Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Low Regeneration Temperature Sorbents for Direct Air Capture of CO 2

Susteon Inc., in partnership with University of Wyoming and SoCalGas, successfully met all major technical objectives to (1) scale up the ionic liquid catalyst for amine-based sorbents for improved desorption and absorption kinetics, (2) evaluate the catalyzed amine-based sorbents for direct CO 2 capture process to determine CO 2 adsorption and desorption rates and energy requirements, and (3) based on the experimental results, develop a conceptual process design to perform a preliminary economic assessment to evaluate the potential for DAC process cost reduction using the catalyzed sorbents. Amine doped solid sorbents are effective for DAC applications and can be regenerated by heat or by a combination of heat, steam, and vacuum. The best sorbent composition identified was polyethyleneimine (PEI) on fumed silica with 200 ppm ionic liquid catalyst. This sorbent formulation was shown to have a CO 2 breakthrough capacity twice that of the non-catalyzed sorbent, in laboratory tests with air at 75% relative humidity (RH). The CO 2 adsorption rate was also 40% higher than that of the non-catalyzed sorbent. This type of sorbents has the attributes required for lowering the overall cost of DAC with high CO 2 capacity and high rate of adsorption. The combination of an industrially utilized amine-based sorbent with a highly active catalyst to form a new class of materials for DAC provides a technically viable pathway for reducing the cost of DAC to <$100/tonne of CO 2 . Laboratory measurements show that the silica/PEI (polyethyleneimine) sorbents with 100 ppm of ionic liquid catalyst have almost 100% higher CO 2 cyclic capacity and 40% higher adsorption rate. Generally, CO 2 desorption occurred at higher temperatures with a rate of desorption 10 times faster than adsorption (which occurred at ambient conditions). Therefore, adsorption rate is a much more important factor in the cost of DAC because it is directly linked to the CAPEX of the total system and the cycle time (i.e., sorbent productivity in ton/day of CO 2 captured per unit volume of the air contactor). An initial process design, coupled with techno-economic analysis, based on optimal experimental results and preliminary resulting from structured sorbent testing, showed a path to lower the DAC cost from the current cost of over $200/tonne CO 2 to less than $100/tonne with a scale-up, mature state of the technology, with projected material and process improvements. These results demonstrate the effectiveness of the catalyst in silica/PEI sorbents in enhancing sorbents’ CO 2 working capacity, in (a) increasing the rate of adsorption and desorption, and (b) in lowering the CAPEX and OPEX of the DAC system employing the ionic liquid catalyzed sorbents.

01 COAL, LIGNITE, AND PEAT↗

Insights into Supported Subnanometer Catalysts Exposed to CO via Machine-Learning-Enabled Multiscale Modeling

Subnanometer catalysts offer high noble metal utilization and superior performance for several reactions. However, understanding their structures and properties on an atomic scale under working conditions is challenging due to the large configurational space. Here, we introduce an efficient multiscale framework to predict their stability exposed to an adsorbate. The framework integrates a comprehensive toolset including density functional theory (DFT) calculations, cluster expansion, machine learning, and structure optimization. The end-to-end machine-learning workflow guides DFT data generation and enables significant computational acceleration. We demonstrate the approach for CO-adsorbed Pdn (n = 1–55) clusters on CeO 2 (111). Simulation results reveal that CO can facilitate restructuring by stabilizing smaller planar structures and bilayer structures of specific intermediate sizes, consistent with experimental reports. Metal–support interactions, preferential CO adsorption, and metal nuclearity and structure control catalyst stability. As a result, the framework allows automatic discovery of stable catalyst structures and a systematic strategy to exploit properties in the subnanometer scale.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Interpenetrating Triphase Cobalt-Based Nanocomposites as Efficient Bifunctional Oxygen Electrocatalysts for Long-Lasting Rechargeable Zn–Air Batteries

