Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diffuser Flows”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

The effect of ejector augmentation on test-section flow quality in the Calspan 8-ft transonic wind tunnel

Tests to determine the flow disturbances effects of four ejectors located in the corners just downstream of the diffuser in the Calspan wind tunnel are described. The flow quality in the nonejector mode is employed as the base-line configuration, and operating parameters are compared with data from other wind tunnels. During tests with the ejectors working, fluctuation levels increased between Mach 0.4-0.6, while temperature and vorticity levels remained constant. The ejector exhibited broad spectrum noise typical of free jet noise, yet static pressure measurements revealed only a slight increase in the broadband rms levels with the ejectors on, indicating negligible disturbances upstream caused by the ejectors. Choking the diffuser eliminated the jet noise, and the use of ejectors in the Mach range considered is concluded to cause no significant degradation in the Calspan tunnel flow quality.

Rose, W. C.↗

Supersonic combustor modeling

The physical phenomena involved when a supersonic flow undergoes chemical reaction are discussed. Detailed physical models of convective and diffusive mixing, and finite rate chemical reaction in supersonic flow are presented. Numerical algorithms used to solve the equations governing these processes are introduced. Computer programs using these algorithms are used to analyze the structure of the reacting mixing layer. It is concluded that, as in subsonic flow, exothermic heat release in unconfined supersonic flows retards fuel/air mixing. Non mixing is shown to be a potential problem in reducing the efficiency of supersonic as well as subsonic combustion. Techniques for enhancing fuel/air mixing and combustion are described.

Riggins, David W.↗

Assessment of model assumptions and budget terms of the unsteady flamelet equations for a turbulent reacting jet-in-cross-flow

An a priori analysis of the flamelet model for diffusion flames is conducted to systematically assess model assumptions that are associated with the asymptotic expansion, the omission of higher-order expansion terms, the consideration of preferential diffusion effects, and the one-dimensional flamelet representation. For this, a recent direct numerical simulation database of a reacting hydrogen/air jet-in-cross-flow (JICF) by Grout et al. [15,16] is used. The full flamelet equation for temperature, exact to the order of the Eulerian transport equation and general to different definitions of the mixture fraction, is derived. Analysis of mixture fraction conditioned profiles of temperature and scalar dissipation rate along the jet trajectory identified different ignition and flame stabilization scenarios on the windward and leeward sides of the reacting JICF. A balance analysis of the temperature flamelet equation is conducted to quantify contributions in flame-aligned and flame-orthogonal directions. Consistent with the flamelet assumption, it is shown that terms arising from scalar diffusion, heat-release, and species-diffusion-induced enthalpy flux are the dominant contributions, while the flame-aligned preferential diffusion promotes entrainment of heat into the flamelet structure. Finally, for the current JICF-configuration, it is found that contributions along the flame-orthogonal direction are on average negligible.

42 ENGINEERING↗

Impact of the Out‐Of‐Plane Flow Shear on Magnetic Reconnection at the Flanks of Earth's Magnetopause

Abstract Magnetic reconnection changes the magnetic field topology and facilitates the energy and particle exchange at magnetospheric boundaries such as the Earth's magnetopause. The flow shear perpendicular to the reconnecting plane prevails at the flank magnetopause under southward interplanetary magnetic field conditions. However, the effect of the out‐of‐plane flow shear on asymmetric reconnection is an open question. In this study, we utilize kinetic simulations to investigate the impact of the out‐of‐plane flow shear on asymmetric reconnection. By systematically varying the flow shear strength, we analyze the flow shear effects on the reconnection rate, the diffusion region structure, and the energy conversion rate. We find that the reconnection rate increases with the upstream out‐of‐plane flow shear, and for the same upstream conditions, it is higher at the dusk side than at the dawn side. The diffusion region is squeezed in the outflow direction due to magnetic pressure which is proportional to the square of the Alfvén Mach number of the shear flow. The out‐of‐plane flow shear increases the energy conversion rate , and for the same upstream conditions, the magnitude of is larger at the dusk side than at the dawn side. This study reveals that out‐of‐plane flow shear not only enhances the reconnection rate but also significantly boosts energy conversion, with more pronounced effects on the dusk‐side flank than on the dawn‐side flank. These insights pave the way for better understanding the solar wind‐magnetosphere interactions.

