Search NASA⌕ Search

SEARCH · Search NASA

Results for “support structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,171 records · Page 65

Telescoping Shield for Point-Focusing Solar Concentrators

Telescoping shield normally stowed around solar receiver protects heat engine and supporting structure from overheating when concentrator aimed few degrees away from line to Sun. When extended, shield intercepts off center concentrated solar radiation. Heat spread out over thermally conductive shield and reradiated diffusely not to cause structural damage.

Argoud, M.↗

Launch vehicle aerodynamic data base development comparison with flight data

The aerodynamic development plan for the Space Shuttle integrated vehicle had three major objectives. The first objective was to support the evolution of the basic configuration by establishing aerodynamic impacts to various candidate configurations. The second objective was to provide continuing evaluation of the basic aerodynamic characteristics in order to bring about a mature data base. The third task was development of the element and component aerodynamic characteristics and distributed air loads data to support structural loads analyses. The complexity of the configurations rendered conventional analytic methods of little use and therefore required extensive wind tunnel testing of detailed complex models. However, the ground testing and analyses did not predict the aerodynamic characteristics that were extracted from the Space Shuttle flight test program. Future programs that involve the use of vehicles similar to the Space Shuttle should be concerned with the complex flow fields characteristics of these types of complex configurations.

Hamilton, J. T.↗

Payload missions integration

Highlights of the Payload Missions Integration Contract (PMIC) are summarized. Spacelab Missions no. 1 to 3, OSTA partial payloads, Astro-1 Mission, premission definition, and mission peculiar equipment support structure are addressed.

Mitchell, R. A. K.↗

Deformable subreflector computed by geometric optics

Using a Cassegrainian geometry, the 64-meter antenna with its distorted paraboloidal reflecting surface is forced to produce a uniform phase wavefront by a pathlength-compensating subreflector. First, the computed distortion vectors at the joints or nodes of the main reflector structure supporting the surface panels are best fitted to a paraboloid. Second, the resulting residual distortion errors are used to determine a compensating subreflector surface by ray tracing using geometric optics principles. Third, the totally corrected subreflector surface is defined by the normal directions and distances to the surface of the original symmetric hyperboloid for the purpose of evaluation. Finally, contour maps of distortions of the paraboloid reflector and the compensating subreflector are presented. A field-measured check of the subreflector in focused position as computed by the described methodology is also presented for the antenna position at horizon look with the geometry at 45 degrees elevation.

Katow, M. S.↗

Payload missions integration

Spacelab missions 1 to 3, OSTA partial payloads, Astro-1 mission, premission definition, and mission peculiar equipment support structure are discussed.

Source record↗

Slotted waveguide array antennas for spaceborne SAR applications

Starting with mission definitions and constraints for the NASA proposed Shuttle Active Microwave Experiments (SAMEX) and Free Flying Imaging Radar Experiment (FIREX), Hughes Aircraft Company has compiled and studied the technology available for slotted waveguide planar array antennas suitable for spaceborne SAR application. Antenna performance is derived, and fabrication techniques are discussed. Mission requirements will always lead to an aperture subdivided into waveguide modules, thereby validating a module definition for other mission building blocks. Finally, a specific design is proposed for a SAMEX mission using the modules as RF aperture building blocks, resulting in a (nominal) 15.1 meter by 5.5 meter extensile dual polarized L-, C-, and X-band planar array with an associated extensile graphite/epoxy support structure. Antenna development begin with a fabrication method development study involving a representative portion of an antenna module.

Bostrom, D. E.↗

Flight test of a synthetic aperture radar antenna using STEP

To establish confidence in its overall performance, credible information on the synthetic aperture radar antenna's mechanical properties in orbit must be obtained. However, the antenna's size, design, and operating environment make it difficult to simulate operating conditions under 1-g Earth conditions. The Space Technology Experiments Platform (STEP) offers a timely opportunity to mechanically qualify and characterize the antenna design in a representative environment. The proposed experimental configuration would employ a half-system of the full-scale RADARSAT antenna which would be mounted on the STEP platform in the orbiter cargo bay such that it could be deployed and retracted in orbit (as shown in this figure). The antenna would be subjected to typical environmental exposures while an array of targets and sensors on the antenna support structure and reflecting surface are observed and monitored. In particular, the typical environments would include deployment and retraction, dynamic response to vehicle thruster or base exciter inputs, and thermal soak and transient effects upon entering or exiting Earth eclipse. The proposed experiment would also provide generic information on the properties of large space structures in space and on techniques to obtain the desired information.

Zimcik, D. G.↗

Space Shuttle ice suppression system validation, volume 2

The influence of nozzle size is dramatically illustrated in lab runs. It appears that increasing the size of the nozzle provides better coverage of ogive and mid-region of the external tank. It is interesting to note, however, that for the bottom region of the external tank, coverage seems to decrease with nozzle size. This can be explained if both the assymmetry of the lower set of nozzles and the blockage provided by the Orbiter aft-support structure are taken into account.

Porteiro, J. L. F.↗

Project Explorer: Get Away Special #007

Tentatively scheduled to fly on STS-17 (41G), this get away special aims to demonstrate amateur radio transmissions to global ground stations in the English language. Experiments No. 1, 2, and 3 use the micro-gravity of space flight to study the solidification of lead-antimony and aluminum-copper alloys, the germination of radish seeds, and the growth of potassium-tetracyanoplatinate hydrate crystals in an aqueous solution. Flight results are to be compared with Earth-based data. Experiment No. 4 (the Marshall Amateur Radio Club Experiment - MARCE) features radio transmissions and also provides timing for the start of all other experiments. A microprocessor obtains real-time data from all experiments as well as temperature and pressure measurements within the GAS canister. These data are to be transmitted on previously announced amateur radio frequencies after they are converted into the English language by a digitalker for general reception. The support structure for the G #007 experiments consists of two primary plates and four bumper assemblies.

