Search NASA⌕ Search

SEARCH · Search NASA

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Development of flame and smoke retardant thermoplastic molding compounds

Compositions of polypropylene and ethylene-acrylic acid resins filled with high levels of alumina trihydrate of magnesium hydroxide were examined for smoke generation and impact resistance. Best results were obtained using alumina trihydrate coated with a low modulus elastomer, and ethylene-acrylic acid resin. Addition of polyvinyl alcohol fibers to the filled resin improves impact resistance and causes somewhat of an increase in smoke evolution.

Mueller, W. A.↗

Interfaces and failure mechanisms in Al-SiC composites

Aluminum alloys reinforced with silicon carbide whiskers exhibit significantly higher strength and modulus than the unreinforced alloys. However, the composites also exhibit low ductility and poor fracture toughness for reasons which are not well-understood. In this study, high resolution and conventional TEM techniques are used to analyze interface microstructure and failure mechanisms in P/M 2124 and 6061 aluminum alloys reinforced with silicon carbide whiskers. Interfacial oxides are typical of both composite materials, often distributed in clusters or in a discrete layer 2-5 nm thick along the whisker-matrix interface. Highly deformed regions beneath bulk tensile fracture surfaces reveal possible fracture nucleation centers as well as sites of stress concentration where intense plastic strain has occurred. Observations of such highly deformed regions include (1) void initiation at whisker ends, (2) interface decohesion involving the thin oxide layer, (3) transverse cracks in whiskers, and (4) cracks in large constituent particles. TEM results are presented and discussed in relation to mechanisms of composite failure.

Nutt, S. R.↗

Ab Initio Modeling of fcc Fe-Co-Cr-Ni High Entropy Alloys with Full Composition Range

The Fe-Co-Cr-Ni quaternary system has been studied extensively in the past decade, not only because of the superior properties achieved like high tensile ductility and fracture toughness, but also it is the foundation for the development of FeCrCoNi-based HEAs. However, most of the investigations are mainly focusing on the equiatomic and semi-equiatomic compositions. The physical properties of non-equiatomic compositions are barely explored. In the current work, the ab initio approach is adopted to predict the lattice parameter, structure stabilities, elastic properties, and enthalpy of formations of fcc Fe-Cr-Co-Ni HEA single crystals with the special quasirandom structure (SQS) method. To expand the design of Fe-Co-Cr-Ni HEAs into a full composition range, the current simulations cover all the binaries, ternaries, and the whole quaternary system. The 2-D composition-property contour diagrams are created to show the physical properties in the ternary and quaternary systems. Furthermore, our investigation shows that the fcc alloys' lattice parameter increases with the addition of Fe and Cr and decreases with Ni and Co. In addition to the enthalpy of formation at o K, the shape distortion rate is proposed to be another essential parameter to evaluate crystal stability. The results show the addition of Cr would destabilize the fcc lattice and cause symmetry breaking. Finally, the result of Pugh’s ratio shows that most of the fcc alloys show ductile behavior (P > 1.75), especially for the alloys around Fe 3 Ni, FeCo, and Fe 2 NiCo (P > 2.5). The brittle behavior (P < 1.75) is located around Fe 3 Cr and Fe 2 CoCr. Meanwhile, Cr 2 NiCo and Cr 2 FeNiCo are considered promising compositions to be tried and verified experimentally because of the higher bulk modulus and moderate shear modulus.

36 MATERIALS SCIENCE↗

Spin Transitions and Compressibility of ε-Fe 7 N 3 and γ'-Fe 4 N: Implications for Iron Alloys in Terrestrial Planet Cores

