Search NASA⌕ Search

SEARCH · Search NASA

Results for “Compression ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Long-Term Isothermal Aging Effects on Carbon Fabric-Reinforced PMR-15 Composites: Compression Strength

A study was conducted to determine the effects of long-term isothermal thermo-oxidative aging on the compressive properties of T-650-35 fabric reinforced PMR-15 composites. The temperatures that were studied were 204, 260, 288, 316, and 343 C. Specimens of different geometries were evaluated. Cut edge-to-surface ratios of 0.03 to 0.89 were fabricated and aged. Aging times extended to a period in excess of 15,000 hours for the lower temperature runs. The unaged and aged specimens were tested in compression in accordance with ASTM D-695. Both thin and thick (plasma) specimens were tested. Three specimens were tested at each time/temperature/geometry condition. The failure modes appeared to be initiated by fiber kinking with longitudinal, interlaminar splitting. In general, it appears that the thermo-oxidative degradation of the compression strength of the composite material may occur by both thermal (time-dependent) and oxidative (weight-loss) mechanisms. Both mechanisms appear to be specimen-thickness dependent.

Bowles, Kenneth J.↗

High-pressure synthesis and thermodynamic stability of PdH 1±ε up to 8 GPa

Palladium hydride alloys are superconductors and hydrogen storage materials. One synthesis route is compression of Pd to high pressure in a hydrogen-rich environment. Here we report the evolution of the unit cell volume of PdH x synthesized by compressing Pd in a pure H 2 medium to pressures from 0.2 to 8 GPa in a diamond anvil cell at room temperature. The volume of the face-centered cubic unit cell changes nonmonotonically with pressure, increasing upon compression from 0.2 to 1 GPa and decreasing upon compression from 1 to 8 GPa. Volume is reversible upon decompression and is independent of whether the sample was heated to 600 K at low pressure (P < 2 GPa). The x-ray diffraction data show no evidence for a phase transition between 0.2 and 8 GPa. The volume maximum at 1 GPa must be caused by progressive hydrogenation from 0 to 1 GPa. Assuming a pressure-volume-composition equation of state derived from previously published data, the [H]:[Pd] ratio in this study increases to a maximum value of x = 1 ± 0.02 at 2 ± 0.5 GPa and remains stable upon further compression to and from 8 GPa. These results add to a mounting body of evidence that PdH 1±ϵ is in thermodynamic equilibrium with pure H 2 at room temperature from 2 GPa to at least 8 GPa. Here, the simplest interpretation is that H atoms occupy all octahedral sites and no tetrahedral sites in face-centered cubic PdH 1.0 .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Numerical observations of dynamic behavior in two-dimensional compressible convection

Using numerical simulations of the anelastic partial differential equations, convective flow in a two-dimensional polytropic atmosphere is investigated. Fixing the aspect ratio at unity and choosing the viscosity as the order parameter, the numerical solutions have indicated a variety of dynamic behavior including (1) oscillatory motion with a period of order the eddy turnover time, (2) quasi-periodic motion with a long period much longer than an eddy turnover time, and (3) at least two branches of solutions in certain regimes.

Ginet, G. P.↗

Determination of structural engineering properties of incoloy 903 and CTX-1 alloys

Tension, notched tension, compression, density, thermal conductivity, and thermal expansion tests were conducted on Incoloy 903 over the temperature range 20 K (-423 F) through 1033 K (1400 F). Fracture toughness tests were performed at room temperature (RT). Creep and rupture tests were conducted at 811 K (1000 F), 922 K (1200 F), and 1033 K (1400 F) for this alloy. Transverse unnotched and notched fatigue tests at R = 0.1 were performed at RT and 922 K (1200 F). For CTX-1 alloy, tension, Charpy V-notch impact, density, thermal conductivity, and thermal expansion tests were conducted over the temperature range 20 K (-423 F) through 1033 K (1400 F). Poisson's ratio was determined at RT, 811 K (1000 F), 922 K (1200 F), and 1033 K (1400 F). Notched tension and compression tests were performed at 20 K (-423 F), RT, and 922 K (1200 F); plane strain fracture toughness tests were conducted at RT, 77 K (-320 F), and 20 K (-423 F). Creep and rupture tests were performed at 811 K (1000 F), 922 K (1200 F), and 1033 K (1400 F); longitudinal unnotched and notched fatigue tests at R = 0.1 were conducted at RT and 922 K (1200 F). Results are presented and discussed.

