Search NASA⌕ Search

SEARCH · Search NASA

Results for “interphase”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Investigation of the Cathode–Catalyst–Electrolyte Interface in Aprotic Li–O 2 Batteries

Enabled by a unique integrated fabrication and characterization platform, X-ray photoelectron spectroscopy (XPS) studies reveal the formation of a thin solid electrolyte interphase (SEI) layer on a Li–O2 cathode after the first cycle. Subsequent cycling indicates that this SEI layer is very stable in terms of both chemistry and morphology, even after extensive cycling, preserving reversibility at the cathode/electrolyte interface. Remarkably, even after cell failure, replacement of the lithium anode resulted in recovery of the cycling behavior with the same cathode. These results demonstrate that chemical stabilization of the cathode/electrolyte interface promotes long-term operation of DMSO-based Li–O2 Ru-catalyzed batteries. Characterization of the Li anode surface reveals electrolyte decomposition, and a partial mechanism is proposed for the observed chemical composition of the cathode SEI. These studies are enabled by conformal deposition of a heterogeneous OER catalyst on a freestanding, binder-free, mesoporous, carbon-based Li–O2 cathode with high capacity and long-term cycling stability.

25 ENERGY STORAGE↗

First-Principles Modeling of Mn(II) Migration above and Dissolution from Li x Mn 2 O 4 (001) Surfaces

The density functional theory and ab initio molecular dynamics simulations are applied to investigate the migration of Mn(II) ions to above-surface sites on spinel Li x Mn 2 O 4 (001) surfaces, the subsequent Mn dissolution into the organic liquid electrolyte, and the detrimental effects on graphite anode solid electrolyte interphase (SEI) passivating films after Mn(II) ions diffuse through the separator. The dissolution mechanism proves complex; the much-quoted Hunter disproportionation of Mn(III) to form Mn(II) is far from sufficient. Key steps that facilitate Mn(II) loss include concerted liquid/solid-state motions; proton-induced weakening of Mn–O bonds forming mobile OH – surface groups; and chemical reactions of adsorbed decomposed organic fragments. Mn(II) lodged between the inorganic Li 2 CO 3 and organic lithium ethylene dicarbonate (LEDC) anode SEI components facilitate electrochemical reduction and decomposition of LEDC. Our findings help inform future design of protective coatings, electrolytes, additives, and interfaces.

36 MATERIALS SCIENCE↗

A new anion receptor for improving the interface between lithium- and manganese-rich layered oxide cathode and the electrolyte

Surface degradation on cycled lithium-ion battery cathode particles is governed not only by intrinsic thermodynamic properties of the material but also, oftentimes more predominantly, by the side reactions with the electrolytic solution. A superior electrolyte inhibits these undesired side reactions on the cathode and at the electrolyte interface, which consequently minimizes the deterioration of the cathode surface. The present study investigates a new boron-based anion receptor, tris(2,2,2-trifluoroethyl)borate (TTFEB), as an electrolyte additive in cells containing a lithium- and manganese-rich layered oxide cathode, Li 1.16 Ni 0.2 Co 0.1 Mn 0.54 O 2 . Our electrochemical studies demonstrate that the cycling performance and Coulombic efficiency are significantly improved because of the additive, in particular, under elevated temperature conditions. Spectroscopic analyses revealed that the addition of 0.5 wt % TTFEB is capable of reducing the content of lithium-containing inorganic species within the cathode-electrolyte interphase layer and minimizing the reduction of tetravalent Mn4+ at the cathode surface. Furthermore, our work introduces a novel additive highly effective in improving lithium-ion battery performance, highlights the importance in preserving the surface properties of cathode materials, and provides new insights on the working mechanism of electrolyte additives.

25 ENERGY STORAGE↗

Effects of Anion Mobility on Electrochemical Behaviors of Lithium–Sulfur Batteries

The electrolyte is a crucial component of lithium-sulfur (Li-S) batteries, as it controls polysulfide dissolution, charge shuttling processes, and solid-electrolyte interphase (SEI) layer formation. Experimentally, the overall performance of Li-S batteries varies with choice of solvent system and Li-salt used in the electrolyte, and a lack of predictive understanding about the effects of individual electrolyte components inhibits the rational design of electrolytes for Li-S batteries. Here we analyze the role of the counter anions of common Li salts (such as TfO-, FSI-, TFSI-, and TDI-) when dissolved in DOL/DME (1:1 vol.) for use in Li-S batteries. The evolution of ion-ion and ion-solvent interactions due to vari-ous anions was analyzed using 17O NMR and pulsed-field gradient (PFG) NMR and then correlated with electrochemi-cal performance in Li-S cells. These data reveal that the for-mation of the passivation layer on the anode and the loss of active materials from the cathode (evidenced by polysulfide dissolution) are related to anion mobility and affinity with lithium polysulfide, respectively. For future electrolyte de-sign, anions with lower mobility and weaker interactions with lithium polysulfides may be superior candidates for increasing the long-term stability of Li-S batteries.

