Search NASA⌕ Search

SEARCH · Search NASA

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Deformation Behavior of AM30 Magnesium Alloy

In this study, deformation behavior of AM30 magnesium alloy is investigated in the hot working regime and empirical relations are developed. Compression tests were performed in the 0.001-10 s{sup −1} strain rate range and 423-623 K temperature range to obtain the mechanical properties. The compression curves were fitted using two approaches, viz. piecewise linear fitting and a Johnson–Cook type relation. Piecewise linear fit is found to be appropriate for describing the mechanical behavior in the dynamic recrystallization (DRX) regime as compared to the proposed Johnson–Cook type relation. The Johnson–Cook type model is not able to capture the essential feature of DRX, particularly at high strain rates.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effect of Oxygen Content on Wear and Cutting Performance of AlCrON Coatings

In this work, AlCrON coatings with various oxygen contents were deposited by multi-arc-ion plating technology. The effects of oxygen content on the microstructure, mechanical properties, wear and cutting performance of AlCrON coatings were investigated. The result showed that the O contents in the AlCrON coatings increased from 0 to 8.8 wt.% by changing the O{sub 2}/N{sub 2} flow ratios during the deposition process. The AlCrON coatings mainly included fcc-CrN and fcc-AlN phases, and the Al{sub 2}O{sub 3} and Cr{sub 2}O{sub 3} were also confirmed by the XPS results. Addition of oxygen improved the adhesion strength of AlCrON coatings. The AlCrON coating with 4.0 wt.% oxygen content showed the low surface roughness, low friction coefficient and the minimum wear rate. Cutting results also showed that addition of oxygen improved the service life of AlCrON coatings under various cutting conditions. The service life of AlCrON coatings increased firstly and then decreased with increasing oxygen contents, and the AlCrON coating with 4.0 wt.% oxygen content had the maximum cutting length under various cutting conditions, which might be due to the decrease of surface roughness, increase of adhesion strength and hardness. The wear mechanism involved in cutting process included abrasive wear, adhesive wear and oxidation wear.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Effects of the Addition of Micro-amounts of Calcium on the Corrosion Resistance of Mg-0.1Mn-1.0Zn-xCa Biomaterials

Magnesium alloys have good biocompatibility and degradability, which are considered ideal characteristics of biomedical implants. However, there are few studies on the influence of the addition of micro-amounts of Ca on magnesium alloys. In this work, the effects of adding micro-amounts of Ca on the microstructure, mechanical properties, and corrosion properties of Mg-0.1Mn-1.0Zn-xCa (x = 0.1, 0.2, and 0.3 wt.%) alloys were investigated. The results reveal that the grain size of the alloy decreased and the yield strength and elongation both increased with increasing Ca concentrations. Corrosion tests in Kokubo simulated body fluid showed that the in vitro immersion rate first slowed down and then increased (6.395 → 6.283 → 6.395 mm/year) with increasing Ca concentrations. This phenomenon was due to the addition of Ca causing grain refinement, which slowed the corrosion rate and generated an Mg{sub 2}Ca phase to accelerate corrosion. The second-phase Mg{sub 2}Ca precipitated at the grain boundary and acted as a cathode, and the metal magnesium phase acted as an anode to form a primary battery, which caused corrosion of the magnesium phase and accelerated the corrosion rate.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Nickel-Coated Super-Aligned Carbon Nanotube Reinforced Copper Composite for Improved Strength and Conductivity

Nickel (Ni)-coated super-aligned carbon nanotube (SACNT) films-reinforced copper (Cu) matrix composites were fabricated by electrodeposition. The microstructure, mechanical property and electrical conductivity of the prepared composites have been studied systematically. The results show that the mechanical properties of SACNT/Cu were significantly improved by coating SACNT with Ni. When the volume fraction of SACNT is 10.0%, the tensile strength and yield strength of the composite can reach 477.8 and 295.5 MPa, respectively, corresponding to 147 and 170% improvement compared to pure Cu prepared by the same method. Meanwhile, due to the super-aligned arrangement of SACNTs and the homogeneous distribution of Ni, which is not mixing or dissolving with Cu, the conductivities of all the Ni-coated SACNT-reinforced Cu composites are above 58% IACS, which is about 4 times higher than the results in previous research. The enhancement of the strength of the SACNT/Cu composites comes from the combined contribution of load transfer and grain refinement strengthening.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Solderability of AZ31B Magnesium Alloy Coated by Copper and Strength of the Solder Joints