Iron nitrides are possible constituents of the cores of Earth and other terrestrial planets. Pressure-induced magnetic changes in iron nitrides and effects on compressibility remain poorly understood. In this work, we report synchrotron X-ray emission spectroscopy (XES) and X-ray diffraction (XRD) results for ε-Fe 7 N 3 and γ'-Fe 4 N up to 60 GPa at 300 K. The XES spectra reveal completion of high- to low-spin transition in ε-Fe 7 N 3 and γ'-Fe 4 N at 43 and 34 GPa, respectively. The completion of the spin transition induces stiffening in bulk modulus of ε-Fe 7 N 3 by 22% at ~40 GPa, but has no resolvable effect on the compression behavior of γ'-Fe 4 N. Fitting pressure-volume data to the Birch-Murnaghan equation of state yields V 0 = 83.29 ± 0.03 (Å 3 ), K 0 = 232 ± 9 GPa, K 0 ' = 4.1 ± 0.5 for nonmagnetic ε-Fe 7 N 3 above the spin transition completion pressure, and V 0 = 54.82 ± 0.02 (Å 3 ), K 0 = 152 ± 2 GPa, K 0 ' = 4.0 ± 0.1 for γ'-Fe 4 N over the studied pressure range. By reexamining evidence for spin transition and effects on compressibility of other candidate components of terrestrial planet cores, Fe 3 S, Fe 3 P, Fe 7 C 3 , and Fe 3 C based on previous XES and XRD measurements, we located the completion of high- to low-spin transition at ~67, 38, 50, and 30 GPa at 300 K, respectively. The completion of spin transitions of Fe 3 S, Fe 3 P, and Fe 3 C induces elastic stiffening, whereas that of Fe 7 C 3 induces elastic softening. Changes in compressibility at completion of spin transitions in iron-light element alloys may influence the properties of Earth's and planetary cores.

58 GEOSCIENCES↗

Smart Materials Behavior in Phosphates: Role of Hydroxyl Groups and Relevance to Antiwear Films

The elastic properties of materials under high pressure are relevant to the understanding and performance of many systems of current interest, for example, in geology and tribology. Of particular interest is the origin of the dramatic increase in modulus with increasing pressure, a response which is also called 'smart materials behavior.' In this context, simple phosphate-containing materials have been studied experimentally and theoretically, and the origins of this behavior have been associated with factors such as coordination of the cations and changes in the degree of polymerization and hydrogenation of the phosphate units. In the present paper we extend the former analysis on simple metal phosphate model compounds to so-called thermal films, an intermediate stage in the formation of effective antiwear films. The material was produced by heating a commercial zinc dialkyldithiophosphate (ZDDP), a common antiwear additive in lubricating oils, in poly-?-olefin base oil solutions to 150 degrees C, a process known to produce the thermal films. Its structure and equation of state were studied by means of x-ray diffraction and IR synchrotron radiation techniques during compression up to 25 GPa in a diamond anvil cell as well as during the subsequent decompression. As is the case for the simple metal phosphates, we find that the thermal films are relatively soft at low pressures but stiffen rapidly and ultimately amorphize irreversibly at high pressure. However, in addition to phase transformations involving cation sites occurring in the metal phosphates studied previously, thermal films undergo displacive transitions associated with instabilities of the hydroxyl groups. These results may imply that ZDDP ligands and those of the transformed materials not only affect ZDDP decomposition rate in engines but also the mechanical properties of the resulting antiwear films.

43 PARTICLE ACCELERATORS↗

Thermal equation of state of lower-mantle ferropericlase across the spin crossover

The thermal equation of state of ferropericlase [(Mg{sub 0.75}Fe{sub 0.25})O] has been investigated by synchrotron X-ray diffraction up to 140 GPa and 2000 K in a laser-heated diamond anvil cell. Based on results at high pressure-temperature conditions, the derived phase diagram shows that the spin crossover widens at elevated temperatures. Along the lower-mantle geotherm, the spin crossover occurs between 1700 km and 2700 km depth. Compared to the high-spin state, thermoelastic modeling of the data shows a {approx}1.2% increase in density, a factor of two increase in thermal expansion coefficient over a range of 1000 km, and a maximum decrease of 37% and 13% in bulk modulus and bulk sound velocity, respectively, at {approx}2180 km depth across the spin crossover. These anomalous behaviors in the thermoelastic properties of ferropericlase across the spin crossover must be taken into account in order to understand the seismic signatures and geodynamics of the lower mantle.