25 ENERGY STORAGE↗

The Application of Poly(3-hexylthiophene-2,5-diyl) as a Protective Coating for High Rate Cathode Materials

Poly (3-hexylthiophene-2,5-diyl) (P3HT), a conducting polymer studied extensively for its optoelectronic devices, offers a number of advantageous properties when used as a conductive binder for lithium-ion battery cathode materials. By mixing with carbon nanotubes (CNT), P3HTCNT serves as a surface coating for the cathode material LiNi 0.8 Co 0.15 Al 0.05 O 2 (NCA). Oxidation of the P3HT enables high electronic and ionic conductivity to be achieved over the potential range where the NCA is electrochemically active. In addition to the conductivity benefits from electrochemical doping, the P3HT-CNT coating suppresses electrolyte breakdown, thus inhibiting growth of the solid electrolyte interphase (SEI) layer and preventing intergranular cracking in the NCA particles. In conclusion, The use of the P3HT-CNT binder system leads to improved cycling for NCA at high power density with capacities of 80 mAh g -1 obtained after 1000 cycles at 16C, a value that is 4 times greater than what is achieved in the control electrode.

36 MATERIALS SCIENCE↗

Lithium Metal Anodes with Nonaqueous Electrolytes

High-energy rechargeable lithium (Li) metal batteries (LMBs) with Li metal anode (LMA) were first developed in the 1970s, but their practical applications have been hindered by the safety and low-efficiency concerns related to LMA. Recently, a worldwide effort on LMA-based rechargeable LMBs has been revived to replace graphite-based, Li-ion batteries because of the much higher energy density that can be achieved with LMBs. Herein, this review focuses on the recent progress on the stabilization of LMA with nonaqueous electrolytes and reveals the fundamental mechanisms behind this improved stability. Various strategies that can enhance the stability of LMA in practical conditions and perspectives on the future development of LMA are also discussed. These strategies include the use of novel electrolytes such as superconcentrated electrolytes, localized high-concentration electrolytes, and highly fluorinated electrolytes, surface coatings that can form a solid electrolyte interphase with a high interfacial energy and self-healing capabilities, development of “anode-free” Li batteries to minimize the interaction between LMA and electrolyte, approaches to enable operation of LMA in practical conditions, etc. Combination of these strategies ultimately will lead us closer to the large-scale application of LMBs which often is called the “Holy Grail” of energy storage systems.

25 ENERGY STORAGE↗

Unraveling the Heterogeneous but Ordered Microstructure of the Nonionic Deep Eutectic Solvent Formed by Lauric Acid and N -Methylacetamide

The nonionic deep eutectic solvent, formed by lauric acid (LA) and N-methylacetamide (NMA), has been shown to have a heterogeneous molecular structure in which the LA and NMA form nonpolar and polar domains, respectively. Previous vibrational spectroscopy experiments demonstrated that the ability of the LA domains to solvate compounds was limited to long carbon chains, whereas other nonpolar molecules, such as W(CO) 6 , were found to be solvated by both LA and NMA. These experiments were not fully compatible with the previously proposed micelle-like structure of the nonpolar domains of the LA-NMA DES. In this work, the modeling of the DES molecular structure is pursued using classical molecular dynamics simulations. The new classical model reproduces both the SAXS structural factors and the previously experimentally derived interaction map for these LA-NMA DESs. In addition, the simulation also shows that LA-NMA DESs form highly organized LA aggregates that are difficult to disorganize. Further evidence of the correct description provided by the newly derived model is obtained using a moderately polar probe: chloroform-d. Computations using the classical model have a good agreement with the solvation behavior of the probe derived from experiments, in which the location of the probe is found to be mostly within the polar domain of the DES. The computational model also demonstrates that the probe solvation is a consequence of the tightly packed LA structure, which causes nonpolar molecules to be located at the interphase of the DES nonpolar domains.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Nickel-rich Nickel Manganese Cobalt (NMC622) Cathode Lithiation Mechanism and Extended Cycling Effects Using Operando X-ray Absorption Spectroscopy