Magnesium alloys are promising as light materials, while their high chemical reactivity makes them difficult to be soldered. In this study, the AZ31B alloy was pretreated by zincification and coated by an electrodeposited Cu layer, and then soldered with Sn-58Bi solder in air furnace. The microstructure and properties of the AZ31B/Cu(Zn)/SnBi solder joints were characterized to evaluate the solderability of the Cu-coated Mg alloy and the influence of soldering on the Cu coating. It was found that the Cu coating is dense, and little defect exists along the Cu(Zn)/AZ31B interface. The soldering process has little negative effect on the bonding between the Cu coating and the AZ31B substrate, and the AZ31B/Cu(Zn)/SnBi solder joints of high metallurgical quality were obtained. Tensile fracture of the solder joint occurs mainly in the solder, with no peeling of the Cu coating. Under shear loading, cracks initiate inside the SnBi solder and the final fracture of the joint occurs around the Cu{sub 6}Sn{sub 5}/solder interface or along the Cu(Zn)/AZ31B interface. The tensile and shear strength of the AZ31B/Cu(Zn)/SnBi solder joints are close to that of the SnBi/Cu solder joints. It is demonstrated that the Cu-coated Mg alloy shows superior solderability and can be soldered by the Sn-based low-melting solder in air.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The Influence of Residual Stress on Fatigue Crack Growth Rates in Stainless Steel Processed by Different Additive Manufacturing Methods

The properties and microstructure of Type 304L stainless steel produced by two additive manufacturing (AM) methods—directed energy deposition (DED) and powder bed fusion (PBF)—are evaluated and compared. Localized heating and steep temperature gradients of AM processes lead to significant residual stress and distinctive microstructures, which may be process-specific and influence mechanical behavior. Test data show that materials produced by DED and PDF have small differences in tensile strengths but clear differences in residual stress and microstructural features. Measured fatigue crack growth rates (FCGRs) for cracks propagating parallel to and perpendicular to the build directions differ between the two AM materials. To separate the influences of residual stress and microstructure, K-control test procedures with decreasing and constant stress intensity factor ranges are used to measure FCGRs in the near-threshold regime (crack growth rates ≤ 1 × 10 −8 m/cycle). Residual stress is quantified by the residual stress intensity factor, K res , measured by the online crack compliance method. Correcting the FCGR data for differences in K res brings results for specimens of the two AM materials into agreement with each other and with results for wrought specimens, when the latter are corrected for crack closure. Differences in microstructure and tensile strength have an insignificant influence on FCGRs in these tests.

additive manufacturing↗
DOE OSTI2018

Nanoscale Solute Partitioning and Carbide Precipitation in a Multiphase TRIP Steel Analyzed by Atom Probe Tomography

Nanoscale solute partitioning across multiple constituent phases in a 980-grade quenched and partitioned (Q&P) steel was analyzed using atom probe tomography (APT). The Q&P process was used to increase the C content in the retained austenite phase thereby improving its stability under plastic straining. Significant carbon enrichment of austenite was measured with decreased levels of C in martensite and almost depleted C content in ferrite, supporting the C partitioning mechanism in the literature. The APT analysis of retained austenite surrounded by martensite demonstrated a higher amount of C content compared with retained austenite surrounded by the ferrite phase. Lath and discrete carbide particle precipitation was also observed inside martensite colonies, tying up C and reducing the total amount of C available for austenite stabilization. In addition, the partitioning of Mn and other minor elements was quantitatively investigated by correlating APT and SEM-EBSD. Furthermore, these techniques provide a robust methodology for analyzing nanoscale compositional partitioning in multiphase steels, TRIP steels in particular, which can be used to better explain their microstructure-mechanical property relationships.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Influences of interstitial and extrusion temperature on grain boundary segregation, Y-Ti-O nanofeatures, and mechanical properties of ferritic steels

