Search NASA⌕ Search

SEARCH · Search NASA

Results for “Dislocation structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Mechanisms of ultrafine-grained austenite formation under different isochronal conditions in a cold-rolled metastable stainless steel

The primary objective of this work is to obtain fundamental insights on phase transformations, with focus on the reaustenitization process (α′→γ transformation), of a cold-rolled (CR) semi-austenitic metastable stainless steel upon different isochronal conditions (0.1, 1, 10 and 100 °C/s). For this purpose, an exhaustive microstructural characterization has been performed by using complementary experimental such as scanning and transmission electron microscopy (SEM and TEM), electron backscattered diffraction (EBSD), electron probe microanalysis (EPMA), micro-hardness Vickers and magnetization measurements. It has been detected that all microstructural changes shift to higher temperatures as the heating rate increases. The reaustenitization occurs in two-steps for all heating rates, which is attributed to the chemical banding present in the CR state. The α′→γ transformation is controlled by the migration of substitutional alloying elements across the austenite/martensite (γ/α′) interface, which finally leads to ultrafine-grained reaustenitized microstructures (440–280 nm). The morphology of the martensite phase in the CR state has been found to be the responsible for such a grain refinement, along with the presence of χ-phase and nanometric Ni{sub 3}(Ti,Al) precipitates that pin the austenite grain growth, especially upon slowly heating at 0.1 °C/s. - Highlights: •Ultrafine-grained austenite structures are obtained isochronally at 0.1–100 °C/s •The α′→γ transformation occurs in two steps due to the initial chemical banding •A diffusional mechanism governs the α′→γ transformation for all heating rates •The dislocation-cell-type of martensite promotes a diffusional mechanism •Precipitates located at α′/γ interfaces hinder the austenite growth.

36 MATERIALS SCIENCE↗

Defect engineering in nickel via electrodeposition following low temperature annealing

Electrodeposited nickel coatings are characterized by high densities of crystalline defects including dislocations, growth twins, and hydrogen bubbles/voids, arising from the non-equilibrium nature of deposition. While these metastable features influence as-deposited properties, their evolution under low temperature annealing remains unexplored. Here, in this study, we demonstrate that low temperature annealing (200 °C) induces significant microstructural rearrangement without grain growth, enabling defect engineering through thermally assisted dislocation motion and twin boundary migration. Notably, we observe faceted twin boundaries and dislocation organization into extended networks, which have been rarely reported under such annealing conditions. These transformations are attributed to hydrogen-assisted defect mobility, facilitated by the release or redistribution of hydrogen trapped during deposition. These structural transformations correlate with a significant enhancement in mechanical properties, including a twofold increase in yield strength and improved ductility. Our findings highlight the role of trapped hydrogen in mediating low-temperature defect mobility and twin boundary evolution, offering a unique pathway for microstructural tuning of metallic coatings through controlled annealing.

36 - MATERIALS SCIENCE↗

Microstructure and magnetic properties of FeCo epitaxial thin films grown on MgO single-crystal substrates

FeCo epitaxial films were prepared on MgO(100), MgO(110), and MgO(111) substrates by ultrahigh vacuum molecular beam epitaxy. FeCo thin films with (100), (211), and (110) planes parallel to the substrate surface grow on respective MgO substrates. FeCo/MgO interface structures are studied by high-resolution cross-sectional transmission electron microscopy and the epitaxial growth mechanism is discussed. Atomically sharp boundaries are recognized between the FeCo thin films and the MgO substrates where misfit dislocations are introduced in the FeCo thin films presumably to decrease the lattice misfits. Misfit dislocations are observed approximately every 9 and 1.4 nm in FeCo thin film at the FeCo/MgO(100) and the FeCo/MgO(110) interfaces, respectively. X-ray diffraction analysis indicates that the lattice spacing measured parallel to the single-crystal substrate surfaces are in agreement within 0.1% with those of the respective bulk values of Fe{sub 50}Co{sub 50} alloy crystal, showing that the FeCo film strain is very small. The magnetic anisotropies of these epitaxial films basically reflect the magnetocrystalline anisotropy of bulk FeCo alloy crystal.

