Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66

Liquid-metal-induced fracture mode of martensitic T91 steels

The liquid–metal-induced fracture mode of T91 martensitic steel was investigated by using transmission electron microscopy techniques to characterize the microstructure and crack network in specimens obtained from focused-ion beam machining at and immediately below the fracture surface. Contrary to previous claims of quasi-cleavage fracture, the dominant fracture mode is intergranular cracking at martensite laths and prior austenite grain boundaries. These fracture mode results clarify an outstanding issue in liquid–metal embrittlement of steels that generally occur in a heavily-deformed microstructure. Several cracks were arrested at intergranular carbides, suggesting a metallurgical strategy for impeding liquid–metal-induced crack propagation.

36 MATERIALS SCIENCE↗

Evaluation of high strength, high conductivity CuNiBe alloys for fusion energy applications

The unirradiated tensile properties for several different heats and thermomechanical treatment conditions of precipitation strengthened Hycon 3HPTM CuNiBe (Cu-2%Ni-0.35%Be in wt.%) have been measured over the temperature range of 20-500 C for longitudinal and long transverse orientations. The room temperature electrical conductivity has also been measured for several heats, and the precipitate microstructure was characterized using transmission electron microscopy. The CuNiBe alloys exhibit very good combination of strength and conductivity at room temperature, with yield strengths of 630-725 MPa and electrical conductivities of 65-72% International Annealed Copper Standard (IACS). The strength remained relatively high at all test temperatures, with yield strengths of 420-520 MPa at 500 C. However, low levels of ductility (<5% uniform elongation) were observed at test temperatures above 200-250 C, due to flow localization near grain boundaries (exacerbated by having only 10-20 grains across the gage thickness of the miniaturized sheet tensile specimens). Scanning electron microscopy observation of the fracture surfaces found a transition from ductile transgranular to ductile intergranular fracture with increasing test temperature. Fission neutron irradiation to a dose of ~0.7 displacements per atom (dpa) at temperatures between 100 and 240 C produced a slight increase in strength and a significant decrease in ductility. The measured tensile elongation increased with increasing irradiation temperature, with a uniform elongation of ~3.3% observed at 240 C. The electrical conductivity decreased slightly following irradiation, due to the presence of defect clusters and Ni, Zn, Co transmutation products. Considering also previously published fracture toughness data, this indicates that CuNiBe alloys have irradiated tensile and electrical properties comparable or superior to CuCrZr and oxide dispersion strengthened copper at temperatures <250 C, and may be an attractive candidate for certain fusion energy structural applications. Conversely, CuNiBe may not be preferred at intermediate temperatures of 250-500 C due to the poor ductility and fracture toughness of CuNiBe alloys at temperatures >250 C. The potential deformation mechanisms responsible for the transition from transgranular to intergranular fracture are discussed. The possible implications for other precipitation hardened alloys such as nickel based superalloys are briefly discussed.

Zinkle, Steven J↗

On α' precipitate composition in thermally annealed and neutron-irradiated Fe- 9-18Cr alloys [On α' composition in thermally annealed and neutron-irradiated Fe- 9-18Cr alloys]

Ferritic-martensitic steels are a leading candidate for many nuclear energy applications. However, precipitation of nanoscale a’ precipitates during thermal aging at temperatures above 450 °C, or during neutron irradiation at lower temperatures, makes these Fe-Cr steels susceptible to embrittlement. To complement the existing literature, a series of Fe-9 to 18 Cr alloys were neutron-irradiated at temperatures between 320 and 455 °C up to fluences of 20 dpa. In addition, post-irradiation annealing treatments at 500 and 600 °C were performed on the neutron-irradiated Fe-18 Cr alloy to validate the a-a’ phase boundaries. The microstructures were characterized using atom probe tomography and the results were analyzed in light of the existing literature. In conclusion, under neutron irradiation and thermal annealing, the measured a’ concentrations ranged from ~81 to 96 at.% Cr, which were discussed in terms of temperature, precipitate size, technique artefacts, and, possibly, cascade ballistic mixing.

