Search NASA⌕ Search

SEARCH · Search NASA

Results for “catalyst loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

NiAu Single Atom Alloys for the Non-oxidative Dehydrogenation of Ethanol to Acetaldehyde and Hydrogen

Gold is examined here as an alternative to copper for the selective dehydrogenation of ethanol to acetaldehyde and hydrogen. Despite its high selectivity, gold is only active at temperatures higher than 250 °C for this reaction. We demonstrate that addition of a small amount of Ni on either supported or unsupported Au surfaces induces resistance to sintering, along with a beneficial effect on the catalytic activity. NiAu alloys prepared here with Ni as the minority component to the limit of atomic dispersion in the gold surfaces, catalyze the reaction beginning below 150 °C. A significant decrease of the apparent activation energy from 96 ± 3 kJ/mol for the monometallic Au to 59 ± 5 kJ/mol for the alloy was found. The Ni dispersion and concentration as a function of gas environment was followed by in situ DRIFTS and by XPS. The stability of the catalyst morphology was investigated through post-reaction microscopy imaging and long-term stability tests under reaction conditions. As shown via dynamic reaction experiments, acetaldehyde and H 2 were selectively produced up to 280 °C. A small drop of selectivity at higher temperatures is attributed to the formation of Ni clusters, as proven by CO-DRIFTS on the used sample. Comparison with samples of higher Ni loading, where Ni clusters are formed, clearly shows that they catalyze the undesired full decomposition of ethanol to CO, CH 4 , and H 2 .

36 MATERIALS SCIENCE↗

Understanding how single-atom site density drives the performance and durability of PGM-free Fe–N–C cathodes in anion exchange membrane fuel cells

One of the most important needs for the future of low-cost fuel cells is the development of highly active platinum group metal (PGM)-free catalysts. For the oxygen reduction reaction, Fe–N–C materials have been widely studied in both acid and alkaline media. However, reported catalysts in the literature show quite different intrinsic activity and in-cell performance, despite similar synthesis routes and precursors. Here, two types of Fe–N–C are prepared from the same precursor and procedure – the main difference is how the precursor was handled prior to use. It is shown that in one case Fe overwhelmingly existed as highly active single-metal atoms in FeN4 coordination (preferred), while in the other case large Fe particles coexisting with few single metal atoms were obtained. As a result, there were drastic differences in the catalyst structure, activity, and especially in their performance in an operating anion exchange membrane fuel cell (AEMFC). Additionally, it is shown that catalyst layers created from single-atom-dominated Fe–N–C can have excellent performance and durability in an AEMFC using H 2 /O 2 reacting gases, achieving a peak power density of 1.8 W cm -2 – comparable to similar AEMFCs with a Pt/C cathode – and being able to operate stably for more than 100 h. Finally, the Fe–N–C cathode was paired with a low-loading PtRu/C anode electrode to create AEMFCs (on H 2 /O 2 ) with a total PGM loading of only 0.135 mg cm -2 (0.090 mg Pt cm -2 ) that was able to achieve a very high specific power of 8.4 W mg PGM -1 (12.6 W mg Pt< sup>-1 ).

36 MATERIALS SCIENCE↗

Palladium–platinum core-shell icosahedra with substantially enhanced activity and durability towards oxygen reduction

Conformal deposition of platinum as ultrathin shells on facet-controlled palladium nanocrystals offers a great opportunity to enhance the catalytic performance while reducing its loading. Here we report such a system based on palladium icosahedra. Owing to lateral confinement imposed by twin boundaries and thus vertical relaxation only, the platinum overlayers evolve into a corrugated structure under compressive strain. For the core-shell nanocrystals with an average of 2.7 platinum overlayers, their specific and platinum mass activities towards oxygen reduction are enhanced by eight- and sevenfold, respectively, relative to a commercial catalyst. Density functional theory calculations indicate that the enhancement can be attributed to the weakened binding of hydroxyl to the compressed platinum surface supported on palladium. After 10,000 testing cycles, the mass activity of the core-shell nanocrystals is still four times higher than the commercial catalyst. Ultimately, these results demonstrate an effective approach to the development of electrocatalysts with greatly enhanced activity and durability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Advanced CO 2 Capture Technology for Low Rank Coal IGCC System

