Search NASA⌕ Search

SEARCH · Search NASA

Results for “Computer codes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Design for cyclic loading endurance of composites

The present paper describes the application of the computer code IPACS (Integrated Probabilistic Assessment of Composite Structures) to air craft wing type structures. The code performs a complete probabilistic structural analysis for composites taking into account the uncertainties in geometry, boundary conditions, material properties, laminate lay-ups and loads. Results of the analysis are presented in terms of cumulative distribution functions (CDF) and probability density function (PDF) of life of a wing type composite structure under different hygrothermal environments subjected to random pressure. The sensitivity of fatigue life to a number of critical structural/material variables is also computed from the analysis.

Shiao, Michael C.↗
NASA NTRS1989

Influence of wing geometry on leading-edge vortices and vortex-induced aerodynamics at supersonic speeds

An assessment of the influence of wing geometry on wing leading-edge vortex flows at supersonic speeds is discussed as well as the applicability of various aerodynamic codes for predicting these results. A series of delta-wing wind-tunnel models were tested in the NASA Langley Research Center Unitary Plan Wind Tunnel over a Mach number range from 1.6 to 4.6. The data show that wing airfoil has a significant impact on the localized loading on the wing. The experimental data for the flat wings were compared with results from full-potential, Euler, and Parabolized Navier-Stokes (PNS) computer codes. The theoretical evaluation showed that the full-potential analysis predicted accurate results for the attached-flow (alpha = 0 deg) conditions and that the Euler and PNS analyses made reasonable predictions for both attached and separated flow conditions.

Wood, Richard M.↗
NASA NTRS1993

Design for cyclic loading endurance of composites

The application of the computer code IPACS (Integrated Probabilistic Assessment of Composite Structures) to aircraft wing type structures is described. The code performs a complete probabilistic analysis for composites taking into account the uncertainties in geometry, boundary conditions, material properties, laminate lay-ups, and loads. Results of the analysis are presented in terms of cumulative distribution functions (CDF) and probability density function (PDF) of the fatigue life of a wing type composite structure under different hygrothermal environments subjected to the random pressure. The sensitivity of the fatigue life to a number of critical structural/material variables is also computed from the analysis.

Shiao, Michael C.↗
NASA NTRS1998

Simulation of Conformal Spiral Slot Antennas on Composite Platforms

During the course of the grant, we wrote and distributed about 12 reports and an equal number of journal papers supported fully or in part by this grant. The list of reports (title & abstract) and papers are given in Appendices A and B. This grant has indeed been instrumental in developing a robust hybrid finite element method for the analysis of complex broadband antennas on doubly curved platforms. Previous to the grant, our capability was limited to simple printed patch antennas on mostly planar platforms. More specifically: (1) mixed element formulations were developed and new edge-based prisms were introduced; (2) these elements were important in permitting flexibility in geometry gridding for most antennas of interest; (3) new perfectly matched absorbers were introduced for mesh truncations associated with highly curved surfaces; (4) fast integral algorithms were introduced for boundary integral truncations reducing CPU time from O(N-2) down to O(N-1.5) or less; (5) frequency extrapolation schemes were developed for efficient broadband performance evaluations. This activity has been successfully continued by NASA researchers; (6) computer codes were developed and extensively tested for several broadband configurations. These include FEMA-CYL, FEMA-PRISM and FEMA-TETRA written by L. Kempel, T. Ozdemir and J. Gong, respectively; (7) a new infinite balun feed was designed nearly constant impedance over the 800-3000 MHz operational band; (8) a complete slot spiral antenna was developed, fabricated and tested at NASA Langley. This new design is a culmination of the projects goals and integrates the computational and experimental efforts. this antenna design resulted in a U.S. patent and was revised three times to achieve the desired bandwidth and gain requirements from 800-3000 MHz.

