Search NASA⌕ Search

SEARCH · Search NASA

Results for “nuclear cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,189 records · Page 66
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Experimental research of graphite behavior under the air ingress accident condition of High Temperature Gas-cooled Reactor - 18752

As the major component of both cladding and grid spacer materials of High Temperature Gas-cooled Reactor (HTGR), graphite plays an important role on heat removal during the severe accident sequence. However, its heat transfer behavior in high temperature condition may be affected by the oxidation of graphite when the air or steam ingresses in an accident. In this research, an experiment was conducted to analyze the graphite heat transfer behavior in high temperature oxidable environment. An assembly including two graphite rings was used as the test section. It was heated up by a tungsten wire, which is installed inside the inner graphite ring and be joule heated. Temperature was measured by several K-type thermos-couples in certain positions. Argon gas was injected in advance to avoid the unwanted oxidation by the oxygen in the air. Air was injected into the gap between two graphite rings once the temperature of the inner ring reached target point to create the oxidable environment. Based on the results, a rapid increase of inner graphite ring's temperature can be observed after starting injected the air, and a rapid decrease after stopped the injection. It might due to the chemical reaction heat during the graphite surface oxidation. By comparing the steady state before and after air injection, the inner specimen s temperature is a little bit lower after the oxidation, which suggests that its ability of radiation heat transfer might be enhanced a little bit by oxidation. By visualized the test section, coarser surface at the inner graphite ring can be observed after the oxidation. In addition, about 8.9% mass loss of the oxidized graphite can also be found from the posttest examination. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2020

Progress in demonstrating the performance of Engineered Barriers for the disposal of HLW and SNF: lab studies and demonstration experiments - 20293

Disposal of high-level radioactive waste (HLW) and spent nuclear fuels (SNF) in a geological disposal facility requires a fundamental understanding of the degradation processes of materials used in its engineered barrier system (EBS) over very long timescales. Beyond the wasteform itself (i.e. the borosilicate glass for HLW or the fuel matrix and cladding for SNF), materials often employed in a disposal concept include metallic containers (typically copper and/or carbon steel) and clay-based buffer materials (typically bentonite). In this paper we explore key developments on the long-term evolution of materials employed for the immobilisation, isolation and containment of HLW and SNF in a geological disposal facility, including nuclear glasses, candidate container materials and clay buffers. Our discussion is based on the latest findings from both experimental studies and in-situ demonstration experiments. We present relevant findings from the long-term evolution of HLW glasses (UK composition), metallic materials for the containment system (envisaged in Switzerland, Sweden, Canada and other countries), and bentonite clays (envisaged in many national disposal programmes). (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2014

Reversal bending fatigue test system for investigating vibration integrity of spent nuclear fuel during transportation

Transportation packages for spent nuclear fuel (SNF) must meet safety requirements under normal and accident conditions as specified by federal regulations. During transportation, SNF experiences unique conditions and challenges to cladding integrity due to the vibrational and impact loading during road or rail shipment. Oak Ridge National Laboratory (ORNL) has been developing testing capabilities that can be used to improve the understanding of the impacts on SNF integrity due to vibration loading, especially for high burn-up SNF in normal transportation operation conditions. This information can be used to meet the nuclear industry and U.S.Nuclear Regulatory Commission needs in the area of safety and security of SNF storage and transportation operations. The ORNL developed test system can perform reversal bending fatigue testing to evaluate both the static and dynamic mechanical response of SNF rods under simulated loads. The testing apparatus is also designed to meet the challenges of hot cell operation, including remote installation and detachment of the SNF test specimen, in situ test specimen deformation measurement, and implementation of a driving system suitable for use in a hot cell. The system contains a U frame set-up equipped with uniquely designed grip rigs to protect the SNF rod sample and to ensure valid test results, and uses three specially designed linear variable differential transformers to obtain the in situ curvature measurement. A variety of surrogate test rods have been used to develop and calibrate the test system as well as in performing a series of systematic cyclic fatigue tests. The surrogate rods include stainless steel (SS) cladding, SS cladding with cast epoxy and SS cladding with alumina pellet inserts simulating fuel pellets. Testing to date has shown that the interface bonding between the SS cladding and the alumina pellets has a significant impact on the bending response of the test rods as well as their fatigue strength. The failure behaviours observed from tested surrogate rods provide a fundamental understanding of the underlying failure mechanisms of the SNF surrogate rod under vibration,which has not been achieved previously. The newly developed device is scheduled to be installed in the hot cell in summer 2013 to test high burn-up SNF.

