Search NASA⌕ Search

SEARCH · Search NASA

Results for “antenna arraying”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Direct-to-Earth Communications with Mars Science Laboratory During Entry, Descent, and Landing

Mars Science Laboratory (MSL) undergoes extreme heating and acceleration during Entry, Descent, and Landing (EDL) on Mars. Unknown dynamics lead to large Doppler shifts, making communication challenging. During EDL, a special form of Multiple Frequency Shift Keying (MFSK) communication is used for Direct-To-Earth (DTE) communication. The X-band signal is received by the Deep Space Network (DSN) at the Canberra Deep Space Communication complex, then down-converted, digitized, and recorded by open-loop Radio Science Receivers (RSR), and decoded in real-time by the EDL Data Analysis (EDA) System. The EDA uses lock states with configurable Fast Fourier Transforms to acquire and track the signal. RSR configuration and channel allocation is shown. Testing prior to EDL is discussed including software simulations, test bed runs with MSL flight hardware, and the in-flight end-to-end test. EDA configuration parameters and signal dynamics during pre-entry, entry, and parachute deployment are analyzed. RSR and EDA performance during MSL EDL is evaluated, including performance using a single 70-meter DSN antenna and an array of two 34-meter DSN antennas as a back up to the 70-meter antenna.

Direct-to-Earth (DTE)↗

Tactically Extensible and Modular Communications X-Band TEMCOM-X

This paper will discuss a CubeSat size (3U) telemetry system concept being developed at Marshall Space Flight Center (MSFC) in cooperation with the U.S. Department of the Army and Dynetics Corporation. This telemetry system incorporates efficient, high-bandwidth communications by developing flight-ready, low-cost, Proto-flight software defined radio (SDR) and Electronically Steerable Patch Array (ESPA) antenna subsystems for use on platforms as small as CubeSats and unmanned aircraft systems (UASs). Higher bandwidth capacity will enable high-volume, low error-rate data transfer to and from tactical forces or sensors operating in austere locations (e.g., direct imagery download, unattended ground sensor data exfiltration, interlink communications).

Sims, William H.↗

Tactically Extensible and Modular Communications - X-Band TEMCOM-X

This paper will discuss a proposed CubeSat size (3U) telemetry system concept being developed at Marshall Space Flight Center (MSFC) in cooperation with the U.S. Department of the Army and Dynetics Corporation. This telemetry system incorporates efficient, high-bandwidth communications by developing flight-ready, low-cost, Protoflight software defined radio (SDR) and Electronically Steerable Patch Array (ESPA) antenna subsystems for use on platforms as small as CubeSats and unmanned aircraft systems (UASs). The current telemetry system is slightly larger in dimension of footprint than required to fit within a 0.5U CubeSat volume. Extensible and modular communications for CubeSat technologies will partially mitigate current capability gaps between traditional strategic space platforms and lower-cost small satellite solutions. Higher bandwidth capacity will enable high-volume, low error-rate data transfer to and from tactical forces or sensors operating in austere locations (e.g., direct imagery download, unattended ground sensor data exfiltration, interlink communications), while also providing additional bandwidth and error correction margin to accommodate more complex encryption algorithms and higher user volume.

Sims, William Herbert↗

Wideband Instrument for Snow Measurements (WISM)

This presentation provides a brief summary of the utility of a wideband active and passive (radar and radiometer, respectively) instrument (8-40 GHz) to support the snow science community. The effort seeks to improve snow measurements through advanced calibration and expanded frequency of active and passive sensors and to demonstrate their science utility through airborne retrievals of snow water equivalent (SWE). In addition the effort seeks to advance the technology readiness of broadband current sheet array (CSA) antenna technology for spaceflight applications.

Radiometer↗

A Study of Flexible Composites for Expandable Space Structures

Payload volume for launch vehicles is a critical constraint that impacts spacecraft design. Deployment mechanisms, such as those used for solar arrays and antennas, are approaches that have successfully accommodated this constraint, however, providing pressurized volumes that can be packaged compactly at launch and expanded in space is still a challenge. One approach that has been under development for many years is to utilize softgoods - woven fabric for straps, cloth, and with appropriate coatings, bladders - to provide this expandable pressure vessel capability. The mechanics of woven structure is complicated by a response that is nonlinear and often nonrepeatable due to the discrete nature of the woven fiber architecture. This complexity reduces engineering confidence to reliably design and certify these structures, which increases costs due to increased requirements for system testing. The present study explores flexible composite materials systems as an alternative to the heritage softgoods approach. Materials were obtained from vendors who utilize flexible composites for non-aerospace products to determine some initial physical and mechanical properties of the materials. Uniaxial mechanical testing was performed to obtain the stress-strain response of the flexible composites and the failure behavior. A failure criterion was developed from the data, and a space habitat application was used to provide an estimate of the relative performance of flexible composites compared to the heritage softgoods approach. Initial results are promising with a 25% mass savings estimated for the flexible composite solution.

