concordance in feature ranking between ML methods. A challenge of applying ML methods across heterogeneous NGS data is accounting for signal:noise. Here, signal validation across studies was shown by intersecting sets between top MRMR genes and DEGs from DESeq2 analysis. Non-intersecting sets introduce opportunity to explore genes relevant to differentiating space flight exposed groups and implementing ML methods across existing NGS datasets may overcome sample size limitations.

Machine Learning↗
NASA NTRSDate not supplied

Transcriptomics-based Machine Learning Analysis Predicts Space-Exposed Murine Livers

Limited sample sizes, high data dimensionality, and sensitivity to technical and biological variability of next generation sequencing (NGS), typically limits machine learning (ML) approaches in spaceflight studies that include radiation effects. However, pooling smaller studies while addressing intra- and inter-study variabilities allows for ML predictive modeling. Here, integration methods were applied to whole transcriptome shotgun sequencing (RNA-seq) data from six mouse liver GeneLab datasets (GLDS) (n ranging from 6 to 39 samples) from with a total of 81 spaceflight and ground-control samples to determine top features (i.e. genes) relevant to spaceflight including the effect of radiation exposure. RNASeq counts were normalized for each study, then merged and scaled across all datasets. Data dimensionality was reduced using a minimum redundancy maximum relevance (MRMR) methodology. Redundancy and relevance were computed using the Pearson correlation and F-statistic, respectively. The top 100 MRMR features were used to predict spaceflight vs. ground-control samples using Random Forest (RF), Support Vector Machine (SVM), and Linear Discriminant Analysis (LDA) classifiers with 5-fold cross validation (CV). Principal component analysis (PCA) on the complete feature set versus the MRMR features shows separation between spaceflight samples and ground controls (Figure 1A). The ML-based gene sets were compared against differential gene expression results obtained with DESeq2 from individual GLDS. Using all features or randomly sampled subsets at matching set sizes with MRMR, a maximum classifier accuracy of 69% was shown on the test set over 5 folds. For all classifiers, CV training using at least the top 30 MRMR genes show minimum 89% accuracy and 0.95 AUC value on the test set over 5 folds (Figure 1B). Baseline set analysis on differentially expressed genes (DEGs) identified using padj ≤ 0.05 show 295 DEGs that overlap at least two studies and 13 DEGs that overlap three studies (Figure 1C). Set analysis between the top 100 MRMR features and the DEGs showed 47 genes that overlap at least one study and 24 genes that overlap two studies. Over-representation analysis showed overlapping biological processes related to fatty acid and lipid metabolism which may indicate these processes in the response to spaceflight stressors. MRMR feature selection for the selected ML methods improve performance relative to a classifier built on all features or randomly sampled subsets. Permutation feature importance within the decorrelated MRMR features showed concordance in feature ranking between ML methods. A challenge of applying ML methods across heterogeneous NGS data is accounting for signal:noise. Here, signal validation across studies was shown by intersecting sets between top MRMR genes and DEGs from DESeq2 analysis. Non-intersecting sets introduce opportunity to explore genes relevant to differentiating space flight exposed groups and implementing ML methods across existing NGS datasets may overcome sample size limitations.