high burn up fuel↗
DOE OSTI2015

The German product quality control of the compacted metallic nuclear waste - 15311

The treatment and safe disposal of spent nuclear fuel is a key challenge of nuclear energy utilization and has to be accomplished regardless the future nuclear of electricity production or phase-out policies. Until June 2005 approx. 6662 tons of spent fuel from German nuclear power plants was sent to the La Hague (France) and Sellafield (UK) plants for reprocessing. An equivalent amount of nuclear waste compounds has contractually to be returned to Germany, which is currently in progress. The returnable waste streams comprise mainly highly-active vitrified waste containing a major part of fission products and actinides, and intermediate-active super-compacted metallic waste containing reprocessed fuel element's structural materials and some technological waste from the reprocessing process itself. Shearing and dissolution of spent fuel leaves scraps of fuel metal cladding, the end-pieces and spacers which are contaminated, activated and irradiating from their life in a reactor core. In fact, this metallic intermediate level radioactive waste makes up a bit more than half of the total volume of the reprocessed waste. At La Hague the metallic waste is super-compacted. Several, typically eight, compacted discs are stacked in a stainless steel container, named CSD-C as for 'Colis Standard de Dechets Compactes'. 4104 containers of such CSD-Cs in 152 transport/storages casks have to be returned to Germany. Each one of them has to be checked and quality certified for its conformity with German national product specifications and acceptance criteria by independent national product quality control inspectors (PKS). The residue package documentation has to be complete and the characterization methods have to be comprehensive. Due to the heterogeneity of metallic waste the characterization and control of its properties is very complex. The nuclear characterization is performed by means of non-destructive measurements, where only a few key nuclides are measured directly. In fact, the proper calculation of the whole nuclear inventory relies on numerous supplementary simulations. The measurement and calculation methodology is scrutinized by PKS in detail and key points are benchmarked with our own simulations for the sake of an independent nuclear inventory declaration check. With respect to the vast amount of documentation and parameters, which have to be checked and verified, PKS had to optimize their checking procedures. For this purpose dedicated proof tools have been developed that shall be applied for selected indicative cross-checks of the relevant parameters. This contribution is dedicated to the procedure of quality control by PKS and examples of actually performed computational verifications of declared nuclear inventory. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2018

Nondestructive Pressure Measurement Technique for Irradiated Nuclear Fuel Rods

Commercial nuclear fuel rods are pre-pressurized with helium before irradiation. During irradiation, the rod internal pressure (RIP) increases due to cladding dimensional changes and pellet fission gas release. RIP is a limiting parameter for rod operation and is a barrier to achieving higher fuel burnup. Currently, the only method for RIP measurement is rod puncture which is a destructive method. Because of the challenges and cost associated with handling irradiated fuel, the existing database on RIP is extremely limited. This paper presents progress towards developing a novel acoustic-based nondestructive examination method to accurately measure the internal gas pressure and gas composition in pressurized containers without the need for puncturing the pressure boundary, with an emphasis on applications to spent nuclear fuel (SNF) rods and radioactive material dry storage canisters.

Montgomery, Rose↗
DOE OSTI2013

Laser shockwave technique for characterization of nuclear fuel plate interfaces

The US National Nuclear Security Agency is tasked with minimizing the worldwide use of high-enriched uranium. One aspect of that effort is the conversion of research reactors to monolithic fuel plates of low-enriched uranium. The manufacturing process includes hot isostatic press bonding of an aluminum cladding to the fuel foil. The Laser Shockwave Technique (LST) is here evaluated for characterizing the interface strength of fuel plates using depleted Uranium/Mo foils. LST is a non-contact method that uses lasers for the generation and detection of large amplitude acoustic waves and is therefore well adapted to the quality assurance of this process. Preliminary results show a clear signature of well-bonded and debonded interfaces and the method is able to classify/rank the bond strength of fuel plates prepared under different HIP conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2015