58 GEOSCIENCES↗

First Principle Mechanical and Thermodynamic Properties of Some TbX (X = S, Se) Compounds

The mechanical and thermodynamic results of some terbium chalcogenides, TbX (X = S, Se) compounds have been examined using full-potential linear augmented plane wave (FP-LAPW) method based on density functional theory. The local spin density approximation with Hubbard potential (LSDA+U) has been used for proper treatment of 4f-electrons of Tb. The magnetic moment of TbS and TbSe was calculated to be 5.44μ{sub B} and 5.57μ{sub B}, respectively. The ground state properties such as lattice parameter, bulk modulus, and pressure derivative of bulk modulus were obtained and found in good agreement with already available theory and experiment results. The mechanical properties such as Young modulus (E), shear modulus (G), Poisson ratio (υ), Cauchy pressure and B/G ratio were also predicted. Further, in thermodynamic properties, Debye temperatures (θ{sub D}), specific heats at constant volume(C{sub V}), thermal expansion co-efficient (α), and entropies (S) and their behavior with high temperature(0–1200 K) and pressure (0–50 GPa) were also predicted.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Dark matter and dark radiation from the early universe with a modulus coupled to the PQMSSM

The supersymmetrized DFSZ axion model is especially compelling in that it contains 1. the SUSY solution to the gauge hierarchy problem, 2. the Peccei-Quinn (PQ) solution to the strong CP problem and 3. the Kim-Nilles solution to the SUSY μ problem. In a string setting, where a discrete R-symmetry ($Z$$^{R}_{24}$ for example) may emerge from the compactification process, a high-quality accidental axion (accion) can emerge from the accidental, approximate remnant global U(1) PQ symmetry where the decay constant f a is linked to the SUSY breaking scale, and is within the cosmological sweet zone. In this setup, one also expects the presence of stringy remnant moduli fields Φ i . Here, we consider the situation of a single light modulus Φ coupled to the PQMSSM in the early universe, with mixed axion plus higgsino-like WIMP dark matter. We evaluate dark matter and dark radiation production via nine coupled Boltzmann equations and assess the severity of the cosmological moduli problem (CMP) along with dark matter and dark radiation production rates. We find that typically the light modulus mass should be m Φ ≳ 10 4 TeV to avoid the moduli-induced dark matter overproduction problem. If one is able to (anthropically) tune the modulus field amplitude, we find a value of Φ 0 ≲ 10 –7 m P would be required to solve the overall CMP.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

High pressure phase transformation in yttrium sulfide(YS): A first principle study

First principles calculations have been carried out to analyze structural, elastic and dynamic stability, of YS under hydrostatic compression. The comparison of enthalpies of rocksalt type (B1) and CsCl type cubic (B2) structures determined as a function of compression suggests the B1→B2 transition at ∼ 49 GPa. Various physical quantities such as zero pressure equilibrium volume, bulk modulus, and pressure derivative of bulk modulus have been derived from the theoretically determined equation of state. The single crystal elastic constants derived from the energy strain method agree well with the experimental values. The activation barrier between B1 and B2 phases calculated at transition point is ∼ 17/mRy/formula unit. Our lattice dynamic calculations show that at ambient condition, the B1 phase is lattice dynamically stable and frequencies of phonon modes in different high symmetry directions of Brillouin zone agrees well with experimental values. The B2 phase also is dynamical stable at ambient condition as well as at ∼ 49 GPa, supporting our static lattice calculation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Comparison of the high-pressure behavior of the cerium oxides C e 2 O 3 and Ce O 2

We studied the high-pressure behavior of Ce 2 O 3 using angle-dispersive x-ray diffraction to 70 GPa and compared with that of CeO 2 . Up to the highest pressure Ce 2 O 3 remains in the hexagonal phase (space group 164, P ¯32/m1) typical for the lanthanide sesquioxides. We did not observe a theoretically predicted phase instability for 30 GPa. The isothermal bulk modulus and its pressure derivative for the quasihydrostatic case are B 0 = 111 ± 2 GPa, B' 0 = 4.7 ± 0.3, and for the case without pressure-transmitting medium B 0 = 104 ±4 GPa, B' 0 = 6.5 ± 0.4. Starting from ambient-pressure magnetic susceptibility measurements for both oxides in highly purified form,we find that the Ce atom in Ce 2 O 3 behaves like a trivalent Ce 3+ ion (2.57μB per Ce atom) in contrast to previously published data. Since x-ray emission spectroscopy of the Lγ (4d 3/2 → 2p 1/2 ) transition is sensitive to the 4f -electron occupancy, we also followed the high-pressure dependence of this line for both oxides up to 50 GPa. We observed no change of the respective line shape, indicating that the 4f -electron configuration is stable for both materials. We posit from this data that the 4f electrons do not drive the volume collapse of CeO 2 from the high-symmetry, low-pressure fluorite structure to the lower-symmetry orthorhombic phase.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Insight into Phase Transition, Electronic, Magnetic, Mechanical, and Thermodynamic Properties of TbTe: a DFT Investigation