Scotti, Stephen J.↗

Wideband Instrument for Snow Measurements (WISM)

This presentation discusses current efforts to develop a Wideband Instrument for Snow Measurements (WISM). The objective of the effort are as follows: to advance the utility of a wideband active and passive instrument (8-40 gigahertz) to support the snow science community; improve snow measurements through advanced calibration and expanded frequency of active and passive sensors; demonstrate science utility through airborne retrievals of snow water equivalent (SWE); and advance the technology readiness of broadband current sheet array (CSA) antenna technology for spaceflight applications.

Radiometer↗

Self-Healing RF/Microwave Communications Circuits/Systems for NASA Missions—A Review

The success of current and future NASA missions relies in great part on the performance reliability and robustness of the communication circuits and systems of said missions. Some of the manifestations of reliability and robustness are comprised by properties such as graceful degradation, which provide redundancy and potentially longer life to the mission, and the ability to perform efficiently in harsh environments destinations such as Venus and the Jovian and Saturnian moons Europa and Enceladus, respectively. While several approaches have been considered or are currently underway to develop communications circuitry capable of performing in harsh environments, they lack the flexibility to enable reconfigurability to preserve functionality under adverse or contingency scenarios. This paper discusses some examples of self-healing RF/Microwave communications circuits and systems that could provide advantageous options in support of NASA missions.

self-healing↗

Self-Healing RF/Microwave Communications Circuits/Systems for NASA Missions - A Review

The success of current and future NASA missions relies in great part on the performance reliability and robustness of the communication circuits and systems of said missions. Some of the manifestations of reliability and robustness are comprised by properties such as graceful degradation, which provide redundancy and potentially longer life to the mission, and the ability to perform efficiently in harsh environments destinations such as Venus and the Jovian and Saturnian moons Europa and Enceladus, respectively. While several approaches have been considered or are currently underway to develop communications circuitry capable of performing in harsh environments, they lack the flexibility to enable reconfigurability to preserve functionality under adverse or contingency scenarios. This paper discusses some examples of self-healing RF/Microwave communications circuits and systems that could provide advantageous options in support of NASA missions.

Self-healing↗

Time series comparisons in Deep Space Network

The Deep Space Network (DSN) is NASA’s international array of antennas that support interplanetary spacecraft missions. DSN provides radar and radio astronomy observations that enhance our understanding of the solar system and the larger universe. A track is a block of continuous multi-dimensional time series from the beginning to end of DSN communication with the target spacecraft, containing 129 monitor data items lasting several hours at a frequency of 0.2-1Hz. Monitor data on each track reports on the performance of specific spacecraft operations and the DSN itself. DSN is receiving signals from 32 spacecraft across the solar system. DSN has pressure to reduce costs while maintaining the quality of support for DSN mission users. DSN operators need to simultaneously monitor multiple tracks and identify anomalies in real time. DSN has seen that as the number of missions increases, the data that needs to be processed increases over time. In this project, we look at the last 8 years of data for analysis. Any anomaly in the track indicates a problem with either the spacecraft, DSN equipment, or weather conditions. DSN operators typically write “discrepancy reports” for further analysis. It is recognized that it would be quite helpful to identify 10 similar historical tracks out of the huge database to quickly find/match anomalies. This tool has three functions: (1) identification of the top 10 similar historical tracks, (2) detection of anomalies compared to the reference normal track, and (3) comparison of statistical differences between two given tracks. The requirements for these features were confirmed by survey responses from 21 DSN operators and engineers. The preliminary machine learning model has shown promising performance (AUC=0.92). We plan to increase the number of data sets and perform additional testing to improve performance further before its planned integration into the Track Visualizer to assist DSN field operators and engineers.