Rational construction of atomic-scale interfaces in multiphase nanocomposites is an intriguing and challenging approach to developing advanced catalysts for both oxygen reduction (ORR) and evolution reactions (OER). In this paper, a hybrid of interpenetrating metallic Co and spinel Co 3 O 4 “Janus” nanoparticles stitched in porous graphitized shells (Co/Co 3 O 4 @PGS) is synthesized via ionic exchange and redox between Co 2+ and 2D metal–organic-framework nanosheets. This strategy is proven to effectively establish highways for the transfer of electrons and reactants within the hybrid through interfacial engineering. Specifically, the phase interpenetration of mixed Co species and encapsulating porous graphitized shells provides an optimal charge/mass transport environment. Furthermore, the defect-rich interfaces act as atomic-traps to achieve exceptional adsorption capability for oxygen reactants. Finally, robust coupling between Co and N through intimate covalent bonds prohibits the detachment of nanoparticles. As a result, Co/Co 3 O 4 @PGS outperforms state-of-the-art noble-metal catalysts with a positive half-wave potential of 0.89 V for ORR and a low potential of 1.58 V at 10 mA cm -2 for OER. Finally, in a practical demonstration, ultrastable cyclability with a record lifetime of over 800 h at 10 mA cm -2 is achieved by Zn–air batteries with Co/Co 3 O 4 @PGS within the rechargeable air electrode.

25 ENERGY STORAGE↗

Solar light driven photocatalytic degradation of Ofloxacin based on ultra-thin bismuth molybdenum oxide nanosheets

Highlights: • Facile synthesis of ultra-thin Bi{sub 2}MoO{sub 6} nanosheets. • Solar-light driven photocatalytic degradation of antibiotic Ofloxacin. • Almost 70% photocatalytic degradation of Ofloxacin under optimized conditions. - Abstract: Herein, we report the facile synthesis, characterization and solar-light driven photocatalytic degradation of ultra-thin bismuth molybdenum oxide (Bi{sub 2}MoO{sub 6}) nanosheets. The nanosheets were synthesized by hydrothermal process and characterized using several techniques such as powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR), energy-dispersive X-ray spectroscopy (EDS), UV-diffusive reflectance spectroscopy (UV-DRS), transmission emission microscopy (TEM) and X-ray photon electron spectroscopy (XPS). The detailed morphological and structural studies confirmed the growth of ultra-thin Bi{sub 2}MoO{sub 6} nanosheets in large density with orthorhombic crystal structure. The calculated bandgap energy from Tauc’s plot for the synthesized nanosheets was found to be 2.73 eV, which shows maximum absorption toward higher wavelength. The XPS studies confirmed the successful formation Bi{sub 2}MoO{sub 6} nanosheets. The synthesized material was used as efficient solar light driven photocatalyst for the photocatalytic degradation of Ofloxacin. The mineralization of ofloxacin was confirmed using total organic carbon (TOC) analysis and photocatalytic experiments were performed under optimized conditions. It was observed that TOC value decreased with increasing the irradiation time. Under optimized photocatalytic degradation conditions, the observed extent of degradation was found to be ∼ 71%. The observed results confirm that the synthesized Bi{sub 2}MoO{sub 6} nanosheets are efficient and promising visible light responsive catalyst for the degradation of persistent organic pollutants.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Universal molecular-confined synthesis of interconnected porous metal oxides-N-C frameworks for electrocatalytic water splitting

The rational synthesis of high performance electrocatalysts at low cost for water splitting (hydrogen and oxygen evolution reaction, HER and OER) is highly desirable but remains a key challenge. Herein, we report a versatile molecular-confining route to construct strongly coupled metal oxides-N-C frameworks with interconnected configuration. By simply chelating various transition metal ions with ethylenediaminetetraacetic acid disodium salt (EDTA) in agarose hydrogel and subsequent carbonization, the high specific surface area porous N-C frameworks with strongly coupled metal oxides (e.g., manganese, iron, cobalt, nickel and their mixed oxides) can be prepared as advanced nonprecious water splitting electrocatalysts. For instance, the resulting Co 3 O 4 -N-C frameworks with the high surface area of 153 m 2 g -1 , and the moderate nitrogen content of 1.23%, require an overpotential of 324 mV to afford a current density of 10 mA cm -2 in 0.1 M KOH for OER, superior to commercial RuO 2 catalysts. Density functional theory (DFT) calculations reveal that the strong coupling between N-C and Co 3 O 4 tunes the local electronic structure of Co for high-valence active sites and assures optimal adsorption energies of OER intermediates. Moreover, Co 2 P-N-C electrocatalysts derived from Co 3 O 4 -N-C also exhibit excellent HER performance under 1.0 M KOH with a low overpotential of 139 mV to reach 10 mA cm -2 , a small Tafel slope of 45 mV dec -1 and impressive stability, underscoring the versatility of our synthetic strategy.