Liang, Haoming↗

Deep Learning Emulation of Subgrid-Scale Processes in Turbulent Shear Flows

Deep neural networks (DNNs) are developed from a data set obtained from the dynamic Smagorinsky model to emulate the subgrid-scale (SGS) viscosity (ν sgs ) and diffusivity (κ sgs ) for turbulent stratified shear flows encountered in the oceans and the atmosphere. These DNNs predict ν sgs and κ sgs from velocities, strain rates, and density gradients such that the evolution of the kinetic energy budget and density variance budget terms is similar to the corresponding values obtained from the original dynamic Smagorinsky model. These DNNs also compute ν sgs and κ sgs ~2–4 times quicker than the dynamic Smagorinsky model resulting in a ~2–2.5 times acceleration of the entire simulation. This study demonstrates the feasibility of deep learning in emulating the subgrid-scale (SGS) phenomenon in geophysical flows accurately in a cost-effective manner. In a broader perspective, deep learning-based surrogate models can present a promising alternative to the traditional parameterizations of the subgrid-scale processes in climate models.

58 GEOSCIENCES↗

Analytical investigation of conical diffusers

A study was made to determine if existing data for straight-channel single-plane divergence diffusers together with boundary-layer methods could be practically employed to predict conical diffuser performance in the high-speed flow regime. A semiempirical correlation technique, which uses the experimental performance of a straight-channel single-plane divergence diffuser, and a momentum integral boundary-layer method were employed to predict conical diffuser performance. Neither of these methods is applicable when the boundary layer separates. The momentum integral method was used to study the relative importance of various boundary layer parameters in correlating unstalled diffuser performance. Other investigators have found that the best diffuser performance occurs when the diffuser is operating in the transitory stall regime. Since the analytical methods presented in this report are not applicable after the point of boundary-layer separation, a criterion was established from examination of experimental tests which allows the designer to ascertain approximate diffuser performance in the transitory stall regime.

Means, J. L.↗

Aspects of turbulent combustion

A complete second-order closure program for the investigation of chemically reacting turbulent flowfields is being developed. Many of the turbulence models being used have been developed and tested during previous studies of a variety of incompressible and compressible shear flows. A number of additional scalar correlations have to be modeled for chemically reacting flows, and a 'typical eddy' model has been developed for the joint probability density function for all the scalars. A simpler model in which higher-order scalar correlations are set zero is also being used. The program has been recently extended to multi-species, multi-step chemical reactions. Computations have been performed using the second-order closure program to study the turbulence-chemistry interaction in DF chemical laser flows and in a hydrogen-air diffusion flame. The results demonstrate the importance of the inclusion of the concentration and temperature fluctuation correlations in turbulent reacting flows.

Varma, A. K.↗

The Shuttle Orbiter high resolution accelerometer package experiment - Preliminary flight results

A description of the High Resolution Accelerometer Package (HiRAP) experiment, designed to measure rarefied flow aerodynamic accelerations, is given. The ground test calibration factors, as well as post-flight data processing techniques to extract aerodynamic accelerations, are discussed and applied to the recorded reentry data of the recent STS-6 Shuttle Orbiter flight. The ratio of the measured normal-to-axial aerodynamic accelerations during reentry is used to obtain the first flight measurement of the lift-to-drag ratio (L/D) of a winged entry vehicle in the rarefied flow flight regime. The preliminary result for the free-molecule flow L/D is 0.10 + or - 0.03. The initial flight results on L/D are compared with current predictions which are based upon theoretical and empirical considerations. The measured free-molecule flow L/D value is higher than predicted by a factor of about three, indicating that surface reflection is not completely diffuse as currently assumed. In the rarefied flow transition regime, the Shuttle data book-bridging formula fits the flight data adequately. Upper altitude density profiles are also deduced from the measurements and presented. The density profiles show a wave phenomena with amplitude of about 60 percent, relative to a standard model.

Blanchard, R. C.↗

SIMULATION OF RARE ISOTOPE RELEASE FROM ISOL TARGET

Releases of short-lived species from ISOL targets are simulated with computer codes. Analytic solutions to the diffusion equation are compared with those obtained from a finite-difference code for radioactive isotope diffusion release from simple geometry targets. The Monte Carlo technique as a practical means for vapor transport system design is demonstrated by simulating the effusive-flow of neutral particles through complex target-vapor transport systems. Particle release curves involving decay losses in both diffusion and effusive-flow are computed; and a numerical procedure is proposed to measure the diffusion coefficients and the characteristic effusion times of rare isotopes in target-ion source systems.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: 1) a k-epsilon turbulence model computation on a 6.8 million point grid using wall functions, 2) a k-epsilon turbulence model computation on a 14 million point grid integrating to the wall, and 3) a k-omega turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-epsilon and k-omega computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-epsilon computations which extended from 70% to 100% span at the exit rating plane, whereas the k-omega computation had reversed flow from 95% to 100% span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-epsilon case resulted in an under-prediction in adiabatic efficiency of 8.3 points, whereas the k-omega case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗

