Search NASA⌕ Search

SEARCH · Search NASA

Results for “drying methods”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Effect of Water on Fracture Mechanical Properties of Shales

Abstract Recognition of the potential for subcritical fracture growth of rocks is essential for the evaluation of long‐term stability of fluids trapped in geologic structures. In shales, subcritical fracture growth may control migration of hydrocarbons in source rock and unconventional reservoirs and of sequestered CO 2 across top seals. Using the double torsion method, we investigated the mode‐I fracture mechanical properties of three shales of different composition, namely, Woodford Shale, Mancos Shale, and Marcellus Shale, under water‐saturated conditions, in ambient air, and in dry CO 2 gas conditions to systematically investigate the effect of water on the fracture growth properties of shales. The clay‐rich (illite with minor kaolinite) Woodford and Mancos Shales demonstrate a strong water‐weakening effect despite their low smectite content, with the fracture toughness reduced by up to 54% and the subcritical fracture growth index by up to 77% under water‐saturated conditions compared to tests in ambient air. Carbonate‐rich Marcellus Shale, in contrast, displays negligible water‐weakening effects. The clay‐CO 2 interaction is minor for the three shales. Specimens treated with a hydrophobic surface coating were also tested to limit water‐weakening effects to the fracture tip. Data from these tests reveal rate‐dependent stress intensity factor‐velocity curves for clay‐rich Woodford and Mancos Shales suggesting a competition between mechanical fracture growth and physicochemical water‐rock interactions. Our results suggest that subcritical failure by water‐enhanced subcritical fracture growth could significantly increase brittle failure in clay‐rich shales.

Chen, Xiaofeng↗

Adaptive Grid Redistribution for a 1D Model of Turbulence and Clouds

In global atmospheric models, resolving stratocumulus (Sc) in the vertical is computationally expensive. However, Sc appear only under special meteorological conditions. Therefore, there is motivation to refine the vertical grid levels adaptively. In order to facilitate the possibility of parallelization on graphical processing units, our grid adaptation method prescribes the number of vertical levels a priori. Then grid levels are relocated toward altitude ranges in need of refinement. Because the method relocates existing grid levels, rather than adding extra levels, there is a risk of creating regions with overly coarse grid spacing, that is, voids in the grid mesh. To prevent such voids from forming, a simple method is developed to impose a maximum grid spacing. To decide where to place enhanced resolution, the authors develop an empirical mesh refinement criterion. It refines grid spacing near the ground, near strong temperature gradients, and within clouds. Our grid adaptation method is implemented in a single-column model and evaluated on four test cases: decaying stratocumulus, developing shallow cumulus, a quasi-stationary stratocumulus deck, and the diurnal cycle of a dry boundary layer. In the stratocumulus cases, mesh refinement leads to improvements in both the time evolution of fields and their time averages. The other two cases show smaller differences.

Carstensen, Steffen [Univ. of Wisconsin, Milwaukee↗

The evolution of the M1 local structure during preparation of VMoNbTeO catalysts for ethane oxidative dehydrogenation to ethylene

The so-called M1 phase (the common formula (TeO) x (Mo, V, Nb) 5 O 14 ) is a very promising catalyst for ethane oxidative dehydrogenation (ODE). It shows 90% selectivity to ethylene at 78% ethane conversion (400 °C, contact time – 5.5 s). The active crystal structure is formed under certain synthetic conditions in VMoNbTe mixed oxides. This paper is devoted to the analysis of how the local and average structure of the M1 phase is developed during the synthesis and what happens at particular synthetic steps. The analysis of the local structure was performed using the EXAFS and pair distribution function (PDF) methods. The EXAFS analysis of the initial VMoTe water solution and VMoNbTe slurry showed that Anderson-type heteropoly anions are formed in the solution and are preserved after fast spray-drying of the slurry. Nb cations do not enter the structure of the polyanions, but form an extended hydrated oxide matrix, where distorted NbO 6 and NbO 7 polyhedrons are connected to each other. The hydrated oxide matrix with captured polyanions provides the compositional homogeneity of the precursor. The distances in the second coordination shell are redistributed after thermal treatment at 310 °C. After being heated at T > 350°, the local structure of the M1 phase is organized and pentagonal domains are formed. These domains consist of a NbO 7 pentagonal bipyramid and five MeO 6 adjacent octahedra (Me = Mo, V). In the first stages, the building blocks are stacked along the [001] direction. The crystallization process results in the connection of the pentagonal domains to the extended polygonal grid. The formation of the regular grid with TeO x containing channels is accompanied by the increase in ethane conversion and ethylene selectivity of the catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Impact of UV-induced ozone and low-energy Ar + -ion cleaning on the chemical structure of Cu(In,Ga)(S,Se) 2 absorber surfaces

