Search NASA⌕ Search

SEARCH · Search NASA

Results for “Graphite Properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

PPV derivative/ZnO nanorods heterojunction: Fabrication, Characterization and Near-UV light sensor development

Highlights: • We have fabricated a PPV-C6/ZnO NRs heterojunction by a simple and low cost method. • We have studied the structural and optical properties of the heterojunction. • I–V characteristics of EGa-In/Si/PPV-C6/ ZnO NRs /graphite devices were analyzed. • Photoelectrical study shows a potential opportunity for UV light sensor development. - Abstract: Poly(1,4-phenylenevinylene) derivative (PPV-C{sub 6}) based solution was spin-coated onto hydrothermally grown and vertically aligned ZnO nanorods (ZnO NRs).The morphological and the optical properties of the PPV-C{sub 6}/ZnO NRs hybrid heterojunction have been studied and shown a penetration of PPV-C{sub 6}into the interspaces between the ZnO NRs with enhanced excitonic dissociation. The current–voltage characteristics in dark and under 395 nm LED illumination have been analyzed. A short-circuit current J{sub sc} of 4691.42 μA/cm{sup 2}, an open-circuit voltage V{sub oc} of 0.46 V giving rise to a responsivity of about 29.32 mA/W have been obtained for the illuminated graphite/PPV-C6/ZnO NRs/Si/EGa-In structure based near UV light sensor showing an enhanced responsivity by a factor of about 200 compared with bare ZnO NRs based one. We have succeeded in the development of low cost near-UV light sensors by simple low temperature hydrothermal method using eco-friendly, low cost and easily fabricated electrodes.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Electronic and total energy properties of ternary and quaternary semiconductor compounds, alloys, and superlattices: Theoretical study of Cu/graphite bonding

The goals of the research were to provide a fundamental science basis for why the bonding of Cu to graphite is weak, to critically evaluate the previous analysis of the wetting studies with particular regard to the values used for the surface energies of Cu and graphite, and to make recommendations for future experiments or other studies which could advance the understanding and solution of this technological problem. First principles electronic structure calculations were used to study the problem. These are based on density functional theory in the local density approximation and the use of the linear muffin-tin orbital band structure method. Calculations were performed for graphite monolayers, single crystal graphite with the hexagonal AB stacking, bulk Cu, Cu(111) surface, and Cu/graphite superlattices. The study is limited to the basal plane of graphite because this is the graphite plane exposed to Cu and graphite surface energies and combined with the measured contact angles to evaluate the experimental adhesion energy.

Lambrecht, Walter R. L.↗

Ru(sub 2)Ge(sub 3): Crystal Growth and Come Properties

Large samples of Ru(sub 2)Ge(sub 3) were grown from Ge-rich off-stoichiometric melts at a temperature close to 1460 C by a vertical gradient freeze method in graphite and glassy carbon crucibles.

off-stoichiometric melt twinning crack formation h↗

Additively manufactured polymer composites for heat exchanger applications: evaluation of critical thermophysical properties

Polymeric heat exchangers (PHXs) have been used in applications involving weight restrictions, chemical compatibility, and fouling issues. Additive manufacturing (AM) or 3D printing provide new solutions to previously inaccessible combinations of properties and geometries. There are some advancements in the PHXs by AM; however, the process and the properties of materials still need further investigation to improve the overall performance. In this study, additively manufactured polyethylene terephthalate glycol (PETG) composites reinforced with graphite and pitch-based carbon fibers were evaluated for their potential application as PHXs. The thermal conductivity, volumetric heat capacity, coefficient of thermal expansion, creep behavior, and long-term performance were studied in detail. Our results reveal that the composites have an anisotropic thermal conductivity. The thermal conductivity along the printing direction is higher than the layer building direction due to the shear-induced alignment of the fillers. The printed composites achieve good thermal stability with 80% lower CTE at room temperature than neat PETG. Creep tests suggest the creep and creep recovery were highly temperature-dependent, and the deformation can be recovered when the temperature is below glass transition. These results suggest additive manufactured composites be potentially used for heat exchanger applications at low temperatures.