Machine Learning↗
NASA NTRSDate not supplied

A Summary of the NEXT-C Flight Thruster Proto-flight Testing

Aerojet Rocketdyne (AR), under contract to NASA Glenn Research Center, built, tested and delivered the first flight version of the NEXT-C (NASA Evolutionary Xenon Thruster – Commercial) engine system. This system is comprised of a 7 kW thruster and power processing unit which are the commercial variants of the NEXT prototype thruster and power processing unit. In addition to developing the NEXT-C engine system for potential future NASA science missions, AR is dedicated to ensuring that this propulsion system is viable for commercial users and a wider variety of commercial applications. This paper will focus on the performance of the first flight model thruster, SN001, and presents an overview of the proto-flight testing environments and data obtained. For this first flight thruster, the proto-flight test sequence involved characterizing the performance of the thruster, in addition to vibration and thermal vacuum testing of the thruster. Between each of these environmental tests, the performance of the thruster was verified, ensuring that the environmental exposures, i.e. vibration and TVAC, did not affect the thruster performance. Specifically, the proto-flight data obtained included discharge chamber, optics and neutralizer performance. Faraday probe and ExB data obtained in the regions downstream of the thruster are presented and used to calculate thrust, and therefore specific impulse and total efficiency. Lastly, data are presented showing how the centroid of the ion beam, assumed to be indicative of the thrust vector location, varies throughout the entire proto-flight test campaign. The proto-flight testing of the NEXT-C PPU is documented in a previously published paper by Bontempo4. Following the proto-flight testing of the thruster, the thruster and its PPU successfully completed a System Integrated Test (SIT) tailored to the DART Mission. After the completion of the proto-flight testing, the SN001 thruster and SN002 PPU were delivered to APL for use on the DART mission.

Ion thruster↗
NASA NTRS2023

Modeling and Simulation for Exercise Vibration Isolation and Stabilization System Design

The microgravity environment that crew members experience on orbit presents a well-known health challenge, particularly when it comes to loss of muscle and bone mass. To counteract these negative effects, exercise countermeasures play a critical role in the daily routine of the crew on the International Space Station (ISS). To help inform requirements for upcoming exploration missions such as the Gateway Program, a new device, called the European Enhanced Exploration Exercise Device (E4D), is being built by the European Space Agency through their contractor, the Danish Aerospace Company. The E4D is being demonstrated on the ISS and is unique from other current exercise devices in that it provides four separate modalities in a single device: resistive, cycle ergometry, seated aerobic rowing, and rope pulling. To support the integration of E4D on ISS, a passive Vibration Isolation and Stabilization (VIS) system was required by NASA, and this responsibility was given to the Johnson Space Center. This paper describes the end-to-end process of modeling, simulation, and analysis used to inform the mechanical design of the VIS system. The process begins with the collection of representative exerciser motion capture (MoCap) through ground-based testing with the developmental E4D in both the Prototype Immersive Technology (PIT) Laboratory and the Active Response Gravity Offload System (ARGOS) facility at the Johnson Space Center. These collected MoCap data are processed through human biomechanics modeling to create forcing functions as input to a multibody dynamics simulation of the combined E4D/VIS system, with numerous resulting outputs. These outputs include microgravity accelerations, overall system displacements, internal and transmitted loads, as well as collisions. Microgravity accelerations are compared for compliance against ISS requirements while displacements are used for sway space determinations on the design and volumetric constraints within the targeted module. Internal loads are supplied to the supporting stress analysis teams and external loads for structural loads and dynamics teams, both at NASA and ESA. Finally, contact and clearance analysis is performed using the simulation to eliminate potential design issues. To ensure that the elements of the multibody simulation were verified and validated, correlation against multiple VIS related ground hardware testbeds was performed and characterized. In addition to the isolation part of the VIS problem, stabilization is also key to the integrated performance and evaluation. Due to the difficulty in defining ISS requirements in this area, the stability of the exerciser was inspected via analysis. Loss of balance was defined analytically as occurring when the resultant force vector acting on the exerciser lies outside the base of support of the feet. Both the VIS and E4D teams have recently gone through their Critical Design Reviews (CDRs) and the iterative model-based approach has been integral to inform mechanical design, particularly in the case of the VIS. This same end-to-end approach is now being applied for the Gateway Program, where an Exploration Exercise Device (EED) derived from the E4D and notional VIS for the device are under concept development.