Dry buffer layer deposition techniques for chalcopyrite (CIGSSe)-based thin-film solar cells lack the surface-cleaning characteristics of the commonly used CdS or Zn(O,S) wet-chemical bath deposition. Here, a UV-induced ozone and/or a low-energy Ar + -ion treatment could provide dry CIGSSe surface cleaning steps. To study the impact of these treatments, the chemical surface structure of a CIGSSe absorber is investigated. For this purpose, a set of surface-sensitive spectroscopic methods, i.e., laboratory-based x-ray photoelectron spectroscopy and x-ray-excited Auger electron spectroscopy, is combined with synchrotron-based soft x-ray emission spectroscopy. After treatment times as short as 15 s, the UV-induced ozone treatment decreases the amount of carbon adsorbates at the CIGSSe surface significantly, while the oxygen content increases. This is accompanied by the oxidation of all absorber surface elements, i.e., indium, selenium, sulfur, and copper. Short (60 s) low-energy Ar + -ion treatments, in contrast, primarily remove oxygen from the surface. Longer treatment times also lead to a removal of carbon, while extremely long treatment times can also lead to additional (likely metallic) Cu phases at the absorber surface as well.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fracture Toughness Evaluation for Sandia Mock-up Stainless Steel Canister Weldment Using Spiral Notch Torsion Fracture Toughness Test

Many radioactive materials within the nuclear fuel cycle present a significant hazard. Such materials include spent nuclear fuel, high-level waste, legacy waste and other nuclear materials that have no current outlet than storage. These materials are often held in long-term storage as an interim stage within their lifecycle. Lifecycles can include reuse or disposal. Safety and security of spent nuclear fuel (SNF) interim storage installations are very important, due to a great concentration of fission products, actinides and activation products. Stress corrosion cracking of interim storage containers has been identified as a high priority data gap by the Department of Energy. However, little has been done with regards to the canister weld material properties, including the fracture toughness, and their impact on stress corrosion, until recently from Sandia National Laboratory canister mockup program. Furthermore, because no post-weld heat treatment was required, the associated high tensile residual stress within these canister welds can drive the initiation and growth of stress corrosion cracking (SCC) cracks. Thus, the fracture mechanical property, such as fracture toughness, is an essential information to understand the canister weldment fracture resistance behavior and to support mitigation protocol development to counter SCC. In this work, we carried out fracture toughness evaluation on the received mock-up canister weldments from Sandia, using spiral notch torsion fracture test technology. The details of the weldment fracture toughness evaluation program development at ORNL are presented in this progress report. The objective of this research is to collect fracture toughness data on the mock-up canister weldment from Sandia National Laboratory. Data will be collected under quasi-static fracture loading using the Oak Ridge National Laboratory (ORNL) developed Spiral Notch Torsion Test (SNTT) technology carried out on a biaxial tension/torsion tester. These data will be used to support the ongoing SNF dry storage canister modeling activities and to address regulatory issues associated with canister container integrity and the follow-on SNF system transport reliability. SNTT has been a recent breakthrough in measuring fracture toughness for different materials, including metals, ceramics, concrete and polymers composites. Due to its high geometry constraint and unique loading condition, SNTT can be used to measure the fracture toughness with smaller specimens without concern of size effects. The application of SNTT to brittle materials has been proved to be successful. The micro-cracks induced by original notches in brittle materials could ensure crack growth in SNTT samples. Therefore, no fatigue pre-cracks are needed. The application of SNTT to the ductile material to generate valid toughness data will require a test sample with sufficient crack length to increase the sample fracture tip localized constraint. Fatigue pre-crack growth techniques are employed to introduce sharp crack front into the sample. Previously, only rough calculations were applied to estimate the compliance evolution in the SNTT crack growth process; while accurate quantitative descriptions have never been attempted. This generates an urgent need to understand the crack evolution during the SNTT fracture testing process of ductile materials. The newly developed governing equations for SNTT crack growth estimate are used to control the fatigue crack growth to effectively reaching the target crack length. The detailed SNTT approach and its estimated fracture toughness for the as-received Sandia canister weldment and the associated baseline 304 stainless steel are presented in this report. In the past SNTT technology has also been successfully applied to investigate the fracture behavior of X52 and X80 steels and the X52 welded materials used for hydrogen infrastructures. The current study in supporting Sandia SNF Dry Storage Mock-up Canister Program is the first attempt of applying SNTT to the highly ductile stainless steel and the associated weld materials. The SNTT test results indicate that SNTT method is a reliable test approach with good repeatability in applying to SS304 steel and SS304/308 weld material. The estimate JQ upon fracture for the baseline SS304 steel is at 1618 lb/in. The estimate JQ upon fracture for the SS304/308 weld from HAZ and weld specimens are 720 lb/in and 850 lb/in, respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Application of PRIM for understanding patterns in carbon dioxide model-observation differences

