Search NASA⌕ Search

SEARCH · Search NASA

Results for “High Speed Data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

Numerical Analysis of a Radiant Heat Flux Calibration System

A radiant heat flux gage calibration system exists in the Flight Loads Laboratory at NASA's Dryden Flight Research Center. This calibration system must be well understood if the heat flux gages calibrated in it are to provide useful data during radiant heating ground tests or flight tests of high speed aerospace vehicles. A part of the calibration system characterization process is to develop a numerical model of the flat plate heater element and heat flux gage, which will help identify errors due to convection, heater element erosion, and other factors. A 2-dimensional mathematical model of the gage-plate system has been developed to simulate the combined problem involving convection, radiation and mass loss by chemical reaction. A fourth order finite difference scheme is used to solve the steady state governing equations and determine the temperature distribution in the gage and plate, incident heat flux on the gage face, and flat plate erosion. Initial gage heat flux predictions from the model are found to be within 17% of experimental results.

Jiang, Shanjuan↗

Status of the Validation of High-Angle-Of-Attack Nose-Down Pitch Control Margin Design Guidelines

This paper presents a summary of results obtained to date in an ongoing cooperative research program between NASA and the U.S. Navy to develop design criteria for high-angle-of-attack nose- down pitch control for combat aircraft. A fundamental design consideration for aircraft incorporating relaxed static stability in pitch is the level of stability which achieves a proper balance between high- speed performance considerations and low-speed requirements for maneuvering at high angles of attack. A comprehensive data base of piloted simulation results was generated for parametric variations of critical parameters affecting nose-down control capability. The results showed a strong correlation of pilot rating to the short-term pitch response for nose-down commands applied at high- angle-of-attack conditions. Using these data, candidate design guidelines and flight demonstration requirements were defined. Full- scale flight testing to validate the research methodology and proposed guidelines is in progress, some preliminary results of which are reviewed.

Ogburn, Marilyn E.↗

The Effect of Compressibility on the Growth of the Laminar Boundary Layer on Low-Drag Wings and Bodies

The development of the laminar boundary layer in a compressible fluid is considered. Formulas are given for determining the boundary-layer thickness and the ratio of the boundary-layer Reynolds number to the body Reynolds number for airfoils and bodies of revolution. It i s shown that the effect of compressibility will profoundly alter the Reynolds number corresponding to the upper limit of the range of the low-drag coefficients . The available data indicate that for low-drag and high critical compressibility speed airfoils and bodies of revolution, this effect is favorable.

Allen, H. Julian↗

Fan Noise Predictions of the NASA Source Diagnostic Test Using Unsteady Simulations with LAVA Part I: Near-Field Aerodynamics and Turbulence

A sliding mesh technique within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework is validated using the experimental dataset collected as part of the NASA Source Diagnostic Test (SDT) campaign. Two modeling approaches are explored: the unsteady Reynolds-Averaged Navier Stokes (URANS) with Spalart-Allmaras (SA) turbulence model closure, and a hybrid Reynolds-Averaged Navier Stokes/Large Eddy Simulation (RANS/LES) paradigm employing a Zonal Detached Eddy Simulation (ZDES) closure with enhanced shielding protection. Fan stage performance metrics, aerodynamic quantities and turbulent flow structures are analyzed in this work. Initial studies focusing on grid and time-step sensitivity are presented. Sensitivity to different variants of the SA turbulence model is analyzed, supporting the use of the baseline SA model in the production runs. Two conditions are analyzed in detail using URANS and hybrid RANS/LES (HRLES). Mean flow quantities are well-captured by both methods in the low-speed (approach) regime. While URANS misses all the upstream-propagating noise in the inlet due to the rotor-locked tones being evanescent in nature at subsonic fan tip speeds, HRLES captures this broadband component in its pressure field. At the high-speed (sideline) condition, URANS shows better agreement with the SDT data than HRLES in the interstage flow-field. In this regime, URANS captures the tonal content propagating through the inlet, since the tones are now cut-on. Both methods are suitable to capture fan stage performance metrics and mean flow quantities, but only HRLES is able to resolve the fine turbulent structures responsible for broadband noise. The results support the use of the sliding mesh technique implemented in this work for future turbomachinery applications within the LAVA solver framework.