Countermeasures↗
NASA NTRS1990

Recent experience with multidisciplinary analysis and optimization in advanced aircraft design

The task of modern aircraft design has always been complicated due to the number of intertwined technical factors from the various engineering disciplines. Furthermore, this complexity has been rapidly increasing by the development of such technologies as aeroelasticity tailored materials and structures, active control systems, integrated propulsion/airframe controls, thrust vectoring, and so on. Successful designs that achieve maximum advantage from these new technologies require a thorough understanding of the physical phenomena and the interactions among these phenomena. A study commissioned by the Aeronautical Sciences and Evaluation Board of the National Research Council has gone so far as to identify technology integration as a new discipline from which many future aeronautical advancements will arise. Regardless of whether one considers integration as a new discipline or not, it is clear to all engineers involved in aircraft design and analysis that better methods are required. In the past, designers conducted parametric studies in which a relatively small number of principal characteristics were varied to determine the effect on design requirements which were themselves often diverse and contradictory. Once a design was chosen, it then passed through the various engineers' disciplines whose principal task was to make the chosen design workable. Working in a limited design space, the discipline expert sometimes improved the concept, but more often than not, the result was in the form of a penalty to make the original concept workable. If an insurmountable problem was encountered, the process began over. Most design systems that attempt to account for disciplinary interactions have large empirical elements and reliance on past experience is a poor guide in obtaining maximum utilizations of new technologies. Further compounding the difficulty of design is that as the aeronautical sciences have matured, the discipline specialist's area of research has generally narrowed as more sophisticated methods are developed in the specialist's area of expertise. The results have been a decrease in the awareness of the impact of his decisions on other disciplines. This paper will outline the progress and problems encountered in the analysis, design, optimization sensitivity analysis, mathematical modeling, and configurations control and the means by which they are being solved. The breadth versus depth dilemma in analysis and design and the means for coping with that dilemma will be discussed. Finally, the all-important human aspects and the need for a new 'culture ' for doing business in an integrated, multidisciplinary design environment are discussed.

Dollyhigh, Samuel M.↗
NASA NTRS1999

Growth of Compound Semiconductors in a Low Gravity Environment: Microgravity Growth of PbSnTe

The growth of the alloy compound semiconductor lead tin telluride (PbSnTe) was chosen for a microgravity flight experiment in the Advanced Automated Directional Solidification Furnace (AADSF), on the United States Microgravity Payload-3 (USNP-3) in February, 1996 and on USNW- 4 in November, 1997. The objective of these experiments was to determine the effect of the reduction in convection, during the growth process, brought about by the microgravity environment. The properties of devices made from PbSnTe, an alloy of PbTe and SnTe, are dependent on the ratio of the elemental components in the starting crystal. Compositional uniformity in the crystal is only obtained if there is no significant mixing in the liquid during growth. The technological importance of PbSnTe lies in its band gap versus composition diagram which has a zero energy crossing at approximately 40% SnTe. This facilitates the construction of long wavelength (greater than 6 gm) infrared detectors and lasers. The properties and utilization of PbSnTe are the subject of other papers. 1,2 PbSnTe is also interesting from a purely scientific point of view. It is, potentially, both solutally and thermally unstable due to the temperature and density gradients present during growth. Density gradients, through thermal expansion, are imposed in directional solidification because temperature gradients are required to extract heat. Solutal gradients occur in directional solidification of alloys due to segregation at the interface. Usually the gradients vary with both experiment design and inherent materials properties. In a simplified one dimensional analysis with the growth axis parallel to the gravity vector, only one of the two instabilities work at a time. During growth, the temperature in the liquid increases ahead of the interface. Therefore the density, due to thermal expansion, is decreasing in that direction. However, the phase diagram shows that the lighter SnTe is preferentially rejected at the interface. This causes the liquid density to increase with distance away from the interface.

Fripp, A. L.↗
NASA NTRS2000

Ordering Unstructured Meshes for Sparse Matrix Computations on Leading Parallel Systems