Accident analysis of heavy water cooled thorium breeder reactor

Thorium has lately attracted considerable attention because it is accumulating as a by-product of large scale rare earth mining. The objective of research is to analyze transient behavior of a heavy water cooled thorium breeder that is designed by Tokai University and Tokyo Institute of Technology. That is oxide fueled, PWR type reactor with heavy water as primary coolant. An example of the optimized core has relatively small moderator to fuel volume ratio (MFR) of 0.6 and the characteristics of the core are burn-up of 67 GWd/t, breeding ratio of 1.08, burn-up reactivity loss during cycles of < 0.2% dk/k, and negative coolant reactivity coefficient. One of the nuclear reactor accidents types examined here is Unprotected Transient over Power (UTOP) due to withdrawing of the control rod that result in the positive reactivity insertion so that the reactor power will increase rapidly. Another accident type is Unprotected Loss of Flow (ULOF) that caused by failure of coolant pumps. To analyze the reactor accidents, neutron distribution calculation in the nuclear reactor is the most important factor. The best expression for the neutron distribution is the Boltzmann transport equation. However, solving this equation is very difficult so that the space-time diffusion equation is commonly used. Usually, space-time diffusion equation is solved by employing a point kinetics approach. However, this approach is less accurate for a spatially heterogeneous nuclear reactor and the nuclear reactor with quite large reactivity input. Direct method is therefore used to solve space-time diffusion equation which consider spatial factor in detail during nuclear reactor accident simulation. Set of equations that obtained from full implicit finite-difference method is solved by using iterative methods. The indication of UTOP accident is decreasing macroscopic absorption cross-section that results large external reactivity, and ULOF accident is indicated by decreasing coolant flow. The power reactor has a peak value before reactor has new balance condition. The analysis showed that temperatures of fuel and claddings during accident are still below limitations which are in secure condition.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2017

PIE of nuclear grade SiC/SiC flexural coupons irradiated to 10 dpa at LWR temperature

Silicon carbide fiber-reinforced SiC matrix (SiC/SiC) composites are being actively investigated for accident-tolerant core structures of light water reactors (LWRs). Owing to the limited number of irradiation studies previously conducted at LWR-coolant temperature, this study examined SiC/SiC composites following neutron irradiation at 230–340°C to 2.0 and 11.8 dpa in the High Flux Isotope Reactor. The investigated materials are chemical vapor infiltrated (CVI) SiC/SiC composites with three different reinforcement fibers. The fiber materials were monolayer pyrolytic carbon (PyC)-coated Hi-NicalonTM Type-S (HNS), TyrannoTM SA3 (SA3), and SCS-Ultra TM (SCS) SiC fibers. The irradiation resistance of these composites was investigated based on flexural behavior, dynamic Young’s modulus, swelling, and microstructures. There was no notable mechanical properties degradation of the irradiated HNS and SA3 SiC/SiC composites except for reduction of the Young’s moduli by up to 18%. The microstructural stability of these composites supported the absence of degradation. In addition, no progressive swelling from 2.0 to 11.8 dpa was confirmed for these composites. On the other hand, the SCS composite showed significant mechanical degradation associated with cracking within the fiber. This study determined that SiC/SiC composites with HNS or SA3 SiC/SiC fibers, a PyC interphase, and a CVI SiC matrix retain their properties beyond the lifetime dose for LWR fuel cladding at the relevant temperature.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2018

Fuel – clad chemical interaction evaluation of the TREAT reactor conceptual low-enriched-uranium fuel element

The Transient Reactor Test (TREAT) facility resides at the Materials and Fuels Complex (MFC) at Idaho National Laboratory (INL). The TREAT reactor is currently undergoing design and engineering studies for its conversion from a high enriched uranium (HEU) to a low-enriched uranium (LEU) core. The conceptual design of the LEU fuel element identified two main design differences compared with the HEU fuel element; namely, it will contain four times more fissionable material in its graphite matrix and distinct nuclear-grade Zirconium alloy, as Zircaloy-3 was used in the HEU fuel assembly and is not commercially available currently. These design changes may impact the magnitude of chemical interaction between fuel and cladding materials during physical contact under expected TREAT operation conditions and, therefore, was evaluated through a combination of experimental testing and thermodynamic modeling in order to determine implications for the fuel assembly. In this study, two potential cladding material types, Zircaloy-4 or Zr-1Nb alloys, were evaluated, and it was found for both material types that the extent of interaction and specific chemical reactions are minimal and no detrimental effect on the overall cladding properties is observed. Here, the resulting interaction layer of 3-6 µm was measured after a 2-week exposure at 820°C. The thermodynamic analysis was extended to temperatures beyond the TREAT reactor operation and accident conditions in order to give some insight that may be of interest for other reactor systems as the High Temperature Gas Reactors (operation above 1,000°C) and for Nuclear Reactor Severe Accident phenomenology study where the UO 2 fuel could reach temperatures over 2,800°C and melt.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2019