36 MATERIALS SCIENCE↗

Vertical GaN power diodes with a bilayer edge termination

Vertical GaN power diodes with a bilayer edge termination (ET) are demonstrated. The GaN p-n junction is formed on a low threading dislocation defect density (10 4 - 10 5 cm -2 ) GaN substrate, and has a 15-μm-thick n-type drift layer with a free carrier concentration of 5 × 10 15 cm -3 . The ET structure is formed by N implantation into the p+-GaN epilayer just outside the p-type contact to create compensating defects. The implant defect profile may be approximated by a bilayer structure consisting of a fully compensated layer near the surface, followed by a 90% compensated (p) layer near the n-type drift region. These devices exhibit avalanche breakdown as high as 2.6 kV at room temperature. In addition simulations show that the ET created by implantation is an effective way to laterally distribute the electric field over a large area. This increases the voltage at which impact ionization occurs and leads to the observed higher breakdown voltages.

42 ENGINEERING↗

Optimization of the Growth Technology for Crystals with Garnet Structure Based on X-Ray Diffraction Data

High efficiency of the methods of double-crystal X-ray diffractometry (DCXRD) and topography for improving the growth technology of highly homogeneous crystals has been demonstrated on the example of gadolinium gallium garnet (GGG) single crystals. The main types of structural defects observed in Czochralski-grown GGG crystals are found to be macroscopic inhomogeneity of composition distribution, caused by the facet effect manifestation; microinhomogeneous distribution of impurity and main components of the composition in striations; dislocations; and second-phase inclusions. The relationship between the type and density of newly formed defects and the technological conditions for crystal growth are considered. Optimization of the composition of crystals and their growth technology made it possible to obtain high-quality dislocation-free crystals of GGG and complex-substituted garnets on its basis for magneto-optical and microwave devices, elements of solid-state lasers, and other applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Program Managers Questions for LL13-MatModelRadDetect-2Jf

The major project goals are three-fold: 1) to determine the mechanisms of polarization of TlBr detectors related to electrical contact materials, and enable the rational design of optimal contact stacks for maximum detector longevity; 2) to elucidate the carrier trapping propensity of dislocations in CdTe/CZT and determine whether this depends on type and decoration of the dislocations; evaluate whether dislocation engineering (out of scope of this project) can optimize CZT detector performance; 3) to discover if (and how) a glass material can make a high-performance host for a scintillator, by understanding how atomic structure differences associated with composition and forming conditions affect carrier transport.

36 MATERIALS SCIENCE↗

Friction stir processing of an aluminum-magnesium alloy with pre-placing elemental titanium powder: In-situ formation of an Al{sub 3}Ti-reinforced nanocomposite and materials characterization

A fine-grained Al–Mg/Al{sub 3}Ti nanocomposite was fabricated by friction stir processing (FSP) of an aluminum-magnesium (AA5052) alloy with pre-placed titanium powder in the stirred zone. Microstructural evolutions and formation of intermetallic phases were analyzed by optical and electron microscopic techniques across the thickness section of the processed sheets. The microstructure of the nanocomposite consisted of a fine-grained aluminum matrix (1.5 µm), un-reacted titanium particles (<40 µm) and reinforcement particles of Al{sub 3}Ti (<100 nm) and Mg{sub 2}Si (<100 nm). Detailed microstructural analysis indicated solid-state interfacial reactions between the aluminum matrix and micro-sized titanium particles to form Al{sub 3}Ti intermetallic phase. The hard inclusions were then fractured and re-distributed in the metal matrix by the severe thermo-mechanical conditions imposed by FSP. Evaluation of mechanical properties by hardness measurement and uniaxial tensile test determined significant enhancement in the mechanical strength (by 2.5 order of magnetite) with a high ductility (~22%). Based on a dislocation-based model analysis, it was suggested that the strength enhancement was governed by grain refinement and the presence of hard inclusions (4 vol%) in the metal matrix. Fractographic studies also showed a ductile-brittle fracture mode for the nanocomposite compared with fully ductile rupture of the annealed alloy as well as the FSPed specimen without pre-placing titanium particles. - Highlights: • FSP was employed to fabricate in situ nanocomposite. • The AA5052 Al alloy with pre-placed micro-sized Ti particles were utilized. • The structural analysis was revealed that the in situ formation of Al{sub 3}Ti nanophase. • The SZ grain structure was refined by PSN and ZHP mechanisms during DRX. • Hardness and tensile strength were improved up to ~2.5 times with a good ductility.

