Search NASA⌕ Search

SEARCH · Search NASA

Results for “parameter reduction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Application of Analytical Heat Transfer Models of Multi-layered Natural and Engineered Barriers in Potential High-Level Nuclear Waste Repositories - 12435

A combination of transient heat transfer analytical solutions for a finite line source, a series of point sources, and a series of parallel infinite line sources were combined with a quasi-steady-state multi-layered cylindrical solution to simulate the temperature response of a deep geologic radioactive waste repository with multi-layered natural and engineered barriers. This evaluation was performed to provide information to scientists and decision makers to compare candidate geologic media for a repository (crystalline rock [granite], clay, salt, and deep borehole), and to provide input for the future evaluation of the trade-off between pre-emplacement surface storage time, waste package size, and repository footprint. This approach was selected in favor of the finite element solution typically used to analyze the temperature response because it allowed rapid comparison of a large number of alternative disposal options and design configurations. More than 100 combinations of waste form, geologic environment, repository design configuration, and surface storage times were analyzed and compared. The analytical solution approach used to analyze the repository temperature response allowed rapid comparison of a large number of alternative disposal options and design configurations. More than 100 combinations of waste form, geologic environment, repository design configuration, and surface storage times were analyzed and compared. This approach allowed investigation of the sensitivity of the results to combinations of parameters that show that there is much flexibility to be gained in terms of spent fuel management options by varying a few key parameters. This initial analysis used representative design concepts and thermal constraints based on international design concepts, and it also included waste forms representing future fuel cycles with high burnup fuels. Unlike repository designs with large open tunnels and pre-closure ventilation, all of the disposal concepts analyzed in this study used enclosed emplacement modes, where the waste packages were in direct contact with encapsulating engineered or natural materials. The deep borehole repository concept limits the size of the SNF waste packages and may require rod consolidation to fit within the drill casing diameter. A single assembly waste package, assuming rod consolidation, was evaluated in the current analysis. Similar size restrictions apply for the HLW canisters. At this time no thermal constraints have been defined for the deep borehole repository concept. Representative EBS materials and properties were evaluated. However, changes in EBS design concepts and materials can also have significant effects on the maximum waste package surface temperature. Increased thermal conductivity of the buffer layer can be achieved by using an engineered buffer consisting of a mixture of graphite, sand, and bentonite [14]. One of the advantages of the analytical model is that it highlights the sensitivity of the results to the parameters that define the repository layout, including spacing between axial and lateral neighboring waste packages and drifts. It is clear that repository layout adjustments can be made to reduce the calculated peak temperatures. The results also show that significant reductions in required surface storage times can be achieved if higher thermal constraints can be justified Additional studies are planned to evaluate the trade-offs between surface storage times, repository layout parameters, and variations in EBS design concepts. Model validation and uncertainties will also be addressed. It is expected that shorter surface storage times and more optimized repository design configurations may be achieved. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Simulation and Analysis of Technology and Operational Procedures to Reduce the Combined Effects of Emissions and Contrails