The overall objective of the project is to demonstrate the technical and economic viability of a new Integrated Gasification Combined Cycle (IGCC) power plant designed to efficiently process low rank coals. The plant uses an integrated CO 2 scrubber/Water Gas Shift (WGS) catalyst to capture over90 percent capture of the CO 2 emissions, while providing a significantly lower cost of electricity (COE) than a similar plant with conventional cold gas cleanup system based on Selexol TM technology and 90 percent carbon capture. TDA’s system uses a high temperature physical adsorbent capable of removing CO 2 above the dew point of the synthesis gas and a commercial WGS catalyst that can effectively convert CO in The overall objective of the project is to demonstrate the technical and economic viability of a new Integrated Gasification Combined Cycle (IGCC) power plant designed to efficiently process low rank coals. The plant uses an integrated CO 2 scrubber/Water Gas Shift (WGS) catalyst to capture over90 percent capture of the CO 2 emissions, while providing a significantly lower cost of electricity (COE) than a similar plant with conventional cold gas cleanup system based on Selexol TM technology and 90 percent carbon capture. TDA’s system uses a high temperature physical adsorbent capable of removing CO 2 above the dew point of the synthesis gas and a commercial WGS catalyst that can effectively convert CO in bituminous coal the net plant efficiency is about 2.4 percentage points higher than an Integrated Gasification Combined Cycle (IGCC) plant equipped with Selexol TM to capture CO 2 . We also previously completed two successful field demonstrations: one at the National Carbon Capture Center (Southern- Wilsonville, AL) in 2011, and a second demonstration in fall of 2012 at the Wabash River IGCC plant (Terra Haute, IN). In this project, we first optimized the sorbent to catalyst ratio used in the combined WGS and CO 2 capture process and confirmed the technical feasibility in bench-scale experiments. In these tests, we did not observe any CO breakthrough both during adsorption and desorption steps indicating that there is complete conversion of CO to CO 2 and H 2 . The overall CO conversions above 90 percent were observed. The sorbent achieved a total CO 2 loading of 7.82 percent wt. of which 5.68 percent is from conversion of CO into CO 2 . The results of the system analysis suggest that the TDA combined shift and high temperature PSA-based Warm Gas Clean-up technology can make a substantial improvement in the IGCC plant thermal performance for a plant designed to achieve near zero emissions (including greater than 90 percent carbon capture). The capital expenses are also expected to be lower than those of Selexol. The higher net plant efficiency and lower capital and operating costs result in substantial reduction in the COE for the IGCC plant equipped with the TDA combined shift and high temperature PSA-based carbon capture system.

01 COAL, LIGNITE, AND PEAT↗

Promotional Effects of In on Non-Oxidative Methane Transformation Over Mo-ZSM-5

In this paper, we present a new class of catalysts, InMo-ZSM- 5 , which can be prepared by indium impregnation of Mo-ZSM- 5 . The incorporation of indium dramatically decreases coke formation during methane dehydroaromatization. The benzene and C 2 hydrocarbons selectivity among total hydrocarbons over InMo-ZSM- 5 remains comparable to that of Mo-ZSM- 5 despite reduced methane conversion due to decreased coke formation. We found 1 wt% indium to be optimal loading for reducing coke selectivity to half that of Mo-ZSM- 5 . Characterization methods were not helpful in discerning the interaction of In with Mo but experiments with bimetallic 1In2Mo-ZSM- 5 and mechanical mixture 1In+2Mo-ZSM- 5 suggest that In and Mo need to be in close proximity to suppress coke formation. Finally, this is supported by temperature programmed reduction experiments which show that In incorporation leads to lower Mo reduction temperature in In2Mo-ZMS- 5 .

36 MATERIALS SCIENCE↗

Photocatalytic degradation of gaseous toluene over hollow “spindle-like” α-Fe{sub 2}O{sub 3} loaded with Ag