36 MATERIALS SCIENCE↗

Phase decomposition and bubble evolution in Xe implanted U 3 Si 2 at 450°C

We report on the microstructure investigations of a U 3 Si 2 specimen implanted by 84 MeV Xe ions at 450°C. In the region that corresponds to the highest irradiation dose, U 3 Si 2 was found to decompose into a Si-enriched nanocrystalline USi matrix phase and a U-enriched amorphous inclusion phase. Density functional theory (DFT) calculations were used to help understand the decomposition mechanism. Xe bubbles of different morphologies were observed in USi nano-grains, on USi grain boundaries, and phase boundaries. Original U 3 Si 2 micro-grains were preserved on both sides of the irradiation damage peak region within the sample, implying a radiation dose threshold for decomposition of approximately 150 dpa at 450°C. In the preserved U 3 Si 2 region beneath the irradiation damage peak, where critical amount of Xe ions were deposited, a monomodal size distribution of intragranular Xe bubbles with an average size of 2.68 nm formed. In both decomposed and preserved U 3 Si 2 , the size of Xe bubbles was found to be lower than 50 nm. Based on this observation, the fission gas behavior of U 3 Si 2 is controllable and free of run-away swelling despite the occurrence of decomposition at this irradiation temperature. (C) 2019 Elsevier B.V. All rights reserved.

36 MATERIALS SCIENCE↗

Testing fast reactor fuels in a thermal reactor: Comparison of transmutation metallic fuel alloys behavior by scanning electron microscopy

To optimize nuclear waste repository performance, the destruction of minor actinide elements, particularly Np and Am, in a neutron fast spectrum reactor is possible by incorporating these elements into nuclear fuel. Evaluating the performance of minor actinide containing fuel is of paramount importance to enabling this technology. However, such a task is challenging without an available domestic fast spectrum test reactor. A comparison of fuel performance tested in an available domestic thermal reactor at the Idaho National Laboratory, the Advanced Test Reactor, and in a fast spectrum reactor in France (Phénix) is presented here in this study. This study evaluates the capability of using a cadmium shrouded test position to mimic the power profile along the fuel radius present in fast spectrum reactors so that thermally driven phenomenon (e.g., constituent redistribution) can be evaluated in a thermal reactor and determined to be prototypical of a fast reactor. Thus, optical microscopy and scanning electron microscopy has been performed on irradiated 35U-29Pu-4Am-2Np-30Zr fuel samples (where the number preceding the element is the weight percent concentration) from the two mentioned reactors that present similar irradiation temperatures and power conditions. The results indicate that fuel performance phenomena are reproducible in the two irradiation conditions. The redistribution of Zr occurred in the same manner for the two samples. Similar partitioning of U-Pu-Zr phases was observed, and the behavior of Am was similar in the analyzed specimens. Finally, the overall microstructure evolution seems not to be affected by minor actinides addition compared to expected behavior of conventional U-19Pu-10Zr ternary metal fuels for both specimens. Slight differences in fuel cladding chemical interaction were, however, observed. This difference is likely driven by difference in cladding composition rather than irradiation conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electrical stability of a novel sealing glass with (Mn,Co)-spinel coated Crofer22APU in a simulated SOFC dual environment

A novel alkaline-earth silicate (Sr-Ca-Y-B-Si-Zn) sealing glass was developed for solid oxide fuel cell (SOFC) applications. The glass was sandwiched between two metallic interconnect plates and tested for electrical stability in dual environmnet at elevated temperatures of 800-850 degrees C. A ferritic stainless steel (Crofer22APU) was used as the metallic interconnect material in the as-received state and coated with (Mn,Co)3O4 spinel. The isothermal aging results showed stable electrical resistivity at 800-850 degrees C for ~500-1000 hr. The electrical resistivities at 800 or 850 degrees C of the spinel-coated samples were lower than the as-received ones; however, they were still several orders of magnitude higher than typical SOFC functional parts. Interfacial microstructure was characterized and possible reactions are discussed.

Crofer22APU↗

Hardness and modulus of Fe2B, Fe3(C,B), and Fe23(C,B)6 borides and carboborides in the Fe-C-B system