36 MATERIALS SCIENCE↗

Intermediate temperature fuel cells via an ion-pair coordinated polymer electrolyte

Fuel cells are attractive devices that convert chemical energy into electricity through the direct electrochemical reaction of hydrogen and oxygen. Intermediate temperature fuel cells operated at 200–300°C can simplify water and thermal managements, enable the use of non-precious or low-loading precious metal catalysts and provide insensitivity toward fuel and air impurities such as carbon monoxide. However, the performance of current intermediate temperature fuel cells is poor due to a lack of highly-conductive membrane electrolytes and optimal electrodes designed for these fuel cells. We demonstrate high-performing intermediate temperature fuel cells that use SnP 2 O 7 –polymer composite membranes and a quaternary ammonium-biphosphate ion-pair coordinated polymer electrolyte in the electrodes. The peak power density of the fuel cell under H 2 and O 2 reached 870 mW cm -2 at 240°C with minimal performance loss under exposure to 25% carbon monoxide.

30 DIRECT ENERGY CONVERSION↗

Biopolymer-supramolecular polymer hybrids for photocatalytic hydrogen production

Solar generation of H 2 is a promising strategy for dense energy storage. Supramolecular polymers composed of chromophore amphiphile monomers containing perylene monoimide (PMI) have been reported as crystalline light-harvesting assemblies for aqueous H 2 -evolving catalysts. Gelation of these supramolecular polymers with multivalent ions creates hydrogels with high diffusivity but insufficient mechanical stability and catalyst retention for reusability. We report here on using sodium alginate (SA) biopolymer to both induce supramolecular polymerization of PMI and co-immobilize them with catalysts in a robust hydrogel with high diffusivity that can also be 3D-printed. Faster mass transfer was achieved by controlling the material macrostructure by reducing gel diameter and microstructure by reducing biopolymer loading. Optimized gels produce H 2 at rates rivaling solution-based PMI and generate H 2 for up to 6 days. The PMI assemblies in the SA matrix create a percolation network capable of bulk-electron transfer under illumination. These PMI–SA materials were then 3D-printed on conductive substrates to create 3D hydrogel photoelectrodes with optimized porosity. The design of these versatile hybrid materials was bioinspired by the soft matter environment of natural photosynthetic systems and opens the opportunity to carry out light-to-fuel conversion within soft matter with arbitrary shapes and particular local environments.

36 MATERIALS SCIENCE↗

Application of differential resonant high-energy X-ray diffraction to three-dimensional structure studies of nanosized materials: A case study of Pt–Pd nanoalloy catalysts

Atoms in many of the increasingly complex nanosized materials of interest to science and technology do not necessarily occupy the vertices of Bravais lattices. The atomic scale structure of such materials is difficult to determine by traditional X-ray diffraction and so their functional properties remain difficult to optimize by rational design. Here, the three-dimensional structure of Pt x Pd 100– x nanoalloy particles is determined, where x = 0, 14, 36, 47, 64 and 100, by a non-traditional technique involving differential resonant high-energy X-ray diffraction experiments conducted at the K edge of Pt and Pd. The technique is coupled with three-dimensional modeling guided by the experimental total and element-specific atomic pair distribution functions. Furthermore, using DFT (density functional theory) calculation based on the positions of atoms in the obtained three-dimensional structure models, the catalytic performance of Pt–Pd particles is explained. Furthermore, differential resonant high-energy X-ray diffraction is shown to be an excellent tool for three-dimensional structure studies of nanosized materials. The experimental and modeling procedures are described in good detail, to facilitate their wider usage.