Volakis, J. L.↗
NASA NTRS1984

Three-dimensional transonic potential flow about complex 3-dimensional configurations

An analysis has been developed and a computer code written to predict three-dimensional subsonic or transonic potential flow fields about lifting or nonlifting configurations. Possible condfigurations include inlets, nacelles, nacelles with ground planes, S-ducts, turboprop nacelles, wings, and wing-pylon-nacelle combinations. The solution of the full partial differential equation for compressible potential flow written in terms of a velocity potential is obtained using finite differences, line relaxation, and multigrid. The analysis uses either a cylindrical or Cartesian coordinate system. The computational mesh is not body fitted. The analysis has been programmed in FORTRAN for both the CDC CYBER 203 and the CRAY-1 computers. Comparisons of computed results with experimental measurement are presented. Descriptions of the program input and output formats are included.

Reyhner, T. A.↗
NASA NTRS2016

Tool for Generation of MAC/GMC Representative Unit Cell for CMC/PMC Analysis

This document describes a recently developed analysis tool that enhances the resident capabilities of the Micromechanics Analysis Code with the Generalized Method of Cells (MAC/GMC) 4.0. This tool is especially useful in analyzing ceramic matrix composites (CMCs), where higher fidelity with improved accuracy of local response is needed. The tool, however, can be used for analyzing polymer matrix composites (PMCs) as well. MAC/GMC 4.0 is a composite material and laminate analysis software developed at NASA Glenn Research Center. The software package has been built around the concept of the generalized method of cells (GMC). The computer code is developed with a user friendly framework, along with a library of local inelastic, damage, and failure models. Further, application of simulated thermomechanical loading, generation of output results, and selection of architectures to represent the composite material have been automated to increase the user friendliness, as well as to make it more robust in terms of input preparation and code execution. Finally, classical lamination theory has been implemented within the software, wherein GMC is used to model the composite material response of each ply. Thus, the full range of GMC composite material capabilities is available for analysis of arbitrary laminate configurations as well. The primary focus of the current effort is to provide a graphical user interface (GUI) capability that generates a number of different user-defined repeating unit cells (RUCs). In addition, the code has provisions for generation of a MAC/GMC-compatible input text file that can be merged with any MAC/GMC input file tailored to analyze composite materials. Although the primary intention was to address the three different constituents and phases that are usually present in CMCs-namely, fibers, matrix, and interphase-it can be easily modified to address two-phase polymer matrix composite (PMC) materials where an interphase is absent. Currently, the tool capability includes generation of RUCs for square packing, hexagonal packing, and random fiber packing as well as RUCs based on actual composite micrographs. All these options have the fibers modeled as having a circular cross-sectional area. In addition, a simplified version of RUC is provided where the fibers are treated as having a square cross section and are distributed randomly. This RUC facilitates a speedy analysis using the higher fidelity version of GMC known as HFGMC. The first four mentioned options above support uniform subcell discretization. The last one has variable subcell sizes due to the primary intention of keeping the RUC size to a minimum to gain the speed ups using the higher fidelity version of MAC. The code is implemented within the MATLAB (The Mathworks, Inc., Natick, MA) developmental framework; however, a standalone application that does not need a priori MATLAB installation is also created with the aid of the MATLAB compiler.

Materials Engineering↗
DOE OSTI2025

Fluid modeling of low-temperature plasmas

Fluid models are essential for understanding and predicting low-temperature plasma (LTP) behavior in various scientific and industrial settings. This paper provides an introductory tutorial on fluid modeling of LTPs, covering model formulation, implementation, and computational simulations. The tutorial focuses on five main components of the formulation of LTP fluid models: fluid flow, energy, chemistry, electromagnetism, and material properties, as well as in essential aspects of model implementations, including multiscale phenomena, multiphysics coupling, and numerical convergence. Designed for students and early-career researchers, this work offers a practical foundation for developing and using fluid models, from in-house computational codes to commercial software, bridging fundamental theory with real-world applications.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1987

Effect of a localized minimum in equatorial field strength on resistive tearing instability in the geomagnetotail