The development and evaluation of concepts and technology to support future air traffic management systems require a hierarchy of models ranging from real-time simulations to extensive field evaluations. Air traffic simulation models such as Airspace Concept Evaluation System, Center Tracon Automation System, Future Air traffic management Concept Evaluation Tool and others are used to design air traffic systems balancing the conflicting objectives of maximizing safety, meeting future demands for airports and airspace and increase efficiency of traffic flows in the presence of uncertain weather. The impact of aviation emissions and contrails on climate imposes another constraint on the design of aircraft and aviation operations. The understanding of the complex interaction between physical climate system, the carbon and other greenhouse gas emissions and aviation activity can be improved by the development of integrated assessment models that include emission and climate models together with air traffic simulations. The modeling of aircraft emissions and their interaction with each other to change the concentration levels of different gasses in the atmosphere and the resulting impact of the radiative forcing on the equilibrium of the Earth's atmosphere is complex and requires the use of coupled atmosphere-ocean general circulation models together with three-dimensional models of carbon cycle and chemistry of other non-CO2 greenhouse gases. These models are computationally intensive and unsuitable for studies involving the generation of multiple scenarios. Simple emission and climate models, based on the input-output relations of linear systems, capture the fundamental emission to climate impact behavior by careful selection of key variables and their dynamics. The impact of various greenhouse gases depends on the total concentration, effect per unit change in atmospheric concentration and the spatial distribution of the gas. All these quantities are influenced by the lifetime of the gas. The impact of a greenhouse gas depends on the interval of assessment, which may vary from a few decades to a few centuries. Climate metrics are aimed at providing a common scale to compare different greenhouse gases. If the metrics are to be used as a tool in developing and evaluating aviation operations, they should be transparent and easy to apply. Global Warming Potential and Aggregate Global Temperature Potential are some of the commonly used metrics. This paper integrates a national-level air traffic simulation and optimization capability with simple climate models and carbon cycle models, and climate metrics to assess the impact of aviation on climate. The capability brings together metrics, which are useful in aviation operations together with metrics used in climate studies. The capability can be used to make trade-offs between extra fuel cost and reduction in climate impact. There is considerable uncertainty in our understanding of the radiative forcing associated with emissions and contrails. The parameters in the simulation can be used to evaluate the effect of various uncertainties in emission models and contrails. It can also be used to evaluate the impact of different decision horizons. Alternatively, the optimization results from the simulation can be used as inputs to other tools that monetize global climate impacts like the FAA's Aviation Environmental Portfolio Management Tool for Impacts.

impact of aviation on the environment↗

A Comparative Study of Electrical Double Layer Effects for CO Reduction Reaction Kinetics

Solvation models describe how the interactions between the solutes and solvents affect the reactivity and selectivity in electrochemical processes. In this study, we developed a framework for evaluating the effects of applied potential and electrical double layer on CO reduction (COR), comparing fully explicit, implicit, and hybrid solvation models at the standard hydrogen electrode (SHE) scale. We analyzed all crucial intermediates leading to the production of C 1 and C 2 products and found good agreement across these models. Some notable differences were observed in the implicit description of *C and *CO adsorption at higher overpotentials and overall trends in the adsorption energies within the hybrid model. Using this unified SHE framework, we built comparable microkinetic models for COR kinetics and rates. Despite small differences in thermodynamics, solvation-model-based microkinetic simulations showed good agreement for onset potentials against the benchmark experiment. Only qualitative difference was observed for C 1+ versus hydrogen evolution at high overpotentials for the implicit model. Finally, we constructed a generalized C 2 selectivity map in descriptor space (U SHE , ΔG electrolyte CO ), which highlights the limitations of a copper-based COR catalyst and guides the search for optimal descriptor parameters to maximize C 2 selectivity. In conclusion, these findings demonstrate the importance of considering electrical double layer effects in reduction reactions and offer a useful framework for comparing solvation models and predicting optimal electrochemical conditions for specific applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preserving Lagrangian Structure in Nonlinear Model Reduction with Application to Structural Dynamics

Our work proposes a model-reduction methodology that preserves Lagrangian structure and achieves computational efficiency in the presence of high-order nonlinearities and arbitrary parameter dependence. As such, the resulting reduced-order model retains key properties such as energy conservation and symplectic time-evolution maps. We focus on parameterized simple mechanical systems subjected to Rayleigh damping and external forces, and consider an application to nonlinear structural dynamics. To preserve structure, the method first approximates the system's “Lagrangian ingredients''---the Riemannian metric, the potential-energy function, the dissipation function, and the external force---and subsequently derives reduced-order equations of motion by applying the (forced) Euler--Lagrange equation with these quantities. Moreover, from the algebraic perspective, key contributions include two efficient techniques for approximating parameterized reduced matrices while preserving symmetry and positive definiteness: matrix gappy proper orthogonal decomposition and reduced-basis sparsification. Our results for a parameterized truss-structure problem demonstrate the practical importance of preserving Lagrangian structure and illustrate the proposed method's merits: it reduces computation time while maintaining high accuracy and stability, in contrast to existing nonlinear model-reduction techniques that do not preserve structure.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