Ruff, P. E.↗

Effects on inlet technology on cruise speed selection

The impact of cruise speed on technology level for certain aircraft components is examined. External-compression inlets were compared with mixed compression, self starting inlets at cruise Mach numbers of 2.0 and 2.3. Inlet engine combinations that provided the greatest aircraft range were identified. Results show that increased transonic to cruise corrected air flow ratio gives decreased range for missions dominated by supersonic cruise. It is also found important that inlets be designed to minimize spillage drag at subsonic cruise, because of the need for efficient performance for overland operations. The external compression inlet emerged as the probable first choice at Mach 2.0, while the self starting inlet was the probable first choice at Mach 2.3. Airframe propulsion system interference effects were significant, and further study is needed to assess the existing design methods and to develop improvements.

Bangert, L. H.↗

Three-dimensional evaluation of the compression and recovery behavior in a flexible graphite sheet by synchrotron radiation microtomography

The compression and unloading behavior of flexible graphite sheets was investigated using synchrotron radiation microtomography with 1 {mu}m voxel size. The recovery ratio of the flexible graphite sheet was measured accurately by in-situ observation. The three-dimensional strain distribution in the interior of the specimen was obtained using the microstructural tracking method. The inner strain distribution with micrometer scale indicated inhomogeneous deformation. The microstructural tracking analysis revealed that deformation units exist in the flexible graphite sheet. The units seem to deform, affecting the neighboring units with each other. The units had a similar size and shape with compacted exfoliated graphite worms that constitute the flexible graphite sheet. Microscopic deformations during compression and unloading are surely affected by the microstructure of the sheet. Highlights: Black-Right-Pointing-Pointer The compression and recovery behavior was investigated using microtomography. Black-Right-Pointing-Pointer The tracking analysis revealed that deformation units exist in the specimen. Black-Right-Pointing-Pointer Each unit deforms in relation to the neighboring unit.

36 MATERIALS SCIENCE↗

Mechanical response of unidirectional boron/aluminum under combined loading

Three test methods were employed to characterize the response of unidirectional Boron/Aluminum metal matrix composite material under monotonic and cyclic loading conditions, namely, losipescu shear, off-axis tension and compression. The characterization of the elastic and plastic response includes the elastic material properties, yielding and subsequent hardening of the unidirectional composite under different stress ratios in the material principal coordinate system. Yield loci generated for different stress ratios are compared for the three different test methods, taking into account residual stresses and specimen geometry. Subsequently, the yield locus for in-plane shear is compared with the prediction of an analytical, micromechanical model. The influence of the scatter in the experimental data on the predicted yield surface is also analyzed. Lastly, the experimental material strengths in tension and compression are correlated with the maximum stress and the Tsai-Wu failure criterion.

Becker, Wolfgang↗

Compression failure of angle-ply laminates

The present work deals with modes and mechanisms of failure in compression of angle-ply laminates. Experimental results were obtained from 42 angle-ply IM7/8551-7a specimens with a lay-up of ((plus or minus theta)/(plus or minus theta)) sub 6s where theta, the off-axis angle, ranged from 0 degrees to 90 degrees. The results showed four failure modes, these modes being a function of off-axis angle. Failure modes include fiber compression, inplane transverse tension, inplane shear, and inplane transverse compression. Excessive interlaminar shear strain was also considered as an important mode of failure. At low off-axis angles, experimentally observed values were considerably lower than published strengths. It was determined that laminate imperfections in the form of layer waviness could be a major factor in reducing compression strength. Previously developed linear buckling and geometrically nonlinear theories were used, with modifications and enhancements, to examine the influence of layer waviness on compression response. The wavy layer is described by a wave amplitude and a wave length. Linear elastic stress-strain response is assumed. The geometrically nonlinear theory, in conjunction with the maximum stress failure criterion, was used to predict compression failure and failure modes for the angle-ply laminates. A range of wave length and amplitudes were used. It was found that for 0 less than or equal to theta less than or equal to 15 degrees failure was most likely due to fiber compression. For 15 degrees less than theta less than or equal to 35 degrees, failure was most likely due to inplane transverse tension. For 35 degrees less than theta less than or equal to 70 degrees, failure was most likely due to inplane shear. For theta less than 70 degrees, failure was most likely due to inplane transverse compression. The fiber compression and transverse tension failure modes depended more heavily on wave length than on wave amplitude. Thus using a single parameter, such as a ratio of wave amplitude to wave length, to describe waviness in a laminate would be inaccurate. Throughout, results for AS4/3502, studied previously, are included for comparison. At low off-axis angles, the AS4/3502 material system was found to be less sensitive to layer waviness than IM7/8551-7a. Analytical predictions were also obtained for laminates with waviness in only some of the layers. For this type of waviness, laminate compression strength could also be considered a function of which layers in the laminate were wavy, and where those wavy layers were. Overall, the geometrically nonlinear model correlates well with experimental results.