Highlights: • Hardness and modulus of the Fe{sub 2}B, Fe{sub 3}(C,B), Fe{sub 23}(C,B){sub 6} and M{sub 7}C{sub 3} phases are analyzed. • Hardness and modulus of the Fe{sub 3}(C,B) phase are increasing with its B content. • Size effects are apparent for hardness of Fe{sub 2}B, Fe{sub 3}(C,B), Fe{sub 23}(C,B){sub 6} and M{sub 7}C{sub 3}. • The model of Nix and Gao was used to evaluate the load-independent hardness H{sub 0}. • Hardness ranking is Fe{sub 2}B > M{sub 7}C{sub 3} > Fe{sub 3}(C,B) > Fe{sub 23}(C,B){sub 6} - Abstract: This work provides a comparative and comprehensive study of the indentation hardness and indentation modulus of iron-rich borides and carboborides of types Fe{sub 2}B, Fe{sub 3}(C,B), and Fe{sub 23}(C,B){sub 6}. In addition, the hardness and elastic modulus of Cr-rich M{sub 7}C are investigated for comparative purposes. We investigated the impact of increasing B content and indentation size effect (ISE). The phases of interest were stabilized in cast Fe-C-B alloys that varied with respect to the B / (B + C) ratio and heat treatment. The resulting microstructures were characterized by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and wavelength X-ray spectroscopy (WDS). Dynamic in-situ nanoindentation experiments based on the method of continuous stiffness measurement (CSM) were coupled to SEM and EBSD investigations to determine the mechanical properties of the individual borides and carboborides as a function of the indentation depth. The results were compared to values obtained for the Cr-rich M{sub 7}C{sub 3} carbide. It was found that the hardness of the B-rich Fe{sub 3}(C{sub ,}B) phase is considerably higher than pure Fe{sub 3}C and increases with increasing B content. The ISE was present in all investigated phases, and the hardness decreased as a function of indentation depth. The hardness at infinite indentation depth H{sub 0} was estimated according to the model of Nix and Gao. The Fe{sub 2}B phase was found to be the hardest phase (H{sub 0} = 19.04 GPa), followed by M{sub 7}C{sub 3} (H{sub 0} = 16.43 GPa), Fe{sub 3}(C,B) (H{sub 0} = 11.18 to 12.24 GPa), and Fe{sub 23}(C,B){sub 6} (H{sub 0} = 10.39 GPa).

36 MATERIALS SCIENCE↗

Multi-scale and multi-technic microstructure analysis of a linear friction weld of the metastable-β titanium alloy Ti-5Al-2Sn-2Zr-4Mo-4Cr (Ti17) towards a new Post-Weld Heat Treatment

Highlights: • Soft joint showing sharp macro-zones and marked by asymmetrical process effects • Gradient of thermomechanical loads identified through progressive stages of transformation • Highly textured recrystallized β grains at the joint core with distorted β lattice • Lattices, phase fractions, microstructures and hardness homogenized after heat treatment - Abstract: Linear Friction Welding (LFW) is a solid-state joining process producing narrow joints mainly developed for the aircraft industry. The Thermo-Mechanical Processing (TMP) loads imposed on the material cause complex microstructure transformations. This study aimed at characterizing the local microstructures and crystallographic configurations to identify the mechanisms impacting the stability and the mechanical properties of a Ti17 LFW joint with the objective of establishing an innovative homogenizing Post-Weld Heat Treatment (PWHT). The process caused a narrow zone of ±2 mm from the friction interface to reach the isothermal α → β transformation temperature under a heating rate of 500 K/s followed by quenching (−100 K/s). The TMP resulted in the formation a ±3 mm wide soft Process Affected Zone (PAZ) delimited by three characteristic zones: the Welding Line (WL width ≈ 400 μm), The Thermo-Mechanically Affected Zone (TMAZ width ≈ 1 mm) and the Heat Affected Zone (HAZ). β TMP resulted in the total dissolution of the α phase in the joint core (WL + TMAZ) and formed strongly textured {110}<111> β recrystallized grains in the WL by continuous dynamic recrystallization of squeezed prior-β grains in the TMAZ. α + β TMP led to a gradual loss of hardness in the HAZ whose microstructure is similar to the one of the base material (BM) but is subject to gradual α laths dissolution due to the local temperatures experienced during LFW. A PWHT consisting in a β annealing followed by an α + β ageing resulted in a uniformly hardened weld with a homogenized Widmanstätten microstructure in the whole assembly.