Evaluation of Tellurium as a Fuel Additive in Neodymium-Containing U-Zr Metallic Fuel

Phase-stability in a U-Zr-Te-Nd multi-component metallic fuel for advanced nuclear reactors is systematically investigated by taking into account binary, ternary and quaternary interactions between elements involved. Historically, the onset of fuel-cladding chemical interactions (FCCI) greatly limits the burnup potential of U-Zr fuels primarily due to interactions between lanthanide fission products and cladding constituents. Tellurium (Te) is evaluated as a potential additive for U-Zr fuels to bind with lanthanide fission products, e.g. neodymium (Nd), negating or mitigating the FCCI effect. Potential fresh fuel alloy compositions with the Te additive, U-Zr-Te, are characterized. Te is found to completely bind with Zr within the U-Zr matrix. Alloys simulating the formation of the lanthanide element Nd within U-Zr-Te are also evaluated, where the Te-Nd binary interaction dominates and NdTe is found to form as a high temperature stable compound. The experimental observations agree well with the trends obtained from density functional theory calculations. According to the calculated enthalpy of mixing, Zr-Te compound formation is favored in the U-Zr-Te alloy whereas NdTe compound formation is favored in the U-Zr-Te-Nd alloy. Further, the calculated charge density distribution and density of states provide sound understanding of the mutual chemical interactions between elements and phase-stability within the multi-component fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Analysis of Using a Hybrid ZIRCEX Process to Generate High-Assay Low-Enriched Uranium (HALEU) - 20158

Idaho National Lab (INL) is investigating the feasibility of providing High-Assay Low Enriched Uranium (HALEU) by recovering Highly Enriched Uranium (HEU) from spent nuclear fuel (SNF) and downblending the HEU with natural, low-enriched, or depleted uranium (NU, LEU, or DU). That investigation identified that significant quantities of HALEU could be produced with a Hybrid ZIRCEX process to further advanced reactor research while reducing INL's environmental liability. Many new advanced reactor designs are being developed with improved safety, efficiency, and economics. Most require nuclear fuel with U-235 enrichment between 5% and 20%, which is defined as HALEU. Although technically feasible, there is no current domestic capability to make HALEU in the US. While it is anticipated that industry will provide HALEU through commercial enrichment once advanced reactors mature, until a market is established, an interim source of HALEU is needed to enable research and demonstration. An interim source of HALEU could be provided by recovering the HEU in some DOE-managed SNF and downblending it to between 5% and 20% using the Hybrid ZIRCEX Process. ZIRCEX is a dry head-end process to remove cladding (zirconium or aluminum) from SNF. Drying of the SNF is needed prior to introduction to ZIRCEX. After cladding removal, uranium and fission products in the bed material are oxidized and elutriated. In a Hybrid ZIRCEX process, the HEU process stream is sent to a very compact, modular solvent extraction process for uranium purification. The uranyl nitrate from solvent extraction is denitrated and calcined to produce a HALEU product ready for fuel fabrication. The long-lived fission products from solvent extraction are immobilized in glass using a small in-can melt. By removing the cladding before dissolution, the volume of glass waste is reduced by a factor of up to 300 times (when compared to not removing the cladding from the fuel). Other radioactive wastes from the process could be disposed of as Class A or Class B low-level waste. In addition to producing HALEU for advanced reactors, consumption of SNF would reduce DoE's environmental liability. Incorporating low-enriched spent fuel (versus exclusive use of LEU, DU, or NU) into the downblending scheme could reduce the SNF inventory even further. Several downblending and enrichment scenarios using INL fuels were investigated in this study. The results of this analysis show that the Hybrid ZIRCEX process could make a significant contribution to needed HALEU feedstock and reduce the environmental liability of managing SNF at INL. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Development and demonstration of a methodology to evaluate high burnup fuel susceptibility to pulverization under a loss of coolant transient