Theoretical investigation on TbTe for its structural, electronic, magnetic, and thermodynamic stuffs has been carried within density functional theory (DFT) as implemented in WIEN2K code. TbTe was found stable in ferromagnetic phase. The calculated ground-state parameters were found in a good agreement with the experimental data. The compound was found to have a structural stability in cubic B1 (NaCl-type structure) phase, but under the application of high pressure (at 27 GPa), it undergone to B2 (CsCl-type structure) phase of pressure. The second-order elastic constants and mechanical properties like Young’s modulus, Shear modulus, Poisson ratio, Cauchy pressure (C{sub 12}–C{sub 44}), and Pugh’s ratio (B/G) were calculated. The present calculations confirmed the ductile nature of TbTe. Further, the thermodynamic investigations have been carried using quasi-harmonic Debye approximation. We have calculated the pressure and temperature dependence of Debye temperature (𝜃{sub D}), bulk modulus (B), thermal expansion (α), heat capacities (C{sub V}), and entropy (S) in the temperature range of 0 to 1000 K and pressure range of 0 to 25 GPa.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Molecular-Dynamics Analysis of the Mechanical Behavior of Plasma-Facing Tungsten

We report a systematic computational analysis of the mechanical behavior of plasma-facing component (PFC) tungsten focusing on the impact of void and helium (He) bubble defects on the mechanical response beyond the elastic regime. Specifically, we explore the effects of porosity and He atomic fraction on the mechanical properties and structural response of PFC tungsten, at varying temperature and bubble size. We find that the Young modulus of defective tungsten undergoes substantial softening that follows an exponential scaling relation as a function of matrix porosity and He atomic content. Beyond the elastic regime, our high strain rate simulations reveal that the presence of nanoscale spherical defects (empty voids and He bubbles) reduces the yield strength of tungsten in a monotonically decreasing fashion, obeying an exponential scaling relation as a function of tungsten matrix porosity and He concentration. Our detailed analysis of the structural response of PFC tungsten near the yield point reveals that yielding is initiated by emission of dislocation loops from bubble/matrix interfaces, mainly 1/2<111> shear loops, followed by gliding and growth of these loops and reactions to form <100> dislocations. Furthermore, dislocation gliding on the <111>{211} twin systems nucleates 1/6<111> twin regions in the tungsten matrix. These dynamical processes reduce the stress in the matrix substantially. Subsequent dislocation interactions and depletion of the twin phases via nucleation and propagation of detwinning partials lead the tungsten matrix to a next deformation stage characterized by stress increase during applied straining. Furthermore, our structural analysis reveals that the depletion of twin boundaries (areal defects) is strongly impacted by the density of He bubbles at higher porosities. After the initial stress relief upon yielding, increase in the dislocation density in conjunction with decrease in the areal defect density facilitates the initiation of dislocation-driven deformation mechanisms in the PFC crystal.

36 MATERIALS SCIENCE↗

Few-cycle Regime Atomic Force Microscopy

Abstract Traditionally, dynamic atomic force microscopy (AFM) techniques are based on the analysis of the quasi-steady state response of the cantilever deflection in terms of Fourier analysis. Here we describe a technique that instead exploits the often disregarded transient response of the cantilever through a relatively modern mathematical tool, which has caused important developments in several scientific fields but that is still quite unknown in the AFM context: the wavelet analysis. This tool allows us to localize the time-varying spectral composition of the initial oscillations of the cantilever deflection when an impulsive excitation is given (as in the band excitation method), a mode that we call the few-cycle regime . We show that this regime encodes very meaningful information about the tip-sample interaction in a unique and extremely sensitive manner. We exploit this high sensitivity to gain detailed insight into multiple physical parameters that perturb the dynamics of the AFM probe, such as the tip radius, Hamaker constant, sample’s elastic modulus and height of an adsorbed water layer. We validate these findings with experimental evidence and computational simulations and show a feasible path towards the simultaneous retrieval of multiple physical parameters.