36 MATERIALS SCIENCE↗

Validation of an alloy design strategy for stable Fe–Cr–Al–Nb-X ferritic alloys using electron microscopy and atom probe tomography

The Fe–Cr–Al–Nb ferritic alloys strengthened by A₂B Laves phases, with superior oxidation and corrosion resistance, are being considered for high temperature operation within fossil-fired steam power plants to increase process efficiency and reduce CO₂ emissions. In this paper, new sets of alloys based on Fe–30Cr–3Al–1Nb (in weight percent) were designed with (i) a high microstructural stability of Laves phase precipitates in a BCC-Fe matrix and (ii) reduced precipitate free zones along the grain boundaries, targeting an operating temperature of 700 °C. Two alloys with titanium or tungsten additions were down-selected through thermodynamic calculations with a design strategy to maximize the amount of Laves phase at 700 °C and lower the BCC solvus temperature. To validate this design strategy, the candidate alloys were cast, heat treated and aged at 700 °C, and the resulting microstructure was characterized using scanning electron microscopy and atom probe tomography. The alloys with titanium addition (1 wt%) showed monotonic precipitate coarsening. On the other hand, the alloys with tungsten addition (6 wt%) showed a reduced coarsening rate of Laves phase precipitates in the matrix up to 1008 h aging, whereas an acceleration of the precipitate coarsening after that. Atom probe tomography of this alloy revealed the formation of a core-shell precipitate structure with a Nb/Si rich core and W-rich shell, while the alloy with Ti-addition did not show the core-shell structure. The detailed characterization results revealed that the core-shell structure was strongly correlated with the observed two-step coarsening mode in the tungsten containing alloy.

36 MATERIALS SCIENCE↗

Examining the creep strengthening nanoprecipitation in novel highly reinforced heat resistant steels

Here we studied the creep strengthening nanoprecipitation in novel heat resistant steels strengthened by a high density of stable nanoprecipitates. The results show that the high number density of MX nanoprecipitates within the martensitic laths in these steels comes from the great amount of MX former elements present in their chemical compositions and the high dislocation density generated by the martensitic transformation that takes place during cooling after austenitization. These dislocations act as nucleation sites for these nanoprecipitates during the tempering applied after the austenitization and quenching. Atom probe tomography measurements show that these nanoprecipitates are rich in Nb, V, Cr and N for the HDSN1 and HDSN2 steels and V, Cr and N for the HDSN3 steel. The distribution of the nanoprecipitates within the martensitic laths suggests that the creep strengthening produced by the Nb, V, Cr and N nanoprecipitates in the HDSN1 and HDSN2 steels is more effective at pinning dislocations at high temperature than that obtained in the HDSN3 steel by the V, Cr and N nanoprecipitates. However, the high amount of W in the HDSN3 steel enhances the solid solution strengthening at high temperatures, resulting in a similar high temperature strength for all HDSN steels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spatially resolved phase transformation mapping in 410 stainless steel during additive manufacturing visualized via real-time infrared data

Here, in this study, we demonstrate that spatially resolved cooling curves derived from real-time infrared (IR) thermography during additive manufacturing (AM) can capture spatial variations in phase transformation temperatures through cooling curve analysis (CCA). Using this approach, we show that during laser hot-wire deposition of 410 stainless steel (410SS), the martensite start temperature (M s ) evolves dynamically throughout the build. The M s temperature is spatially nonuniform, ranging from 185 °C to 348 °C, with the lowest values toward the build center and higher values toward the upper region of the deposit. In the lower portion of the build, no M s inflection is detected via CCA, consistent with transformation occurring earlier during thermal cycling followed by tempering during subsequent thermal cycles. These trends in M s are corroborated by characterizing the microstructure by electron backscatter diffraction (EBSD). Traditionally, M s is assumed to be constant, and a single interpass temperature is applied during both deposition and residual stress modeling. Our results demonstrate that IR-derived cooling curves provide a route to spatially and temporally resolved transformation temperature tracking for dynamic interpass control and improved residual-stress modeling.

Additive manufacturing↗

Evaluation of high-temperature properties of binary, eutectic Ni-X alloys (X = B, Ca, Ce, La, Y, Zr)