36 MATERIALS SCIENCE↗

Coal-Derived Warm Syngas Purification and CO 2 Capture-Assisted Methane Production

Gasifier-derived syngas from coal has many applications in the area of catalytic transformation to fuels and chemicals. Raw syngas must be treated to remove a number of impurities that would otherwise poison the synthesis catalysts. Inorganic impurities include alkali salts, chloride, sulfur compounds, heavy metals, ammonia, and various P, As, Sb, and Se- containing compounds. Systems comprising multiple sorbent and catalytic beds have been developed for the removal of impurities from gasified coal using a warm cleanup approach. This approach has the potential to be more economic than the currently available acid gas removal (AGR) approaches and improves upon currently available processes that do not provide the level of impurity removal that is required for catalytic synthesis application. Gasification also lends itself much more readily to the capture of CO 2 , important in the regulation and control of greenhouse gas emissions. CO 2 capture material was developed and in this study was demonstrated to assist in methane production from the purified syngas. Simultaneous CO 2 sorption enhances the CO methanation reaction through relaxation of thermodynamic constraint, thus providing economic benefit rather than simply consisting of an add-on cost for carbon capture and release. Molten and pre-molten LiNaKCO 3 can promote MgO and MgO-based double salts to capture CO 2 with high cycling capacity. A stable cycling CO 2 capacity up to 13 mmol/g was demonstrated. This capture material was specifically developed in this study to operate in the same temperature range and therefore integrate effectively with warm gas cleanup and methane synthesis. By combining syngas methanation, water-gas-shift, and CO 2 sorption in a single reactor, single pass yield to methane of 99% was demonstrated at 10 bar and 330°C when using a 20 wt% Ni/MgAl 2 O 4 catalyst and a molten-phase promoted MgO-based sorbent. Under model feed conditions both the sorbent and catalyst exhibited favorable stability after multiple test cycles. The cleanup for warm gas cleanup of inorganics was broken down into three major steps: chloride removal, sulfur removal, and the removal for a multitude of trace metal contaminants. Na 2 CO 3 was found to optimally remove chlorides at an operating temperature of 450ºC. For sulfur removal two regenerable ZnO beds are used for bulk H 2 S removal at 450ºC (<5 ppm S) and a non-regenerable ZnO bed for H 2 S polishing at 300ºC (<40 ppb S). It was also found that sulfur from COS could be adsorbed (to levels below our detection limit of 40 ppb) in the presence of water that leads to no detectable slip of H 2 S. Finally, a sorbent material comprising of Cu and Ni was found to be effective in removing trace metal impurities such as AsH 3 and PH 3 when operating at 300ºC. Proof-of-concept of the integrated cleanup process was demonstrated with gasifier-generated syngas produced at the Western Research Institute using Wyoming Decker Coal. When operating with a ~1 SLPM feed, multiple inorganic contaminant removal sorbents and a tar-reforming bed was able to remove the vast majority of contaminants from the raw syngas. A tar-reforming catalyst was employed due to the production of tars generated from the gasifier used in this particular study. It is envisioned that in a real application a commercial scale gasifier operating at a higher temperature would produce lesser amount of tar. Continuous operation of a poison-sensitive copper-based WGS catalyst located downstream from the cleanup steps resulted in successful demonstration.