A methodology for decay heat characterization in molten salt reactors

Accurate decay heat prediction in molten salt reactors (MSRs) faces dual challenges: complex operational uncertainties and the need for interpretable models compatible with engineering workflows. This work presents a hybrid machine learning and segmented polynomial methodology that addresses both requirements through three key innovations. First, a modular data architecture encodes MSR-specific operational parameters (power density: 1-100 W cm -3 , humidity: 0-0.1 wt %, air ingress: 0-0.1 mol %) with uncertainty-aware temporal discretization spanning 15 orders of magnitude. Second, region-optimized machine learning models achieve 92.3 % root mean square error (RMSE) reduction over conventional polynomials while maintaining physical interpretability through automated piecewise equation generation. Third, dual front-end interfaces accelerate safety analyses — a Jupyter environment enables researchers to explore 10,000+ parameter combinations via interactive widgets, while a Streamlit web application reduces design iteration cycles through production-grade visualization tools. Operational deployment demonstrates prediction times of only a couple hundred milliseconds for 10 4 years decay profiles, enabling real-time optimization of spent fuel container designs.

42 - ENGINEERING↗

Passive SCR for lean gasoline NO X control: Engine-based strategies to minimize fuel penalty associated with catalytic NH 3 generation

Lean gasoline engines offer greater fuel economy than common stoichiometric gasoline engines. However, excess oxygen prevents the use of the current three-way catalyst (TWC) to control nitrogen oxide (NO X ) emissions in lean exhaust. A passive SCR concept, introduced by General Motors Global R&D, makes use of a TWC that is already onboard to generate NH 3 under slightly rich conditions, which is stored on the downstream SCR. The stored NH 3 is then used to reduce NO X emissions when the engine switches to lean operation. In this work, the effect of engine parameters, such as air-fuel equivalence ratio and spark timing, on NH 3 generation over a commercial Pd-only TWC with no dedicated oxygen storage component was evaluated on a 2.0-liter BMW lean burn gasoline direct injection engine. NO X reduction, NH 3 formation, and reductant utilization processes were evaluated, and fuel efficiency was assessed and compared to the stoichiometric engine operation case. We found air-fuel equivalence ratio to be one of the most important parameters in controlling the NH 3 production; however, the rich operation necessary for NH 3 production results in a fuel consumption penalty. The fuel penalty can be minimized by adjusting spark timing to increase rich-phase engine out NO X emissions and, thereby, NH 3 levels. Additionally, higher engine out NO X during engine load increase to simulate acceleration resulted in additional fuel savings. Ultimately, a 10% fuel consumption benefit was achieved with the passive SCR approach by optimizing rich air-fuel equivalence ratio and spark timing while also utilizing acceleration load conditions.

54 ENVIRONMENTAL SCIENCES↗

Next-Cycle Optimal Fuel Control for Cycle-to-Cycle Variability Reduction in EGR-Diluted Combustion

In this simulation study, cycle-to-cycle fuel control was used to reduce CCV by injecting additional fuel in operating conditions with sporadic misfires and partial burns. An optimal control policy was proposed that utilizes 1) a physics-based model that tracks in-cylinder gas composition and 2) a one-step-ahead prediction of the combustion efficiency based on a kernel density estimator. The optimal solution, however, presents a tradeoff between the reduction in combustion CCV and the increase in fuel injection quantity required to stabilize the charge. Such a tradeoff can be ad- just by a single parameter embedded in the cost function.

