Search NASA⌕ Search

SEARCH · Search NASA

Results for “Carbides”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Binder Jet Additive Manufacturing of Silicon Carbide Solar Reactor (CRADA Report)

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

99 GENERAL AND MISCELLANEOUS↗

Binder jet additive manufacturing of silicon carbide solar reactor

Achieving high powder packing density is critical in binder jet additive manufacturing (BJAM), as it directly influences the final part density, mechanical properties, and sintering behavior. Multi-modal powder blends, which combine particles of different sizes, have been explored as a strategy to optimize packing efficiency and minimize defects. In this study, bimodal and trimodal powder blends were obtained by mixing silicon carbide powder in three different sizes. These results show that increased powder density is achievable with bimodal powder blends but is reduced in trimodal blends, and it was found that a 13% increase in the powder tap density was achieved using a bimodal blend of powder. The powder size distribution of the bimodal blend was measured at various stages during binder jet additive manufacturing and, no measurable powder separation occurred even after eight prints. Overall, this study shows limited advantage to trimodal powder blends but good promise for trimodal blends for increasing printed density while maintaining reusability in the binder jet process.

36 MATERIALS SCIENCE↗

Automated Segmentation of Twin Boundaries in TRISO Silicon Carbide Using Deep Neural Networks

Coated particle fuels, such as the tristructural isotropic (TRISO) fuel particle, are essential for high-temperature gas reactor (HTGR) applications due to their efficiency and stability under normal and off-normal conditions. However, widespread commercialization and deployment of this technology for next-generation nuclear applications require robust quality assurance and quality control (QA/QC) methods linking fabrication, properties, and performance. Of the many important metrics for TRISO QA/QC, quantification of the silicon carbide (SiC) microstructure is critical because it correlates with fission product retention during irradiation. Previous work has shown extensive twinning of the SiC microstructure, which strongly affects microstructural metrics; however, twin grain boundaries are not expected play a significant role in fission product diffusion. This report summarizes the initial development, training, and testing of a machine learning image processing algorithm to detect twin grain boundaries in a backscattered electron image, which can be removed so that microstructural metrics can be recalculated for legacy data. Further development and deployment of this model will provide automated, scalable improvement of potential QA/QC methods for the SiC layer of TRISO particles.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Optimization of boron carbide density using direct current sintering for use as sputtering sources at the National Ignition Facility

Several experimental trials were conducted to determine optimal sintering parameters and compositions for purchased boron carbide powder using spark plasma sintering/direct current sintering. Sputtering targets used to create ablators for the National Ignition Facility have been unable to survive post processing procedures suggesting that in-house fabrication may yield better results due to extended control.

36 MATERIALS SCIENCE↗

SILICON CARBIDE THERMOMETRY USING RAMAN SPECTROSCOPY ON IRRADIATED TRISO PARTICLES

Silicon carbide (SiC) passive thermometry has emerged as a promising post-irradiation examination (PIE) technique for estimating irradiation temperature near the end of irradiation. While dilatometry techniques have been traditionally used to analyze prismatic samples after irradiation, Raman spectroscopy has recently been shown to provide comparable results by analyzing Raman-active phonon modes. In this work, Raman spectroscopy has been applied to the SiC layer of cross-sectioned irradiation tristructural isotropic (TRISO) particles from the AGR-5/6/7 experiment to evaluate the feasibility of particle-scale passive thermometry. Two-dimensional Raman mapping was used to measure the position of the SiC longitudinal optical (LO) phonon, which was then converted to an apparent irradiation temperature using a previously established empirical correlation. Particles from AGR-5/6/7 Compacts 2-2-1 and 5-1-3 were selected as their calculated time-averaged, volume-averaged (TAVA) temperatures (828°C and 706°C, respectively) fall within the range of the sensitivity of the experimental approach. The use of SiC thermometry was anticipated to confirm or highlight potential deviations from calculated end-of-life TAVA temperature across compacts. Four particles from Compact 2-2-1 and two particles from Compact 5-1-3 were selected based on 110mAg inventory (either some measurable activity or below the minimum detection limit) which is commonly used as an indicator of in-pile temperature variation of particles within the same compact. Across every particle selected it was determined that the average LO peak position was located around 968 cm-1 to 969 cm-1. Using the previously determined empirical correlation, this corresponds to an irradiation temperature around 950°C to 966°C, which does not align with the reported TAVA temperature values. This discrepancy in apparent irradiation temperatures likely reflects a combination of uncertainties in the calculated particle temperatures and differences in irradiation history between the present specimens and those used to establish the empirical Raman calibration such as neutron flux (damage rate) and SiC microstructure (as fabricated and irradiated).