AATT↗

Fan Noise Predictions of the NASA Source Diagnostic Test Using Unsteady Simulations with LAVA Part I: Near-Field Aerodynamics and Turbulence

A sliding mesh technique within the Launch, Ascent, and Vehicle Aerodynamics (LAVA) computational framework is validated using the experimental dataset collected as part of the NASA Source Diagnostic Test (SDT) campaign. Two modeling approaches are explored: the unsteady Reynolds-Averaged Navier Stokes (URANS) with Spalart-Allmaras (SA) turbulence model closure, and a hybrid Reynolds-Averaged Navier Stokes/Large Eddy Simulation (RANS/LES) paradigm employing a Zonal Detached Eddy Simulation (ZDES) closure with enhanced shielding protection. Fan stage performance metrics, aerodynamic quantities and turbulent flow structures are analyzed in this work. Initial studies focusing on grid and time-step sensitivity are presented. Sensitivity to different variants of the SA turbulence model is analyzed, supporting the use of the baseline SA model in the production runs. Two conditions are analyzed in detail using URANS and hybrid RANS/LES (HRLES). Mean flow quantities are well-captured by both methods in the low-speed (approach) regime. While URANS misses all the upstream-propagating noise in the inlet due to the rotor-locked tones being evanescent in nature at subsonic fan tip speeds, HRLES captures this broadband component in its pressure field. At the high-speed (sideline) condition, URANS shows better agreement with the SDT data than HRLES in the interstage flow-field. In this regime, URANS captures the tonal content propagating through the inlet, since the tones are now cut-on. Both methods are suitable to capture fan stage performance metrics and mean flow quantities, but only HRLES is able to resolve the fine turbulent structures responsible for broadband noise. The results support the use of the sliding mesh technique implemented in this work for future turbomachinery applications within the LAVA solver framework.

AATT↗

Advance Reservation Access Control Using Software-Defined Networking and Tokens

Advance reservation systems allow users to reserve dedicated bandwidth connection resources from an advanced high-speed network. A common use case for such systems is data transfers in distributed science environments in which a user wants exclusive access to the reservation. However, current advance network reservation methods cannot ensure exclusive access of a network reservation to the specific flow for which the user made the reservation. We present here a novel network architecture that addresses this limitation and ensures that a reservation is used only by the intended flow. We achieve this by leveraging software-defined networking (SDN) and token-based authorization. We use SDN to orchestrate and automate the reservation of networking resources, end-to-end and across multiple administrativedomains, and tokens to create a strong binding between the user or application that requested the reservation and the flows provisioned by SDN.

Kettimuthu, R.↗

Experimental Space Shuttle Orbiter Studies to Acquire Data for Code and Flight Heating Model Validation