Rebbapragada, Umaa↗

Experimental Setup for Mechanically Testing Subscale Triangular, Rollable, and Collapsible Deployable Composite Booms

High-strain composite deployable space structures are used for space infrastructure and science applications such as solar array supports, antennae, camera masts, and lightweight structures supporting solar sailing propulsion ele-ments. Triangular, Rollable, and Collapsible (TRAC) deployable composite booms are one example of a high-strain composite deployable structure and were studied using novel experimental test and characterization methods developed under the Gravity Offloading and Analysis of Long Imperfection-sensitive Ele-ments (GOALIE) project. In the present work, a subscale 7-m-long TRAC boom was suspended vertically to orient gravity along the length of the boom. By ori-enting vertically, highly nonlinear and unstable behavior often encountered dur-ing horizontally oriented gravity offload testing of similar structures was reduced. Pretest analytical predictions of TRAC booms indicated three unique failure modes, loads, and locations for three unique loading cases of in-plane bending, out-of-plane bending, and axial compression. To investigate the predicted behav-ior, an experimental test was set up to impart mechanical loads to a subscale TRAC boom. The experimental setup, loading cases, and instrumentation used to characterize the mechanical response of a subscale TRAC boom are described in this paper.

High-strain composites↗

Experimental Setup for Mechanically Testing Subscale Triangular, Rollable, and Collapsible Deployable Composite Booms

High-strain composite deployable space structures are used for space infrastructure and science applications such as solar array supports, antennae, camera masts, and lightweight structures supporting solar sailing propulsion elements. Triangular, Rollable, and Collapsible (TRAC) deployable composite booms are one example of a high-strain composite deployable structure and were studied using novel experimental test and characterization methods developed under the Gravity Offloading and Analysis of Long Imperfection-sensitive Elements (GOALIE) project. In the present work, a subscale 7-m-long TRAC boom was suspended vertically to orient gravity along the length of the boom. By orienting vertically, highly nonlinear and unstable behavior often encountered during horizontally oriented gravity offload testing of similar structures was reduced. Pretest analytical predictions of TRAC booms indicated three unique failure modes, loads, and locations for three unique loading cases of in-plane bending, out-of-plane bending, and axial compression. To investigate the predicted behavior, an experimental test was set up to impart mechanical loads to a subscale TRAC boom. The experimental setup, loading cases, and instrumentation used to characterize the mechanical response of a subscale TRAC boom are described in this paper.

Experimental testing↗

Active retrodirective antenna

Active antenna is self-phasing array which transmits signal in direction of remote pilot source. Word "active" means that transmitted power is generated by sources associated with antenna rather than by reflection of incident signal, as in passive retrodirective antenna. Array is also known as self-focusing array.

Chernoff, R. C.↗

Structurally Integrated Antenna Concepts for HALE UAVs

This technical memorandum describes work done in support of the Multifunctional Structures and Materials Team under the Vehicle Systems Program's ITAS (Integrated Tailored Aero Structures) Project during FY 2005. The Electromagnetics and Sensors Branch (ESB) developed three ultra lightweight antenna concepts compatible with HALE UAVs (High Altitude Long Endurance Unmanned Aerial Vehicles). ESB also developed antenna elements that minimize the interaction between elements and the vehicle to minimize the impact of wing flexure on the EM (electromagnetic) performance of the integrated array. In addition, computer models were developed to perform phase correction for antenna arrays whose elements are moving relative to each other due to wing deformations expected in HALE vehicle concepts. Development of lightweight, conformal or structurally integrated antenna elements and compensating for the impact of a lightweight, flexible structure on a large antenna array are important steps in the realization of HALE UAVs for microwave applications such as passive remote sensing and communications.

Cravey, Robin L.↗

SpiderFab: Process for On-Orbit Construction of Kilometer-Scale Apertures

The SpiderFab effort has investigated the value proposition and feasibility of radically changing the way we build and deploy spacecraft by enabling space systems to fabricate and integrate key components on-orbit. In this Phase II effort, we have focused on developing and demonstrating tools and processes to enable robotic systems to manufacture and assemble high performance structural elements that will serve as the support structures for components such as antennas and solar arrays. Through testing of these technologies in the laboratory environment,these efforts have established the technical feasibility of the key capabilities required for in-space manufacture of large apertures such as antennas, solar arrays, and optical systems,maturing prototype technical solutions for these capabilities to TRL-4. The SpiderFab effort has resulted in successful post-NIAC transition of the technology, first to SBIR-funded development of a technology for in-space manufacture (ISM) of truss structures, and then to a NASA/STMD Tipping Point Technologies funded effort to prepare a flight demonstration of ISM of a structure for a GEO communications satellite.