Vawdrey, Josh [ORNL]↗

Acetic Acid/Propionic Acid Conversion on Metal Doped Molybdenum Carbide Catalyst Beads for Catalytic Hot Gas Filtration

Catalytic hot gas filtration (CHGF) is used to precondition biomass derived fast pyrolysis (FP) vapors by physically removing reactive char and alkali particulates and chemically converting reactive oxygenates to species that are more easily upgraded during subsequent catalytic fast pyrolysis (CFP). Carboxylic acids, such as acetic acid and propionic acid, form during biomass fast pyrolysis and are recalcitrant to downstream catalytic vapor upgrading. This work developed and evaluated catalysts that can convert these acids to more upgradeable ketones at the laboratory scale. Selective catalytic conversion of these reactive oxygenates to more easily upgraded compounds can enhance bio-refinery processing economics through catalyst preservation by reduced coking from acid cracking, by preserving carbon efficiency, and through process intensification by coupling particulate removal with partial upgrading. Two metal-doped molybdenum carbide (Mo2C) supported catalyst beads were synthesized and evaluated and their performance compared with an undoped Mo2C control catalyst beads. For laboratory scale acetic acid conversion, calcium doped Mo2C supported catalyst beads produced the highest yield of acetone at ~96% at 450 °C among undoped and Ca or Ni doped catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Molybdenum Isotopes in Presolar Silicon Carbide Grains: Details of s -process Nucleosynthesis in Parent Stars and Implications for r - and p -processes

We have analyzed molybdenum isotopes, together with strontium and barium isotopes, in 18 presolar silicon carbide grains using the Chicago Instrument for Laser Ionization (CHILI), a resonance ionization mass spectrometer. All observed isotope ratios can be explained by mixtures of pure s-process matter with isotopically solar material. Grain residues were subsequently analyzed for carbon, nitrogen, silicon, and sulfur isotopes, as well as a subset for 26 Al– 26 Mg systematics using the NanoSIMS. These analyses showed that all but one grain are mainstream grains, most probably coming from low-mass asymptotic giant branch (AGB) stars. One grain is of the AB type, for which the origin is still a matter of debate. The high precision of molybdenum isotope measurements with CHILI provides the best estimate to date for s -process molybdenum made in low-mass AGB stars. The average molybdenum isotopic abundances produced by the s -process found in the analyzed mainstream SiC grains are 0% 92 Mo, 0.73% 94 Mo, 13.30% 95 Mo, 36.34% 96 Mo, 9.78% 97 Mo, 39.42% 98 Mo, and 0.43% 100 Mo. Solar molybdenum can be explained as a combination of 45.9% s -process, 30.6% r -process, and 23.5% p -process contributions. Moreover, the observed variability in the individual grain data provides insights into the variability of conditions (neutron density, temperature, and timescale) during s -process nucleosynthesis in the grains' parent stars, as they have subtle effects on specific molybdenum isotope ratios. Lastly, the results indicate that the ratio between p - and r -process molybdenum in presolar SiC from many different types of parent stars is Mo p /Mo r = 0.767, the value inferred for the solar system and consistent with what has been found in bulk samples and leachates of primitive meteorites.

79 ASTRONOMY AND ASTROPHYSICS↗

Raman spectroscopy of neutron irradiated silicon carbide

The effects of neutron irradiation on microstructural evolution and the resultant changes in physical and mechanical properties are of critical importance for the development of silicon carbide (SiC) materials for nuclear applications. This study neutron-irradiated βSiC under a wide range of conditions at temperatures between 235 and 750°C and neutron doses of 0.01–11.8 displacements per atom, and then evaluated the effects on the SiC structure using Raman spectroscopy. The SiC optical phonon lines were shifted to lower wavenumbers by irradiation. Correlations were found among the wavenumber of the longitudinal optical phonon line, irradiation-induced swelling, and irradiation temperature. The peak shift also correlated indirectly with decreasing thermal conductivity of irradiated SiC. The irradiation-induced peak shift is explained by combinations of lattice strain, reduction of the elastic modulus, and other factors including decreasing coherent domain size. These findings bridge irradiation-induced microstructural changes and property changes and illustrate how Raman spectroscopy is a useful tool for nondestructively assessing irradiated SiC materials for nuclear applications.

Koyanagi, T.↗

Metal carbide-graphite composites

Carbon sources effects on niobium carbides, and determination of high temperature flexural strength, flexural creep, and thermal expansion up to 2550 deg C for various materials

Source record↗