Highlights: ► Hollow α-Fe{sub 2}O{sub 3} spindle-shaped microparticles were prepared for Ag support. ► The hollow α-Fe{sub 2}O{sub 3} and Ag/α-Fe{sub 2}O{sub 3} materials were used to degrade gaseous toluene. ► Complete degradation of toluene occurred on the Ag/α-Fe{sub 2}O{sub 3} surface. -- Abstract: In this work, hollow “spindle-like” α-Fe{sub 2}O{sub 3} nanoparticles were synthesized by a hydrothermal route. The Ag/α-Fe{sub 2}O{sub 3} catalyst was prepared based on the spindle-shaped α-Fe{sub 2}O{sub 3} with CTAB as the surfactant, which showed excellent photoelectric property and photocatalytic activity. The structural properties of these samples were systematically investigated by X-ray powder diffraction, scanning electronic microscopy, transmission electronic microscopy, energy-dispersive X-ray spectra, and UV–Vis diffuse reflectance spectroscopy techniques. The photo-induced charge separation in the samples was demonstrated by surface photovoltage measurement. The photocatalytic performances of the Ag/α-Fe{sub 2}O{sub 3} and α-Fe{sub 2}O{sub 3} samples were comparatively studied in the degradation of toluene under xenon lamp irradiation by in situ FTIR spectroscopy. Benzaldehyde and benzoic acid species could be observed on the α-Fe{sub 2}O{sub 3} surface rather than Ag/α-Fe{sub 2}O{sub 3} surface. The results indicate that the Ag/α-Fe{sub 2}O{sub 3} sample exhibited higher photocatalytic efficiency.

36 MATERIALS SCIENCE↗

Establishment of an Environmental Control Technology Laboratory with a Circulating Fluidized-Bed Combustion System

On February 14, 2002, President Bush announced the Clear Skies Initiative, a legislative proposal to control the emissions of nitrogen oxides (NO{sub x}), sulfur dioxide (SO{sub 2}), and mercury from power plants. In response to this initiative, the National Energy Technology Laboratory organized a Combustion Technology University Alliance and hosted a Solid Fuel Combustion Technology Alliance Workshop. The workshop identified multi-pollutant control; improved sorbents and catalysts; mercury monitoring and capture; and improved understanding of the underlying reaction chemistry occurring during combustion as the most pressing research needs related to controlling environmental emissions from fossil-fueled power plants. The Environmental Control Technology Laboratory will help meet these challenges and offer solutions for problems associated with emissions from fossil-fueled power plants. The goal of this project was to develop the capability and technology database needed to support municipal, regional, and national electric power generating facilities to improve the efficiency of operation and solve operational and environmental problems. In order to effectively provide the scientific data and the methodologies required to address these issues, the project included the following aspects: (1) Establishing an Environmental Control Technology Laboratory using a laboratory-scale, simulated fluidized-bed combustion (FBC) system; (2) Designing, constructing, and operating a bench-scale (0.6 MW{sub th}), circulating fluidized-bed combustion (CFBC) system as the main component of the Environmental Control Technology Laboratory; (3) Developing a combustion technology for co-firing municipal solid waste (MSW), agricultural waste, and refuse-derived fuel (RDF) with high sulfur coals; (4) Developing a control strategy for gaseous emissions, including NO{sub x}, SO{sub 2}, organic compounds, and heavy metals; and (5) Developing new mercury capturing sorbents and new particulate filtration technologies. Major tasks during this period of the funded project's timeframe included: (1) Conducting pretests on a laboratory-scale simulated FBC system; (2) Completing detailed design of the bench-scale CFBC system; (3) Contracting potential bidders to fabricate of the component parts of CFBC system; (4) Assembling CFBC parts and integrating system; (5) Resolving problems identified during pretests; (6) Testing with available Powder River Basin (PRB) coal and co-firing of PRB coal with first wood pallet and then chicken wastes; and (7) Tuning of CFBC load. Following construction system and start-up of this 0.6 MW CFBC system, a variety of combustion tests using a wide range of fuels (high-sulfur coals, low-rank coals, MSW, agricultural waste, and RDF) under varying conditions were performed to analyze and monitor air pollutant emissions. Data for atmospheric pollutants and the methodologies required to reduce pollutant emissions were provided. Integration with a selective catalytic reduction (SCR) slipstream unit did mimic the effect of flue gas composition, including trace metals, on the performance of the SCR catalyst to be investigated. In addition, the following activities were also conducted: (1) Developed advanced mercury oxidant and adsorption additives; (2) Performed laboratory-scale tests on oxygen-fuel combustion and chemical looping combustion; and (3) Conducted statistical analysis of mercury emissions in a full-scale CFBC system.