Ni-rich NMC materials are a particularly promising class of Li-ion cathodes for various applications. LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) offers a unique balance of thermal stability and energy density, thus attracting attention for electric vehicle implementation. However, upon extended cycling, capacity fade is prevalent due to structural degradation, which is a major drawback for layered oxide cathodes. Therefore, exploring the underlying phenomena that drive detrimental structural response can lead to future improvements. For the first time, operando X-ray absorption spectroscopy (XAS) was performed on NMC622 pouch cells at three different stages. An extensive description of the first cycle (de)lithiation mechanisms was achieved through X-ray absorption near-edge structure analyses and extended X-ray absorption fine structure modeling. Transition metal specific electrochemical participation and structural variation revealed that much of the delivered capacity and distortion is a result of Ni redox behavior, while the local structure of Co and Mn are impacted due to their interdependencies. Key mechanistic components were identified, as the local structural variation from redox processes and Ni 3+ Jahn–Teller distortion were decoupled. Further, operando XAS was used to investigate the structural response of NMC622 to extended cycling and was supported by X-ray diffraction, X-ray photoelectron spectroscopy, and electrochemical impedance spectroscopy analyses. In this work, reduced capacity was found in the cell after 100 cycles and is attributed to structural degradation and cathode–electrolyte interphase buildup from repeated Li (de)insertion processes, which limit the electrochemical reversibility of Ni and Co through increased polarization. These results expand the understanding of a Ni-rich NMC material under extended cycling, which is vital to the future design of electrode materials.

25 ENERGY STORAGE↗

Insight into SEI Growth in Li-Ion Batteries using Molecular Dynamics and Accelerated Chemical Reactions

The performance of lithium-ion batteries (LIB) using organic electrolytes strongly depends on the formation of a stable solid electrolyte interphase (SEI) film. Elucidating the dynamic evolution and spatial composition of the SEI can be very useful to study the stability of SEI components and help optimize the formation cycles of LIB. We propose a classical molecular dynamics simulation protocol for predicting the first stages of SEI formation using a reaction method involving the decomposition of EC and LiPF 6 molecules in the electrolyte. We accelerate the formation of SEI components near the anode surface by increasing the probability of reactions, implemented through a geometry matching scheme, followed by a force-field reconfiguration. We observe the formation of gases (C 2 H 4 ), inorganic (Li 2 CO 3 and LiF) and organic (LEDC) components. Finally, this protocol shows promise to be able to evaluate the effects of varying electrolyte compositions and additives on SEI layer structure and composition.

25 ENERGY STORAGE↗

Degradation in Ni-Rich LiNi 1– x – y Mn x Co y O 2 /Graphite Batteries: Impact of Charge Voltage and Ni Content

Ni-rich LiNi 1– x–y Mn x CoyO 2 (NMC) materials are attractive as cathodes for Li-ion batteries due to their high energy density and low Co content. However, these materials may display poor electrochemical reversibility relating to structural and interfacial instabilities. The influence of Ni content and level of delithiation during charge on degradation mechanisms and relevance to electrochemical cycling behavior are probed for LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) and LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathode materials in a full cell configuration under two upper voltage limits (4.1 and 4.3 V). The combined use of dQ/dV analysis of electrochemical voltage profiles, operando XRD, and postcycling scanning electron microscopy (SEM) measurements indicates that a major contributor to capacity fade is the large anisotropic volume change from an H2 $\leftrightarrows$ H3 phase transition and associated mechanical degradation particularly for NMC811. Notably, transition metal dissolution and deposition on the negative electrode are found to correlate with the structural changes occurring in the cathode under high voltage charge. X-ray photoelectron spectroscopy (XPS) analyses of the cycled cathodes reveal a more organic-rich cathode–electrolyte interphase (CEI) when cycling to 4.3 V with lower relative amounts of LiF. Surface reconstruction is not a significant factor under these cycling conditions as determined by soft X-ray absorption spectroscopy (sXAS) analysis. The results emphasize the opportunity to match the electrochemical test parameters with the specific NMC active material to mitigate degradation and extend cycle life.