Peel, Larry D.↗

High efficiency stoichiometric internal combustion engine system

A power system including a stoichiometric compression ignition engine in which a roots blower is positioned in the air intake for the engine to control air flow. Air flow is decreased during part power conditions to maintain the air-fuel ratio in the combustion chamber of the engine at stoichiometric, thus enabling the use of inexpensive three-way catalyst to reduce oxides of nitrogen. The roots blower is connected to a motor generator so that when air flow is reduced, electrical energy is stored which is made available either to the roots blower to temporarily increase air flow or to the system electrical load and thus recapture energy that would otherwise be lost in reducing air flow.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Metal versus rare-gas ion irradiation during Ti{sub 1-x}Al{sub x}N film growth by hybrid high power pulsed magnetron/dc magnetron co-sputtering using synchronized pulsed substrate bias

Metastable NaCl-structure Ti{sub 1-x}Al{sub x}N is employed as a model system to probe the effects of metal versus rare-gas ion irradiation during film growth using reactive high-power pulsed magnetron sputtering (HIPIMS) of Al and dc magnetron sputtering of Ti. The alloy film composition is chosen to be x = 0.61, near the kinetic solubility limit at the growth temperature of 500 Degree-Sign C. Three sets of experiments are carried out: a -60 V substrate bias is applied either continuously, in synchronous with the full HIPIMS pulse, or in synchronous only with the metal-rich-plasma portion of the HIPIMS pulse. Alloy films grown under continuous dc bias exhibit a thickness-invariant small-grain, two-phase nanostructure (wurtzite AlN and cubic Ti{sub 1-x}Al{sub x}N) with random orientation, due primarily to intense Ar{sup +} irradiation leading to Ar incorporation (0.2 at. %), high compressive stress (-4.6 GPa), and material loss by resputtering. Synchronizing the bias with the full HIPIMS pulse results in films that exhibit much lower stress levels (-1.8 GPa) with no measureable Ar incorporation, larger grains elongated in the growth direction, a very small volume fraction of wurtzite AlN, and random orientation. By synchronizing the bias with the metal-plasma phase of the HIPIMS pulses, energetic Ar{sup +} ion bombardment is greatly reduced in favor of irradiation predominantly by Al{sup +} ions. The resulting films are single phase with a dense competitive columnar structure, strong 111 orientation, no measureable trapped Ar concentration, and even lower stress (-0.9 GPa). Thus, switching from Ar{sup +} to Al{sup +} bombardment, while maintaining the same integrated incident ion/metal ratio, eliminates phase separation, minimizes renucleation during growth, and reduces the high concentration of residual point defects, which give rise to compressive stress.

36 MATERIALS SCIENCE↗

Residual Stress Measurements in Extreme Environments for Hazardous, Layered Specimens

In nuclear fuel plates of low-enriched U-10Mo (LEU) clad with aluminum by hot isostatic pressing (HIP), post-irradiation stresses arising during reactor shutdown are a major concern for safe reactor operations. Measurement of those residual stresses has not previously been possible because the high radioactivity of the plates requires handling only by remote manipulation in a hot cell. The incremental slitting method for measuring through-thickness stress profiles was modified, and a system for automated, remote operation was built and tested. Experimental modifications consisted of replacing electric-discharge machining (EDM) with a small end mill and strain-gauge measurements with cantilever displacement measurements. The inverse method used to calculate stresses was the pulse-regularization method modified to allow discontinuities across material interfaces. The new system was validated by comparing with conventional slitting on a depleted U-10Mo (DU) fuel plate. The new system was applied to two measurements each on six as-fabricated (pre-irradiation) LEU miniature fuel plates. Variations between the measurements at two locations in the same plate were strongly correlated with measured geometrical heterogeneity in the plate—a tilt in the fuel foil. Compressive stresses in the U-10Mo were shown to increase from 20 to 250 MPa as the ratio of aluminum thickness to U-10Mo thickness increased causing increased constraint during cooling. Faster cooling rates during processing also increased stress magnitudes. The measurements trends agreed with data in the literature from similar plates made with DU, which further validates the method. Because other methods are impractical in a hot cell, the modified slitting method is now poised for the first measurements of post-irradiation stresses.