36 MATERIALS SCIENCE↗

Graphene sheets embedded carbon film prepared by electron irradiation in electron cyclotron resonance plasma

We used a low energy electron irradiation technique to prepare graphene sheets embedded carbon (GSEC) film based on electron cyclotron resonance plasma. The particular {pi} electronic structure of the GSEC film similar to bilayer graphene was verified by Raman spectra 2D band analyzing. The phase transition from amorphous carbon to GSEC was initiated when electron irradiation energy reached 40 eV, and the growth mechanism of GSEC was interpreted as inelastic scattering of low energy electrons. This finding indicates that the GSEC film obtained by low energy electron irradiation can be excepted for widely applications with outstanding electric properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Radiation Response of Low Dimensional Carbon Systems

The project is aimed at understanding the fundamentals of radiation response of low dimensional carbon systems and irradiation-induced mechanical property changes, with a focus on the unique phenomena caused by their geometry, boundary, and quantum size effects. In comparison with their bulk counterparts (graphite), radiation responses of low-dimensional carbon systems are substantially different. The differences exist at almost every stage of defect development, namely, displacement creation, damage cascade, thermal spike formation defect recombination, defect clustering, and structural reconstruction. Many traditional concepts in ion-solid interaction theory do not apply at the nanoscale or require substantial modification. Through this project, we systematically studied various aspects of radiation damage development in graphene, carbon nanotubes (CNTs), and graphite.

36 MATERIALS SCIENCE↗

Thermophysical characterization of composite materials under transient heating conditions

Thermophysical property measurements were made under transient heating conditions on several materials being considered for use in SCOUT rocket motors. The materials included were ATJ graphite, MX 2600 silica phenolic, FM 5272 cellulose phenolic, and two carbon-carbon composites: CARBITEX 700 and RPP-4. The ATJ was included as a reference or base line material to check performance of the transient tests as it was not expected to be sensitive to heating rate. Measurements included in the program were thermal conductivity, strength, compressive stress-strain (carbon-carbon only), thermal expansion and the effective thermal expansion under partially restrained conditions. Development of this latter measurement was a major part of the program. It consisted of partially restraining the expansion of a specimen as it was heated, measuring the load and strain which occurred (together with a simultaneous modulus determination by superimposing a small cyclic load) and using these quantities to calculate what the effective thermal expansion would have to be to produce the observed stress and deformation. For materials which are sensitive to heating rate, such as reinforced phenolics, it was believed that this would provide a more realistic determination of the thermal expansion as it more nearly simulates the conditions experienced in end use.

Roetling, J.↗

Numerical analysis and parametric studies of the buckling of composite orthotropic compression and shear panels

A computer program is presented which was developed for the combined compression and shear of stiffened variable thickness orthotropic composite panels on discrete springs: boundary conditions are general and include elastic boundary restraints. Buckling solutions are obtained by using a newly developed trigonometric finite difference procedure which improves the solution convergence rate over conventional finite difference methods. The classical general shear buckling results which exist only for simply supported panels over a limited range of orthotropic properties, were extended to the complete range of these properties for simply supported panels and, in addition, to the complete range of orthotropic properties for clamped panels. The program was also applied to parametric studies which examine the effect of filament orientation upon the buckling of graphite-epoxy panels. These studies included an examination of the filament orientations which yield maximum shear or compressive buckling strength for panels having all four edges simply supported or clamped over a wide range of aspect ratios. Panels with such orientations had higher buckling loads than comparable, equal weight, thin skinned aluminum panels. Also included among the parameter studies were examinations of combined axial compression and shear buckling and examinations of panels with rotational elastic edge restraints.

Housner, J. M.↗

Tribological properties of sintered polycrystalline and single crystal silicon carbide

Tribological studies and X-ray photoelectron spectroscopy analyses were conducted with sintered polycrystalline and single crystal silicon carbide surfaces in sliding contact with iron at various temperatures to 1500 C in a vacuum of 30 nPa. The results indicate that there is a significant temperature influence on both the friction properties and the surface chemistry of silicon carbide. The main contaminants on the as received sintered polycrystalline silicon carbide surfaces are adsorbed carbon, oxygen, graphite, and silicon dioxide. The surface revealed a low coefficient of friction. This is due to the presence of the graphite on the surface. At temperatures of 400 to 600 C graphite and copious amount of silicon dioxide were observed on the polycrystalline silicon carbide surface in addition to silicon carbide. At 800 C, the amount of the silicon dioxide decreased rapidly and the silicon carbide type silicon and carbon peaks were at a maximum intensity in the XPS spectra. The coefficients of friction were high in the temperature range 400 to 800 C. Small amounts of carbon and oxygen contaminants were observed on the as received single crystal silicon carbide surface below 250 C. Silicon carbide type silicon and carbon peaks were seen on the silicon carbide in addition to very small amount of graphite and silicon dioxide at temperatures of 450 to 800 C.