36 MATERIALS SCIENCE↗

Hydrogen Embrittlement of Pipeline Steels: Causes and Remediation

Fundamental studies of hydrogen embrittlement of materials using both experimental observations and numerical simulations of the hydrogen/deformation interactions have been conducted. Our approach integrates mechanical property testing at the macro-scale, microstructural analyses and TEM observations of the deformation processes at the micro- and nano-scale, first-principles calculations of interfacial cohesion at the atomic scale, and finite element simulation and modeling at the micro- and macro-level. Focused Ion Beam machining in conjunction with Transmission Electron Microscopy were used to identify the salient micro-mechanisms of failure in the presence of hydrogen. Our analysis of low strength ferritic steels led to the discovery that “quasi-cleavage” is a dislocation plasticity controlled failure mode in agreement with the hydrogen enhanced plasticity mechanism. The microstructure underneath the fracture surface of 304 and 316 stainless steels was found to be significantly more complex than would have been predicted by the traditional models of fatigue. The general refinement of the microstructure that occurred near the fracture surface in the presence of hydrogen was such that one may argue that hydrogen stabilizes microstructural configurations to an extent not achievable in its absence. Finite element studies of hydrogen and deformation field similitude for cracks in real-life pipelines and laboratory fracture specimens yielded that the Single Edge Notch Tension specimen can be used to reliably study hydrogen material compatibility for pipeline structures. In addition, simulation of onset of crack propagation in low strength ferritic systems by void growth indicated that hydrogen can reduce the fracture toughness of the material by as much as 30%. Both experimental observations and numerical studies of hydrogen transport on hydrogen accumulations ahead of a crack tip yielded that dislocation transport can markedly enhance hydrogen populations which in turn can trigger fracture initiation.

08 HYDROGEN↗

Interface, bulk and surface structure of heteroepitaxial altermagnetic α-MnTe films grown on GaAs(111)

Epitaxial MnTe films have recently seen a surge in research into their altermagnetic semiconducting properties. However, those properties may be extremely sensitive to structural and chemical modifications. We report a detailed investigation of the synthesis of the altermagnet α-MnTe on GaAs(111), which reveals the bulk defect structure of this material, the mechanism by which it releases strain from the underlying substrate, and the impact of oxidation on its surface. X-ray diffraction measurements show that α-MnTe layers with thicknesses spanning 45 to 640 nm acquire lattice parameters different from bulk, mostly due to thermal strain caused by the substrate rather than strain from the lattice mismatch. Through high-resolution transmission electron microscopy (TEM) measurement, we then unveil a misfit dislocation array at the interface, revealing the mechanism by which lattice strain is relaxed. TEM also reveals a stacking fault in the bulk, occurring along a glide plane parallel to the interface. The combination of TEM with polarized neutron reflectometry measurements finally reveals the impact of oxidation on the chemistry of the surface of uncapped MnTe. Furthermore, or findings highlight the subtle role of epitaxy in altering the structure of α-MnTe, providing potential opportunities to tune the altermagnetic properties of this material.

Altermagnets↗

A micro-alloyed ferritic steel strengthened by nanoscale precipitates

A ferritic steel with finely dispersive precipitates was investigated to reveal the fundamental strengthening mechanisms. The steel has a yield strength of 760 MPa, approximately three times higher than that of conventional Ti-bearing high strength hot-rolled sheet steels, and its ultimate tensile strength reaches 850 MPa with an elongation-to-failure value of 18%. Using energy dispersive X-ray spectroscopy (EDXS) and transmission electron microscope (TEM), fine carbides TiC with an average diameter of 10 nm were observed in the ferrite matrix of the 0.08%Ti steel, and some cubic M23C6 precipitates were also observed at the grain boundaries and the interior of the grains. The finely dispersive TiC precipitates in the matrix provide matrix strengthening. The estimated magnitude of precipitation strengthening is around 458 MPa, depending on the average size of the nanoscale precipitates. Dislocation densities increased from 3.42×1013 m-2 to 1.69 × 1014 m-2, respectively, with increasing tensile strain from 5.5% to 22%. The measured work-hardening behavior can be related to the observed dislocation accumulations resulting from the dispersive nano-scale precipitates.