01 COAL, LIGNITE, AND PEAT↗

Method for conversion of diols to olefin products

A method for converting a diol in solution to an olefin fraction, the method comprising: (i) reacting a diol of the formula HO—R—OH in solution with a carbonyl-containing molecule of the formula: in the presence of an acid catalyst to result in a dioxolane molecule of the formula: wherein R is a hydrocarbon linker containing 1-12 carbon atoms, and R 1 and R 2 are independently selected from hydrogen atom and hydrocarbon groups containing 1-12 carbon atoms, wherein R 1 and R 2 optionally interconnect; (ii) removing the dioxolane molecule from the solution by phase separation; and (iii) contacting the dioxolane molecule with a metal-loaded zeolite at a temperature of 100-500° C. to convert the dioxolane molecule to an olefin fraction.

Li, Zhenglong↗

Co‐Electrolysis of CO 2 and H 2 O to Syngas on Bimetallic Pd x Cu 1‐ x Catalysts for Tandem Thermochemical Conversion to Carbon Nanofibers

Electrification of chemical production using renewable energy and abundant feedstocks offers a promising pathway for decarbonizing the chemical industry. Current efforts on CO 2 valorization largely focus on making chemicals and fuels. Here, to help achieve net-negative emissions through long-term carbon storage, this study aims to develop efficient electrocatalysts for a tandem electrochemical-thermochemical process to convert CO 2 into carbon nanofibers (CNFs). CO 2 and water are first electrochemically reduced in a membrane electrode assembly (MEA) electrolyzer to produce syngas (CO + H 2 ), which is subsequently fed into a thermochemical packed bed reactor to facilitate CNF growth. This work systematically evaluated Pd x Cu 1-x bimetallic electrocatalysts to assess the effect of Pd–Cu alloying on enhancing syngas production while reducing Pd loading. Transmission electron microscopy and Raman spectroscopy confirmed the formation of high-purity, crystalline CNFs, regardless of the syngas composition from the MEA. In situ X-ray absorption spectroscopy and X-ray diffraction measurements revealed that increasing Cu content in the Pd x Cu 1-x alloy progressively inhibited palladium hydride formation, consistent with DFT calculations on the stability of Pd x Cu 1-x under reducing electrochemical potentials.

58 GEOSCIENCES↗

Intercalative Redox Tuning for Cu/Li x Mn 2 O 4 -Catalyzed Oxidative Alkyne Coupling

Modulation of heterogeneous catalyst structure is ubiquitous within efforts to improve catalytic activity and selectivity at the molecular level. Herein, manganese oxide (MnO 2 ) is employed as a continuously tunable catalyst support through increasing extent of lithium intercalation and reduced surface potential. Oxidative grafting of an organocopper complex onto various lithium manganese oxides (Li x Mn 2 O 4 , x = 0-2.1) produced divalent and monovalent copper species on the partially reduced (0 ≤ x ≤ 1.2) and fully reduced (x = 2.1) surfaces, respectively, as determined by X-ray absorption fine structure (XAFS) analysis. In this study, the resultant materials are catalytically active for the oxidative coupling of terminal alkynes, with steady-state reaction rate data of oxidative propyne dimerization (200 °C, 0.6-2.4 kPa propyne, 2.4-9.9 kPa O 2 ) indicating that complete support lithiation (Li 2.1 Mn 2 O 4 ) provides increased catalytic performance and renders reoxidation steps less kinetically demanding compared to the unreduced parent material. Enacting a dual site (Cu and MnO x ) kinetic model can account for dimerization rates measured over Cu/Li 2.1 Mn 2 O 4 under various reactant concentrations, copper loadings, and surface coverages, providing supporting evidence for the synergistic role of the metal and support in facilitating the coupling reaction. Overall, results presented here provide an extension for general strategies of systematically controlling catalytic structure and function through lithium reduction of bulk oxides and subsequent electronic modulation of the metals supported thereon.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Preparation of carbon supported cobalt by electrostatic adsorption of [Co(NH[subscript 3])[subscript 6]]Cl[subscript 3]