Reducing uncertainties in regional carbon balances requires a better understanding of CO 2 transport in synoptic weather systems. Here, we apply the Patient Rule Induction Method (PRIM), a data-mining method to identify high-density regions for a target-class within an input parameter space, to airborne observations of potential temperature, wind speed, water vapor mixing ratio, and CO 2 dry mol fraction gathered during the Atmospheric Carbon and Transport (ACT)-America Summer 2016 and Winter 2017 campaigns. ACT observations were targeted at expert-designated cases of fair weather and near-frontal warm and cold sector air at atmospheric boundary-layer, lower-, and higher free tropospheric levels (ABL, LFT, and HFT, respectively). We investigate atmospheric characteristics of these pre-defined cases and associated CO 2 model-observation-differences in the mesoscale WRF-Chem model. PRIM results separate winter- and summertime observations as well as observations from ABL, LFT, and HFT with enrichment factors of 4.0–20.5 inside the PRIM box compared to the entire dataset but cannot distinguish between near-frontal warm and cold sector observations in the higher free troposphere. Analyzing of the parameter space constrained by PRIM, we find that large magnitude model observation differences preferentially associated with times when atmospheric conditions are less typical. This association suggests that PRIM could provide a useful tool for isolating atmospheric conditions with large-magnitude and non-Gaussian CO 2 -residuals for targeted transport model evaluation and to potentially improve inversion results during synoptically active periods.

Gerken, Tobias [James Madison Univ., Harrisonburg,↗

Research on graphite reinforced glass matrix composites

The results of research for the origination of graphite-fiber reinforced glass matrix composites are presented. The method selected to form the composites consisted of pulling the graphite fiber through a slurry containing powdered glass, winding up the graphite fiber and the glass it picks up on a drum, drying, cutting into segments, loading the tape segment into a graphite die, and hot pressing. During the course of the work, composites were made with a variety of graphite fibers in a glass matrix.

Bacon, J. F.↗

Research on Graphite Reinforced Glass Matrix Composites

This report contains the results obtained in the first twelve months of research under NASA Langley Contract NAS1-14346 for the origination of graphite-fiber reinforced glass matrix composites. Included in the report is a summary of the research by other investigators in this area. The method selected to form the composites consisted of pulling the graphite fiber through a slurry containing powdered glass, winding up the graphite fiber and the glass it picks up on a drum, drying, cutting into segments, loading the tape segment into a graphite die, and hot pressing. During the course of the work, composites were made with a variety of graphite fibers in a C.G.W. 7740 (Pyrex) glass matrix. The graphite fibers used included Hercules HMS, Hercules HTS, Thornel 300S, and Celanese DG-102 and, of these, the Hercules HMS and Celanese DG-102 graphite fibers in C.G.W. 7740 gave the most interesting but widely different results. Hercules HMS fiber in C.G.W. 7740 glass (Pyrex) showed an average four-point flexural strength of 848 MPa or 127,300 psi. As the test temperature was raised from room temperature to 560 C in argon or vacuum, the strength was higher by 50 percent. However, in air, similar tests at 560 C gave a severe loss in strength. These composites also have good thermal cycle properties in argon or vacuum, greatly increased toughness compared to glass, and no loss in strength in a 100 cycle fatigue test. Celanese DG-102 fiber in C.G.W. 7740 glass (Pyrex) had a much lower flexural strength but did not suffer any loss in this strength when samples were heated to 560 C in air for 4 hrs.