36 MATERIALS SCIENCE↗

New insights on the formation of supersaturated Cu-Nb solid solution prepared by mechanical alloying

The deformation-driven alloying mechanisms in the immiscible Cu-Nb system during mechanical alloying (MA) process have been studied by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and high-resolution TEM (HRTEM) observations. It is found that the dominating alloying mechanism changes at the different stages of milling. Initially, the alloying process is mainly governed by interfaces and dislocations, which supply fast diffusion channels between phases. In the intermediate stage, Nb particles with sizes below 8 nm undergo a bcc to fcc allotropic transformation, and the interdiffusion between fcc-Nb and fcc-Cu is promoted due to the similarity of lattice structures. Further milling generates disclination defects, which contribute to the formation of fragments or subgrains with sizes below 5 nm. The introduction of such defects and fragments benefits the formation of a complete Cu-Nb solid solution. The formation kinetics of solid solution is analyzed by Johnson-Mehl-Avrami equation, which suggests that the speed of the diffusion of Nb atoms into Cu is very slow. - Highlights: •The bcc to fcc transformation in Nb nanoparticles promotes diffusion process. •The formation of fragments with sizes below 5 nm is attributed to the disclination defects. •Defect-assisted diffusion is responsible for the alloying process.

36 MATERIALS SCIENCE↗

Correlating electroluminescence characterization and physics-based models of InGaN/GaN LEDs: Pitfalls and open issues

Electroluminescence (EL) characterization of InGaN/GaN light-emitting diodes (LEDs), coupled with numerical device models of different sophistication, is routinely adopted not only to establish correlations between device efficiency and structural features, but also to make inferences about the loss mechanisms responsible for LED efficiency droop at high driving currents. The limits of this investigative approach are discussed here in a case study based on a comprehensive set of current- and temperature-dependent EL data from blue LEDs with low and high densities of threading dislocations (TDs). First, the effects limiting the applicability of simpler (closed-form and/or one-dimensional) classes of models are addressed, like lateral current crowding, vertical carrier distribution nonuniformity, and interband transition broadening. Then, the major sources of uncertainty affecting state-of-the-art numerical device simulation are reviewed and discussed, including (i) the approximations in the transport description through the multi-quantum-well active region, (ii) the alternative valence band parametrizations proposed to calculate the spontaneous emission rate, (iii) the difficulties in defining the Auger coefficients due to inadequacies in the microscopic quantum well description and the possible presence of extra, non-Auger high-current-density recombination mechanisms and/or Auger-induced leakage. In the case of the present LED structures, the application of three-dimensional numerical-simulation-based analysis to the EL data leads to an explanation of efficiency droop in terms of TD-related and Auger-like nonradiative losses, with a C coefficient in the 10{sup −30} cm{sup 6}/s range at room temperature, close to the larger theoretical calculations reported so far. However, a study of the combined effects of structural and model uncertainties suggests that the C values thus determined could be overestimated by about an order of magnitude. This preliminary attempt at uncertainty quantification confirms, beyond the present case, the need for an improved description of carrier transport and microscopic radiative and nonradiative recombination mechanisms in device-level LED numerical models.

36 MATERIALS SCIENCE↗

Nano-scale microstructure damage by neutron irradiations in a novel Boron-11 enriched TiB 2 ultra-high temperature ceramic