Maldonado, BryanP. [Oak Ridge National Lab. (ORNL)↗

Investigation of Gallium Nitride Devices in High-Frequency LLC Resonant Converters

Newly emerged gallium nitride (GaN) devices feature ultrafast switching speed and low on-state resistance that potentially provide significant improvements for power converters. Here, this article investigates the benefits of GaN devices in an LLC resonant converter and quantitatively evaluates GaN devices' capabilities to improve converter efficiency. First, the relationship of device and converter design parameters to the device loss is established based on an analytical model of LLC resonant converter operating at the resonance. Due to the low effective output capacitance of GaN devices, the GaN-based design demonstrates about 50% device loss reduction compared with the Si-based design. Second, a new perspective on the extra transformer winding loss due to the asymmetrical primary-side and secondary-side current is proposed. The device and design parameters are tied to the winding loss based on the winding loss model in the finite element analysis (FEA) simulation. Compared with the Si-based design, the winding loss is reduced by 18% in the GaN-based design. Finally, in order to verify the GaN device benefits experimentally, 400- to 12-V, 300-W, 1-MHz GaN-based and Si-based LLC resonant converter prototypes are built and tested. One percent efficiency improvement, which is 24.8% loss reduction, is achieved in the GaN-based converter.

30 DIRECT ENERGY CONVERSION↗

Direct Production of Ferrochrome by Segregation Reduction of Chromite in the Presence of Calcium Chloride

A solid reduction process is described whereby chromite is reduced with the help of calcium chloride to produce ferrochrome alloy powders with high metal recovery. The process involves segregation reduction of chromite using graphite as the reductant and calcium chloride as the segregation catalyst. Experiments were performed in the temperature range of 1200–1400 °C to evaluate the influences of various design parameters using both a thermogravimetric analyzer and an electric tube furnace with continuous off-gas analysis. The reduced products were characterized by scanning electron microscopy, X-ray powder diffraction, synchrotron X-ray absorption spectroscopy, and were subjected to wet chemical analysis. It was concluded that the addition of calcium chloride not only accelerated the carbothermic reduction of chromite but also promoted the formation and growth of individual ferrochrome alloy particles. The alloy formation within chromite particles was minimized, enabling the effective separation of ferrochrome alloy particles from the unwanted gangue without the need for fine grinding. Majority of the calcium chloride remained in a recoverable form, with a small percentage (<10 wt %) consumed by reacting with the siliceous gangue forming wadalite. Pure ferrochrome alloy powders were successfully produced with high metal recovery using elutriating separation.

36 MATERIALS SCIENCE↗

Comparison of structural and magnetic properties of Zn{sub x}Mg{sub 1.5-x}Mn{sub 0.5}FeO{sub 4} and MgAl{sub x}Cr{sub x}Fe{sub 2-2x}O{sub 4} spinel oxides

The spinel oxides Zn{sub x}Mg{sub 1.5-x}Mn{sub 0.5}FeO{sub 4} (x = 0.0 to 0.6) and MgAl{sub x}Cr{sub x}Fe{sub 2-2x}O{sub 4} (x = 0.0 to 0.6) abbreviated as ZMMFO and MACFO respectively, were synthesized by standard ceramic processing. The compositional purity of all the specimens was checked by EDAX technique. The X-ray diffractometry was employed to determine the lattice constants and distribution of cations in the interstitial voids. The initial decrease of cell edge parameter (a) for ZMMFO up to x = 0.2 and thereafter expected rise in the ‘a’ and the initial slower rate of reduction in the lattice constant for MACFO are explained as basic of cation occupancy. The magnetic ordering in both systems is explained by invoking statistical canting models. The compositional variation of magneton number (n{sub B}) for ZMMFO could be very well explained by Localized canting of spin (LCS) model while Random canting of spin (RCS) model was used for MACFO system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

On the role of processing parameters in producing Cu/SiC metal matrix composites via friction stir processing: Investigating microstructure, microhardness, wear and tensile behavior