Computational Study of the CC3 Impeller and Vaneless Diffuser Experiment

Centrifugal compressors are compatible with the low exit corrected flows found in the high pressure compressor of turboshaft engines and may play an increasing role in turbofan engines as engine overall pressure ratios increase. Centrifugal compressor stages are difficult to model accurately with RANS CFD solvers. A computational study of the CC3 centrifugal impeller in its vaneless diffuser configuration was undertaken as part of an effort to understand potential causes of RANS CFD mis-prediction in these types of geometries. Three steady, periodic cases of the impeller and diffuser were modeled using the TURBO Parallel Version 4 code: (1) a k-ε turbulence model computation on a 6.8 million point grid using wall functions, (2) a k-ε turbulence model computation on a 14 million point grid integrating to the wall, and (3) a k-ω turbulence model computation on the 14 million point grid integrating to the wall. It was found that all three cases compared favorably to data from inlet to impeller trailing edge, but the k-ε and k-ω computations had disparate results beyond the trailing edge and into the vaneless diffuser. A large region of reversed flow was observed in the k-ε computations which extended from 70 to 100 percent span at the exit rating plane, whereas the k-ω computation had reversed flow from 95 to 100 percent span. Compared to experimental data at near-peak-efficiency, the reversed flow region in the k-ε case resulted in an underprediction in adiabatic efficiency of 8.3 points, whereas the k-ω case was 1.2 points lower in efficiency.

Kulkarni, Sameer↗

Turbulent Jet Flames Into a Vitiated Coflow

Examined is the vitiated coflow flame, an experimental condition that decouples the combustion processes of flows found in practical combustors from the associated recirculating fluid mechanics. The configuration consists of a 4.57 mm diameter fuel jet into a coaxial flow of hot combustion products from a lean premixed flame. The 210 mm diameter coflow isolates the jet flame from the cool ambient, providing a hot environment similar to the operating conditions of advanced combustors; this important high temperature element is lacking in the traditional laboratory experiments of jet flames into cool (room) air. A family of flows of increasing complexity is presented: 1) nonreacting flow, 2) all hydrogen flame (fuel jet and premixed coflow), and 3) set of methane flames. This sequence of experiments provides a convenient ordering of validation data for combustion models. Laser Raman-Rayleigh-LIF diagnostics at the Turbulent Diffusion Flame laboratory of Sandia National Laboratories produced instantaneous multiscalar point measurements. These results attest to the attractive features of the vitiated coflow burner and the well-defined boundary conditions provided by the coflow. The coflow is uniform and steady, isolating the jet flame from the laboratory air for a downstream distance ranging from z/d = 50-70. The statistical results show that differential diffusion effects in this highly turbulent flow are negligible. Complementing the comprehensive set of multiscalar measurements is a parametric study of lifted methane flames that was conducted to analyze flame sensitivity to jet and coflow velocity, as well as coflow temperature. The linear relationship found between the lift-off height and the jet velocity is consistent with previous experiments. New linear sensitivities were found correlating the lift-off height to coflow velocity and temperature. A blow-off study revealed that the methane flame blows off at a common coflow temperature (1260 K), regardless of coflow or jet velocity. An explanation for this phenomenon is that entrainment of ambient air at the high lift-off heights prevents autoignition. Analysis of the results suggests that flame stabilization occurs through a combination of flame propagation, autoignition, and localized extinction processes. Proposed is an expanded view of distributed reaction combustion based on analysis of the distributions of probe volume conditions at the stabilization region of the lifted hydrogen and methane flames. Turbulent eddies the size of the flame thickness mix fuel and hot coflow across the flame front, thereby enhancing the reaction zone with autoignition of reactants at elevated temperatures; this is the reverse effect of turbulent flames in ambient air, where intense turbulence in cool mixtures result in localized extinction. Each of the three processes (i.e., flame propagation, autoignition and localized extinction) contributes to flame stabilization in varying degrees, depending on flow conditions.