Ultra-high temperature transition-metal ceramics are potential candidates for fusion reactor structural and plasma-facing components. We reveal the irradiation damage microstructural phenomena in Boron-11 enriched titanium diboride (TiB 2 ) using mixed-spectrum neutron irradiations, combined with state-of-art characterization using transmission electron microscopy (TEM) and high resolution TEM. Irradiations were performed using High Flux Isotope Reactor at ~220 and 620 °C up to 2.4 x 10 25 n.m -2 (E > 0.1 MeV). The calculated dose including contribution from residual Boron-10 ( 10 B) transmutation recoils, was ~4.2 displacements per atom. TiB 2 is susceptible to irradiation damage in terms of dislocation loop formation, cavities and anisotropic swelling induced micro-cracking. At both 220 and 620 °C, TEM revealed dislocation loops on basal and prism planes, with nearly two orders of magnitude higher number density of prism-plane loops. HRTEM, electron diffraction and relrod imaging revealed additional defects on {10$ \overline{1}\ $0} planes, identified as faulted prism-plane dislocation loops. High defect cluster density on prism planes will induce a-lattice parameter swelling of TiB 2 , as reported in literature. This anisotropic lattice parameter swelling induced grain boundary micro-cracking, the extent of which decreased with increasing irradiation temperature. The dominance of irradiation defect clusters on prism planes is different than typical hexagonal ceramics where dislocation loops predominantly form on basal planes, causing c-lattice parameter swelling. Helium generation and temperature rise from the transmutation of residual 10 B resulted in matrix and grain boundary cavities for the irradiation at 620 °C. In conclusion, the study additionally signifies isotopic enrichment as a viable approach to produce transition-metal diborides for potential nuclear structural applications.

36 MATERIALS SCIENCE↗

Radiation tolerance of neutron-irradiated model Fe-Cr-Al alloys

The Fe Cr Al alloy system has the potential to form an important class of enhanced accident-tolerant cladding materials in the nuclear power industry owing to the alloy system's higher oxidation resistance in high-temperature steam environments compared with traditional zirconium-based alloys. However, radiation tolerance of Fe Cr Al alloys has not been fully established. In this study, a series of Fe Cr Al alloys with 10 18 wt % Cr and 2.9 4.9 wt % Al were neutron irradiated at 382 C to 1.8 dpa to investigate the irradiation-induced microstructural and mechanical property evolution as a function of alloy composition. Dislocation loops with Burgers vector of a/2 111 and a 100 were detected and quantified. Results indicate precipitation of Cr-rich is primarily dependent on the bulk chromium composition. Mechanical testing of sub-size-irradiated tensile specimens indicates the hardening response seen after irradiation is dependent on the bulk chromium composition. Furthermore, a structure property relationship was developed; it indicated that the change in yield strength after irradiation is caused by the formation of these radiation-induced defects and is dominated by the large number density of Cr-rich α' precipitates at sufficiently high chromium contents after irradiation.

36 MATERIALS SCIENCE↗

Unusual size effects from tilted twin boundaries in nano-twinned metals

Tilted twin boundaries (TBs), whose plane normals are rotated at an angle from the parent grain axis, naturally occur in columnar-grained, nano-twinned (NT) metals. Here, using a combination of atomistic simulations and analytical modeling, we reveal that NT metals with the ideal, non-tilted TBs exhibit continuously increasing strength with decreasing twin thickness, and hence, no inverse twin thickness size effect on strength. In contrast, NT metals with tilted TBs exhibit an inverse size effect, and the critical twin thickness, below which strength decreases, increases as the TB-tilt angle increases. The analysis also identifies a critical value of TB tilt, for which strength becomes independent of twin thickness and is the weakest. The transition arises from a change in dislocation activity prevailing mostly on planes inclined to TBs to planes parallel to the TBs. Overall, these findings reveal a profound influence of TB tilt angle that could redirect the analysis and engineering of nano-twin structures.

36 MATERIALS SCIENCE↗

Creep property and microstructure evolution of a nickel-base single crystal superalloy in [011] orientation