Our previous paper [L. D'Souza, L. Jiao, J.R. Regalbuto, J.T. Miller, A.J. Kropf, J. Catal. 248 (2007) 165] presented the synthesis of cobalt catalysts on carbon (Timrex) and silica supports by strong electrostatic adsorption (SEA), using a cobalt hexaamine chloride ([Co(NH{sub 3}){sub 6}]Cl{sub 3}, CoHA) precursor. The CoHA undergoes reductive deammination in an uncontrolled manner in the presence of NaOH and adsorbs as Co{sub 3}O{sub 4} on carbon with broad size distribution. The present paper extends these studies toward the end of synthesizing well-dispersed Co oxide particles in a narrow size range on carbon supports using NH{sub 4}OH. Cobalt uptake versus pH was determined in NH{sub 4}OH and NaOH basified solutions over a number of carbons with varying point of zero charge (PZC). The resulting materials were characterized by ICP, powder XRD, XAS, TPR and STEM. CoHA in the presence of NH{sub 4}OH adsorbs as well dispersed as CoO, Co{sub 3}O{sub 4} and Co(OH){sub 4}{sup 2-} depending upon the pH of the adsorption solution. These phases were undetectable by powder XRD and STEM Z-contrast imaging, but could be identified by XAS. Additionally, non-adsorbed CoHA complexes underwent transformation to [Co(NH{sub 3}){sub 5}Cl]Cl{sub 2} at pH > 11 in solution. After calcinations of 250 C, particle sizes of Co{sub 3}O{sub 4} range from 20-50 {angstrom} from NH{sub 4}OH and 50-200 {angstrom} from NaOH. Maximum metal uptake was approximately 3.3 and 2.7 {micro}mol/m{sup 2} in presence of NaOH and NH{sub 4}OH, respectively. The SEA method of preparation was compared with incipient wetness impregnation (IWI) of Co(NO{sub 3}){sub 2}{sm_bullet}6H{sub 2}O; this method yields Co{sub 3}O{sub 4} particles after 250 C calcinations which are almost as small or in one case, smaller than the calcined SEA samples. Higher metal loadings can be achieved by the SEA method by successive adsorption steps with a little variation in particle size and distribution. However, the main advantage of SEA is in forming mono- or submonolayer of different Co oxide phases on carbon surface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigating the Surface Structure of γ-Al 2 O 3 Supported WO X Catalysts by High Field 27 Al MAS NMR and Electronic Structure Calculations

The metal-support interaction in γ-Al2O3 supported WOX catalysts is investigated by a combination of high field quantitative single pulse (SP) 27Al MAS NMR spectroscopy, 2D MQMAS, 1H-27Al CP/MAS, and electronic structure calculations. NMR allows the observation of at least seven different Al sites, including a pentahedral Al site, three different tetrahedral Al sites, and three octahedral Al sites. It is found that the penta-coordinated Al (AlP) site density decreases monotonically with an increased WOX loading while the octahedral Al (AlO) site density increases concurrently. This suggests that the Alp sites are the preferred surface anchoring positions for the WOX species. Importantly, the AlP site isotropic chemical shift observed for the unsupported γ-Al2O3 at about 38 ppm migrates into the octahedral region with a new isotropic chemical shift value appearing near 7 ppm when the Alp site is anchored by WOX species. Density functional theory (DFT) computational modeling of the NMR parameters on proposed cluster models is carried out to accurately interpret the dramatic chemical shift changes from which the detailed anchoring mechanisms are obtained. It is found that tungsten dimers and monomers are the preferred supported surface species on γ-Al2O3, wherein one monomeric and several dimeric structures are identified as the most likely surface anchoring structures.

27Al MAS NMR↗

Load Expansion of Stoichiometric HCCI Using Spark Assist and Hydraulic Valve Actuation

A spark-assist homogeneous charge compression ignition (SA-HCCI) operating strategy is presented here that allows for stoichiometric combustion from 1000-3000 rpm, and at loads as high as 750 kPa net IMEP. A single cylinder gasoline engine equipped with direct fuel injection and fully variable hydraulic valve actuation (HVA) is used for this experimental study. The HVA system enables negative valve overlap (NVO) valve timing for hot internal EGR. Spark-assist stabilizes combustion over a wide range of engine speeds and loads, and allows for stoichiometric operation at all conditions. Characteristics of both spark-ignited combustion and HCCI are present, with combustion analysis showing a distinctive spark ignited phase of combustion, followed by a much more rapid HCCI combustion phase. At high load, the maximum pressure rise rate is controlled by a combination of spark timing and retarding the intake valve closing angle. The latter reduces the effective compression ratio, and therefore the compressive temperatures, allowing the high load limit of the operating range to be expanded. The SA-HCCI operating strategy exhibits improved thermal efficiency at most operating conditions, with fuel consumption improvements up to 9% realized at light engine loads. The SA-HCCI operating strategy presented here does not provide an efficiency advantage at all operating points compared to SI combustion; a decrease was observed at the highest speed and at loads above 500 kPa net IMEP. At light engine loads the majority of the heat release takes place during the HCCI phase of the heat release, and as such the NOx emissions are very low and are similar to levels observed in pure HCCI. At higher loads, a larger portion of the heat release takes place during the spark ignited phase of combustion, which produces NOx emissions that are much higher than is typically associated with HCCI, but still represent a decrease from conventional SI combustion. By limiting the fuel/air mixture to stoichiometric conditions, the higher NOx emissions do not represent an implementation barrier to this strategy because compatibility is maintained with very effective conventional 3-way catalysts.