Bacon, J. F.↗

Biomass of the cryptoendolithic microbiota from the Antarctic desert

Extractable lipid phosphate was used to determine the biomass of the cryptoendolithic microbiota that colonizes sandstone rocks in the Ross Desert region of Antarctica. The mean amount of lipid phosphate was 0.053 micromole/cm2 (n = 9), which equals 2.54 g of C per m2 (range, 1.92 to 3.26 g of C per m2) of biomass in the biotic zone of these rocks. The turnover of phospholipids was comparable to that of temperate sediments and soils (t1/2, 6 to 9 days) at 0 degrees C and a light intensity of 305 micromoles of photons per m2 per s, indicating that this was a good method to measure viable biomass. The biomass was 0.3 to 9.6% of the total carbon content of the biotic zone and was about 2 orders of magnitude smaller than the epilithic lichen dry weight at a location some 7 degrees north in latitude. The cryptoendolithic microbiota had a uniform density throughout the biotic zone under the rock surface. The results indicate that the cryptoendolithic microbial biomass is small but viable in this unique, extreme ecosystem.

NASA Discipline Exobiology↗

Method and apparatus for lysing and processing algae

Methods and apparatus for processing algae are described in which a hydrophilic ionic liquid is used to lyse algae cells at lower temperatures than existing algae processing methods. A salt or salt solution is used as a separation agent and to remove water from the ionic liquid, allowing the ionic liquid to be reused. The used salt may be dried or concentrated and reused. The relatively low lysis temperatures and recycling of the ionic liquid and salt reduce the environmental impact of the algae processing while providing biofuels and other useful products.

42 ENGINEERING↗

Play-fairway analysis for geothermal exploration: Examples from the Great Basin, western USA

Elevated permeability within fault systems provides pathways for circulation of geothermal fluids. Future geothermal development depends on precise and accurate location of such fluid flow pathways in order to both accurately assess geothermal resource potential and increase drilling success rates. The collocation of geologic characteristics that promote permeability in a given geothermal system define the geothermal ‘fairway’, the location(s) where upflow zones are probable and where exploration efforts including drilling should be focused. We define the geothermal fairway as the collocation of 1) fault zones that are ideally oriented for slip or dilation under ambient stress conditions, 2) areas with a high spatial density of fault intersections, and 3) lithologies capable of supporting dense interconnected fracture networks. Areas in which these characteristics are concomitant with both elevated temperature and fluids are probable upflow zones where economic-scale, sustainable temperatures and flow rates are most likely to occur. Employing a variety of surface and subsurface data sets, we test this ‘play-fairway’ exploration methodology on two Great Basin geothermal systems, the actively producing Brady’s geothermal system and a ‘greenfield’ geothermal prospect at Astor Pass, NV. These analyses, based on 3D structural and stratigraphic framework models, reveal subsurface characteristics about each system, well beyond the scope of standard exploration methods. At Brady’s, the geothermal fairways we define correlate well with successful production wells and pinpoint several drilling targets for maintaining or expanding production in the field. In addition, hot-dry wells within the Brady’s geothermal field lie outside our defined geothermal fairways. At Astor Pass, our play-fairway analysis provides for a data-based conceptual model of fluid flow within the geothermal system and indicates several targets for exploration drilling.

15 GEOTHERMAL ENERGY↗

Sol-gel process for the manufacture of high power switches

According to one embodiment, a photoconductive semiconductor switch includes a structure of nanopowder of a high band gap material, where the nanopowder is optically transparent, and where the nanopowder has a physical characteristic of formation from a sol-gel process. According to another embodiment, a method includes mixing a sol-gel precursor compound, a hydroxy benzene and an aldehyde in a solvent thereby creating a mixture, causing the mixture to gel thereby forming a wet gel, drying the wet gel to form a nanopowder, and applying a thermal treatment to form a SiC nanopowder.