In an experimental study to obtain detailed heating data over the Space Shuttle Orbiter, CUBRC has completed an extensive matrix of experiments using three distinct models and two unique hypervelocity wind tunnel facilities. This detailed data will be employed to assess heating augmentation due to boundary layer transition on the Orbiter wing leading edge and wind side acreage with comparisons to computational methods and flight data obtained during the Orbiter Entry Boundary Layer Flight Experiment and HYTHIRM during STS-119 reentry. These comparisons will facilitate critical updates to be made to the engineering tools employed to make assessments about natural and tripped boundary layer transition during Orbiter reentry. To achieve the goals of this study data was obtained over a range of Mach numbers from 10 to 18, with flight scaled Reynolds numbers and model attitudes representing key points on the Orbiter reentry trajectory. The first of these studies were performed as an integral part of Return to Flight activities following the accident that occurred during the reentry of the Space Shuttle Columbia (STS-107) in February of 2003. This accident was caused by debris, which originated from the foam covering the external tank bipod fitting ramps, striking and damaging critical wing leading edge heating tiles that reside in the Orbiter bow shock/wing interaction region. During investigation of the accident aeroheating team members discovered that only a limited amount of experimental wing leading edge data existed in this critical peak heating area and a need arose to acquire a detailed dataset of heating in this region. This new dataset was acquired in three phases consisting of a risk mitigation phase employing a 1.8% scale Orbiter model with special temperature sensitive paint covering the wing leading edge, a 0.9% scale Orbiter model with high resolution thin-film instrumentation in the span direction, and the primary 1.8% scale Orbiter model with detailed thin-film resolution in both the span and chord direction in the area of peak heating. Additional objectives of this first study included: obtaining natural or tripped turbulent wing leading edge heating levels, assessing the effectiveness of protuberances and cavities placed at specified locations on the orbiter over a range of Mach numbers and Reynolds numbers to evaluate and compare to existing engineering and computational tools, obtaining cavity floor heating to aid in the verification of cavity heating correlations, acquiring control surface deflection heating data on both the main body flap and elevons, and obtain high speed schlieren videos of the interaction of the orbiter nose bow shock with the wing leading edge. To support these objectives, the stainless steel 1.8% scale orbiter model in addition to the sensors on the wing leading edge was instrumented down the windward centerline, over the wing acreage on the port side, and painted with temperature sensitive paint on the starboard side wing acreage. In all, the stainless steel 1.8% scale Orbiter model was instrumented with over three-hundred highly sensitive thin-film heating sensors, two-hundred of which were located in the wing leading edge shock interaction region. Further experimental studies will also be performed following the successful acquisition of flight data during the Orbiter Entry Boundary Layer Flight Experiment and HYTHIRM on STS-119 at specific data points simulating flight conditions and geometries. Additional instrumentation and a protuberance matching the layout present during the STS-119 boundary layer transition flight experiment were added with testing performed at Mach number and Reynolds number conditions simulating conditions experienced in flight. In addition to the experimental studies, CUBRC also performed a large amount of CFD analysis to confirm and validate not only the tunnel freestream conditions, but also 3D flows over the orbiter acreage, wing leading edge, and controlurfaces to assess data quality, shock interaction locations, and control surface separation regions. This analysis is a standard part of any experimental program at CUBRC, and this information was of key importance for post-test data quality analysis and understanding particular phenomena seen in the data. All work during this effort was sponsored and paid for by the NASA Space Shuttle Program Office at the Johnson Space Center in Houston, Texas.

Wadhams, T. P.↗

A User Guide for Smoothing Air Traffic Radar Data

Matlab software was written to provide smoothing of radar tracking data to simulate ADS-B (Automatic Dependent Surveillance-Broadcast) data in order to test a tactical conflict probe. The probe, called TSAFE (Tactical Separation-Assured Flight Environment), is designed to handle air-traffic conflicts left undetected or unresolved when loss-of-separation is predicted to occur within approximately two minutes. The data stream that is down-linked from an aircraft equipped with an ADS-B system would include accurate GPS-derived position and velocity information at sample rates of 1 Hz. Nation-wide ADS-B equipage (mandated by 2020) should improve surveillance accuracy and TSAFE performance. Currently, position data are provided by Center radar (nominal 12-sec samples) and Terminal radar (nominal 4.8-sec samples). Aircraft ground speed and ground track are estimated using real-time filtering, causing lags up to 60 sec, compromising performance of a tactical resolution tool. Offline smoothing of radar data reduces wild-point errors, provides a sample rate as high as 1 Hz, and yields more accurate and lag-free estimates of ground speed, ground track, and climb rate. Until full ADS-B implementation is available, smoothed radar data should provide reasonable track estimates for testing TSAFE in an ADS-B-like environment. An example illustrates the smoothing of radar data and shows a comparison of smoothed-radar and ADS-B tracking. This document is intended to serve as a guide for using the smoothing software.

Center/Tracon Radar↗

EMPIRICAL DETERMINATION OF CONVECTION PARAMETERS IN WHITE DWARFS. I. WHOLE EARTH TELESCOPE OBSERVATIONS OF EC14012-1446

We report on an analysis of 308.3 hr of high-speed photometry targeting the pulsating DA white dwarf EC14012-1446. The data were acquired with the Whole Earth Telescope during the 2008 international observing run XCOV26. The Fourier transform of the light curve contains 19 independent frequencies and numerous combination frequencies. The dominant peaks are 1633.907, 1887.404, and 2504.897 {mu}Hz. Our analysis of the combination amplitudes reveals that the parent frequencies are consistent with modes of spherical degree l = 1. The combination amplitudes also provide m identifications for the largest amplitude parent frequencies. Our seismology analysis, which includes 2004-2007 archival data, confirms these identifications, provides constraints on additional frequencies, and finds an average period spacing of 41 s. Building on this foundation, we present nonlinear fits to high signal-to-noise light curves from the SOAR 4.1 m, McDonald 2.1 m, and KPNO 2 m telescopes. The fits indicate a time-averaged convective response timescale of {tau}{sub 0} = 99.4 {+-} 17 s, a temperature exponent N = 85 {+-} 6.2, and an inclination angle of {theta}{sub i} = 32.{sup 0}9 {+-} 3.{sup 0}2. We present our current empirical map of the convective response timescale across the DA instability strip.