Doping with interstitials influences the grain boundary (GB) composition of metallic alloys, enabling changes in elemental GB enrichment, grain size, and mechanical properties or even promoting nanoparticle formation. Yet, little efforts on these doping effects have been made in oxide dispersion-strengthened (ODS) steels. In this paper, by combining advanced microscopy techniques, we studied the impact of interstitial concentration and extrusion temperature on the GB structure-dependent solute segregation, Y-Ti-O nanofeatures, and mechanical properties of ferritic Fe–14Cr (wt%) ODS steels fabricated by ball milling. We found that doping with high carbon and oxygen contents causes the GB to be decorated with the interstitials and promotes nanoparticle formation along the GBs, thereby retarding capillary-driven grain coarsening. This effect performs twofold, through grain size refinement and particle hardening. For samples with low interstitial contents, altering the extrusion temperature does not significantly change the material's mechanical properties and microstructure or the nonstoichiometric chemistry of nanoparticles, which are highly stable at high temperatures. Finally and further, for all the samples, Y–Al oxides in the initial precipitation stages rapidly become coarsened at high temperatures, as Al weakens the thermal stability of nanoparticles, thereby transforming them to core-shell structures with Y-Al-rich cores and Ti-O-rich shells in the later precipitation stages.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Calcium silicate hydrate colloid at different humidities: Microstructure, deformation mechanism, and mechanical properties

Calcium silicate hydrate (C-S-H) is the main hydration product of Portland cement, while fundamental questions persist regarding its colloidal structure and water content. In this work, we developed a full atomistic C-S-H colloid model and investigated the physical and mechanical properties at different gel water concentrations. Water confined in nanometer gel pores degrades the mechanical properties of C-S-H because of its hydrolysis effect. A “ductile to brittle” transition was observed in the C-S-H colloid model with increasing gel water contents, evolving from transgranular failure to intergranular fracture. The gel water confined in nanometer-sized pores displays glassy characteristics, and it acts as a lubricant and facilitates structure distortions during the deformation. We elucidated the topology effect of the hydrogen bond network on the evolution of the viscoelasticity of C-S-H at different humidities. In conclusion, this work sheds light on the role of water in C-S-H colloids from nanostructure perspectives.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Driving rapid atomic order in MnAl via low-magnitude magnetic field annealing

Application of a mild (60 mT), uniform magnetic field during short-term thermal treatment of kinetically retained, atomically disordered (paramagnetic) ε-MnAl was found to deliver a significant ~50 % increase in the formation of L1 0 atomically ordered (ferromagnetic) τ-MnAl product phase, compared to that produced by conventional (i.e., zero-field) annealing under identical thermal conditions. The magnetic field, applied in a passive closed-circuit configuration during annealing, induced significant changes in the structural, magnetic, and phase evolution of the material. Computational results based on electronic structure calculations demonstrate that the effective magnetic susceptibility of τ-MnAl is sensitive to the orientation, rather than the magnitude, of an applied magnetic field in the vicinity of the Curie temperature. The uniaxial magnetocrystalline anisotropy of the L1 0 structure is proposed to act as a filter for selective propagation of the population of τ-MnAl variants that are favorably aligned with the applied field. In this manner, crystallographic “gridlock” is alleviated that would otherwise arise from the coexistence of multiple, energetically equivalent τ-phase variants within the parent ε-phase matrix. These results confirm that static, low-magnitude magnetic field annealing is able to accelerate L1 0 atomic ordering in the MnAl system and likely can exert similar influences in relevant magnetic systems, facilitating efficient tailoring of structure-sensitive magnetic properties for the manufacture of magnetic materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Long-term thermal aging behavior and strength reduction in a laser powder bed fusion 316H stainless steel