36 MATERIALS SCIENCE↗

Production of cerium dioxide microspheres by an internal gelation sol–gel method

An internal gelation sol-gel technique was used to prepare cerium dioxide microspheres with uniform diameters near 100 µm. In this process, chilled aqueous solutions containing cerium, hexamethylenetetramine (HMTA), and urea are transformed into a solid gel by heat addition and are subsequently washed, dried, and sintered to produce pure cerium dioxide. Cerous nitrate and ceric ammonium nitrate solutions were compared for their usefulness in microsphere production. Gelation experiments were performed with both cerous nitrate and ceric ammonium nitrate to determine desirable concentrations of cerium, HMTA, and urea in feed solutions as well as the necessary quantity of ammonium hydroxide added to cerium solutions. Analysis of the pH before and after sample gelation was found to provide a quantitative metric for optimal parameter selection along with subjective evaluations of gel qualities. The time necessary for chilled solutions to gel upon inserting into a hot water bath was determined for samples with a variety of parameters and also used to determine desirable formulations for microsphere production. A technique for choosing the optimal mixture of ceric ammonium nitrate, HMTA, and urea was determined using gelation experiments and used to produce microspheres by dispersion of the feed solution into heated silicone oil. Gelled spheres were washed to remove excess reactants and reaction products before being dried and sintered. X-ray diffraction of air-dried microspheres, sintered microspheres, and commercial CeO 2 powders indicated that air-dried and sintered spheres were pure CeO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Method for Estimating Potential Energy and Cost Savings for Cooling Existing Data Centers

NREL has developed a methodology to prioritize which data center cooling systems could be upgraded for better efficiency based on estimated cost savings and economics. The best efficiency results are in cool or dry climates where 'free' economizer or evaporative cooling can provide most of the data center cooling. Locations with a high cost of energy and facilities with high power usage effectiveness (PUE) are also good candidates for data center cooling system upgrades. In one case study of a major cable provider's data centers, most of the sites studied had opportunities for cost-effective cooling system upgrades with payback period of 5 years or less. If the cable provider invested in all opportunities for upgrades with payback periods of less than 15 years, it could save 27% on annual energy costs.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Flow Processes in the Dry Regime: The Effect on Capillary Barrier Performance

Engineered capillary barriers typically consist of two layers of granular materials designed so that the contrast in material hydraulic properties and sloping interface retains infiltrating water in the upper layer. We report here on the results of two bench-top capillary barrier experiments, interpretation, and numerical modeling. We measured hydraulic parameters for two coarse materials using standard methods and found that the materials had similar hydraulic properties despite being morphologically different (round vs. angular). The round sand provided a better functioning capillary barrier than the angular sand, but neither experiment could be characterized as a perfectly working capillary barrier. In both cases, more than 93% of the infiltrating water was successfully diverted from the lower layer, however, infiltration into the underlying layer was observed in both systems. Based on this work, we believe that non-continuum processes such as vapor diffusion and film flow contribute to the observed phenomena and are important aspects to consider with respect to capillary barrier design, as well as dry vadose zone processes in general. Using a theoretical film flow equation that incorporates the surface geometry of the porous material we found that infiltration into the coarse underlying sand layer appeared to be dominated by water film flow. The NUFT (Non-isothermal Unsaturated-saturated Flow and Transport) model was used for qualitative comparison simulations. We were able to reproduce the barrier breach observed in the experiments using targeted parameter adjustment, by which pseudo-film flow was successfully simulated.

36 MATERIALS SCIENCE↗

Soiling of building envelope surfaces and its effect on solar reflectance – Part II: Development of an accelerated aging method for roofing materials