36 MATERIALS SCIENCE↗

Geomechanical characterization of Rock Valley carbonates

In Rock Valley, Nevada, the USA, past earthquake sequences and shallow faulting in Paleozoic carbonates remain poorly understood. Carbonates are typically more ductile rocks that do not experience large stress drops or fracture coalescence, which contradicts previous observations in the region. As part of the Source Physics Experiment, an effort has been made to experimentally characterize the petrophysical and geomechanical properties of carbonates from Rock Valley. Well core and outcrop samples were used to determine the difference between shallow-buried Tertiary limestones and deeply buried Paleozoic limestones and dolostones. The carbonates possessed porosities between 3 and 9%, with V P and V S in the Tertiary carbonates around 2700 and 1800 m/s, respectively, and 6000 and 3100 m/s, respectively, in the Paleozoic carbonates. Microstructural characterization revealed that the Paleozoic carbonates contained significantly more pre-existing damage and alteration than the Tertiary carbonates, though the deformation varies from localized to diffuse. Unconfined Brazilian tests and triaxial tests with confining pressures between 0 and 50 MPa showed that, although samples all experienced failure, the dolostones typically failed at greater stresses and possessed greater E/ν ratios than the limestones. Furthermore, the Hoek–Brown failure criterion was used to construct failure envelopes with the compressive and tensile failure tests. Velocity, density, and porosity measurements were used to construct a hypothetical velocity-depth profile and compare the results with the theoretical petrophysical measurements. Using brittleness analysis, the likely failure conditions were determined to be low-porosity dolomitic rock for fault nucleation in the Paleozoic basement.

Brittleness↗

Microstructural Characterization and High Strain Rate Plastic Flow Behavior of SMAW Armox500T Steel Joints from Spherical Indentation Experiments

Static indentation and uniaxial compression tests have been conducted on Armox500T steel and its weldments to predict the constraint factor (CF), i.e., ratio of Meyer’s hardness to uniaxial flow stress. Series of dynamic indentation experiments were carried out at impact velocities ranging from 5 to 300 m/s to estimate dynamic hardness as a function of average strain. Subsequently, dynamic indentation (DI) test data and CF determined under static indentation conditions have been used to study the high strain rate plastic flow behavior of Armox500T weldments in comparison with the base metal. It was observed that flow stress for Armox500T and its weldments under dynamic loading conditions (10{sup 4} s{sup −1}) are significantly higher than flow stress measured under static loading conditions (10{sup −3} s{sup −1}). The plastic flow behavior computed from DI is in good agreement with the data evaluated through conventional split Hopkinson pressure bar technique. Further, the study of the microstructure of base metal and weldments by optical microscopy and SEM revealed a considerable variation in the microstructure.

36 MATERIALS SCIENCE↗

Hydrogen-rich syngas production from the steam co-gasification of low-density polyethylene and coal refuse

Gasification provides a promising pathway for transforming waste materials into valuable products, such as fuels and chemicals. Here, this study investigates the steam co-gasification of low-density polyethylene (LDPE) and compressed thickener underflow, representative of coal refuse (CR), in a drop tube reactor. The effects of feed blend ratio (0–100 wt% LDPE) and temperature (800–1000 °C) on syngas composition, tar formation, and process efficiency are examined. The high volatility of LDPE makes it more reactive than CR but also promotes the formation of 2–7 ring aromatic tars. Increasing temperature improves carbon conversion efficiency (CCE), cold gas efficiency (CGE), and syngas yield, although the lower heating value (LHV) of syngas decreases. Hydrogen is the dominant gas product, reaching 59 vol% with the H 2 /CO molar ratio ranging from 2.27 to 4.74. Synergistic effects from alkali and alkali earth metals (AAEMs), particularly K and Ca, in CR ash enhance syngas yield by catalyzing char gasification and tar cracking. Hematite (Fe 2 O 3 ) and ash from sub-bituminous/bituminous coals are explored as tar reforming catalysts. Fe 2 O 3 achieves 100 % tar reforming efficiency, while coal ash, with a lower Fe 2 O 3 content (15 wt%), is less effective at cracking polycyclic aromatic hydrocarbons, particularly naphthalene. These findings demonstrate the flexibility of co-gasification, allowing precise tuning of syngas characteristics for specific downstream applications. Further optimization of waste-derived catalysts could enhance the economic viability of gasification in waste-to-energy processes.