33 ADVANCED PROPULSION SYSTEMS↗

Development Of Sustainable Biobased Products And Bioenergy In Cooperation With The Midwest Consortium For Sustainable Biobased Products And Energy

Collaborative efforts of Midwest Consortium have been put forth to add value to distiller's grains by further processing them into fermentable sugars, ethanol, and a protein rich co-product consistent with a pathway to a biorenewables industry (Schell et al, 2008). These studies were recently published in the enclosed special edition (Volume 99, Issue 12) of Bioresource Technology journal. Part of them have demonstrated the utilization of distillers grains as additional feedstock for increased ethanol production in the current dry grind process (Kim et al., 2008a, b; Dien et al.,2008, Ladisch et al., 2008a, b). Results showed that both liquid hot water (LHW) pretreatment and ammonia fiber expansion (AFEX) were effective for enhancing digestibility of distiller's grains. Enzymatic digestion of distiller's grains resulted in more than 90% glucose yield under standard assay conditions, although the yield tends to drop as the concentration of dry solids increases. Simulated process mass balances estimated that hydrolysis and fermentation of distillers grains can increase the ethanol yield by 14% in the current dry milling process (Kim et al., 2008c). Resulting co-products from the modified process are richer in protein and oil contents than conventional distiller's grains, as determined both experimentally and computationally. Other research topics in the special edition include water solubilization of DDGS by transesterification reaction with phosphite esters (Oshel el al., 2008) to improve reactivity of the DDGS to enzymes, hydrolysis of soluble oligomers derived from DDGS using functionalized mesoporous solid catalysts (Bootsma et al., 2008), and ABE (acetone, butanol, ethanol) production from DDGS by solventogenic Clostridia (Ezeji and Blaschek, 2008). Economic analysis of a modified dry milling process, where the fiber and residual starch is extracted and fermented to produce more ethanol from the distillers grains while producing highly concentrated protein co-product, has shown that the process is economically viable resulting in an increase in net present value (Perkis et al., 2008). According to the study, the revenue is expected to increase further with improved amino acid profile of the protein rich co-products and lower cost of cellulase enzyme mixture. Also, Kim and Dale (2008) discuss using life cycle analysis to enhance the environmental performance of the corn based ethanol. On the second phase of the research, concerted efforts were directed on assessing compositional variability of dry milling co-products collected from 4 different dry grind ethanol plants has been measured and its effect on enzymatic digestibility and fermentability. Fermentation utilized a recombinant glucose/xylose co-fermenting yeast (Saccharomyces cerevisiae 424A (LNH-ST)). No significant compositional variability among the samples was found. Simultaneous saccharification and glucose/xylose co-fermentation of the pretreated distillers grains at solids and cellulase loadings of 150 g dry solids per liter and 6.4 mg protein per g dry substrate, respectively, yielded 74-801% of theoretical maximum ethanol concentration using recombinant Saccharomyces cerevisiae 424A (LNH-ST). The paper summarizing the results from the second phase of the Midwest Consortium is currently submitted to Bioresource Technology journal. The copy of the paper submitted is enclosed.