Miyoshi, K.↗

Styrene-terminated polysulfone oligomers as matrix material for graphite reinforced composites: An initial study

Styrene terminated polysulfone oligomers are part of an oligomeric class of compounds with end groups capable of thermal polymerization. These materials can be used as matrices for graphite reinforced composites. The initial evaluation of styrene terminated polysulfone oligomer based composites are summarized in terms of fabrication methods, and mechanical and environmental properties. In addition, a description and evaluation is provided of the NASA/Industry Fellowship Program for Technology Transfer.

Garcia, Dana↗

Thermo-oxidative stability studies of PMR-15 polymer matrix composites reinforced with various fibers

An experimental study was conducted to measure the thermo-oxidative stability of PMR-15 polymer matrix composites reinforced with various fibers and to observe differences in the way they degrade in air. The fibers that were studied included graphite and the thermally stable Nicalon and Nextel ceramic fibers. Weight loss rates for the different composites were assessed as a function of mechanical properties, specimen geometry, fiber sizing, and interfacial bond strength. Differences were observed in rates of weight loss, matrix cracking, geometry dependency, and fiber-sizing effects. It was shown that Celion 6000 fiber-reinforced composites do not exhibit a straight-line Arrhenius relationship at temperatures above 316 C.

Bowles, Kenneth J.↗

Polycrystalline SiC fibers from organosilicon polymers

Various organosilicon polymers have been converted into small diameter, fine-grained silicon carbide fibers by melt spinning, crosslinking, and pyrolyzing to greater than 1600 C. The high pyrolysis temperature densifies the fiber and causes CO evolution which removes nearly all oxygen. An additive prevents the loss of strength normally associated with such treatments. Silicon carbide fibres with up to 2.6 GPa (380 ksi) tensile strength, greater than 420 GPa (greater than 60 Msi) elastic modulus, and 3.1-3.2 mg/cu m density have been prepared via this process. Their microstructure consists of greater than 95 wt pct B-SiC crystallites averaging 30-40 nm diameter, with varying amounts of graphitic carbon between the SiC grains. Under inert conditions, the fibers can be thermally aged at least 12 h/1800 C with minimal change in properties.

Lipowitz, Jonathan↗

A manufacturing database of advanced materials used in spacecraft structures

Cost savings opportunities over the life cycle of a product are highest in the early exploratory phase when different design alternatives are evaluated not only for their performance characteristics but also their methods of fabrication which really control the ultimate manufacturing costs of the product. In the past, Design-To-Cost methodologies for spacecraft design concentrated on the sizing and weight issues more than anything else at the early so-called 'Vehicle Level' (Ref: DOD/NASA Advanced Composites Design Guide). Given the impact of manufacturing cost, the objective of this study is to identify the principal cost drivers for each materials technology and propose a quantitative approach to incorporating these cost drivers into the family of optimization tools used by the Vehicle Analysis Branch of NASA LaRC to assess various conceptual vehicle designs. The advanced materials being considered include aluminum-lithium alloys, thermoplastic graphite-polyether etherketone composites, graphite-bismaleimide composites, graphite- polyimide composites, and carbon-carbon composites. Two conventional materials are added to the study to serve as baseline materials against which the other materials are compared. These two conventional materials are aircraft aluminum alloys series 2000 and series 7000, and graphite-epoxy composites T-300/934. The following information is available in the database. For each material type, the mechanical, physical, thermal, and environmental properties are first listed. Next the principal manufacturing processes are described. Whenever possible, guidelines for optimum processing conditions for specific applications are provided. Finally, six categories of cost drivers are discussed. They include, design features affecting processing, tooling, materials, fabrication, joining/assembly, and quality assurance issues. It should be emphasized that this database is not an exhaustive database. Its primary use is to make the vehicle designer aware of some of the most important aspects of manufacturing associated with his/her choice of the structural materials. The other objective of this study is to propose a quantitative method to determine a Manufacturing Complexity Factor (MCF) for each material being contemplated. This MCF is derived on the basis of the six cost drivers mentioned above plus a Technology Readiness Factor which is very closely related to the Technology Readiness Level (TRL) as defined in the Access To Space final report. Short of any manufacturing information, our MCF is equivalent to the inverse of TRL. As more manufacturing information is available, our MCF is a better representation (than TRL) of the fabrication processes involved. The most likely application for MCF is in cost modeling for trade studies. On-going work is being pursued to expand the potential applications of MCF.