01 COAL, LIGNITE, AND PEAT↗

Effects of positron density and temperature on ion-acoustic solitary waves in a magnetized electron-positron-ion plasma: Oblique propagation

Ion-acoustic (IA) solitary waves are investigated in a magnetized three-component plasma consisting of cold ions, isothermal hot electrons, and positrons. The basic set of fluid equations is reduced to the Korteweg de Vries equation using the standard reductive perturbation (multiple-scale) technique. Theoretical and numerical analyses confirm significant effects of the presence of positrons and the dependence of the electron to positron temperature ratio on the amplitude and the width of IA solitary waves. It is shown that the rarefactive and compressive IA solitary excitations can propagate when the propagation angle {theta} satisfies 0{<=}{theta}<{pi}/2 and {pi}/2<{theta}{<=}{pi}, respectively. Also, it is remarked that the amplitude of the rarefactive and compressive IA solitary excitations is not affected by the magnitude of external magnetic field B{sub 0}, whereas their width depends strictly on B{sub 0}. The numerical analysis has been done based on the typical numerical data from a pulsar magnetosphere.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Strain control of AlGaN/GaN high electron mobility transistor structures on silicon (111) by plasma assisted molecular beam epitaxy

This paper reports on the use of plasma assisted molecular beam epitaxy of AlGaN/GaN-based high electron mobility transistor structures grown on 4 in. Si (111) substrates. In situ measurements of wafer curvature during growth proved to be a very powerful method to analyze the buffer layer's thickness dependent strain. The Ga/N ratio at the beginning of growth of the GaN buffer layer is the critical parameter to control the compressive strain of the entire grown structure. An engineered amount of compressive strain must be designed into the structure to perfectly compensate for the tensile strain caused by differences in the thermal expansion coefficient between the epi-layer and substrate during sample cool down from growth temperatures. A maximum film thickness of 4.2 {mu}m was achieved without the formation of any cracks and a negligible bow of the wafers below 10 {mu}m. Measurement of the as-grown wafers revealed depth profiles of the charge carrier concentration comparable to values achieved on SiC substrates and mobility values of the two dimensional electron gas in the range 1230 to 1350 cm{sup 2}/Vs at a charge carrier concentration of 6.5-7 10{sup 12}/cm{sup 2}. First results on processed wafers with 2 {mu}m thick buffer layer indicate very promising results with a resistance of the buffer, measured on 200 {mu}m long contacts with 15 {mu}m pitch, in the range of R > 10{sup 9}{Omega} at 100 V and breakdown voltages up to 550 V.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ion-acoustic cnoidal waves in a quantum plasma

Nonlinear ion-acoustic cnoidal wave structures are studied in an unmagnetized quantum plasma. Using the reductive perturbation method, a Korteweg-de Vries equation is derived for appropriate boundary conditions and nonlinear periodic wave solutions are obtained. The corresponding analytical solution and numerical plots of the ion-acoustic cnoidal waves and solitons in the phase plane are presented using the Sagdeev pseudo-potential approach. The variations in the nonlinear potential of the ion-acoustic cnoidal waves are studied at different values of quantum parameter H{sub e} which is the ratio of electron plasmon energy to electron Fermi energy defined for degenerate electrons. It is found that both compressive and rarefactive ion-acoustic cnoidal wave structures are formed depending on the value of the quantum parameter. The dependence of the wavelength and frequency on nonlinear wave amplitude is also presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

MHD plasma stabilization in a chain of axisymmetric adiabatic open mirror cells

Conditions for convective plasma instability in a chain of axisymmetric adiabatic mirror cells with different signs of magnetic field curvature are analyzed. The boundaries of the region that can be occupied by a stable hollow plasma in a system of two connected cells-a nonparaxial simple mirror cell and a semicusp-are determined, as well as the interval of allowed values of the ratio between the pressures in the cells. Because of the large magnetic field curvature in the component cells, the safety factor that is achieved at both-external and internal-plasma boundaries in accordance with the average min-B principle can be high. It is assumed that the unperturbed pressure in each cell is almost isotropic, in which case the mirror ratio should necessarily be large. A key role in the stability of the plasma is played by its compressibility. A comparison is made between the conditions for complete plasma stabilization against arbitrary perturbations and the conditions for stability of individual cells against the global mode. The stability of the cells against the global mode is sufficient, but not necessary, for stabilizing the chain. The analysis is done by using orthogonal coordinates associated with the unperturbed magnetic field (flux variables). Numerical simulations were carried out for nonparaxial cells from a certain three-parameter family.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