The main aim of this study is to produce copper reinforced metal matrix composite (MMC) layers using micron sized SiC particles via friction stir processing (FSP) in order to enhance surface mechanical properties. Microstructural evaluation using optical microscopy (OM) and scanning electron microscopy (SEM) indicated that an increase in traverse speed and a decrease in rotational speed cause a reduction in the grain size of stir zone (SZ) for the specimens friction stir processed (FSPed) without SiC particles. With the aim of determining the optimum processing parameters, the effect of traverse speed as the main processing variable on microstructure and microhardness of MMC layers was investigated. Higher traverse speeds resulted in poor dispersion of SiC particles and consequently reduced the microhardness values of MMC layers. It was found that upon addition of SiC particles, wear properties were improved. This behavior was further supported by SEM images of wear surfaces. Results demonstrated that the microcomposite produced by FSP exhibited enhanced wear resistance and higher average friction coefficient in comparison with pure copper. Tensile properties and fracture characteristics of the specimens FSPed with and without SiC particles and pure copper were also evaluated. According to the results, the MMC layer produced by FSP showed lower strength and elongation than pure copper while a remarkable elongation was observed for FSPed specimen without SiC particles. Research Highlights: {yields} Decrease in traverse speed leads to good dispersion of SiC particles in composites. {yields} No distinct TMAZ in side regions of SZ of FSPed specimens with SiC particles. {yields} Microhardness of FSPed specimens with SiC particles shows a remarkable increase. {yields} Reinforcement of Cu with SiC particles improves wear and friction behavior of surface. {yields} A weak bonding in tensile due to probable agglomeration for SiC containing samples.

36 MATERIALS SCIENCE↗

Urinary bisphenol A concentrations are associated with reproductive parameters in young men

Highlights: • Urinary BPA concentrations were analyzed to estimate environmental exposure. • Serum reproductive hormone levels and semen parameters were evaluated. • Negative associations between BPA and sperm counts were found. • Increasing BPA concentrations were associated with altered LH levels. • BPA exposure may adversely impact reproductive function in young men. Bisphenol A (BPA) is a pervasive environmental toxicant with known reproductive effects on sperm parameters and hormone levels. Several observational studies have investigated the associations between BPA exposure and male reproductive function, but findings are inconsistent. The objective of this study was to assess the associations between urinary BPA concentrations and semen quality and reproductive hormone levels in a cross-sectional study with 215 healthy young university students (18–23 years old), investigated between 2010 and 2011 in Southern Spain (Murcia Region). All subjects provided urine, blood serum and semen samples on a single day. Urinary BPA concentrations were measured by dispersive liquid–liquid microextraction and ultra-high performance liquid chromatography with tandem mass spectrometry detection. Semen quality was evaluated by measuring volume, concentration, motility, morphology and total sperm count (TSC). Serum samples were analyzed for reproductive hormones, including follicle-stimulating hormone (FSH), luteinizing hormone (LH), testosterone, inhibin B and estradiol. Relationships between urinary BPA concentrations and semen quality parameters and reproductive hormone levels were examined using linear regression, adjusting for potential confounders and covariates. Ninety-five percent of the men had detectable urinary BPA concentrations with unadjusted median (5th–95th) of 2.8 (0.16–11.5) ng/mL. After adjustment for important covariates, there was a significant positive association between urinary BPA concentrations and serum LH levels (β = 0.07, 95%CI: 0.02;0.12, p-value < 0.01). Urinary BPA concentration was also significantly and inversely associated with sperm concentration (β = − 0.04, 95%CI: − 0.07;− 0.02, p-value < 0.01) and TSC (β = − 0.05, 95%CI: − 0.08;− 0.02, p-value < 0.01). No significant associations were found between BPA and other semen parameters or reproductive hormone levels. Our results support the hypothesis that BPA exposure may be associated with a reduction in Leydig cell capacity (increased LH levels) and decreased sperm counts in young men.