Bao, Han P.↗

Poco Graphite Inc. SuperSiC 0.25m Mirror Cryogenic Test Result

SuperSiC, a low areal density material, developed by POCO Graphite, have been used as mirror substrate for high energy lasers, laser radar systems, surveillance, telescopes, scan mirrors and satellites. SuperSiC has excellent thermal properties and cryogenic stability. It exhibits exceptional polishability for reflective optics with high strength, stiffness, and excellent thermal conductivity. A lightweighted 0.2-diameter polished SuperSic mirror was tested at cryogenic temperature at NASMSFC. Optical test results showed 6nm cry0 deformation from ambient to 30 degrees Kelvin and little to no change in its surface figure due to cry0 cycling.

Eng, Ron↗

Lunar and Planetary Science XXXVI, Part 10

The Problem of Incomplete Mixing of Interstellar Components in the Solar Nebula: Very High Precision Isotopic Measurements with Isoprobes P and T. Finally: Presolar Graphite Grains Identified in Orgueil. Basaltic Ring Structures as an Analog for Ring Features in Athabasca Valles, Mars. Experimental Studies of the Water Sorption Properties of Mars-Relevant Porous Minerals and Sulfates. Silicon Isotope Ratio Variations in CAI Evaporation Residues Measured by Laser Ablation Multicollector ICPMS. Crater Count Chronology and Timing of Ridged Plains Emplacement at Schiaparelli Basin, Mars. Martian Valley Networks and Associated Fluvial Features as Seen by the Mars Express High Resolution Stereo Camera (HRSC). Fast-Turnoff Transient Electromagnetic (TEM) Field Study at the Mars Analog Site of Rio Tinto, Spain. Time Domain Electromagnetics for Mapping Mineralized and Deep Groundwater in Mars Analog Environments. Mineralogical and Seismological Models of the Lunar Mantle. Photometric Observations of Soils and Rocks at the Mars Exploration Rover Landing Sites. Thermal Infrared Spectral Deconvolution of Experimentally Shocked Basaltic Rocks Using Experimentally Shocked Plagioclase Endmembers.

Source record↗

Advanced Materials and Fabrication Techniques for the Orion Attitude Control Motor

Rhenium, with its high melting temperature, excellent elevated temperature properties, and lack of a ductile-to-brittle transition temperature (DBTT), is ideally suited for the hot gas components of the ACM (Attitude Control Motor), and other high-temperature applications. However, the high cost of rhenium makes fabricating these components using conventional fabrication techniques prohibitive. Therefore, near-net-shape forming techniques were investigated for producing cost-effective rhenium and rhenium alloy components for the ACM and other propulsion applications. During this investigation, electrochemical forming (EL-Form ) techniques were evaluated for producing the hot gas components. The investigation focused on demonstrating that EL-Form processing techniques could be used to produce the ACM flow distributor. Once the EL-Form processing techniques were established, a representative rhenium flow distributor was fabricated, and samples were harvested for material properties testing at both room and elevated temperatures. As a lower cost and lighter weight alternative to an all-rhenium component, rhenium- coated graphite and carbon-carbon were also evaluated. The rhenium-coated components were thermal-cycle tested to verify that they could withstand the expected thermal loads during service. High-temperature electroforming is based on electrochemical deposition of compact layers of metals onto a mandrel of the desired shape. Mandrels used for electro-deposition of near-net shaped parts are generally fabricated from high-density graphite. The graphite mandrel is easily machined and does not react with the molten electrolyte. For near-net shape components, the inner surface of the electroformed part replicates the polished graphite mandrel. During processing, the mandrel itself becomes the cathode, and scrap or refined refractory metal is the anode. Refractory metal atoms from the anode material are ionized in the molten electrolytic solution, and are deposited onto the cathodic mandrel by electrochemical reduction. Rotation of the mandrel ensures uniform distribution of refractory material. The EL-Form process allows for manufacturing in an inert atmosphere with deposition rates from 0.0004 to 0.002 in./h (10.2 to 50.8 m/h). Thicknesses typically range from microns to greater than 0.5 in. (13 mm). The refractory component produced is fabricated, dependably, to within one micron of the desired tolerances with no shrinkage or distortion as in other refractory metal manufacture techniques. The electroforming process has been used to produce solid, nonporous deposits of rhenium, iridium, niobium, tungsten, and their alloys.