54 ENVIRONMENTAL SCIENCES↗

Volcano‐like Activity Trends in Au@Pd Catalysts: The Role of Pd Loading and Nanoparticle Size

The addition of palladium (Pd) to preformed gold nanoparticles (Au NPs) enables the formation of core‐shell structures with enhanced catalytic performance in oxidation reactions. However, predicting the precise palladium content required to achieve maximum catalytic activity remains difficult based on current understanding. Herein, Pd was systematically introduced onto titania‐supported Au NPs (2, 6, and 10 nm) to evaluate their performance in benzyl alcohol oxidation. A volcano‐like trend in catalytic activity was observed, where activity increased with Pd addition, peaked, and then declined. The Pd loading required for maximum activity depended on Au NP size: ≈40 at% Pd/Au for 2.6 nm, ≈20 at% Pd/Au for 6.4 nm, and ≈12.5 at% Pd/Au for 10.6 nm. For Au NPs > 6 nm, peak activity aligned with monolayer Pd coverage, while for smaller NPs (2–3 nm), optimal Pd content was below monolayer predictions. X‐ray absorption spectroscopy revealed a core‐shell structure at low Pd content, but higher Pd loadings led to Pd diffusion into the Au core. This structural transformation likely caused activity decline, indicating that AuPd alloying negatively impacts catalysis. These results highlight that core‐shell Au@Pd catalysts outperform AuPd alloys and provide crucial insights for designing highly active bimetallic catalysts.

X-ray absorption spectroscopy↗

Design of a bifunctional TEMPO-tertiary amine mesoporous silica catalyst for the three-step cascade synthesis of a chromene derivative

A key challenge is design of materials and processes whereby competing reagents or conditions do not harm the multi-step sequence, thus allowing for more efficient chemical synthesis with elimination of work-up and separation steps. In this work, a three-step reaction cascade is performed using a porous bifunctional dimethylpropylamine-TEMPO-MCM41 catalyst, converting the commodity chemicals benzyl alcohol, sodium hypochlorite, and malononitrile to a biologically active anti-cancer, and anti-malarial 2-amino-chromene derivative. The cascade first utilizes a TEMPO-catalyzed oxidation of benzyl alcohol to benzaldehyde with NaOCl as the terminal oxidant. This is followed by a two-step, dual base catalyzed Knoevenagel condensation with malononitrile followed by a Michael addition with lawsone. Optimal conditions converting benzyl alcohol to 2-amino-5,10-dioxo-4-phenyl-5,10-dihydro-4H-benzo[g]chromene-3-carbonitrile include the delayed addition of malononitrile and lawsone during the three-step reaction sequence, which results in a 2-amino-chromene yield of over 80%. The importance of stepwise reagent addition is rationalized due to the unfavorable adsorption of acidic lawsone on the surface-grafted base catalyst. Tertiary Brønsted base sites of dimethylpropylamine outperform the more Lewis basic primary propylamine functionalized catalyst. This work outlines a simple and effective method for generating mesoporous materials with two types of active sites via co-condensation and thiol-ene coupling procedures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Developing reactors for electrifying bio-methanation: a perspective from bio-electrochemistry

The integration of microbial synthesis with renewable electricity is an emerging route for both CO 2 utilization and seasonal energy storage in the form of stored bio-electrofuels. The major benefits of electrifying bioreactors include: using highly selective bio-catalysts for CO 2 conversion under mild reaction conditions; decoupling the production of more facile electrochemical intermediates, such as hydrogen, at the electrode from the production of bio-catalyzed multi-electron and/or carbon products, such as methane or acetate; using microbes as robust and self-regenerating catalysts enabling higher efficiency and durability in CO 2 conversion systems compared to inorganic catalysis. In this Perspective, we propose research aimed at developing electro-bioreactor components that will increase the productivity of the reactor while maintaining high energy efficiency and biocompatible reaction conditions to fully realize the benefits of electrified bioreactors. Furthermore, these developments include: flow reactors with tailored 3D electrodes to optimally use the reactor volume, electrocatalysts designed for peak performance in neutral pH electrolytes, high conductivity microbial media, and new membrane separator materials with high ion conductivity and low gas permeability. Production of methane via a hybrid electrical-biological approach is taken as a case study to motivate these developments. Finally, an iterative design–manufacture–test cycle, enabled by additive manufacturing and 3D printing technologies, is proposed to rapidly prototype components prior to large-scale manufacturing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Next-Cycle Optimal Fuel Control for Cycle-to-Cycle Variability Reduction in EGR-Diluted Combustion

In this simulation study, cycle-to-cycle fuel control was used to reduce CCV by injecting additional fuel in operating conditions with sporadic misfires and partial burns. An optimal control policy was proposed that utilizes 1) a physics-based model that tracks in-cylinder gas composition and 2) a one-step-ahead prediction of the combustion efficiency based on a kernel density estimator. The optimal solution, however, presents a tradeoff between the reduction in combustion CCV and the increase in fuel injection quantity required to stabilize the charge. Such a tradeoff can be ad- just by a single parameter embedded in the cost function.

