Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES, FLAT - STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Surface pressure fluctuations in hypersonic turbulent boundary layers

The surface pressure fluctuations on a flat plate model at hypersonic Mach numbers of 5.2, 7.4 and 10.4 with an attached turbulent boundary layer were measured using flush mounted small piezoelectric sensors. A high frequency resolution of the pressure field was achieved using specially designed small piezoelectric sensors that had a good frequency response well above 300 KHz. The RMS pressures and non-dimensional energy spectra for all above Mach numbers are presented. The convective velocities, obtained from space time correlation considerations are equal to 0.7 U sub infinity. The results indicate the RMS pressures vary from 5 to 25 percent of the mean static pressures. The ratios of RMS pressure to dynamic pressure are less than the universally accepted subsonic value of 6 x 10/3. The ratio decreases in value as the Mach number or the dynamic pressure is increased. The ratio of RMS pressure to wall shear for Mach number 7.4 satisfies one smaller than or equal to p/tau sub w smaller than or equal to three.

Raman, K. R.↗

Correaltion of full-scale drag predictions with flight measurements on the C-141A aircraft. Phase 2: Wind tunnel test, analysis, and prediction techniques. Volume 1: Drag predictions, wind tunnel data analysis and correlation

The degree of cruise drag correlation on the C-141A aircraft is determined between predictions based on wind tunnel test data, and flight test results. An analysis of wind tunnel tests on a 0.0275 scale model at Reynolds number up to 3.05 x 1 million/MAC is reported. Model support interference corrections are evaluated through a series of tests, and fully corrected model data are analyzed to provide details on model component interference factors. It is shown that predicted minimum profile drag for the complete configuration agrees within 0.75% of flight test data, using a wind tunnel extrapolation method based on flat plate skin friction and component shape factors. An alternative method of extrapolation, based on computed profile drag from a subsonic viscous theory, results in a prediction four percent lower than flight test data.

Macwilkinson, D. G.↗

Venting characteristics of gaseous helium and nitrogen discharging into a free stream at Mach numbers from 0.60 to 1.57

An experimental investigation was conducted in the Lewis Research Center 8- by 6-Foot Supersonic Wind Tunnel to compare the effects on discharge coefficient of venting gaseous helium and gaseous nitrogen into a free stream. The test was conducted from Mach 0.06 to 1.57 with the vent mounted in a flat plate. The plate was strut mounted to the tunnel ceiling and at a 0 angle of attack. The gases were discharged from a plenum chamber through a 2.54-centimeter (1.00-in.) diameter vent. The ratio of local static pressure to plenum pressure was varied from 0.51 to 0.975. The ratio of boundary layer thickness to vent diameter varied from a maximum of 1.34 at Mach 0.60 to a minimum of 0.55 at Mach 1.37.

Johns, A. L.↗

Thermal performance of multilayer insulations

Experimental and analytical studies were conducted in order to extend previous knowledge of the thermal performance and gas evacuation characteristics of three selected multilayer insulation (MLI) composites. Flat plate calorimeter heat flux measurements were obtained for 20- and 80- shield specimens using three representative layer densities over boundary temperatures ranging from 39 K (70 R) to 389 K (700 R). Laboratory gas evacuation tests were performed on representative specimens of each MLI composite after initially purging them with helium, nitrogen, or argon gases. In these tests, the specimens were maintained at temperatures between 128 K (230 R) and 300 K (540 R). Based on the results of the laboratory-scale tests, a composite MLI system consisting of 112 unperforated, double-aluminized Mylar reflective shields and 113 water preconditioned silk net spacer pairs was fabricated and installed on a 1.22-m-(4-ft-) diameter calorimeter tank.

Keller, C. W.↗

The development of a solar-powered residential heating and cooling system

Efforts to demonstrate the engineering feasibility of utilizing solar power for residential heating and cooling are described. These efforts were concentrated on the analysis, design, and test of a full-scale demonstration system which is currently under construction at the National Aeronautics and Space Administration, Marshall Space Flight Center, Huntsville, Alabama. The basic solar heating and cooling system under development utilizes a flat plate solar energy collector, a large water tank for thermal energy storage, heat exchangers for space heating and water heating, and an absorption cycle air conditioner for space cooling.