The ability of computers to solve hitherto intractable problems and simulate complex processes using mathematical models makes them an indispensable part of modern science and engineering. Computer simulations of large-scale realistic applications usually require solving a set of non-linear partial differential equations (PDES) over a finite region. For example, one thrust area in the DOE Grand Challenge projects is to design future accelerators such as the SpaHation Neutron Source (SNS). Our colleagues at SLAC need to model complex RFQ cavities with large aspect ratios. Unstructured grids are currently used to resolve the small features in a large computational domain; dynamic mesh adaptation will be added in the future for additional efficiency. The PDEs for electromagnetics are discretized by the FEM method, which leads to a generalized eigenvalue problem Kx = AMx, where K and M are the stiffness and mass matrices, and are very sparse. In a typical cavity model, the number of degrees of freedom is about one million. For such large eigenproblems, direct solution techniques quickly reach the memory limits. Instead, the most widely-used methods are Krylov subspace methods, such as Lanczos or Jacobi-Davidson. In all the Krylov-based algorithms, sparse matrix-vector multiplication (SPMV) must be performed repeatedly. Therefore, the efficiency of SPMV usually determines the eigensolver speed. SPMV is also one of the most heavily used kernels in large-scale numerical simulations.

Oliker, Leonid↗
NASA NTRS2009

Structured DC Electric Fields With and Without Associated Plasma Density Gradients Observed with the C/NOFS Satellite

DC electric field observations and associated plasma drifts gathered with the Vector Electric Field Investigation on the Air Force Communication/Navigation Outage Forecasting System (C/NOFS) satellite typically reveal considerable variation at large scales (approximately 100's of km), in both daytime and nighttime cases, with enhanced structures usually confined to the nightside. Although such electric field structures are typically associated with plasma density depletions and structures, as observed by the Planar Langmuir Probe on C/NOFS, what is surprising is the number of cases in which large amplitude, structured DC electric fields are observed without a significant plasma density counterpart structure, including their appearance at times when the ambient plasma density appears relatively quiescent. We investigate the relationship of such structured DC electric fields and the ambient plasma density in the C/NOFS satellite measurements observed thus far, taking into account both plasma density depletions and enhancements. We investigate the mapping of the electric fields along magnetic field lines from distant altitudes and latitudes to locations where the density structures, which presumably formed the original seat of the electric fields, are no longer discernible in the observations. In some cases, the electric field structures and spectral characteristics appear to mimic those associated with equatorial spread-F processes, providing important clues to their origins. We examine altitude, seasonal, and longitudinal effects in an effort to establish the origin of such structured DC electric fields observed both with, and without, associated plasma density gradients

Pfaff, R.↗
NASA NTRSDate not supplied

Early Information Parameter-Set Analysis for Satellite Close Approaches using Machine Learning

Understanding orbital mechanics is essential in space flight and navigation applications, and leveraging modern force models for flight path projection remains an important aspect in space mission design and operation. However, force models do not capture all the dynamics or perturbations in the space environment and thus are subject to errors in predicting the state vectors. The further out the predicted miss distance between spacecraft is from the time of closest approach (TCA), the larger the propagated errors in the predicted miss distance at TCA is. The dependency on these force models for spacecraft flight state prediction calls for a more reliable method that can quantify, or even reduce, these propagated errors. With recent advances in the field artificial intelligence, specifically in machine and deep learning algorithms, a model that implements these approaches can improve on the modern force model approach. The goal for this work is to provide an early-information decision-making threshold, in order to prioritize risk assessment implementation, given the ongoing increase of space objects. In analyzing the relationship of several parameters from conjunction data messages(CDMs) and solar information, early information becomes viable in miss distance prediction with unsupervised learning techniques, which learn the parameters that are linked together with miss distance and probability of collision (Pc) variables. Another approach implemented for identifying relationships within CDMs is supervised learning, in which a shallow neural network binary classifier learns to distinguish events with Pc values¡108. These parameters detected in the unsupervised process are then applied to a regression neural network, which predicts the miss distance at TCA for a specific event within a given uncertainty bound. For the regression neural network, a Long Short Term Memory (LSTM) neural network is implemented, which yields memory about each time step in an event. Using an LSTM network, the model learns to predict miss distance within 0.2km of the value measured at TCA. Although there is a limited amount of "close miss" data to train a network, the network learns to associate parameters, like large energy dissipation rates with the secondary object, with an elevated Pc

Brianna I. Robertson↗
NASA NTRS2023

Effects of Optimisation Parameters on Data-Driven Magnetofrictional Modelling of Active Regions