54 ENVIRONMENTAL SCIENCES↗

Thermally induced formation of 2D hexagonal BN nanoplates with tunable characteristics

We have investigated a thermally induced combustion route for preparing 2D hexagonal BN nanoplates from B{sub 2}O{sub 3}+(3+0.5k)Mg+kNH{sub 4}Cl solid system, for k=1–4 interval. Temperature–time profiles recorded by thermocouples indicated the existence of two sequential exothermic processes in the combustion wave leading to the BN nanoplates formation. The resulting BN nanoplates were characterized by X-ray diffraction (XRD), field-emission scanning electron microscopy, PL spectrometry, and Brunauer–Emmett–Teller surface area analysis. It was found that B{sub 2}O{sub 3} was converted into BN completely (by XRD) at 1450–1930 °C within tens of seconds in a single-step synthesis process. The BN prepared at a k=1–4 interval comprised well-shaped nanoplates with an average edge length ranging from 50 nm to several micrometer and thickness from 5 to 100 nm. The specific surface area of BN nanoplates was 13.7 g/m{sup 2} for k=2 and 28.4 m{sup 2}/g for k=4. - Graphical abstract: 2D hexagonal BN nanoplates with an average edge length ranging from 50 nm to several micrometer and thickness from 5 to 100 nm were prepared by combustion of B{sub 2}O{sub 3}+(3+0.5k)Mg+kNH{sub 4}Cl solid mixture in nitrogen atmosphere. - Highlights: • Thermally induced combustion route was developed for synthesizing BN nanoplates from B{sub 2}O{sub 3}. • Mg was used as reductive agent and NH{sub 4}Cl as an effective nitrogen source. • Temperature–time profiles and the combustion parameters were recorded and discussed. • BN with an average edge length from 50 nm to several micrometer and thickness from 5 to 100 nm were prepared. • Our study clarifies the formation mechanism of BN in the combustion wave.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

X-ray diffraction line profile analysis of deformation microstructure in boron modified Ti-6Al-4V alloy

X-ray diffraction line profile analysis (XRDLPA) techniques have been applied to investigate the deformed microstructure of a recently developed boron modified two-phase titanium alloy Ti-6Al-4V. The alloy was hot compressed at 750 deg. C up to 50% height reduction at two different strain rates (10{sup -3} S{sup -1} and 1 S{sup -1}). Microstructural parameters like average domain size, average microstrain within the domain and dislocation density of the two phases were determined using X-ray diffraction line profile analysis. The results indicate an increase in the microstrain and dislocation density for the {alpha}-phase and decrease for the {beta}-phase in the case of boron modified alloys as compared to the normal material. Microstructural modifications viz. the grain refinement and the presence of hard, brittle TiB particles in the case of boron modified alloy are held responsible for the observed difference in the dislocation density. - Research Highlights: {yields} Microstructural examination of hot compressed Ti64 with and without boron addition by XRDLPA. {yields} Smaller average domain size in alpha-phase compared to the corresponding alpha-phase in all cases. {yields} Higher microstrain and dislocation density for {alpha} phase and lower for {beta} phase in case of Ti64+B. {yields} Decrease in domain size while increase in micro-strain and dislocation density with strain rate. {yields} Strain accumulation around TiB particles responsible for high dislocation density in {alpha} phase.

36 MATERIALS SCIENCE↗

Microstructures and microhardness evolutions of melt-spun Al-8Ni-5Nd-4Si alloy

Al-Ni-Nd-Si alloy with nominal composition of Al-8 wt.%Ni-5 wt.%Nd-4 wt.%Si was rapidly solidified by using melt-spinning technique to examine the influence of the cooling rate/conditions on microstructure and mechanical properties. The resulting conventional cast (ingot) and melt-spun ribbons were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy together with energy dispersive spectroscopy, differential scanning calorimetry, differential thermal analysis and Vickers microhardness tester. The ingot alloys consists of four phases namely {alpha}-Al, intermetallic Al{sub 3}Ni, Al{sub 11}Nd{sub 3} and fcc Si. Melt-spun ribbons are completely composed of {alpha}-Al phase. The optical microscopy and scanning electron microscopy results show that the microstructures of rapidly solidified ribbons are clearly different from their ingot alloy. The change in microhardness is discussed based on the microstructural observations. - Highlights: Black-Right-Pointing-Pointer Rapid solidification allows a reduction in grain size, extended solid solution ranges. Black-Right-Pointing-Pointer We observed the matrix lattice parameter increases with increasing wheel speed. Black-Right-Pointing-Pointer Melt-spun ribbons consist of partly amorphous phases embedded in crystalline phases. Black-Right-Pointing-Pointer The solidification rate is high enough to retain most of alloying elements in the Al matrix. Black-Right-Pointing-Pointer The rapid solidification has effect on the phase constitution.