Source record↗

Computer program for calculation of real gas turbulent boundary layers with variable edge entropy

A user's manual for a computer program which calculates real gas turbulent boundary layers with variable edge entropy on a blunt cone or flat plate at zero angle of attack is presented. An integral method is used. The method includes the effect of real gas in thermodynamic equilibrium and variable edge entropy. A modified Crocco enthalpy velocity relationship is used for the enthalpy profiles and an empirical correlation of the N-power law profile is used for the velocity profile. The skin-friction-coefficient expressions of Spalding and Chi and Van Driest are used in the solution of the momentum equation and in the heat-transfer predictions that use several modified forms of Reynolds analogy.

Boney, L. R.↗

Effect of ratio of wall boundary layer thickness to jet diameter on mixing of a normal hydrogen jet in a supersonic stream

A preliminary experimental program was conducted to determine the effect of the ratio of the free-stream boundary-layer thickness to jet diameter on the secondary jet penetration and mixing rate. Tests were conducted on a flat plate in a Mach number 4.05 airflow with sonic injection of hydrogen normal to the free-stream direction from circular underexpanded injectors. The ratio of boundary-layer thickness to jet diameter ranged from 1.25 to 6.5. Previous correlations of mixing performance were modified to account for the effect of the ratio of boundary-layer thickness to jet diameter.

Mcclinton, C. R.↗

The use of COD and plastic instability in crack propagation and arrest in shells

The initiation, growth, and possible arrest of fracture in cylindrical shells containing initial defects are dealt with. For those defects which may be approximated by a part-through semi-elliptic surface crack which is sufficiently shallow so that part of the net ligament in the plane of the crack is still elastic, the existing flat plate solution is modified to take into account the shell curvature effect as well as the effect of the thickness and the small scale plastic deformations. The problem of large defects is then considered under the assumptions that the defect may be approximated by a relatively deep meridional part-through surface crack and the net ligament through the shell wall is fully yielded. The results given are based on an 8th order bending theory of shallow shells using a conventional plastic strip model to account for the plastic deformations around the crack border.

Erdogan, F.↗

Low-cost, air mass 2 solar simulator

A low cost air mass 2 solar simulator for testing flat-plate solar collectors was developed and operated at Lewis. Total cost was less than $10,800/sq m ($1000/sq ft). It consists of an array of 143 tungsten-halogen 300-watt lamps, each having integral dichroic coated reflectors. A second array of 143 respective hexagonal-shaped plastic Fresnel lenses are located approximately 1 focal length from the lamps. The simulator will produce a uniform collimated beam covering an area of 1.2 by 1.2m(4 by 4 ft). Design features, construction details, and component costs are given, as well as measured results on a 12-lamp prototype.

Yass, K.↗

Flush-mounted antennas radiating on aircraft type surfaces

The roll plane radiation patterns of on-aircraft antennas are analyzed using high frequency solutions. This is a basic study of aircraft-antenna pattern performance in which the aircraft is modelled in its most basic form. The fuselage is assumed to be a perfectly conducting elliptic cylinder with the antennas mounted near the top or bottom. The wings are simulated by arbitrarily many sided flat plates.

Burnside, W. D.↗

Engineering prediction of turbulent skin friction and heat transfer in high-speed flow

A large collection of experimental turbulent-skin-friction and heat-transfer data for flat plates and cones was used to determine the most accurate of six of the most popular engineering-prediction methods; the data represent a Mach number range from 4 to 13 and ratio of wall to total temperature ranging from 0.1 to 0.7. The Spalding and Chi method incorporating virtual-origin concepts was found to be the best prediction method for Mach numbers less than 10; the limited experimental data for Mach numbers greater than 10 were not well predicted by any of the engineering methods except the Coles method.

Cary, A. M., Jr.↗

Roll plane analysis of on-aircraft antennas

The roll plane radiation patterns of on-aircraft antennas are analyzed using high frequency solutions. This is a basic study of aircraft-antenna pattern performance in which the aircraft is modelled in its most basic form. The fuselage is assumed to be a perfectly conducting elliptic cylinder with the antennas mounted near the top or bottom. The wings are simulated by arbitrarily many sided flat plates and the engines by circular cylinders. The patterns in each case verified by measured results taken on simple models as well as scale models of actual aircraft.