Context . The solar magnetic field plays an essential role in the formation, evolution, and dynamics of large-scale eruptive structures in the corona. The estimation of the coronal magnetic field, the ultimate driver of space weather, particularly in the ‘low’ and ‘middle’ corona, is presently limited due to practical difficulties. Data-driven time-dependent magnetofrictional modelling (TMFM) of active region magnetic fields has been proven to be a useful tool to study the corona. The input to the model is the photospheric electric field that is inverted from a time series of the photospheric magnetic field. Constraining the complete electric field, that is, including the non-inductive component, is critical for capturing the eruption dynamics. We present a detailed study of the effects of optimisation of the non-inductive electric field on the TMFM of AR 12473. Aims . We aim to study the effects of varying the non-inductive electric field on the data-driven coronal simulations, for two alternative parametrisations. By varying parameters controlling the strength of the non-inductive electric field, we wish to explore the changes in flux rope formation and their early evolution and other parameters, for instance, axial flux and magnetic field magnitude. Methods . We used the high temporal and spatial resolution cadence vector magnetograms from the Helioseismic and Magnetic Imager (HMI) on board the Solar Dynamics Observatory (SDO). The non-inductive electric field component in the photosphere is critical for energising and introducing twist to the coronal magnetic field, thereby allowing unstable configurations to be formed. We estimated this component using an approach based on optimising the injection of magnetic energy. Results . Our data show that flux ropes are formed in all of the simulations except for those with the lower values of these optimised parameters. However, the flux rope formation, evolution and eruption time varies depending on the values of the optimisation parameters. The flux rope is formed and has overall similar evolution and properties with a large range of non-inductive electric fields needed to determine the non-inductive electric field component that is critical for energising and introducing twist to the coronal magnetic field. Conclusions . This study shows that irrespective of non-inductive electric field values, flux ropes are formed and erupted, which indicates that data-driven TMFM can be used to estimate flux rope properties early in their evolution without needing to employ a lengthy optimisation process.

A. Kumari↗
NASA NTRS1998

Tropospheric- Stratospheric Measurement Studies Summary

The two high altitude aircraft, ER-2 NASA #706 and 709 and the DC-8 NASA #717 are in active use in several programs of upper atmospheric research to study polar ozone changes, stratospheric-tropospheric exchange processes and atmospheric effects of aviation aircraft. The ER-2 has participated in seven major missions which mainly concentrated on vortex dynamics and the large losses of Ozone in the Polar regions (Ozone hole) observed in the spring. One mission verified the complex dynamical chemical and physical processes that occur during sunrise and sunset. Stratospheric Tracers of Atmospheric Transport (STRAT) obtained background measurements using the full ER-2 suite of instruments. Photochemistry of Ozone Loss in the Arctic Region in Summer (POLARIS) in 1997 assisted in understanding the mid-latitude and Arctic Ozone losses during the Northern Summer. The DC-8 with the Meteorological Measurement System (MMS) has participated in the Subsonic Aircraft: Cloud and Contrail Effects Special Study (SUCCESS), in 1996 and the Subsonic assessment Ozone and Nitrogen oxide experiment (SONEX) in 1997 missions. The MMS with its sophisticated software accurately measures ground speed and attitude, in-situ static and dynamic pressure total temperature, which are used to calculate the three dimensional wind fields, static pressure, temperature and turbulence values to meteorological accuracy. The meteorological data is not only of interest for its own sake in atmospheric dynamical processes such as mountain waves and flux measurements; but is also required by other ER-2 experiments that simultaneously measure water vapor, O3, aerosols, NO, HCl, CH4, N2O, ClO, BrO, CO2, NOy, HOx and temperature gradients. MMS products are extensively used to assist in the interpretation of their results in understanding the importance of convective effects relative to in-situ chemical changes, as may be noted by examining the list of references attached. The MMS consists of three subsystems: (a) aircraft instrumentation, inertial navigation system (INS), static and dynamic pressure taps, (b) additional dedicated instrumentation measuring angle of attack, yaw, total temperature, and a GPS which on the DC-8 measures position, velocity and attitude (c) an on board data, storage and computing acquisition system. This instrumentation and the associated software requires both an on-going laboratory ground calibration procedure for the total air temperature, static and total pressure inputs, verification of the INS dynamic response and also extensive air measurements and intercomparisons which ultimately verify and calibrate the complete system and its software. More than the usual accuracy is required because of the near cancellation occurring in the difference between the ground speed and true airspeed vectors used to give the wind vector. In the past year we have redesigned, recalibrated and used the MMS system on the NASA DC-8 that was previously used in the SUCCESS mission for the SONEX mission. Two papers were co-authored based on SUCCESS flights. Several reports and handouts were written for SONEX. Calibrations of the DC-8 pressure transducer temperature measuring thermistors was completed and an extensive analysis spanning several years of data files of the DC-8 Rosemount pressure transducer calibrations was done.