A two-dimensional, resistive-MHD computer code is used to investigate the spontaneous reconnection of magnetotaillike configurations. The initial conditions adopted in the simulations are of two types: (1) in which the equatorial normal magnetic field component B(ze) declines monotonically down the tail, and (2) in which B(ze) exhibits a deep minimum in the near-earth plasma sheet. To represent the case where the earthward convection stops before the X line forms, zero-flow boundary conditions are imposed at the edges of the computational box. The initial configurations are in equilibrium and table within ideal MHD. The dynamic evolution of the system starts after the resistivity is turned on. The main results of these simulations basically support the neutral-line model of substorms and confirm Birn's (1980) computer studies. Spontaneous formation of an X-type neutral point and a single O-type plasmoid with strong tailward flow on the tailward side of the X point is found. The time interval from the turning on of the resistivity to the formation of a plasmoid is much shorter in the case where there is an initial deep minimum. A simple analytic calculation is also carried out to demonstrate why the configuration with a deep minimum is more susceptible to the development of the neutral point.

Hau, L.-N.↗
NASA NTRS1997

Pre-Flight Dark Forward Electrical Testing of the Mir Cooperative Solar Array

The Mir Cooperative Solar Array (MCSA) was developed jointly by the United States (US) and Russia to provide approximately 6 kW of photovoltaic power to the Russian space station Mir. After final assembly in Russia, the MCSA was shipped to the NASA Kennedy Space Center (KSC) in the summer of 1995 and launched to Mir in November 1995. Program managers were concerned of the potential for MCSA damage during the transatlantic shipment and the associated handling operations. To address this concern, NASA Lewis Research Center (LERC) developed an innovative dark-forward electrical test program to assess the gross electrical condition of each generator following shipment from Russia. The use of dark test techniques, which allow the array to remain in the stowed configuration, greatly simplifies the checkout of large area solar arrays. MCSA dark electrical testing was successfully performed at KSC in July 1995 following transatlantic shipment. Data from this testing enabled engineers to quantify the effects of potential MCSA physical damage that would degrade on-orbit electrical performance. In this paper, an overview of the principles and heritage of photovoltaic array dark testing is given. The specific MCSA dark test program is also described including the hardware, software, testing procedures and test results. The current-voltage (4) response of both solar cell circuitry and by-pass diode circuitry was obtained. To guide the development of dark test hardware, software and procedures, a dedicated FORTRAN computer code was developed to predict the dark 4 responses of generators with a variety of feasible damage modes. By comparing the actual test data with the predictions, the physical condition of the generator could be inferred. Based on this data analysis, no electrical short-circuits or open-circuits were detected. This suggested the MCSA did not sustain physical damage that affected electrical performance during handling and shipment from Russia to the US. Good agreement between the test data and computational predictions indicated MCSA electrical performance was amenable to accurate analysis and was well understood.

Kerslake, Thomas W.↗
NASA NTRS1975

Computation of nonequilibrium three-dimensional inviscid flow over blunt-nosed bodies flying at supersonic speeds

A computer code based on the method of characteristics is described and applied to the study of two- and three-dimensional chemical nonequilibrium flow over sharp and blunt-nosed bodies. Nonequilibrium flow over a wedge is used to show the approach to equilibrium flow, and to demonstrate the nature of the reaction zone behind the bow shock wave. The structure and development of a blunt-body entropy layer in nonequilibrium flow is examined for a blunt cone at zero incidence. Three-dimensional computations for the space shuttle body at 30 deg angle of attack are presented. A nondimensional scaling parameter, the Damkoehler number, which is the ratio of flow time to chemical reaction time, is calculated and its significance discussed.

