Search NASA⌕ Search

SEARCH · Search NASA

Results for “Control Model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Modelling issues of the SCOLE control problem

Nonlinear and linear equations of motions were derived. The preliminary investigation consisted of model beam as truss structure, effects of truss structure on control design, and effects of reflector offset on control design. It was concluded that the offset of the reflector c.g. from the beam reflector attach point is dynamically significant. Also, truss effects may also significantly effect the performance of the controller if ignored. If the truss is included in the modeling of the NASA/SCOLE configuration, a practically implementable scheme is available to reduce the model order.

Hotz, A. F.↗

Formal specification and verification of a fault-masking and transient-recovery model for digital flight-control systems

The formal specification and mechanically checked verification for a model of fault-masking and transient-recovery among the replicated computers of digital flight-control systems are presented. The verification establishes, subject to certain carefully stated assumptions, that faults among the component computers are masked so that commands sent to the actuators are the same as those that would be sent by a single computer that suffers no failures.

Rushby, John↗

Control of flexible structures and the research community

The Control of Flexible Structures II (CPFS) program is a complex and ambitious undertaking which addresses several critical technology areas. Among them are modeling, structural dynamics, control, and ground testing issues, which are also applicable to other large space structure programs being contemplated. This effort requires early integration of controls and structural dynamic considerations. Several technological advances must be achieved in the areas of system modeling, control synthesis and methodology, sensor/actuator development, and ground testing techniques for system evaluation and on-orbit performance prediction and verification. This program offers an opportunity for the integration of several disciplines to produce technology advances which will benefit many future programs.

Keckler, Claude R.↗

Robustness In Suppressing Vibrations With Adaptive Control

Report describes theoretical and experimental study of robustness of adaptive model-reference control scheme designed to suppress vibrations in large, flexible structure. Model can be mathematical model or collection of models approximating dynamics of structure, vibration sensors, and vibration-suppressing actuators.

Ih, Che-Hang C.↗

Lift, Drag, and Elevator Hinge Moments of Handley Page Control Surfaces

This report combines the wind tunnel results of tests on four control surface models made in the two wind tunnels of the Navy Aerodynamic Laboratory, Washington Navy Yard, during the years of 1922 and 1924, and submitted for publication to the National Advisory Committee for Aeronautics May 7, 1927. The purpose of the tests was to compare, first, the lifts and the aerodynamic efficiencies of the control surfaces from which their relative effectiveness as tail planes could be determined; then the elevator hinge moments upon which their relative ease of operation depended. The lift and drag forces on the control surface models were obtained for various stabilizer angles and elevator settings in the 8 by 8 foot tunnel by the writer in 1922; the corresponding hinge moments were found in the 4 by 4 foot tunnel by Mr. R. M. Bear in 1924. (author)

Smith, R H↗

NASA Tech Briefs, May 2007

Topics include: Noise-Canceling Helmet Audio System; Program Analyzes Spacecraft/Ground Radio Links; Two-Way Communication Using RFID Equipment and Techniques; Six-Message Electromechanical Display System; Scanning Terahertz Heterodyne Imaging Systems; Master Clock and Time-Signal-Distribution System; Synchronous Phase-Resolving Flash Range Imaging; Integrated Radial Probe Transition From MMIC to Waveguide; Bar-Code System for a Microbiological Laboratory; MMIC Amplifier Produces Gain of 10 dB at 235 GHz; Mapping Nearby Terrain in 3D by Use of a Grid of Laser Spots; Digital Beam Deflectors Based Partly on Liquid Crystals; Narrow-Band WGM Optical Filters With Tunable FSRs; Better Finite-Element Analysis of Composite Shell Structures; Computing Spacecraft-Pointing Vectors for Limb Tracking; Enhanced Master Controller Unit Tester; Rover Graphical Simulator; Increasing Durability of Flame-Sprayed Strain Gauges; Multifunctional, High-Temperature Nanocomposites; Multilayer Impregnated Fibrous Thermal Insulation Tiles; Radiation-Shielding Polymer/Soil Composites; Film/Adhesive Processing Module for Fiber-Placement Processing of Composites; Fabrication of Submillimeter Axisymmetric Optical Components; Electrochemical Disposal of Hydrazines in Water; Statistical Model of Evaporating Multicomponent Fuel Drops; Resistively Heated SiC Nozzle for Generating Molecular Beams; Compact Packaging of Photonic Millimeter-Wave Receiver; Diffractive Combiner of Single-Mode Pump Laser-Diode Beams; Wide-Band, High-Quantum-Efficiency Photodetector; A Robustly Stabilizing Model Predictive Control Algorithm; Modeling Evaporation of Drops of Different Kerosenes; Development of Vapor-Phase Catalytic Ammonia Removal System; Several Developments in Space Tethers; Design Concept for a Nuclear Reactor-Powered Mars Rover; Formation-Initialization Algorithm for N Spacecraft; and DNSs of Multicomponent Gaseous and Drop-Laden Mixing Layers Achieving Transition to Turbulence.