For economic reasons, the US nuclear industry is renewing efforts to build a technical basis to extend rod average burnup limits above the current regulatory burnup limit of 62 GWd/MTU. The primary driver is to increase pressurized water reactor cycle lengths to 24 months, reducing the number of fresh fuel assemblies and core design constraints, thereby making core energy utilization more efficient. However, fuel pellet fragmentation and pulverization, termed high burnup fuel fragmentation (HBFF), has been observed in the high burnup (>90 GWd/MTU) Halden loss-of-coolant-accident (LOCA) integral test series. The issue gained attention when fuel fragmentation and pulverization were also observed closer to the current US regulatory limit during the US Nuclear Regulatory Commission (NRC) sponsored out-of-core integral test at Studsvik Nuclear in early 2011. This led to NRC concerns with potential changes to fuel and core designs relative to fuel pellet pulverization. In a letter to the NRC Commissioners, the staff specifically identified a need to “…define the boundary of safe operation for key fuel design and operating parameters,” stating that “the staff is challenged to evaluate the acceptability of future fuel design advancements and fuel utilization changes.” As such, it can be concluded that HBFF and potential dispersal into the reactor coolant system introduces additional complications in light-water reactor (LWR) fuel safety evaluations. However, it is not clear how much fuel will be susceptible to HBFF; nor has there been a methodology developed to evaluate fuel susceptibility to HBFF. To that end, this paper proposes an analysis methodology to assess fuel susceptibility to HBFF during LOCA scenarios. The work presented here uses the BISON fuel performance code to evaluate a representative pressurized water reactor fuel rod exposed to a rod average burnup of 75 GWd/MTU. Sensitivity studies investigated the impact of the peak cladding temperature, transient fission gas released, and pre-transient fission gas release on cladding ballooning and burst timing. Subsequently, a methodology to assess fuel susceptibility to HBFF will be developed based on experimental data published in the open literature. The methodology will then be demonstrated by calculating the mass of fuel susceptibility to HBFF. The BISON results conclude that increasing peak cladding temperature drastically decreased time to failure, and decreased balloon size both of which have been confirmed experimentally. Additionally, the effect of pre-transient and transient fission gas release affected cladding balloon size and burst timing. Finally, fuel susceptibility to HBFF significantly decreased as a function of peak cladding temperature.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Assessment of the analysis capability for core-wide PWR pellet-clad interaction screening of Watts Bar Unit 1

This report illustrates the application of the Virtual Environment for Reactor Applications simulation environment to pressurized water reactor core-wide pellet-clad interaction screening, with emphasis on the multi-dimensional analysis capabilities of the BISON fuel performance code. The Virtual Environment for Reactor Applications codes utilized in this effort include the BISON fuel performance code and the VERA-CS sub-element, which combines the MPACT neutron transport code and the COBRA-TF thermal-hydraulics code. The target reactor for this work is Watts Bar Unit 1, cycle 6 and cycle 7, selected on the basis that pellet-clad interaction failures had occurred during power start up in both cycles, despite the moderate power levels. These instances of failure at Watts Bar Unit 1 offered an interesting test of the code’s veracity and a particularly challenging condition for this assessment.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Oxidation Resistance in 1200°C Steam of a FeCrAl Alloy Fabricated by Three Metallurgical Processes

Abstract FeCrAl alloys are a leading candidate material for accident tolerant fuel cladding due to their good performance in both normal light-water reactor operating conditions as well as their resilience to high-temperature accident scenarios. For commercial-scale production, new fabrication techniques need to be investigated. In this study, the effects of fabrication methods on the high-temperature steam oxidation performance of C26M (Fe12Cr6Al2Mo in wt.%) were investigated. Three variants of C26M were manufactured: wrought (cast and forged) (WC26M), powder metallurgy hot isostatic pressing (PMC26M), and laser powder bed fusion additive manufacturing (AMC26M). All three variants were exposed to steam at 1200°C for 2 h. Results showed no significant variation in mass change between the variants after steam exposure. All three variants effectively formed stable protective alumina films with ~0.6–1.3 µ m thickness. This study suggests FeCrAl alloys have excellent resilience to high-temperature steam in nuclear reactor accident scenarios regardless of the fabrication method.