09 BIOMASS FUELS↗

Single Atom Catalysts: A Review of Characterization Methods

Abstract Single atom catalysts (SACs) harbor a potential to exceed nanoparticle catalysts in terms of activity, stability and selectivity in a growing number of chemical reactions. Although their investigation is attracting significant attention, important fundamental questions focusing on key physicochemical properties of SACs (e. g., structure – property relationships, structural dynamics, reaction‐driven restructuring) remain unanswered. A main challenge for research in the field is how to reliably characterize the environments of single atoms in the presence of complicating factors such as low weight loadings, strong metal‐support interactions, and atomic and multiscale heterogeneity of bonding in the single atom sites. This review addresses this challenge – identifying catalytically relevant features of physicochemical properties of single atoms (charge state, electronic structure, atomic configuration, bonding interactions with a support) and surveying advanced tools/methods for characterizing them. The review places a strong emphasis on multimodal methods exploiting X‐ray absorption, emission and photoelectron spectroscopies, and provides several examples from the authors’ research that demonstrate their use as powerful tools for SAC characterization.

Kottwitz, Matthew↗

TiO{sub 2} supported on rod-like mesoporous silica SBA-15: Preparation, characterization and photocatalytic behaviour

Highlights: Black-Right-Pointing-Pointer Rod-like SBA-15 and normal SBA-15 were used to prepare TiO{sub 2}/SBA-15 composites. Black-Right-Pointing-Pointer TiO{sub 2}/SBA-15 composites were studied as catalysts for methyl orange photodegradation. Black-Right-Pointing-Pointer TiO{sub 2}/Rod-SBA-15 exhibited higher photocatalytic activity than TiO{sub 2}/Nor-SBA-15. Black-Right-Pointing-Pointer The higher catalytic activity was a result of the controlled morphology of SBA-15. -- Abstract: TiO{sub 2} nanoparticles have been successfully incorporated in the pores of mesoporous silica SBA-15 with different morphologies by a wet impregnation method. The composites were characterized by powder X-ray diffraction (XRD), scanning electron microscopy (SEM), inductively coupled plasma (ICP) emission spectroscopy, transmission electron microscopy (TEM), N{sub 2}-sorption and UV-Vis diffuse reflectance spectroscopy. The photodegradation of methyl orange (MO) was used to study their photocatalytic property. It is indicated that the morphology of SBA-15 had a great influence on the photocatalytic activity of the composites. When TiO{sub 2}/SBA-15 composite was prepared by loading TiO{sub 2} nanoparticles on uniform rod-like SBA-15 of 1 {mu}m length, it showed higher photocatalytic degradation rate than that on less regular but much larger SBA-15 support. This difference was rationalized in terms of the homogeneously distributed and shorter channels of rod-like SBA-15, which favored mass transport and improved the efficient utilization of the pore surface.

36 MATERIALS SCIENCE↗

Multi-pass flow-through reductive catalytic fractionation

Reductive catalytic fractionation (RCF) is a promising lignin-first biorefining strategy that selectively extracts and depolymerizes lignin from whole biomass. Flow-through (FT)-RCF enables physical separation of the biomass and catalyst, but this process configuration typically operates at high solvent-to-biomass ratios. Here, we demonstrate multi-pass FT-RCF, wherein the lignin-enriched solvent obtained after an initial FT-RCF step is recycled and used in subsequent FT-RCF without intermediate lignin recovery. Multi-pass FT-RCF reduces the solvent-to-biomass ratio from 48 to 1.9 L/kg, which is a lower solvent loading than is accessible in batch reactors, without negative impacts on delignification and monomer yield with up to 12 wt % lignin in the solvent. Overall, this work demonstrates that solvent demand in RCF processes, which is a key cost and energy driver to enable this process at scale, can be reduced by recycling lignin oil between RCF reactions.

09 BIOMASS FUELS↗

Tuning the Placement of Pt “Single Atoms” on a Mixed CeO 2 –TiO 2 Support

Defect sites on the oxide supports can be used to anchor and activate "single-atoms" catalysts (SACs). By engineering the anchoring sites for supporting SACs, one can alter their electronic and atomic structures which, in turn, define their activity, selectivity, and stability for catalytic reactions. To create and tune unique sites for Pt SACs on CeO 2 support, in this work, we synthesized a system consisting of CeO 2 decorated on TiO 2 nano-oxides for supporting the Pt SACs and investigated the effect of Pt weight loading. Here, a combination of multiple structural characterization methods including diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS), X-ray photoelectron spectroscopy (XPS) and X-ray absorption spectroscopy (XAS) were employed to characterize the distribution of charge states of single atoms and evaluate the heterogeneity of their binding sites. We have found that the placement of Pt atoms can be tuned on a mixed oxide surface by changing the weight loading of Pt.

77 NANOSCIENCE AND NANOTECHNOLOGY↗