The long-term thermal stability of structural alloys is essential for ensuring the safe and reliable operation of nuclear reactors and other power plants. While extensive research has explored the effects of thermal aging on conventional stainless steels, the behavior of additively manufactured (AM) alloys remains less understood. This study examines the thermal aging response of laser powder bed fusion (LPBF) 316H stainless steel (SS) at temperatures ranging from 550 °C to 750 °C over durations of up to 10,000 h (approximately 1.14 years). Advanced characterization techniques, including electron microscopy and synchrotron X-ray diffraction, were used to investigate dislocation recovery and phase evolution. Based on these findings, a time-temperature-precipitation (TTP) diagram was developed for LPBF 316H SS, revealing a 10- to100-fold acceleration in precipitation kinetics compared to wrought 316H SS. A physics-informed model was calibrated using the short-term experimental data, enabling predictions of average precipitate sizes, volume fractions of M 23 C 6 and Laves phases, and changes in molybdenum solute concentration for aging up to 1 × 10⁶ h (114 years). These microstructural insights were further utilized to estimate yield strength and extrapolate strength reduction factors over the extended aging period. Despite the accelerated aging kinetics, LPBF 316H SS demonstrated superior yield strength retention compared to its wrought counterpart. In conclusion, this study establishes a framework for evaluating long-term performance using short-term experimental data and supports the accelerated qualification of AM materials for high-temperature structural applications.

Laser powder bed fusion↗
DOE OSTI2024

Grain structure and texture selection regimes in metal powder bed fusion

Additive manufacturing (AM) offers opportunities to produce complex part geometries not possible with conventional processing and in some cases even improve part performance. However, adoption has been slowed by difficulties assessing microstructure variability and there is no straightforward approach to relate processing to grain structure characteristics. In this study, datasets from AdditiveFOAM heat transport simulations of laser powder bed fusion (LPBF) are used to drive ExaCA simulations of grain structure. The GPU utilization of ExaCA and an algorithmic update for modeling melt pool overlap region solidification enabled rapid and parallel simulation across a wider range of process conditions than previously explored with cellular automata-based solidification models. A texture selection angle $θ_s$ is defined based on melt pool overlap geometry, and the range of $θ_s$ over which a commonly observed texture transition occurs in characterized AM builds was well-reproduced by ExaCA simulations over a wide range of melt pool shape, hatch spacing, and layer height. ExaCA simulations with 90 degree rotation of the scan direction on every other layer reproduced a number of trends from the AM literature including grain refinement, the dominance of layers with larger melt pools on the final grain structure, and the weakening or strengthening of texture depending on odd and even layer melt pool overlap geometry. EBSD data from a benchmark AM part is used to validate the simulated mechanism of a layer rotation-induced texture strengthening effect. Importantly, these results expand the understanding of the mechanisms for texture selection in alloys with cubic crystal symmetry and offer an approach to easily evaluate processing conditions. With this new understanding, these modeling tools will enable anticipation of previously unexpected variations in grain structure and target specific microstructures and properties.

36 MATERIALS SCIENCE↗
DOE OSTI2021

The reaction between metakaolin and limestone and its effect in porosity refinement and mechanical properties

In limestone calcined clay cements (LC{sup 3}), more hemicarboaluminate and monocarboaluminate is observed, as compared to other blended cements, from the reaction of metakaolin with limestone. In this study, it is shown that the formation of these carboaluminate phases, predominantly occurs during a “third” hydration peak, after the main alite and aluminate peaks. The influence of the metakaolin content, level of sulfate addition and the water to binder ratio on the position and magnitude of this peak were investigated. This precipitation of hemi and monocarboaluminate has a significant effect on porosity refinement and strength development. It was also observed that alumina from metakaolin can contribute to the precipitation of ettringite if sufficient sulfate is available.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Forming more and sharper sensing protrusions on graphene-based electrodes through annealing

A better understanding of the microstructure, physicochemical properties, and sensing behavior of an electrode is critical in developing quick, high sensitivity, and robust electrochemical sensors. Here, in this study, a single electrode was fabricated with self-prepared graphene ink through a drop-cast process followed with a subsequent annealing treatment. The graphene ink-based electrodes were characterized through AFM, contact angle, FTIR, impedance spectra, Raman, and SEM to understand annealing treatment effects. The dynamic response of the electrode to humidity, and vapors of ethanol, propanol, or acetone was measured using a four-point probe station in a closed chamber. The annealing treatment increased the conductivity of the electrode and improved its sensing performance by forming more and sharper protrusions on the electrode surface. These unique surface protrusions suggest that the annealed graphene ink-based electrodes hold great potential in developing high-performance electrochemical sensors.