Source record↗

Practical gust load alleviation and flutter suppression control laws based on a LQG methodology

A modified linear quadratic Gaussian (LQG) synthesis procedure has been used to design low-order robust multiloop controllers for a flexible airplane. The introduction of properly constructed fictitious Gauss-Markov processes in the control loops allowed meeting classical frequency-domain stability criteria using the direct synthesis procedures of modern time-domain control theory. Model reduction was used to simplify the control laws to the point where they could be easily implemented on onboard flight computers. These control laws provided excellent gust load and flutter mode control with good stability margins and compared very favorably to other control laws synthesized by the classical root-locus technique.

Gangsaas, D.↗

Robot Control Based On Spatial-Operator Algebra

Method for mathematical modeling and control of robotic manipulators based on spatial-operator algebra providing concise representation and simple, high-level theoretical frame-work for solution of kinematical and dynamical problems involving complicated temporal and spatial relationships. Recursive algorithms derived immediately from abstract spatial-operator expressions by inspection. Transition from abstract formulation through abstract solution to detailed implementation of specific algorithms to compute solution greatly simplified. Complicated dynamical problems like two cooperating robot arms solved more easily.

Rodriguez, Guillermo↗

Drag reduction in channel flow using nonlinear control

Two nonlinear control schemes have been applied to the problem of drag reduction in channel flow. Both schemes have been tested using numerical simulations at a mass flux Reynolds numbers of 4408, utilizing 2D nonlinear neutral modes for goal dynamics. The OGY-method, which requires feedback, reduces drag to 60-80 percent of the turbulent value at the same Reynolds number, and employs forcing only within a thin region near the wall. The H-method, or model-based control, fails to achieve any drag reduction when starting from a fully turbulent initial condition, but shows potential for suppressing or retarding laminar-to-turbulent transition by imposing instead a transition to a low drag, nonlinear traveling wave solution to the Navier-Stokes equation. The drag in this state corresponds to that achieved by the OGY-method. Model-based control requires no feedback, but in experiments to date has required the forcing be imposed within a thicker layer than the OGY-method. Control energy expenditures in both methods are small, representing less than 0.1 percent of the uncontrolled flow's energy.

Keefe, Laurence R.↗

Virtual Deformation Control of the X-56A Model with Simulated Fiber Optic Sensors

A robust control law design methodology is presented to stabilize the X-56A model and command its wing shape. The X-56A was purposely designed to experience flutter modes in its flight envelope. The methodology introduces three phases: the controller design phase, the modal filter design phase, and the reference signal design phase. A mu-optimal controller is designed and made robust to speed and parameter variations. A conversion technique is presented for generating sensor strain modes from sensor deformation mode shapes. The sensor modes are utilized for modal filtering and simulating fiber optic sensors for feedback to the controller. To generate appropriate virtual deformation reference signals, rigid-body corrections are introduced to the deformation mode shapes. After successful completion of the phases, virtual deformation control is demonstrated. The wing is deformed and it is shown that angle-of-attack changes occur which could potentially be used to an advantage. The X-56A program must demonstrate active flutter suppression. It is shown that the virtual deformation controller can achieve active flutter suppression on the X-56A simulation model.