Burnside, W. D.↗

Analysis of impingement heat transfer for two parallel liquid-metal slot jets

An analytical method is developed for determining heat transfer by impinging liquid-metal slot jets. The method involves mapping the jet flow region, which is bounded by free streamlines, into a potential plane where it becomes a uniform flow in a channel of constant width. The energy equation is transformed into potential plane coordinates and is solved in the channel flow region. Conformal mapping is then used to transform the solution back into the physical plane and obtain the desired heat-transfer characteristics. The analysis given here determines the heat-transfer characteristics for two parallel liquid-metal slot jets impinging normally against a uniformly heated flat plate. The liquid-metal assumptions are made that the jets are inviscid and that molecular conduction is dominating heat diffusion. Wall temperature distributions along the heated plate are obtained as a function of spacing between the jets and the jet Peclet number.

Siegel, R.↗

Theory of discrete vortex noise

A solution is obtained for the noise induced by vortex shedding from the trailing edge of a semiinfinite flat plate. The method of solution for the potential flow is based on a procedure whereby an inner incompressible flow is matched to an outer acoustic field. Acoustic wave fronts are calculated and compared qualitatively with schlieren photographs of similar flows. The acoustic directivity pattern is obtained, and the extreme sensitivity of this parameter to the incompressible flow near the trailing edge of the plate is investigated.

Davis, S. S.↗

On the application of linear stability theory to the problem of supersonic boundary-layer transition

Linear stability theory is used to calculate the amplitude ratio of constant-frequency disturbances as a function of Reynolds number for insulated and cooled-wall flat-plate boundary layers between Mach numbers 1.3 and 5.8. The growth curves are used to examine the consequences of using a fixed amplitude of the most unstable frequency as a transition criterion. The effect of free-stream Mach number on insulated-wall boundary layers is calculated, assuming that the initial disturbance level is constant, is proportional to the square of the free-stream Mach number and to the square root of the energy density of the one-dimensional power spectra of free-stream disturbances measured in supersonic wind tunnels.

Mack, L. M.↗

Thermoacoustic convection of fluids in low gravity

The heat flow in a confined perfect gas in low gravity is investigated, including the effects of conduction and thermal convection. Buoyancy-driven flow is neglected, due to the low-gravity environment, but the effect of thermoacoustic motion due to fluid compressibility is included. One-dimensional mathematical models are constructed from the conservation equations for a compressible, viscous, heat-conducting fluid. A conservative, time-dependent finite-difference method is used to generate numerical solutions on a digital computer. Problems for flat plates and cylindrical segments are solved for specified thermal boundary conditions. Numerical results are given which indicate that thermoacoustic convection can significantly increase the transient heat flow over conduction model predictions for cases where a confined gas is rapidly heated.

Spradley, L. W.↗

Application of an invariant second-order closure model to compressible turbulent shear layers

A second-order closure model for two-dimensional, compressible shear flows is investigated using the invariant modeling technique developed by Donaldson. The invariant model parameters were originally selected by comparison of model predictions with critical experimental data on basic incompressible flows. Additional modeling for compressible flows has been introduced. A number of different shear flows such as the free shear layer, flat plate boundary layer and a simulation of the mixing region of a chemical laser are computed. The model is consistent with first-order closure turbulence models for equilibrium flows and is further capable of predicting nonequilibrium flows that cannot be correctly solved by eddy viscosity models. The results are in generally good agreement with experimental measurements but suggest the need for inclusion of a Mach number dependent model of the pressure diffusion terms in order to adequately represent high speed compressible flows.

Varma, A. K.↗

Raman scattering applied to hypersonic air flow

The Raman scattering technique was applied to measure the local static temperature and gas number density over a sharp-edge flat-plate model in a Mach 5 nozzle of the Langley nozzle test chamber with air as the test gas. The angle of attack varied from -5 to 15 deg, and the stagnation temperature varied from 317 to 442 K, with stagnation pressures ranging from 170 kN to 2.8 MN/sq m. The measured values of static temperature and density ranged from 60 to 100 K and from 0.03 to 0.8 kg/cu m, respectively. A comparison with calculated values based on static pressure measurements along the model shows that the Raman scattering technique is a viable measurement method in applications to high-speed three-dimensional flows.

Hillard, M. E., Jr.↗