Gorti, Sridhar↗

NanoMechanics: Elasticity and Friction in Nano‐Objects

A large scientific and technological effort is underway to investigate the properties of two‐dimensional (2D) materials to become building blocks in integrated nano‐electronic and photonic circuits, composites, coatings, energy harvesting nano‐ systems, nano‐sensors, and nano‐electro‐mechanical systems (NEMS).While several experiments and calculations have revealed exciting novel phenomena in these nanostructures, many scientific and technological questions remain open. In particular, understanding and controlling the structure and mechanical properties of 2D materials at the interface with a solid surface is of key importance to enable the aforementioned nanotechnologies, as well as to fulfill the potential of strain engineering to tailor their properties. The vision of this DoE research program was to investigate novel mechanical properties and phenomena in 1D and 2D materials with the overarching goal of defining a new basic understanding of mechanical behavior in nano and quantum systems. The group of the PI has developed in the last years several studies on the mechanical properties of Carbon nanotubes and oxide nanobelts, more recently the PI has focused her attention on the properties of two‐dimensional materials, such as graphene and MoS 2 , which are a few‐atomic‐layer thick films and hold a great potential for technological and energy applications. The most studied 2D material is graphene, existing as a single layer of graphite or a few‐layer thick epitaxial graphene film. Graphene possesses a large in‐plane Young’s modulus as well as high intrinsic carrier mobility, and high in‐plane thermal conductivity. Besides graphene, also 2D films of graphene oxide (GO), hexagonal Boron Nitride (h‐BN), and transition metal dichalcogenides such as MoS 2 exhibit unique and excellent properties and hold great promise for nanotechnology applications. This research program was aimed at developing a new basic understanding of the mechanical properties of 1D and 2D materials at the interface with solid substrates, with a focus on the role of defects, materials structure, and substrate interaction. Ultimately, we aimed at developing the basic knowledge and experimental tools for manipulating 1D and 2D materials’ structure, stacking, substrate interaction, defects, and number of layers to realize an entirely new class of ultra‐hard, ultra‐thin, and ultra‐light active materials with ad‐ hoc mechanical properties for a variety of applications.

2D Materials↗

Hard graphitelike hydrogenated amorphous carbon grown at high rates by a remote plasma

Hydrogenated amorphous carbon (a-C:H) deposited from an Ar-C{sub 2}H{sub 2} expanding thermal plasma chemical vapor deposition (ETP-CVD) is reported. The downstream plasma region of an ETP is characterized by a low electron temperature ({approx}0.3 eV), which leads to an ion driven chemistry and negligible physical effects, such as ion bombardment (ion energy <2 eV) on the depositing surface. The material properties in ETP-CVD can be controlled by varying the plasma chemistry. In this article we investigate the change in a-C:H material properties by varying the Ar/C{sub 2}H{sub 2} gas flow ratio over a wide range (1.33-150), with emphasis on low gas flow ratios (1.33-5). By changing the Ar/C{sub 2}H{sub 2} gas flow ratio, the gas residence time in the ETP expansion can be tuned, which in turn defines the chemistry of the ETP-CVD. Soft polymerlike a-C:H to moderately hard a-C:H films have been deposited by lowering the Ar/C{sub 2}H{sub 2} gas flow ratio. Recently, under very low Ar/C{sub 2}H{sub 2} gas flow ratios, a hard graphitelike a-C:H material has been deposited. The striking feature of this material is the infrared absorption spectrum in the C-H{sub x} stretching region (2800-3100 cm{sup -1}), which is a distinct narrow bimodal spectrum evolving from a broad spectrum for the moderately hard a-C:H. This transition was attributed to the absence of end groups (sp{sup 2} CH{sub 2} and sp{sup 3} CH{sub 3}), which favors an enhanced cross-linking in the film in a similar effect to elevated ion bombardment or annealing. Moreover, the hard graphitelike film has an increased refractive index (n) as high as 2.5 at 633 nm with a corresponding mass density of {approx}2.0 g/cm{sup 3}.

36 MATERIALS SCIENCE↗