Modal Filter↗

COFS 2: 3-D dynamics and controls technology

The Control of Flexible Structures (COFS) 2 project is a complex and ambitious undertaking which will address several critical technology areas. Among them are modeling, structural dynamics, controls, and ground testing issues which are not only germane to this effort, but to other large space structure programs being contemplated. This effort requires the early integration of controls and structural dynamics considerations in order to achieve mission success. Several technology advances must be achieved in the areas of system modelling, control synthesis and methodology, sensor/actuator development, and ground testing techniques for system evaluation and on-orbit performance prediction and verification. This project offers a unique opportunity for the integration of several disciplines to produce technology advances which will benefit many future programs. In addition, the opportunities available to participate in the various levels in the phase of this project, e.g., analytical development and modelling, ground testing, and flight testing, permit for the involvement of a significant number of interested researchers and organizations from government, universities and industry.

Pyle, Jon S.↗

A tensor approach to modeling of nonhomogeneous nonlinear systems

Model following control methodology plays a key role in numerous application areas. Cases in point include flight control systems and gas turbine engine control systems. Typical uses of such a design strategy involve the determination of nonlinear models which generate requested control and response trajectories for various commands. Linear multivariable techniques provide trim about these motions; and protection logic is added to secure the hardware from excursions beyond the specification range. This paper reports upon experience in developing a general class of such nonlinear models based upon the idea of the algebraic tensor product.

Yurkovich, S.↗

Dynamics and control of a continuum model for a solar power system

An approach for modeling dynamic equations of motion of a plate attached with rigid bodies is presented. The equations of motion are developed using the principle of virtual work. Lagrange multipliers are used as interaction forces and/or moments to maintain prescribed constraints which is the basis of the interconnection between the plate and rigid bodies. The overall approach is unique in the sense that a continuous model described by a family of partial differential equations is established. An approximate formulation by using variational method is established yielding a solution compatible with the assumed degree of approximation. The formulation is useful particularly when parametric study of dynamic response for a satellite power system is desired. As an example, an approximate governing equation of algebraic eigenvalue problem is given for a dual microwave power transmission system. Controller design is discussed.

Juang, J. N.↗

Proceedings of the 3rd Annual SCOLE Workshop

Topics addressed include: modeling and controlling the Spacecraft Control Laboratory Experiment (SCOLE) configurations; slewing maneuvers; mathematical models; vibration damping; gravitational effects; structural dynamics; finite element method; distributed parameter system; on-line pulse control; stability augmentation; and stochastic processes.

Taylor, Lawrence W., Jr.↗

Predictive Workload Model for Air Traffic Controllers during UAM Operations

The effect of airspace factors on air traffic controller (ATC) workload has been an active area of study for almost three decades due to the importance of safety considerations necessary to design and maintain operations. Existing literature has examined several traffic-related (e.g., number of aircraft under control, loss of separation) contributors to ATC workload and proposed mathematical functions to best describe controller response. However, future air traffic continues to increase in complexity with the introduction of urban air mobility (UAM) – or the transportation of humans and cargo using electric vertical takeoff and landing (eVTOL) aircraft. UAM aims to alleviate congestion for existing ground transportation systems and improve mobility within urban centers and other high-demand locations. This shift in the traditional airspace paradigm necessitates an evolved understanding of model use and development for ATC workload prediction. This study aimed to develop an ATC workload forecasting model based on human-in-the-loop (HITL) simulation data for UAM operations at large airports. Data collected from the HITL simulation served as the training and testing data for a Long Short-Term Memory recurrent neural network and enabled time-series forecasting of ATC workload from traffic characteristics. Results demonstrated the potential of LSTM models for forecasting ATC workload 40 minutes into the future and highlighted important considerations for future development.

predictive model↗