36 MATERIALS SCIENCE↗

Analysis of Degradation and Electrochemical Behavior of Lithium–Oxygen Batteries under Lean Electrolyte Conditions

Lithium-oxygen batteries have garnered much attention in the past decades due to their high energy density and active material abundancy. Decreasing the electrolyte volume is critical to achieving a high energy density for practical applications. Recent works have demonstrated a serious performance limitation at lower electrolyte fillings. Here, in this work, we study specifically the difference between flooded and lean electrolyte lithium-oxygen batteries by systematically tracing the source of performance degradation. We find that the key contributor to the decrease in performance under lean electrolyte conditions stems from the lithium metal anode rather than the cathode. Solid electrolyte interphase (SEI) compositionally appears to be the same from X-ray photoelectron spectroscopy but the coverage is less uniform, and impedance is much higher under lean electrolyte conditions. Such an effect likely produced the observed poorer cycle performance at 10 μL cm -2 (similar to 28% cathode's pore volume filled) vs 100 μL cm -2 (278% of cathode's pore volume) at a capacity of 1.0 mAh cm -2 (0.1 mAh cm -2 ) using an electrolyte composition of 1 M LiTFSI in TEGDME.

Córdoba, Daniel [Argonne National Laboratory (ANL)↗

Direct Evidence of a Chemical Conversion Mechanism of Atomic-Layer-Deposited TiO 2 Anodes During Lithiation Using LiPF 6 Salt

Titanium dioxide has been identified as a prospective anode material for use in lithium ion batteries. The higher lithiation potential of TiO 2 versus other common anodes is more electrochemically compatible with most organic electrolytes, thus leading to reduced solid electrolyte interphase formation and overall more stable battery systems. However, in this study TiO 2 has exhibited poor cycling stability with common electrolytes containing lithium hexafluorophosphate (LiPF 6 ) salt. Combined electrochemical and spectroscopic analyses have revealed this to be due to the onset of reversible fluorination of the anode and chemical conversion of TiO 2 to TiOF 2 during lithiation. Comparison of electrochemical cycling of atomic-layer-deposited TiO2 anodes using LiPF6 with and without a hydrofluoric acid scavenger, tributylamine, to cycling using a nonfluorinated lithium perchlorate (LiClO 4 ) salt indicates that the in situ formation of hydrofluoric acid in the electrolyte from decomposition of the PF$_{6^–}$ anion alters the lithiation electrochemistry. X-ray photoelectron spectroscopy (XPS) analysis and time-of-flight secondary-ion mass spectrometry (ToF SIMS) depth profiling measurements confirmed the presence of TiF 2 and TiOF surface and bulk phases, respectively, in the electrode upon lithiation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructural Evolution Of Iron Oxyfluoride/Carbon Nanocomposites Upon Electrochemical Cycling

High electrochemical performance iron oxyfluoride conversion electrode undergoes complex electrochemical reaction mechanisms upon cycling. In this work, a combination of selected area electron diffraction (SAED) and scanning transmission electron microscopy/electron energy loss spectroscopy (STEM/EELS) analysis techniques have been used to understand the conversion-reconversion mechanisms of FeO 0.7 F 1.3 /C upon cycling. Considerable changes have been observed with cycling. For the fully delithiated electrodes, the nanometer scale intermixing of amorphous rutile and nanocrystalline rocksalt phases is stable up to 20 cycles; however, upon further cycling the amount of amorphous rutile phase decreased and amount of rocksalt phase increased gradually, implying incomplete reconversion reactions with increasing cycle number. In addition, a progressive growth of solid electrolyte interphase (SEI) layer was observed with cycling, which is mainly composed of LiF. Interestingly, Fe 2+ and Fe nanoparticles were found trapped in the SEI layer with increasing cycle number. Upon cycling, the combined progressive increase in Fe 2+ content and insulating LiF (from SEI and conversion product) give rise to the observed capacity loss.

25 ENERGY STORAGE↗

Effects of High and Low Salt Concentration in Electrolytes at Lithium–Metal Anode Surfaces

The use of high concentration salts in electrolyte solutions of lithium-sulfur (Li-S) batteries has been shown beneficial for mitigating some effects such as polysulfide shuttle and dendrite growth at the Li metal anode. Such complex solutions have structural, dynamical, and reactivity associated issues that need to be analyzed for a better understanding of the reasons behind such beneficial effects. A passivation interfacial layer known as solid-electrolyte interphase (SEI) is generated during battery cycling as a result of electron transfer from the metal anode causing electrolyte decomposition. Here in this work, we investigate using density functional theory and ab initio molecular dynamics simulations the salt decomposition, solvation effects, interactions among intermediate products and other species, and potential components of the SEI layer as a function of chemical nature and concentration of the salt, for lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) and lithium bis(fluorosulfonyl)imide (LiFSI) at 1M and 4M concentrations in dimethoxyethane. It is found that LiTFSI undergoes a less complete reduction and facilitates charge transfer from the anode, whereas LiFSI shows a more complete decomposition forming LiF as one of the main SEI products. In addition, the specific decomposition mechanisms of each salt clearly point to the initial SEI components and the potential main products derived from them. Finally, very complex networks are found among the salt and solvent molecules in their attempt to maximize Li ion solvation that is quantified through the determination of coordination numbers.