The creep property and microstructure evolution of a single crystal superalloy with [011] orientation were investigated at the temperatures of 700 °C, 900 °C and 1040 °C. It is shown that there exist stages of primary, steady-state, and tertiary creep under the lower temperature 700 °C. As the temperature increases to high temperatures of 900 °C and 1040 °C, steady-state creep stage is reduced or disappears and the shape of creep curves is dominated by an extensive tertiary stage. The minimum creep strain rate exhibits power law dependence on the applied stress; the stress exponents at 700 °C, 900 °C and 1040 °C are 28, 13 and 6.5, respectively. Microstructure observation shows that the morphologies of γ′ phase almost keep original shape at the lower temperature 700 °C and high applied stress. With the increasing creep temperature, γ′ precipitates tend to link together and form lamellar structure at an angle of 45° inclined to the applied stress. Transmission electron microscopy (TEM) investigations reveal that multiple < 110 > (111) slip systems gliding in the matrix channels and shearing γ′ precipitates by stacking faults or bending dislocation pairs are the main deformation mechanism at the lower temperature of 700 °C. At the high temperatures of 900 °C and 1040 °C, dislocation networks are formed at γ/γ′ interfaces and the γ′ rafts are sheared by dislocation pairs. - Highlights: • Creep properties of < 011 >-oriented single crystal superalloys were investigated. • γ′ phases become rafting at an angle of 45° inclined to the applied stress. • Creep deformation mechanisms depend on temperature and stress.

36 MATERIALS SCIENCE↗

Understanding and predicting damage and failure at grain boundaries in BCC Ta

Understanding the effect of grain boundaries (GBs) on the deformation and spall behavior is critical to designing materials with tailored failure responses under dynamic loading. This understanding is hampered by the lack of in situ imaging capability with the optimum spatial and temporal resolution during dynamic experiments, as well as by the scarcity of a systematic data set that correlates boundary structure to failure, especially in BCC metals. To fill in this gap in the current understanding, molecular dynamics simulations are performed on a set of 74 bi-crystals in Ta with a [110] symmetric tilt axis. Our results show a correlation between GB misorientation angle and spall strength and also highlight the importance of GB structure itself in determining the spall strength. Specifically, we find a direct correlation between the ability of the GB to plasticity deform through slip/twinning and its spall strength. Additionally, a change in the deformation mechanism from dislocation-meditated to twinning-dominated plasticity is observed as a function of misorientation angles, which results in lowered spall strengths for high-angle GBs.

Chen, J. (ORCID:000000018633229X)↗

Scaled free energies, power-law potentials, strain pseudospins, and quasiuniversality for first-order structural transitions

We consider ferroelastic first-order phase transitions with N{sub OP} order-parameter strains entering Landau free energies as invariant polynomials that have N{sub V} structural-variant Landau minima. The total free energy includes (seemingly innocuous) harmonic terms, in the n=6-N{sub OP} nonorder-parameter strains. Four three-dimensional (3D) transitions are considered, tetragonal/orthorhombic, cubic/tetragonal, cubic/trigonal, and cubic/orthorhombic unit-cell distortions, with, respectively, N{sub OP}=1, 2, 3, and 2; and N{sub V}=2, 3, 4, and 6. Five two-dimensional (2D) transitions are also considered, as simpler examples. Following Barsch and Krumhansl, we scale the free energy to absorb most material-dependent elastic coefficients into an overall prefactor, by scaling in an overall elastic energy density; a dimensionless temperature variable; and the spontaneous-strain magnitude at transition {lambda}<<1. To leading order in {lambda} the scaled Landau minima become material independent, in a kind of ''quasiuniversality.'' The scaled minima in N{sub OP}-dimensional order-parameter space, fall at the center and at the N{sub V} corners, of a transition-specific polyhedron inscribed in a sphere, whose radius is unity at transition. The ''polyhedra'' for the four 3D transitions are, respectively, a line, a triangle, a tetrahedron, and a hexagon. We minimize the n terms harmonic in the nonorder-parameter strains, by substituting solutions of the ''no dislocation'' St Venant compatibility constraints, and explicitly obtain power-law anisotropic, order-parameter interactions, for all transitions. In a reduced discrete-variable description, the competing minima of the Landau free energies induce unit-magnitude pseudospin vectors, with N{sub V}+1 values, pointing to the polyhedra corners and the (zero-value) center. The total scaled free energies then become Z{sub N{sub V+1}} clocklike pseudospin Hamiltonians, with temperature-dependent local Landau terms, nearest-neighbor Ginzburg couplings, and power-law St Venant interactions that drive the elastic domain-wall texturing. The scaled free energies can be used in relaxational or underdamped dynamic simulations to study ferroelastic strain textures and their dynamical evolution pathways. The pseudospin models can similarly be studied via local meanfield treatments and Monte Carlo simulations.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