36 MATERIALS SCIENCE↗

Evaluation of Cross Section Uncertainties Using Physical Constraints: Focus on Integral Experiments

Evaluation of neutron-induced reactions between 0 eV and 20 MeV is mainly based on nuclear reaction models with parameters estimated from data assimilation on experiments. Several inconsistencies may appear such as mismatches for the cross sections, larger uncertainties on boundary and no cross-correlations between high energy domain and resonance range. In addition, different evaluations could give good overall behaviour of integral experiments with large compensating effects among them. After a summary of several methods which take into account physical constraints on overlapping energy domains where two nuclear reaction models are needed, we focus on a review of the use of integral experiments as additional physical constraints in the evaluation of parameters and cross section covariances. In particular, we present comparison of traditional multigroup adjustment with data assimilation based on nuclear model parameters by the analysis of JEZEBEL. A general consistency is obtained between these adjustments as well as important reduction of fission cross section uncertainties.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Adapted Cell Design for the Operando X‑Ray Absorption Study of a Structurally Evolving Cu Nanoparticle Ensemble during the CO2 Electroconversion to Multicarbon Products

An improved understanding of the materials that will sustain the future of energy production, storage, and delivery calls for better characterization tools. Operando characterization methods have thus become essential for investigating electrocatalytic materials. Without their resulting insights, the study of highly performing catalysts post-mortem cannot viably facilitate the further development of functional catalysts. Herein, we present an operando electrochemical cell designed for hard X-ray absorption spectroscopy (XAS) and specifically adapted to the study of an electrocatalytically active Cu nanoparticle ensemble. So far, this nanocatalyst has proven to pose quite a challenge to characterize due to its unique structural dynamics. Adopting a design comparable to the H-cell employed for all activity testing, we report the satisfactory translation of the active site formation into an XAS-compatible cell. The simultaneous collection of CO2-derived products during XAS characterization enabled the operando characterization of this CO2-reducing active structure. We report a Cu–Cu coordination number of the first scattering path higher than suggested in our previous studies, highlighting the importance of monitoring metastable nanoelectrocatalysts in operando. This study illustrates important caveats for the electrocatalysis community when considering the application of operando XAS. Our results highlight that the sample size, homogeneity, and stability determine how to interpret the measured signal. Considering these parameters carefully, the operando EXAFS results confirm the exceptional undercoordinated character of the Cu nanoparticle ensemble during CO2 reduction to C2+ products.

Louisia, Sheena↗

Leveraging unlabeled SEM datasets with self-supervised learning for enhanced particle segmentation

Scanning Electron Microscopes (SEMs) are widely used in experimental science laboratories, often requiring cumbersome and repetitive user analysis. Automating SEM image analysis processes is highly desirable to address this challenge. In particle sample analysis, Machine Learning (ML) has emerged as the most effective approach for particle segmentation. However, the time-intensive process of manually annotating thousands of SEM images limits the applicability of supervised learning approaches. Self-Supervised Learning (SSL) offers a promising alternative by enabling knowledge extraction from raw, unlabeled data. This study presents a framework for evaluating SSL techniques in SEM image analysis, focusing on novel methods leveraging the ConvNeXtV2 architecture for particle detection. A dataset comprising 25,000 SEM images is curated to benchmark these proposed SSL methods. The results demonstrate that ConvNeXtV2 models, with varying parameter counts, consistently outperform other techniques in particle detection across different length scales, achieving up to a 34% reduction in relative error compared to established SSL methods. Furthermore, an ablation study explores the relationship between dataset size and SSL performance, providing actionable insights for practitioners regarding model selection and resource efficiency. This research advances the integration of SSL into autonomous analysis pipelines and supports its application in accelerating materials science discovery.

Rettenberger, Luca↗