We investigated the high-temperature behavior of binary eutectic nickel-base alloys with low-solubility elements, towards developing alloys with new combinations of structural and functional (e.g. thermal or corrosion) properties. Based on thermodynamic screening, we cast binary near-eutectic Ni-B, Ni-Ca, Ni-Ce, Ni-La, Ni-Y, and Ni-Zr alloys and characterized their microstructure and high-temperature properties. All alloys (except Ni-Ca) contain a fine eutectic microstructure, containing submicron alternating lamellae of γ-Ni and continuous intermetallic phases. The eutectic microstructure did not significantly coarsen at 700°C (except for Ni-B), but measurably coarsened in all alloys at 900°C, most quickly in Ni-B, followed by Ni-Ce, Ni-La, Ni-Y, and Ni-Zr. Coarsening in these alloys occurs by fault migration; diffusion within the intermetallic, and its interfacial energy, likely influence coarsening kinetics. At room-temperature, all alloys possess negligible ductility due to the continuous, brittle intermetallic. At 700 and 900°C, the Ni-Zr alloy showed the best combination of strength and ductility. Oxidation experiments at 900°C on Ni-Zr and Ni-Ce revealed heavy internal oxidation of the continuous intermetallic phase. Overall, the Ni-Zr alloy showed good high-temperature coarsening resistance and strength, though ductility and oxidation resistance require improvement for use in structural applications. Possible routes for improving alloy properties via additive manufacturing are discussed.

Ekaputra, Clement [ORNL] (ORCID:0000000307166479)↗

Direct diffusion bonding of Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2}

Two typical layered ternary compounds, Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2}, were joined directly by solid-state diffusion bonding method. By various bonding tests at 1100-1300 deg. C for 30-120 min under 10-30 MPa, and characterizing the microstructure and diffusion reactive phases of the joints by scanning electron microscopy (SEM), energy dispersive X-ray spectrometer (EDS), transmission electron microscopy (TEM) and X-ray diffraction (XRD), the optimal condition for direct joining of Ti{sub 3}SiC{sub 2} and Ti{sub 3}AlC{sub 2} was obtained. Strong joints of Ti{sub 3}SiC{sub 2}/Ti{sub 3}AlC{sub 2} can be achieved via diffusion bonding, which is attributed to remarkable interdiffusion of Si and Al at the joint interface. The shear strength of the Ti{sub 3}SiC{sub 2}/Ti{sub 3}AlC{sub 2} joints was determined.

36 MATERIALS SCIENCE↗

Preparation and characterization of one-dimensional GaN nanorods with Tb intermediate layer

Graphical abstract: Display Omitted Highlights: ► GaN nanorods have been prepared on Si substrates by magnetron sputtering. ► GaN nanorods are single crystal with hexagonal wurtzite structure. ► GaN nanorods are high-quality crystalline after ammoniating at 950 °C for 15 min. ► Ammoniating temperatures and times affect the growth of GaN nanorods significantly. -- Abstract: GaN nanorods have been successfully prepared on Si(1 1 1) substrates by magnetron sputtering through ammoniating Ga{sub 2}O{sub 3}/Tb thin films. X-ray diffraction (XRD), X-ray photoelectron spectroscope (XPS), FT-IR spectrophotometer, scanning electron microscope (SEM), high-resolution transmission electron microscope (HRTEM), and photoluminescence (PL) spectroscopy were used to characterize the microstructures, morphologies compositions and optical properties of the GaN samples. The results demonstrate that the nanorods are single crystal GaN with hexagonal wurtzite structure and high-quality crystalline after ammoniating at 950 °C for 15 min, which have the size of 100–150 nm in diameter. Ammoniating temperatures and times affect the growth of GaN nanorods significantly. The growth procedure mainly follows the Tb catalyst-assisted VLS mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A carbon foam with a bimodal micro–mesoporous structure prepared from larch sawdust for the gas-phase toluene adsorption

Highlights: ► Network carbon foam containing a bimodal pore distribution was prepared from Larch. ► Liquefaction route was used for the preparation of morphology controllable carbon. ► Pore structure of carbon foam was controlled through KOH activation. - Abstract: A carbon foam with a bimodal micro–mesopore distribution, was prepared by submitting larch sawdust to liquefaction, resinification, foaming, carbonization and KOH activation. The morphology, pore texture and crystal microstructure was characterized by scanning and transmission electron microscopy, nitrogen adsorption analysis and X-ray powder diffraction. A honeycomb structure with adjacent cells was observed for the precursor of carbon foam. After KOH activation, the cell wall of precursor shrunk and broke. This lead to the formation of a well-connected 3D network and developed ligament pore structure (surface area of 554–1918 m{sup 2}/g) containing bimodal pores, 2.1 and 3.9 nm in diameter. The porous carbon foam prepared at 700 °C exhibited a much higher gas-phase toluene removal than commercial activated carbon fiber owing to the 3D network and bimodal pore structure.

36 MATERIALS SCIENCE↗