Henderson, A. J., Jr.↗

The G-002 JUFO-1 payload: Its objectives and results

The JUFO-1 payload basically consists of the mechanical support structure with two shock isolated mounting shelves for the experiment hardware and the service systems. For the envisaged operation time of 72 hours, three 28 VDC batteries, with a total capacity of approx 1,7 kWh are chosen as a partially redundant power source. Data are acquired by a 12 bit PCM system and stored on a tape recorder. Five experiments were conducted: (1) growth of a liquid KH2PO4 salt solution; (2) manufacturing of nickel catalysts; (3) transport mechanisms of heavy metals in water cress shoots; (4) determining the influence of cosmic radiation on four different plant seeds; and (5) use of a microprocessor-sequencer for payload control and sequencing at a low power consumption.

Schmitt, G.↗

An investigation into the probabilistic combination of quasi-static and random accelerations

The development of design load factors are investigated for aerospace and aircraft components and experiment support structures, which are subject to a simultaneous vehicle dynamic vibration and acoustically generated random vibration. The characteristics of the combined acceleration probability density function is determined, and an appropriate percentile level for the combined acceleration is selected. This mechanism is developed and graphical data is provided to select combined accelerations for most popular percentile levels.

Schock, R. W.↗

Parabolic Dish Concentrator (PDC-2) Development

The design of the Parabolic Dish Concentrator (PDC-2) is described. The following five subsystems of the concentrator are discussed: (1) reflective surface subsystem, (2) support structure subsystem, (3) foundation, (4) drive subsystem, and (5) electrical and control subsystem. The status of the PDC-2 development project is assessed.

Rafinejad, D.↗

Solar array Shuttle flight experiment - Hardware development and testing

This paper reports on the fabrication and ground testing of (a) a large area, light-weight, flexible substrate developmental solar array wing that has been built for NASA-MSFC and of (b) the supporting structure and data acquisition system (DAS) which, with the wing, will be flown in the Shuttle as an experiment in 1984. The experiment will verify the dynamics, thermodynamic, and electrical performance predictions of the array wing and will demonstrate the structural capability of the array wing for Orbiter launch and re-entry environments. The experiment hardware verification program was designed to minimize costs and risk of experiment performance degradation while maintaining Shuttle and crew safety. The previous full-scale wing hardware tests included an extension mast water table test and wing testing for random vibration, thermal vacuum, and acoustic environments. The results of these tests were used to define wing design modifications and to scope the test program for the experiment hardware.

Elms, R. V.↗

Advanced passive radiator for spaceborne cryogenic cooling

A novel design to improve the cooling capability of spaceborne cryogenic passive radiators is described. The design is based on the use of lightweight angled radiation shields, low-conductance structural supports, and a separate detachable launch-support system to reduce the parasitic heat leaks from the warm spacecraft to the cold radiator. The effectiveness of this design is demonstrated by thermal-vacuum-chamber experiments which indicate that the angled-radiation-shield assembly has an effective emittance that is an order of magnitude lower than that of the best multilayer insulation used in flight. Performance predictions based on the experiments and analytical model indicate that an advanced passive-radiator design based on this technology would be between 10 and 57% of the size and 10 and 36% of the mass of the best state-of-the-art passive radiators and would make lower temperatures (< 60 K) and larger heat loads practical. The cooling requirements of many new spaceborne instruments could be accommodated by application of this new passive-radiator design.

Steven Bard↗

An investigation into the probabilistic combination of quasi-static and random accelerations

The development of design load factors for aerospace and aircraft components and experiment support structures, which are subject to a simultaneous vehicle dynamic vibration (quasi-static) and acoustically generated random vibration, require the selection of a combination methodology. Typically, the procedure is to define the quasi-static and the random generated response separately, and arithmetically add or root sum square to get combined accelerations. Since the combination of a probabilistic and a deterministic function yield a probabilistic function, a viable alternate approach would be to determine the characteristics of the combined acceleration probability density function and select an appropriate percentile level for the combined acceleration. The following paper develops this mechanism and provides graphical data to select combined accelerations for most popular percentile levels.

Schock, R. W.↗

An AOTV aeroheating and thermal protection study

The aerothermodynamics and thermal protection of aerobraking orbital transfer vehicles are studied with a view toward design methodology and technology requirements. A particular class of geometries is investigated: the ellipsoidally blunted raked-off elliptic cone. Discussed are the influence of various geometrical parameters on the trajectory and the heat flux as well as heating prediction methods ranging from an engineering correlation formula to computational solutions of the Navier-Stokes equations. Finite-rate catalytic thermal protection materials and gas radiation are considered. Estimates of the specific mass of possible thermal protection systems indicate that support structure is a large contributor to the aerobrake mass as compared with the thermal protection insulation itself. Sizing curves are included which enable the designer to estimate the size aerobrake required from heating considerations for different mass vehicles having aerobrakes of several specific masses.

Scott, C. D.↗

Lens-and-Detector Array for Spectrometer

Supporting structure alines lenses and serves as light baffle. Lenses and infrared detectors mounted together in cavities in electroformed plate. Plate and cavities maintain optical alinement while serving as light baffle and aperture stop.

Oberheuser, J.↗

Compact Hydraulic Excavator and Support Unit

Continuous-coal-mining machine maneuverable. Hydraulic coal excavator combined with chock, or roof-support structure, in self-contained unit that moves itself forward as it removes coal from seam. Unlike previous such units, new machine compact enough to be easily maneuverable; even makes small-radius right-angle turns.

Lewis, E. V.↗