Manufacturing↗

Multiple beam phased array for Space Station Control Zone Communications

The Space Station Communications Control Zone is a disk shaped region 40 nautical miles in diameter and 10 nautical miles thick centered about the Space Station. It is estimated that 6 simultaneous Multiple Access (MA) channels will be required to satisfy the projected communications needs within this zone. These channels will be used to communicate with MA users located anywhere within the Control Zone. This paper details the tradeoffs and design implementation of a multiple beam integrated phased array to provide antenna coverage of the Control Zone. The array is a compact, modular assembly using Gallium Arsenide circuits, microstrip elements, and advanced packaging techniques. This results in a small, reliable antenna system capable of meeting the projected Space Station requirements and flexible enough to grow and evolve as the Space Station communications needs develop.

Halsema, P. B.↗

Lower-cost architectures for large arays of small antennas

Future plans for NASA's Deep Space Network (DSN) call for the construction of arrays of small antennas to compliment and eventually replace the existing network of large single antennas. The motivation for this transformation is the need to support much higher downlink data rates in the future, along with the realization that the most cost-effective way to do this is though a large increase in total collecting area on the ground. As currently designed, the DSN arrays will consist of approximately four hundred 12-m diameter antennas at each of three longitudes, operating at X and Ka bands (8 and 32 GHz).

small antennas↗

Computing Radiation From Multiple-Circular-Aperture Antennas

Mutual Coupling Program for Circular Waveguide-fed Aperture Array (CWG) computer program developed to calculate electromagnetic interactions among elements of antenna arrays with circular apertures with specified distributions of electromagnetic fields in apertures. Distributions assumed superpositions of electromagnetic modes existing in circular waveguide. Various external media included to provide flexibility of use; for example, flexibility to determine effects of dielectric covers upon impedances of aperture-type antennas. Written in VAX FORTRAN for DEC VAX-series computers running VMS (LAR-15236) and IBM PC-series and compatible computers running MS-DOS (LAR-15226).

Bailey, M. C.↗

Integrated Antenna/Solar Array Cell (IA/SAC) System for Flexible Access Communications

Present satellite communications systems normally use separate solar cells and antennas. Since solar cells generally account for the largest surface area of the spacecraft, co-locating the antenna and solar cells on the same substrate opens the possibility for a number of data-rate-enhancing communications link architecture that would have minimal impact on spacecraft weight and size. The idea of integrating printed planar antenna and solar array cells on the same surface has been reported in the literature. The early work merely attempted to demonstrate the feasibility by placing commercial solar cells besides a patch antenna. Recently, Integrating multiple antenna elements and solar cell arrays on the same surface was reported for both space and terrestrial applications. The application of photovoltaic solar cell in a planar antenna structure where the radiating patch antenna is replaced by a Si solar cell has been demonstrated in wireless communication systems (C. Bendel, J. Kirchhof and N. Henze, 3rd Would Photovotaic Congress, Osaka, Japan, May 2003). Based on a hybrid approach, a 6x1 slot array with circularly polarized crossdipole elements co-located on the same surface of the solar cells array has been demonstrated (S. Vaccaro, J. R. Mosig and P. de Maagt, IEEE Trans. Ant. and Propag., Vol. 5 1, No. 8, Aug. 2003). Amorphous silicon solar cells with about 5-10% efficiency were used in these demonstrations. This paper describes recent effort to integrate advanced solar cells with printed planar antennas. Compared to prior art, the proposed WSAC concept is unique in the following ways: 1) Active antenna element will be used to achieve dynamic beam steering; 2) High efficiency (30%) GaAs multi-junction solar cells will be used instead of Si, which has an efficiency of about 15%; 3) Antenna and solar cells are integrated on a common GaAs substrate; and 4) Higher data rate capability. The IA/SAC is designed to operate at X-band (8-12 GH) and higher frequencies Higher operating frequencies enable greater bandwidth and thus higher data transfer rates. The first phase of the effort involves the development of GaAs solar cell MIMs (Monolithically Integrated Module) with a single patch antenna on the opposite side of the substrate. Subsequent work will involve the integration of MIMs and antennas on the same side of the substrate. Results from the phase one efforts will be presented.

Lee, Ricard Q.↗