Maldonado, BryanP. [Oak Ridge National Lab. (ORNL)↗

Sustainable ammonia synthesis from nitrogen wet with sea water by single-step plasma catalysis

Ammonia synthesis at ambient conditions employing intermittent distributed green sources of energy and feedstocks is globally sought to replace the centralized Haber-Bosch (H-B) process operating at high temperature and pressure. We report herein for the first time an effective and sustainable ammonia synthesis pathway from N 2 wet with seawater vapor over spherical SiO 2 and M/SiO 2 (M: Ag, Cu, and Co) catalysts driven by non-thermal plasma (NTP). Experimental results indicate that the presence of a catalyst is required for ammonia production from seawater vapor and N 2 . The Co/SiO 2 catalyst delivered the highest ammonia synthesis rate (r NH 3 ) of 3.7 mmol g cat -1 h -1 and energy yield of 3.2 g NH 3 ∙kW -1 ∙h -1 at a relatively low input power of 2 W. The extraction of H atoms from H 2 O molecules plays an important role in the ammonia synthesis from seawater vapor. Finally, this work unfolds a novel platform for the subsequent optimization of sustainable ammonia production from endless resources such as seawater and N 2 through catalytic non-thermal plasma potentially powered by renewable sources.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

PdMo bimetallene for oxygen reduction catalysis

The efficient interconversion of chemicals and electricity through electrocatalytic processes is central to many renewable-energy initiatives. The sluggish kinetics of the oxygen reduction reaction (ORR) and the oxygen evolution reaction (OER) has long posed one of the biggest challenges in this field, and electrocatalysts based on expensive platinum-group metals are often required to improve the activity and durability of these reactions. The use of alloyingsurface strain and optimized coordination environments has resulted in platinum-based nanocrystals that enable very high ORR activities in acidic media; however, improving the activity of this reaction in alkaline environments remains challenging because of the difficulty in achieving optimized oxygen binding strength on platinum-group metals in the presence of hydroxide. Here we show that PdMo bimetallene—a palladium–molybdenum alloy in the form of a highly curved and sub-nanometre-thick metal nanosheet—is an efficient and stable electrocatalyst for the ORR and the OER in alkaline electrolytes, and shows promising performance as a cathode in Zn–air and Li–air batteries. The thin-sheet structure of PdMo bimetallene enables a large electrochemically active surface area (138.7 square metres per gram of palladium) as well as high atomic utilization, resulting in a mass activity towards the ORR of 16.37 amperes per milligram of palladium at 0.9 volts versus the reversible hydrogen electrode in alkaline electrolytes. This mass activity is 78 times and 327 times higher than those of commercial Pt/C and Pd/C catalysts, respectively, and shows little decay after 30,000 potential cycles. Density functional theory calculations reveal that the alloying effect, the strain effect due to the curved geometry, and the quantum size effect due to the thinness of the sheets tune the electronic structure of the system for optimized oxygen binding. Finally, given the properties and the structure–activity relationships of PdMo metallene, we suggest that other metallene materials could show great promise in energy electrocatalysis.