79 ASTRONOMY AND ASTROPHYSICS↗

The February 1986 solar activity - A comparison of Giotto, Vega-1, and IMP-8 solar wind measurements with MHD simulations

Large disturbances in the interplanetary medium were observed by several spacecraft during a period of enhanced solar activity in early February 1986. The locations of six solar flares and the spacecraft considered here encompassed more than 100 deg of heliolongitude. These flares during the minimum of cycle 21 set the stage for an extensive multispacecraft comparison performed with a two-dimensional, MHD numerical experiment. The plasma instruments on the Giotto spacecraft, on its way to encounter Comet Halley in March 1986, made measurements of the solar wind for up to 8 hours/day during February. Solar wind measurements from the Johnstone Plasma Analyzer experiment on Giotto are compared with the MHD simulation of the interplanetary medium throughout these events. Using plasma data obtained by the IMP-8 satellite in addition, it appears that an extended period of high solar wind speed is required as well as the simulated flares to represent the interplanetary medium in this case. The plasma and magnetometer data from Vega-1 is compared with the MHD simulation. This comparison tends to support an interpretation that the major solar wind changes at both Giotto and Vega-1 on February 8, 1986 were due to a shock from a W 05 deg solar flare on February 6, 1986 (06:25 UT). The numerical experiment is considered, qualitatively, to resemble the observations at the former spacecraft, but it has less success at the latter one.

Dryer, M.↗

Developing a 20-year high-resolution wind data set for Puerto Rico

The purpose of this study is to develop a high-resolution wind resource data set for Puerto Rico as part of the wind resource assessment in the Puerto Rico Grid Resilience and Transition to 100 % Renewable Energy Study (PR100) project. The Weather and Research and Forecasting (WRF) is used to model 20-years (2001-2020) of wind resource data on a 3-km grid for the Puerto Rico region. Because accurately representing the planetary boundary layer (PBL)-physics in the WRF is key to accurately model low-level wind speed, 11 different PBL schemes are examined and evaluated to find a WRF configuration that can provide the most accurate wind data. The modeled wind speeds are validated with buoy observations, and the Shin-Hong PBL scheme is selected to generate the final wind data set. Here, the overall results demonstrate that the high-resolution data correctly represents the climate of Puerto Rico (e.g., a dominant easterly trade wind). At 160 m above ground, the southern regions of Puerto Rico show strong offshore wind speed (>8 m/s on average) throughout the daytime and nighttime. For land-based wind, average wind speed ranges from 5 m/s-7 m/s during daytime, whereas notable high wind speeds (>9 m/s) appear in the mountain regions during nighttime.

17 WIND ENERGY↗

Secure Large-Scale Airport Simulations Using Distributed Computational Resources

To fully conduct research that will support the far-term concepts, technologies and methods required to improve the safety of Air Transportation a simulation environment of the requisite degree of fidelity must first be in place. The Virtual National Airspace Simulation (VNAS) will provide the underlying infrastructure necessary for such a simulation system. Aerospace-specific knowledge management services such as intelligent data-integration middleware will support the management of information associated with this complex and critically important operational environment. This simulation environment, in conjunction with a distributed network of supercomputers, and high-speed network connections to aircraft, and to Federal Aviation Administration (FAA), airline and other data-sources will provide the capability to continuously monitor and measure operational performance against expected performance. The VNAS will also provide the tools to use this performance baseline to obtain a perspective of what is happening today and of the potential impact of proposed changes before they are introduced into the system.