Materials Science↗
DOE OSTI2015

High Burn-Up Spent Nuclear Fuel Vibration Integrity Study

The Oak Ridge National Laboratory (ORNL) has developed the cyclic integrated reversible-bending fatigue tester (CIRFT) approach to successfully demonstrate the controllable fatigue fracture on high burnup (HBU) spent nuclear fuel (SNF) in a normal vibration mode. CIRFT enables examination of the underlying mechanisms of SNF system dynamic performance. Due to the inhomogeneous composite structure of the SNF system, the detailed mechanisms of the pellet-pellet and pellet-clad interactions and the stress concentration effects at the pellet-pellet interface cannot be readily obtained from a CIRFT system measurement. Therefore, finite element analyses (FEAs) are used to translate the global moment-curvature measurement into local stress-strain profiles for further investigation. The major findings of CIRFT on the HBU SNF are as follows: SNF system interface bonding plays an important role in SNF vibration performance. Fuel structure contributes to SNF system stiffness. There are significant variations in stress and curvature of SNF systems during vibration cycles resulting from segment pellets and clad interactions. SNF failure initiates at the pellet-pellet interface region and appears to be spontaneous.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2013

Regulatory Perspective on Potential Fuel Reconfiguration and Its Implication to High Burnup Spent Fuel Storage and Transportation - 13042

The recent experiments conducted by Argonne National Laboratory on high burnup fuel cladding material property show that the ductile to brittle transition temperature of high burnup fuel cladding is dependent on: (1) cladding material, (2) irradiation conditions, and (3) drying-storage histories (stress at maximum temperature) [1]. The experiment results also show that the ductile to brittle temperature increases as the fuel burnup increases. These results indicate that the current knowledge in cladding material property is insufficient to determine the structural performance of the cladding of high burnup fuel after it has been stored in a dry cask storage system for some time. The uncertainties in material property and the elevated ductile to brittle transition temperature impose a challenge to the storage cask and transportation packaging designs because the cask designs may not be able to rely on the structural integrity of the fuel assembly for control of fissile material, radiation source, and decay heat source distributions. The fuel may reconfigure during further storage and/or the subsequent transportation conditions. In addition, the fraction of radioactive materials available for release from spent fuel under normal condition of storage and transport may also change. The spent fuel storage and/or transportation packaging vendors, spent fuel shippers, and the regulator may need to consider this possible fuel reconfiguration and its impact on the packages' ability to meet the safety requirements of Part 72 and Part 71 of Title 10 of the Code of Federal Regulations. The United States Nuclear Regulatory Commission (NRC) is working with the scientists at Oak Ridge National Laboratory (ORNL) to assess the impact of fuel reconfiguration on the safety of the dry storage systems and transportation packages. The NRC Division of Spent Fuel Storage and Transportation has formed a task force to work on the safety and regulatory concerns in relevance to high burnup fuel storage and transportation. This paper discusses the staff's preliminary considerations on the safety implication of fuel reconfiguration with respect to nuclear safety (subcriticality control), radiation shielding, containment, the performance of the thermal functions of the packages, and the retrievability of the contents from regulatory perspective. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2016

Fission gas swelling in U{sub 3}Si{sub 2} at LWR conditions

In order to evaluate the feasibility of replacing uranium dioxide fuel with U{sub 3}Si{sub 2} fuel, it is crucial to examine the fuel performance of the silicide fuel under typical LWR conditions. At this early stage of U{sub 3}Si{sub 2} fuel development, before undertaking costly in-pile irradiation experiments and corresponding post-irradiation examinations, it is appropriate to utilize modeling tools to estimate the behavior of U{sub 3}Si{sub 2} in LWRs based on available in-pile irradiation experiments as well as the state-of-the-art calculation capabilities provided by density functional theory (DFT). Therefore, a comprehensive investigation of the fission gas swelling behavior of U{sub 3}Si{sub 2} at LWR conditions is reported here. The modeling efforts in this study are based on the Gas Release and Swelling Subroutine for Steady-State and Transient (GRASS-SST) rate theory (RT) model of fission gas bubble evolution that has been successfully applied to a variety of fuel materials in numerous types of reactors. Both existing in-pile irradiation data and DFT-based calculations were used for the optimized parametrization of the RT model. In addition, the fuel-cladding interaction was captured by coupling the RT model with simplified mechanical correlations. Both the swelling behavior and the fission gas bubble size distribution were predicted by the rate theory model. At LWR conditions, the RT model predicts that intragranular bubbles dominate the gaseous swelling behavior and that the evolution of intergranular bubbles and corresponding gas release are suppressed, confirming the qualification of U{sub 3}Si{sub 2} as a LWR fuel.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