Rakich, J. V.↗
NASA NTRS1994

Non-dipolar magnetic field models and patterns of radio emission: Uranus and Neptune compared

The magnetic field geometries of Uranus and Neptune are superficially similar, and are similarly unlike those of other planets: the field strengths are similar, and they contain extraordinarily large non-dipolar components. As a corollary, the best dipolar field models of each of the two planets comprises a dipole that is considerably offset from the planetary center and tilted away from the rotational axis. However, in other respects the best field models of the two planets are quite different. Uranus has a quadrupole model in which all the terms are well determined and in which none of the higher order terms is determined. To represent the magnetometer data acquired during Voyager's Neptune encounter requires a model of order 8 (instead of Uranus' order 2), yet many of the coefficients are poorly determined. A second model, an octupole model comprising the terms up to order three of the order 8 model, has been suggested by the magnetometer team as being useful; its use, however, is limited only to the region outside of about 2R(exp N), whereas planetary radio emissions have their sources well inside this surface. Computer code has been written that permits an analysis of the detailed motion of low energy charged particles moving in general planetary magnetic fields. At Uranus, this code reveals the existence of an isolated region of the inner magnetosphere above the day side in which particles may be trapped, separate from the more general magnetospheric trapping. An examination of the so-call ordinary mode uranian radio emissions leads us to believe that these emissions are in fact extraordinary mode emissions coming from particles trapped in this isolated region. A similar attempt to discover trapping regions at Neptune has proved, unfortunately, to be impossible. This arises from three factors: (1) the computation needed to track particles in an eighth order field is more than an order of magnitude greater than that needed to perform a similar calculation in a quadrupole field, and is beyond the capacity of workstation-class computers; (2) the octupole field model is known to be in error by too large an ammount for it, or any similarly truncated version of the eighth order model, to produce trustworthy results; (3) the eighth order model can, in effect, be infinitely varied without affecting the field strength along the spacecraft trajectory.

Evans, D. R.↗
NASA NTRS1990

Computing interference flows past cylinder-fin-sting assembly in and near a cavity

The internal carriage of stores by the military aircraft is an option, particularly at high speeds, for a possible reduction in the aerodynamic drag and in the radar observability. Trade studies of this option, which include the safe separation of stores from their bays and aerodynamic complications of a cavity flow, require studying the aircraft and the stores together. With this motivation, the computer code, VISCC, is developed to solve the three-dimensional, Reynolds-averaged, unsteady, compressible, and complete Navier-Stokes equations. The store considered here for simulation is a missile configuration with four tail fins and an L-shaped offset sting. The missile is placed first directly above the opening of a rectangular box cavity, then submerged completely inside the cavity. The freestream Mach and the unit Reynolds numbers are 2.75 and 2.97 million per foot, respectively. The results of the time-accurate computations depict these complex flows and help understanding the interference effects. The time-averaged surface pressures compare favorably with the available wind tunnel data.

Baysal, O.↗
NASA NTRS1992

ANOPP/VMS HSCT ground contour system

This viewgraph shows the integration of the Visual Motion Simulator with ANOPP. ANOPP is an acronym for the Aircraft NOise Prediction Program. It is a computer code consisting of dedicated noise prediction modules for jet, propeller, and rotor powered aircraft along with flight support and noise propagation modules, all executed under the control of an executive system. The Visual Motion Simulator (VMS) is a ground based motion simulator with six degrees of freedom. The transport-type cockpit is equipped with conventional flight and engine-thrust controls and with flight instrument displays. Control forces on the wheel, column, and rudder pedals are provided by a hydraulic system coupled with an analog computer. The simulator provides variable-feel characteristics of stiffness, damping, coulomb friction, breakout forces, and inertia. The VMS provides a wide range of realistic flight trajectories necessary for computing accurate ground contours. The NASA VMS will be discussed in detail later in this presentation. An equally important part of the system for both ANOPP and VMS is the engine performance. This will also be discussed in the presentation.

Rawls, John, Jr.↗
NASA NTRS2010

Development of a Aerothermoelastic-Acoustics Simulation Capability of Flight Vehicles

A novel numerical, finite element based analysis methodology is presented in this paper suitable for accurate and efficient simulation of practical, complex flight vehicles. An associated computer code, developed in this connection, is also described in some detail. Thermal effects of high speed flow obtained from a heat conduction analysis are incorporated in the modal analysis which in turn affects the unsteady flow arising out of interaction of elastic structures with the air. Numerical examples pertaining to representative problems are given in much detail testifying to the efficacy of the advocated techniques. This is a unique implementation of temperature effects in a finite element CFD based multidisciplinary simulation analysis capability involving large scale computations.