Holdeman, James D.↗

Solutions for Reacting and Nonreacting Viscous Shock Layers with Multicomponent Diffusion and Mass Injection

Numerical solutions are presented for the viscous shocklayer equations where the chemistry is treated as being either frozen, equilibrium, or nonequilibrium. Also the effects of the diffusion model, surface catalyticity, and mass injection on surface transport and flow parameters are considered. The equilibrium calculations for air species using multicomponent: diffusion provide solutions previously unavailable. The viscous shock-layer equations are solved by using an implicit finite-difference scheme. The flow is treated as a mixture of inert and thermally perfect species. Also the flow is assumed to be in vibrational equilibrium. All calculations are for a 45 deg hyperboloid. The flight conditions are those for various altitudes and velocities in the earth's atmosphere. Data are presented showing the effects of the chemical models; diffusion models; surface catalyticity; and mass injection of air, water, and ablation products on heat transfer; skin friction; shock stand-off distance; wall pressure distribution; and tangential velocity, temperature, and species profiles.

Moss, J. N.↗

Effect of flow-field structure on discharging and charging behavior of hydrogen/bromine redox flow batteries

Designing and optimizing the flow-field structure for the liquid phase Br 2 /HBr electrolyte solution of H 2 /Br 2 redox flow batteries (RFBs) is important for improving cell performance. In this study, two electrolyte flow modes, i.e. the flow-by and flow-through modes, are simulated by using a three-dimensional H 2 /Br 2 RFB model. The model is first applied to real-scale H 2 /Br 2 cell geometries and then validated against the experimental polarization curves acquired using the two different flow modes. The model predictions compare well with the experimental data and further highlight the advantages of using the flow-through mode relative to the flow-by mode. Detailed multi-dimensional contours of the electrolyte flow velocity and key species distributions reveal that more uniform diffusion and stronger convective transport are achieved by using the flow-through mode, which alleviates the ohmic loss associated with charge transport in the Br 2 electrode.

25 ENERGY STORAGE↗

Diurnal variations in the thermosphere. II - Temperature, composition, and winds

The fundamental diurnal component of temperature, composition and wind fields is discussed for the thermosphere, the results delineated in terms of energy sources in the lower atmosphere, mesosphere and thermosphere, illustrating their relative significance. The diurnal component in the composition of H, He, O, O2 and Ar has been analyzed in terms of effects from thermal expansion in diffusive equilibrium and transport processes associated with chemistry, wind circulation, exospheric flow and escape. Next to thermal expansion, wind-induced diffusion is the single most important process; it dominates the diurnal variations of He and prevails in the variations of O, O2 and Ar below 200 km.

Mayr, H. G.↗

Measurement of fluid properties using rapid-double-exposure and time-average holographic interferometry

The holographic recording of the time history of a flow feature in three dimensions is discussed. The use of diffuse illumination holographic interferometry or the three-dimensional visualization of flow features such as shock waves and turbulent eddies is described. The double-exposure and time-average methods are compared using the characteristic function and the results from a flow simulator. A time history requires a large hologram recording rate. Results of holographic cinematography of the shock waves in a flutter cascade are presented as an example. Future directions of this effort, including the availability and development of suitable lasers, are discussed. Previously announced in STAR as N84-21849

Decker, A. J.↗

Dynamic evolution of low-energy ions in the terrestrial magnetosphere

Results of a statistical study of low-energy (0-50 eV) field-aligned ion pitch angle distributions for H(+), He(+), and O(+) observed by the Dynamics Explorer retarding ion mass spectrometer instrument are presented. Ion distributions are characterized as uni- and bi-directional field-aligned and bi-directional conic distributions. The spatial relationships of these distributions can be interpreted as dynamic evolution of low-energy ion flow in which injected unidirectional field-aligned streams originating in the nightside auroral zone evolve first into bi-directional flows under the influence of convection in the mirror magnetic field configuration. Characteristic convection times are evaluated with a pitch angle diffusion model in which field-aligned flows evolve into conical distributions through charge exchange loss of particles to the atmosphere during particle mirroring periods.

Giles, B. L.↗

Opposed-Flow Flame Spreading in Reduced Gravity

Experimental results obtained in drop towers and in Space Shuttle based experiments coupled with modelling efforts are beginning to provide information that is allowing an understanding to be developed of the physics of opposed-flow flame spread at reduced gravity where the spread rate and flow velocity are comparable and of the role played by radiative and diffusive processes in flame spreading in microgravity. Here we describe one Space Shuttle based experiment on flame spreading in a quiescent environment, the Solid Surface Combustion Experiment, SSCE, one planned microgravity experiment on flame spreading in a radiatively-controlled, forced opposing flow environment, the Diffusive and Radiative Transport in Fires Experiment, DARTFire, modelling efforts to support these experiments, and some results obtained to date.

Altenkirch, Robert A.↗