42 ENGINEERING↗

Irradiation-induced damage in concrete-forming aggregates: revisiting literature data through micromechanics

The radiation-induced volumetric expansion (RIVE) of aggregate-forming minerals causes damage in concrete exposed to high levels of fast neutrons fluence ( \(>\,\sim \,10^{19}\, \hbox {n}\,\hbox {cm}^{-2}\) at kinetics energy above 0.1 MeV). Historical post-irradiation RIVE and Young’s modulus data obtained in test reactors were revisited using a polycrystalline homogenization model (self-consistent scheme) accounting for the aggregates’ minerals content and the formation of voids/cracks during irradiation. It was found that the formation of extra voids/cracks can contribute to the aggregate expansion more substantially than the cumulated expansions of aggregate-forming minerals. Furthermore, the rate of void creation appears to be inversely correlated to the silica content, although aggregates of higher silicate contents exhibit higher RIVEs. The loss of Young’s modulus decreases exponentially with the aggregates’ expansion. At a comparable RIVE level, the relative loss of modulus is more significant in aggregates of higher silica content.

36 MATERIALS SCIENCE↗

Rheological survey of carbon fiber-reinforced high-temperature thermoplastics for big area additive manufacturing tooling applications

Carbon fiber (CF)-reinforced thermoplastic composites have been widely used in different structural applications due to their superior thermal and mechanical properties. The big area additive manufacturing (BAAM) system, developed at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility, has been used to manufacture several composite components, demonstration vehicles, molds, and dies. These components have been designed and fabricated using various CF-reinforced thermoplastics. In this study, the dynamic rheological and mechanical properties of a material commonly used in additive manufacturing, 20 wt% CF-acrylonitrile butadiene styrene (ABS), as well as three CF-reinforced high-temperature polymers, 25 wt% CF-polyphenylsulfone (PPSU), 35 wt% CF-polyethersulfone (PES), and 40 wt% CF-polyphenylene sulfide (PPS), used to print molds were investigated. The viscoelastic properties, namely storage modulus, loss modulus, tan delta, and complex viscosity, of these composites were studied, and the rheological behavior was related to the BAAM extrusion and bead formation process. The results showed 20 wt% CF-ABS and 40 wt% CF-PPS to display a more dominant elastic component at all frequencies tested while 25 wt% CF-PPSU and 35 wt% CF-PES have a more dominant viscous component. This viscoelastic behavior is then used to inform the deposition and bead formation process during extrusion on the BAAM system.

36 MATERIALS SCIENCE↗

Improved silicon carbide for advanced heat engines

Work performed to develop silicon carbide materials of high strength and to form components of complex shape and high reliability is described. A beta-SiC powder and binder system was adapted to the injection molding process and procedures and process parameters developed capable of providing a sintered silicon carbide material with improved properties. The initial effort has been to characterize the baseline precursor materials (beta silicon carbide powder and boron and carbon sintering aids), develop mixing and injection molding procedures for fabricating test bars, and characterize the properties of the sintered materials. Parallel studies of various mixing, dewaxing, and sintering procedures have been carried out in order to distinguish process routes for improving material properties. A total of 276 MOR bars of the baseline material have been molded, and 122 bars have been fully processed to a sinter density of approximately 95 percent. The material has a mean MOR room temperature strength of 43.31 ksi (299 MPa), a Weibull characteristic strength of 45.8 ksi (315 MPa), and a Weibull modulus of 8.0. Mean values of the MOR strengths at 1000, 1200, and 14000 C are 41.4, 43.2, and 47.2 ksi, respectively. Strength controlling flaws in this material were found to consist of regions of high porosity and were attributed to agglomerates originating in the initial mixing procedures. The mean stress rupture lift at 1400 C of five samples tested at 172 MPa (25 ksi) stress was 62 hours and at 207 MPa (30 ksi) stress was 14 hours. New fluid mixing techniques have been developed which significantly reduce flaw size and improve the strength of the material. Initial MOR tests indicate the strength of the fluid-mixed material exceeds the baseline property by more than 33 percent.

Whalen, T. J.↗