Gupta, K. K.↗
NASA NTRS1988

An explicit Runge-Kutta method for 3D turbulent incompressible flows

A computer code has been developed to solve for the steady-state solution of the 3D incompressible Reynolds-averaged Navier-Stokes equations. The approach is based on the cell-center, central-difference, finite-volume formulation and an explicit one-step, multistage Runge-Kutta time-stepping scheme. The Baldwin-Lomax turbulence model is used. Techniques to accelerate the rate of convergence to a steady-state solution include the preconditioned method, the local time stepping, and the implicit residual smoothing. Improvements in computational efficiency have been demonstrated in several areas. This numerical procedure has been used to simulate the turbulent horseshoe vortex flow around an airfoil/flat-plate juncture.

Sung, Chao-Ho↗
NASA NTRS1991

Least-squares/parabolized Navier-Stokes procedure for optimizing hypersonic wind tunnel nozzles

A new procedure is demonstrated for optimizing hypersonic wind-tunnel-nozzle contours. The procedure couples a CFD computer code to an optimization algorithm, and is applied to both conical and contoured hypersonic nozzles for the purpose of determining an optimal set of parameters to describe the surface geometry. A design-objective function is specified based on the deviation from the desired test-section flow-field conditions. The objective function is minimized by optimizing the parameters used to describe the nozzle contour based on the solution to a nonlinear least-squares problem. The effect of the changes in the nozzle wall parameters are evaluated by computing the nozzle flow using the parabolized Navier-Stokes equations. The advantage of the new procedure is that it directly takes into account the displacement effect of the boundary layer on the wall contour. The new procedure provides a method for optimizing hypersonic nozzles of high Mach numbers which have been designed by classical procedures, but are shown to produce poor flow quality due to the large boundary layers present in the test section. The procedure is demonstrated by finding the optimum design parameters for a Mach 10 conical nozzle and a Mach 6 and a Mach 15 contoured nozzle.

Korte, John J.↗
NASA NTRS1972

Large deflection elastic-plastic dynamic response of stiffened shells of revolution

The formulation and check out porblems for a computer code DYNAPLAS, which analyzes the large deflection elastic-plastic dynamic response of stiffened shells of revolution, are presented. The formulation for special discretization is by the finite element method with finite differences being used for the evaluation of the pseudo forces due to material and geometric nonlinearities. Time integration is by the Houbolt method. The stiffeners may be due to concentrated or distributed eccentric rings and spring supports at arbitrary angles around the circumference of the elements. Check out porblems include the comparison of solutions from DYNAPLAS with experimental and other computer solutions for rings, conical and cylindrical shells and a curved panel. A hypothetical submarine including stiffeners and missile tube is studied under a combination of hydrostatic and dynamically applied asymmetrical pressure loadings.

Stricklin, J. A.↗
NASA NTRS1986

Comparison of analytical and experimental performance of a wind-tunnel diffuser section

Wind tunnel diffuser performance is evaluated by comparing experimental data with analytical results predicted by an one-dimensional integration procedure with skin friction coefficient, a two-dimensional interactive boundary layer procedure for analyzing conical diffusers, and a two-dimensional, integral, compressible laminar and turbulent boundary layer code. Pressure, temperature, and velocity data for a 3.25 deg equivalent cone half-angle diffuser (37.3 in., 94.742 cm outlet diameter) was obtained from the one-tenth scale Altitude Wind Tunnel modeling program at the NASA Lewis Research Center. The comparison is performed at Mach numbers of 0.162 (Re = 3.097x19(6)), 0.326 (Re = 6.2737x19(6)), and 0.363 (Re = 7.0129x10(6)). The Reynolds numbers are all based on an inlet diffuser diameter of 32.4 in., 82.296 cm, and reasonable quantitative agreement was obtained between the experimental data and computational codes.

Shyne, R. J.↗