Browen, Stuart W.↗
NASA NTRS2004

Cirrus Clouds Optical, Microphysical and Radiative Properties Observed During Crystal-Face Experiment: I. A Radar-Lidar Retrieval System

A method of retrieving cloud microphysical properties using combined observations from both cloud radar and lidar is introduced. This retrieval makes use of an improvement to the traditional optimal estimation retrieval method, whereby a series of corrections are applied to the state vector during the search for an iterative solution. This allows faster convergence to a solution and is less processor intensive. The method is first applied to a synthetic cloud t o demonstrate its validity, and it is shown that the retrieval reliably reproduces vertical profiles of ice water content. The retrieval method is then applied to radar and lidar observations from the CRYSTAL-FACE experiment, and vertical profiles of ice crystal diameter, number concentration, and ice water content are retrieved for a cirrus cloud layers observed one day of that experiment. The validity of the relationship between visible extinction coefficient and radar reflectivity was examined. While synthetic tests showed such a functional relationship, the measured data only partially supported such a conclusion. This is due to errors in the forward model (as explained above) as well as errors in the data sets, including possible mismatch between lidar and radar profiles or errors in the optical depth. Empirical relationships between number concentrations and mean particle diameter were also examined. The results indicate that a distinct and robust relationship exists between these retrieved quantities and it is argued that such a relationship is more than an artifact of the retrieval process offering insight into the nature of the microphysical processes taking place in cirrus.

Mitrescu, C.↗
NASA NTRS2011

Lightweight High Efficiency Electric Motors for Space Applications

Lightweight high efficiency electric motors are needed across a wide range of space applications from - thrust vector actuator control for launch and flight applications to - general vehicle, base camp habitat and experiment control for various mechanisms to - robotics for various stationary and mobile space exploration missions. QM Power?s Parallel Path Magnetic Technology Motors have slowly proven themselves to be a leading motor technology in this area; winning a NASA Phase II for "Lightweight High Efficiency Electric Motors and Actuators for Low Temperature Mobility and Robotics Applications" a US Army Phase II SBIR for "Improved Robot Actuator Motors for Medical Applications", an NSF Phase II SBIR for "Novel Low-Cost Electric Motors for Variable Speed Applications" and a DOE SBIR Phase I for "High Efficiency Commercial Refrigeration Motors" Parallel Path Magnetic Technology obtains the benefits of using permanent magnets while minimizing the historical trade-offs/limitations found in conventional permanent magnet designs. The resulting devices are smaller, lower weight, lower cost and have higher efficiency than competitive permanent magnet and non-permanent magnet designs. QM Power?s motors have been extensively tested and successfully validated by multiple commercial and aerospace customers and partners as Boeing Research and Technology. Prototypes have been made between 0.1 and 10 HP. They are also in the process of scaling motors to over 100kW with their development partners. In this paper, Parallel Path Magnetic Technology Motors will be discussed; specifically addressing their higher efficiency, higher power density, lighter weight, smaller physical size, higher low end torque, wider power zone, cooler temperatures, and greater reliability with lower cost and significant environment benefit for the same peak output power compared to typically motors. A further discussion on the inherent redundancy of these motors for space applications will be provided.

Robertson, Glen A.↗