Highly reflective roofs can decrease the energy required for building air conditioning, help mitigate the urban heat island effect, and slow global warming. However, these benefits are diminished by soiling and weathering processes that reduce the solar reflectance of most roofing materials. Soiling results from the deposition of atmospheric particulate matter and the growth of microorganisms, each of which absorb sunlight. Weathering of materials occurs with exposure to water, sunlight, and high temperatures. This study developed an accelerated aging method that incorporates features of soiling and weathering. The method sprays a calibrated aqueous soiling mixture of dust minerals, black carbon, humic acid, and salts onto preconditioned coupons of roofing materials, then subjects the soiled coupons to cycles of ultraviolet radiation, heat and water in a commercial weatherometer. Three soiling mixtures were optimized to reproduce the site-specific solar spectral reflectance features of roofing products exposed for 3 years in a hot and humid climate (Miami, Florida); a hot and dry climate (Phoenix, Arizona); and a polluted atmosphere in a temperate climate (Cleveland, Ohio). A fourth mixture was designed to reproduce the three-site average values of solar reflectance and thermal emittance attained after 3 years of natural exposure, which the Cool Roof Rating Council (CRRC) uses to rate roofing products sold in the US. This accelerated aging method was applied to 25 products₋single ply membranes, factory and field applied coatings, tiles, modified bitumen cap sheets, and asphalt shingles₋and reproduced in 3 days the CRRC's 3-year aged values of solar reflectance. In conclusion, this accelerated aging method can be used to speed the evaluation and rating of new cool roofing materials.

54 ENVIRONMENTAL SCIENCES↗

Nondestructive Evaluation of Alkali-Silica Reaction in High-Strength Concrete for Aging Structures Sustainability

Concrete is a multiphase geo-material, which is utilized extensively in passive supporting and shielding structures at nuclear facilities. Chemo-mechanical degradation of concrete in old structures is a challenge to sustainability of aging commercial light water reactors. Alkali-silica reaction (ASR) is a common slowly evolving chemo-mechanical damage mechanism of concrete, which could take tens of years to reach the threshold stage when visible cracks appear in a concrete structure. In ASR, concrete constituents react with each other, namely the alkalis in the pore solution of hydrated cement paste (mostly K{sup +}OH{sup -} and Na{sup +}OH{sup -}) react with non-crystalline silica (SiO{sub 2}) of the aggregates to form highly hydrophilic gel. At sufficient levels of ambient relative humidity (typically above 85%), imbibition of water causes expansion of the ASR gel, which results in cracking of constrained reinforced concrete and ultimate structural weakening below safety margin levels. Stability and functional performance of concrete structures potentially suffering from chemo-mechanical deterioration due to ASR is evaluated in a multi-stage process involving material evaluation and structural engineering analysis. Existing methods used by industry for concrete material evaluation are based on extrusion of cores from multiple locations in a structure, and destructive laboratory tests on cores. Because each destructive test requires separate core extrusion, the total number of cores taken from the structure at once could be numbering in hundreds. Laboratory tests include petrography (high resolution optical microscopy of core sections) to develop damage rating index (DRI) score of concrete cores. Another test may involve chemical pore solution extraction from cores, and solution speciation analysis using inductively coupled plasma and mass spectroscopy (ICP/MS). Other tests may consist of mechanical evaluation of cores strength and fracture toughness. The DRI score of concrete material as well as other information obtained from the laboratory tests is subsequently used in structural engineering calculations, where stresses in the entire structure are modeled to evaluate its safety and mechanical stability. Extrusion of a large number of cores is highly undesirable for evaluation of nuclear facility concrete structures. The amount of destructive material testing could be minimized by developing methods for in-situ NDE of ASR to quantify the amount of deterioration that is occurring in the structure, and to identify areas in the structure where more deterioration may be occurring.

36 MATERIALS SCIENCE↗

Wet to Dry Controls Lanthanide Scandate Synthesis

The choice of temperature and gas conditions used in a water pressure-controlled reactor is guided by density functional theory (DFT) to synthesize nearly phase pure lanthanide scandate nanoparticles (LnScO 3 , Ln = La, Nd, Sm, Gd). In this synthetic method, low water vapor partial pressures, well below water’s gas liquidus, inhibit particle growth, while an excess of water vapor results in undesired rare earth hydroxide and oxyhydroxide secondary phases. The optimal humidity for high-purity LnScO 3 particle synthesis is shown to vary with the lanthanide; DFT is used to calculate the thermodynamics of secondary phase formation for each lanthanide tested, such that the role of water vapor may be quantified and used to maintain phase purity (greater than 96 mol%) across the series. Furthermore, the combination of thermodynamic calculation and experimental confirmation with this pressure-controlled reactor provides an opportunity to explore analogous syntheses of other inorganic perovskite nanoparticles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