42 ENGINEERING↗
DOE OSTI2024

Electrical property enhancement of non-heat-treatable wrought aluminum alloys using graphene additives

With growing efforts of electrification, aluminum’s role as a light-weight conductor material has become increasingly prominent. There is a critical need to improve the electrical performance of aluminum at room temperature and high operating temperatures. In this study, the effect of graphene nanoparticle additives on the electrical performance of a non-heat treatable alloy were (AA3003) explored. Graphene’s unusual structure and electronic properties were used to improve AA3003 properties. Here, in this work, the effects of graphene on the evolution of electrical properties and microstructural features have been explored on lab scale hot extruded AA3003-graphene composites. Hot pressing schedules and extrusion temperatures were varied to investigate changes in intermetallic dispersion characteristics in the presence of dispersed graphene. We measured a reduction of 10.3 % in the temperature coefficient of resistance in the AA3003 sample with 0.05 wt% graphene extruded at 400 °C, along with a maximum increase of 1.1 % in electrical conductivity at 20 °C. Increasing the hot-pressing times up to 8 hours was also found to consistently increase the electrical conductivity, due to increased precipitation of intermetallic phases. Despite being a non-heat treatable alloy, AA3003 displays interesting precipitation dynamics and grain recrystallization trends that can be modulated with varying levels of heat treatment, graphene concentrations, and hot extrusion process parameters.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The correlation between N deficiency and the mechanical properties of the Ti 2 AlNy MAX phase

The role of X deficiency on the mechanical properties of MAX phases was studied by synthesizing Ti 2 AlN through powder metallurgy in stoichiometric and sub/extra-stoichiometric nitrogen compositions. XRD analyses and ab initio calculations indicate that nitrogen vacancies result in a lattice contraction predominantly along the c-axis. The elastic moduli and intrinsic hardness of substoichiometric Ti 2 AlN 0.9 measured from nanoindentation tests are shown to be slightly smaller than that of Ti 2 AlN. The key mechanical indexes, bulk (B), shear (G) and Young’s (E) moduli as well as the hardness variation are calculated in density functional theory, and show different responses depending on the concentration of N vacancies. Overall, this joint experimental and theoretical study provides a full understanding of the energetics, chemical bonding, electronic structure, and mechanics of the N deficient MAX phases which would increase the application of nitride ceramics.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Review of in situ process monitoring for metal hybrid directed energy deposition

Hybrid manufacturing, or the combination of additive and subtractive manufacturing within a single build volume is transforming the way products are being fabricated. Additive manufacturing confers unprecedented freedom of design and reduced material usage while enabling serial customization. Subtractive manufacturing provides superior surface finish and improved dimensional accuracies. Interwoven, these two digital manufacturing paradigms are enabling the rapid manufacturing of complex, highly accurate, and customized geometries in a diversity of high-performance alloys. In situ monitoring, heavily relied upon in either additive or subtractive, becomes even more crucial with the interplay of the two processes in a single combined build sequence. Moreover, challenges that do not exist in either process alone can now have a dramatic impact on final part quality: (1) a large amount of heat is generated during additive manufacturing deposition, which is primarily dissipated into the machine tooling and impacts accuracy by deforming the material and causing misaligned machining; (2) microstructure, mechanical properties, and residual stresses are the result of the complex thermal histories generated by additive manufacturing and can impact subsequent cutting performance. This comprehensive review considers previous research in monitoring and providing closed-loop control in both additive and subtractive manufacturing separately and then considers the implications of the effectiveness of these monitoring techniques when additive and subtractive processes are integrated together.

36 MATERIALS SCIENCE↗