McDermott, William J.↗

On Performance Prediction of Big Data Transfer in High-performance Networks

Big data generated by large-scale scientific and industrial applications need to be transferred between different geographical locations for remote storage, processing, and analysis. High-speed dedicated connections provisioned in High-performance Networks (HPNs) are increasingly utilized to carry out such big data transfer. HPN management highly relies on an important capability of performance (mainly throughput) prediction to reserve sufficient bandwidth and meanwhile avoid over-provisioning that may result in unnecessary resource waste. This capability is critical to improving the resource (mainly bandwidth) utilization of dedicated connections and meeting various user requests for data transfer. Conventional methods conduct performance prediction by fitting prior observed transfer history with predefined loss functions, without considering unobservable latent factors such as competing loads on end hosts. Such latent factors also have a significant impact on the application-level data transfer performance, which may result in an inaccurate prediction model. In this paper, we first investigate the impact of latent factors and propose a clustering-based method to eliminate their negative impact on performance prediction. We then develop a robust machine learning-based performance predictor by: i) incorporating the proposed latent factor elimination method into data preprocessing, and ii) adopting a customized domain guided loss function. Extensive experimental results show that our predictor achieves significantly higher prediction accuracy than several other state-of-the-art methods.

Liu, Wuji↗

TDRSS Augmentation for Launch and Ascent High Speed Navigation Filter

An investigation was performed to evaluate the feasibility and possible advantages of augmenting the High Speed Trajectory Determination (HSTD) ground navigation filter with measurements from the Tracking & Data Relay Satellite System (TDRSS) constellation. The proposed communications system strategy for Constellation uses TDRSS rather than ground S-band, so the capability of replacing the S-band navigation capability with TDRSS was considered. HSTD simulations were performed with combinations of S-band, C-band, and TDRSS measurements. Several assumptions are made with regard to measurement biases and signal noise characteristics to produce first-look level accuracies. Preliminary results show that solutions using TDRSS instead of S-band have similar or improved performance from the view of filter covariance and may be a feasible alternative. These results also show that TDRSS tracking alone gives poorer observations and resulting performance Operational and other constraints to the use of TDRSS in a high-speed ground navigation filter are not addressed.

Holt, Greg .↗

Low-speed aerodynamic characteristics of a 0.08-scale YF-17 airplane model at high angles of attack and sideslip

Data were obtained with and without the nose boom and with several strake configurations; also, data were obtained for various control surface deflections. Analysis of the results revealed that selected strake configurations adequately provided low Reynolds number simulation of the high Reynolds number characteristics. The addition of the boom in general tended to reduce the Reynolds number effects.

Petroff, D. N.↗

High speed VLSI systems for NASA's telemetry return link processor

This paper describes the architecture of the Data Interface Facility, (DIF), a key element in NASA's advanced communications systems, and its core element, the Return Link Processor (RLP). Current activities to prototype some of the primary functions of the RLP are presented. It is shown how the prototype elements can be integrated into a full-performance DIF RLP.

Hand, Sarah L.↗

COOP 3D ARPA Experiment 109 National Center for Atmospheric Research

Coupled atmospheric and hydrodynamic forecast models were executed on the supercomputing resources of the National Center for Atmospheric Research (NCAR) in Boulder, Colorado and the Ohio Supercomputing Center (OSC)in Columbus, Ohio. respectively. The interoperation of the forecast models on these geographically diverse, high performance Cray platforms required the transfer of large three dimensional data sets at very high information rates. High capacity, terrestrial fiber optic transmission system technologies were integrated with those of an experimental high speed communications satellite in Geosynchronous Earth Orbit (GEO) to test the integration of the two systems. Operation over a spacecraft in GEO orbit required modification of the standard configuration of legacy data communications protocols to facilitate their ability to perform efficiently in the changing environment characteristic of a hybrid network. The success of this performance tuning enabled the use of such an architecture to facilitate high data rate, fiber optic quality data communications between high performance systems not accessible to standard terrestrial fiber transmission systems. Thus obviating the performance degradation often found in contemporary earth/satellite hybrids.

Source record↗

An expert system to analyze high frequency dependent data for the space shuttle main engine turbopumps

The prototype expert system ADDAMX identifies selected sinusoid frequencies from spectral data graphs as speed frequencies and harmonics from each turbopump, frequency feed through from one turbopump to another, frequencies generated by turbopump bearings, pseudo 3N for the phase 2 high pressure fuel turbopump, and electrical noise. ADDAMX does the analysis in an interactive or batch mode and the results can be displayed on the screen or hardcopy.

Garcia, Raul C., Jr.↗