25 ENERGY STORAGE↗

The Chemistry of Electrolyte Reduction on Silicon Electrodes Revealed by in Situ ATR-FTIR Spectroscopy

While silicon is the most promising next-generation anode material for lithium-ion batteries (LIBs), silicon electrodes exhibit significant capacity fade with cycling. A common hypothesis is that the capacity loss is due to the solid electrolyte interphase (SEI) forming in the first cycle and becoming destabilized by large cyclic volume changes. A cell for in situ attenuated total reflection-Fourier transform infrared spectroscopy with controllable penetration depth was used to study the chemistry at the electrode–electrolyte interface. The SEI product precursors at the interface were successfully identified and differentiated from free or solvated solvent molecules in the bulk electrolyte. Intriguingly, for the most common electrolyte consisting of ethylene carbonate and diethyl carbonate, ethylene carbonate was found to directly reduce to lithium ethylene dicarbonate on the lithiated silicon surface and diethyl carbonate to selectively reduce to diethyl 2,5-dioxahexane dicarboxylate on the surface of the native silicon-oxide film. In conclusion, understanding this surface dependence of the SEI composition is critical to tuning the silicon electrode surface condition and, ultimately, enhancing the performance of future LIBs.

25 ENERGY STORAGE↗

Fluoroethylene Carbonate Breakdown Mechanisms and Energetics on Two Lithium Silicide Surfaces

Lithium-ion batteries are a leading energy storage technology. One challenge with lithium-ion batteries is the reductive decomposition of electrolyte on the surface, forming a passivating, solid–electrolyte interphase (SEI). The SEI prevents further electrolyte breakdown and consumption, but if not formed properly, may also consume lithium ions and prevent lithium-ion diffusion to the anode. Fluoroethylene carbonate (FEC) is currently one of the best electrolyte additives used to form a more robust SEI on silicon anodes. In this study, we use density functional theory (DFT) to investigate the spontaneous breakdown mechanisms, energies, and charge transfers of FEC on the surface of a silicon anode in a lesser lithiated LiSi and a more lithiated Li 15 Si 4 state. The reductive decomposition of FEC on LiSi and Li 15 Si 4 to F, CO 2 , and CH 2 CHO is energetically most favorable on both surfaces, but F, CO, and OCH 2 CHO can also be formed. The breakdown of FEC via either of the breakdown mechanisms is about 2 times more favorable on the Li 15 Si 4 surface than on the LiSi surface. Lastly, the Bader charge transferred from the anode to the FEC breakdown products is larger when forming F, CO 2 , and CH 2 CHO than when forming F, CO, and OCH 2 CHO and is also larger on the Li 15 Si 4 surface than on the LiSi surface.

25 ENERGY STORAGE↗

The Relationship between Ionic Conductivity and Solvation Structures of Localized High-Concentration Fluorinated Electrolytes for Lithium-Ion Batteries

Localized high concentration electrolyte (LHCE) combines a diluent with high concentration electrolyte (HCE), offering promising properties. The ions, solvent, and diluent interact to form a complex heterogenous liquid structure, where high salt concentration clusters are embedded in diluent. Optimizing LHCE for desired electrolyte properties like high ionic conductivity, low viscosity, effective solid electrolyte interphase (SEI) formability, within the vast chemical and compositional design space requires deeper understanding and theoretical guidance. For this work, we investigated the structures and conductivity of LHCEs based on a fluorinated solvent with two different diluents at varying concentrations. The 2,2,3,3-tetrafluoropropyl trifluoroacetate (TFPTFA) enters the solvation cluster due to its stronger Li-ion interactions, whereas 1,1,2,2-tetrafuoroethyl 2,2,2-trifuoroethyl ether (TFETFE) enters only at extremely high diluent concentrations. The ionic conductivity increases with decreasing diluent concentrations, with a slope change during cluster percolation. Overall, TFETFE demonstrates higher effectiveness than TFPTFA, forming higher local salt concentration clusters, and resulting in higher ionic conductivity.

cluster chemistry↗