25 ENERGY STORAGE↗

Tandem bulk oxygen diffusion and surface reactions in reducible metal oxides control redox cycle dynamics

The interplay between bulk oxygen diffusion and surface reactions in reducible metal oxides is key in heterogeneous catalysts, but direct measurements of oxygen mobility, transient kinetics, and in situ spectroscopies have been lacking. Here, we reveal complex dynamic behavior of ceria-zirconia by H 2 using transient kinetics via mass spectrometry and in situ Raman and near-ambient pressure x-ray photoelectron spectroscopies. Molecular dynamics simulations with a machine learning potential delineate competitive oxygen diffusion mechanisms, with an optimal mobility at intermediate reductions. We expose a compensation between vacancy availability and lattice distortion at intermediate to high reductions and Frenkel defects at low reductions, underscoring a potential deficiency of 16 O/ 18 O exchange experiments in deducing oxygen mobility. Vacancies in proximity require electron localization on Ce atoms further away. The continuous replenishment of surface oxygen results in a varying reduction rate, with H 2 dissociation being the rate-limiting step. Multiscale transient simulations, consistent with experiments, indicate catalysts of potentially spatially varying oxidation states. The approach is broadly applicable to reducible oxide materials.

36 MATERIALS SCIENCE↗

Determination of Bulk and Surface Atomic Arrangement in Ni–Zn γ-Brass Phase at Different Ni to Zn Ratios

Previous attempts to characterize the γ-brass crystal structure of Ni–Zn (15.4–24% Ni) have failed to identify the location of the Ni and Zn atoms in the crystal lattice for more than 15.4% Ni content (Ni 8 Zn 44 ) due to the similar X-ray diffraction cross sections of Ni and Zn. Ni 8 Zn 44 is known to have a typical γ-brass crystal structure (space group 217, I$\overline{43}$m, 52 atom unit cell with four distinct symmetry positions: inner tetrahedral, outer tetrahedral, octahedral, and cuboctahedral) where Ni atoms reside in outer tetrahedral sites completely isolated from each other and coordinated by 12 Zn atoms. We utilize neutron diffraction to identify the substitution positions of Zn by Ni when the Ni content is increased above 15.4% and up to 19.2% (Ni 10 Zn 42 ). Upon increasing the Ni content above 15.4% (Ni 9 Zn 43 and Ni 10 Zn 42 ), Zn in the γ-brass octahedral positions are replaced by Ni leading to the formation of Ni–Ni–Ni trimers, which are absent in Ni8Zn44. Density functional theory (DFT) calculations confirm our neutron diffraction results regarding the optimal position of excess Ni in the γ-brass unit cell. The well-defined atomic site distribution in γ-brass Ni–Zn provides an excellent opportunity for producing site-isolated base metal catalysts that may find application in selective semi-hydrogenation. We investigated the presence of Ni–Ni–Ni trimers on the surface using H–D exchange and ethylene hydrogenation as probe reactions, observing the influence of Ni concentration on catalysis. We conclude the catalytic performance is insensitive to Ni content. We provide a possible explanation for this observation using DFT calculations, which demonstrate that surface containing trimer sites are energetically unfavorable and therefore not exposed on Wulff reconstructions of γ-brass phase Ni–Zn particles.

36 MATERIALS SCIENCE↗

Temperature and gas pressure effects in vertically aligned carbon nanotube growth from Fe-Mo catalyst

Vertically aligned carbon nanotubes are grown from Al 2 O 3 -supported Fe–Mo catalyst in a hot filament chemical vapor deposition apparatus. We compare the effect of carbon nanotube growth on deposition of 0.5 and 1 nm thick Fe catalyst layers before and after deposition of 0.1 and 0.2 nm thick layers of Mo. We observe that the order of deposition plays a role in the height of the nanotube arrays, especially evident during growth at elevated reaction pressures where carbon flux is higher. We investigate the role of temperature and pressure on features of the nanotube arrays such as height, alignment, quality, volumetric density, and diameter distribution for each of the catalyst thicknesses and for each case of Fe/Mo and Mo/Fe. We compare our results to those obtained from carpets grown from pure Fe catalyst, and observe that a Mo cocatalyst can be advantageous regardless of how it is deposited. Furthermore, we find that the order of deposition plays a key role in the temperature and pressure range in which optimal single-walled carbon nanotube growth occurs.

36 MATERIALS SCIENCE↗