Search NASA⌕ Search

SEARCH · Search NASA

Results for “Method”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

The application of a second generation low-order panel method - program 'Vsaero' - to powerplant installation studies

Results from the application of a second generation low-order panel method to a number of powerplant installations are presented. The method, which retains the advantages of ease of use and low operating cost of earlier panel methods while retaining the aerodynamic modelling rigor of higher-order methods was used to predict the flow in and around typical nacelles and aircraft for a wide range of conditions. The ability of the second generation low-order analysis to calculate internal flows without the leakage problems associated with earlier programs is demonstrated and correlation between calculated and measured surface pressures and flow behavior, including predicting streamlines and locating regions of separated flow, is presented.

Clark, D. R.↗

A method for modeling finite-core vortices in wake-flow calculations

A numerical method for computing nonplanar vortex wakes represented by finite-core vortices is presented. The approach solves for the velocity on an Eulerian grid, using standard finite-difference techniques; the vortex wake is tracked by Lagrangian methods. In this method, the distribution of continuous vorticity in the wake is replaced by a group of discrete vortices. An axially symmetric distribution of vorticity about the center of each discrete vortex is used to represent the finite-core model. Two distributions of vorticity, or core models, are investigated: a finite distribution of vorticity represented by a third-order polynomial, and a continuous distribution of vorticity throughout the wake. The method provides for a vortex-core model that is insensitive to the mesh spacing. Results for a simplified case are presented. Computed results for the roll-up of a vortex wake generated by wings with different spanwise load distributions are presented; contour plots of the flow-field velocities are included; and comparisons are made of the computed flow-field velocities with experimentally measured velocities.

Stremel, P. M.↗

Relaxation methods for unfactored implicit upwind schemes

Relaxation methods are presented for unfactored implicit upwind schemes for hyperbolic equations. The theoretical bases are explained using linear and nonlinear scalar equations; construction of the method for the unsteady Euler equations (nonlinear system) is but a natural extension. One of the important advantages of the above methods vis a vis factored implicit schemes is the possibility of faster convergence to steady state, as illustrated by the results. Several classes of relaxation schemes such as pointwise, linewise, Gauss-Seidel, and non-Gauss-Seidel methods are discussed, along with various strategies for convergence.

Chakravarthy, S. R.↗

A comparison between GO/aperture-field and physical-optics methods for offset reflectors

Both geometrical optics (GO)/aperture-field and physical-optics (PO) methods are used extensively in the diffraction analysis of offset parabolic and dual reflectors. An analytical/numerical comparative study is performed to demonstrate the limitations of the GO/aperture-field method for accurately predicting the sidelobe and null positions and levels. In particular, it is shown that for offset parabolic reflectors and for feeds located at the focal point, the predicted far-field patterns (amplitude) by the GO/aperture-field method will always be symmetric even in the offset plane. This, of course, is inaccurate for the general case and it is shown that the physical-optics method can result in asymmetric patterns for cases in which the feed is located at the focal point. Representative numerical data are presented and a comparison is made with available measured data.

Rahmat-Samii, Y.↗

A new explicit method for the numerical solution of parabolic differential equations

A new method is derived for solving parabolic partial differential equations arising in transient heat conduction or in boundary-layer flows. The method is based on a combination of the modified differential quadrature (MDQ) method with the rational Runge-Kutta time-integration scheme. It is fully explicit, requires no matrix inversion, and is stable for any time-step for the heat equations. Burgers equation and the one- and two-dimensional heat equations are solved to demonstrate the accuracy and efficiency of the proposed algorithm. The present method is found to be very accurate and efficient when results are compared with analytic solutions.

Satofuka, N.↗

Application of an optimization method to high performance propeller designs

The application of an optimization method to determine the propeller blade twist distribution which maximizes propeller efficiency is presented. The optimization employs a previously developed method which has been improved to include the effects of blade drag, camber and thickness. Before the optimization portion of the computer code is used, comparisons of calculated propeller efficiencies and power coefficients are made with experimental data for one NACA propeller at Mach numbers in the range of 0.24 to 0.50 and another NACA propeller at a Mach number of 0.71 to validate the propeller aerodynamic analysis portion of the computer code. Then comparisons of calculated propeller efficiencies for the optimized and the original propellers show the benefits of the optimization method in improving propeller performance. This method can be applied to the aerodynamic design of propellers having straight, swept, or nonplanar propeller blades.

Li, K. C.↗

Synthesized airfoil data method for prediction of dynamic stall and unsteady airloads

The synthesized unsteady airfoil data method, which accurately describes the unsteady aerodynamic characteristics of stalled airfoils in the time domain, is expanded and improved. Nine sets of unsteady drag data are synthesized, providing a basis for the successful expansion of the method to include the computation of unsteady pressure drag of airfoils and rotor blades. An improved prediction model for airfoil flow reattachment is incorporated into the method. Application of the model results in a better correlation of analytic predictions with measured full-scale helicopter blade loads and stress data. The results show that it is feasible to generalize the empirical parameters embedded in the method over a range of angles of attack, Mach number, airfoil shape, and sweep angle.

Gangwani, S. T.↗

A statistical correlation method for the retrieval of atmospheric moisture profiles by microwave radiometry

A statistical correlation technique is applied to the retrieval of vertical moisture profiles under clear-sky conditions from down-looking radiometric measurements of atmospheric radiation at microwave wavelengths. For a given set of channels, the method selects the optimum radiometric channels for estimating water vapor at specific pressure levels between the surface and 300 mb. The water vapor mixing ratio at these pressure levels is then calculated from a linear combination of the selected channel brightness temperatures. To test its validity the algorithm was applied, in a numerical experiment, to fifty independent tropical radiosondes. The rms absolute deviation of the estimated moisture profiles from the actual profiles was comparable to that obtained using an iterative retrieval method reported earlier. The statistical method, however, requires several orders of magnitude less computer time than the iterative method; it is suitable for high speed processing of large amounts of data.

Kakar, R. K.↗

Integrating chemical kinetic rate equations by selective use of stiff and nonstiff methods

The effect of switching between nonstiff and stiff methods on the efficiency of algorithms for integrating chemical kinetic rate equations was examined. Different integration methods were tested by application of the packaged code LSODE to four practical combustion kinetics problems. The problems describe adiabatic, and homogeneous gas phase combustion reactions. It is shown that selective use of nonstiff and stiff methods in different regimes of a typical batch combustion problem is faster than the use of either method for the entire problem. The implications which result in the development of fast integration techniques for combustion kinetic rate equations are discussed.

Radhakrishnan, K.↗

Convergence of Newton's method for a single real equation

Newton's method for finding the zeroes of a single real function is investigated in some detail. Convergence is generally checked using the Contraction Mapping Theorem which yields sufficient but not necessary conditions for convergence of the general single point iteration method. The resulting convergence intervals are frequently considerably smaller than actual convergence zones. For a specific single point iteration method, such as Newton's method, better estimates of regions of convergence should be possible. A technique is described which, under certain conditions (frequently satisfied by well behaved functions) gives much larger zones where convergence is guaranteed.

Campbell, C. W.↗

A Comparison of the Bounded Derivative and the Normal Mode Initialization Methods Using Real Data

Browning et al. (1980) proposed an initialization method called the bounded derivative method (BDI). They used analytical data to test the new method. Kasahara (1982) theoretically demonstrated the equivalence between BDI and the well known nonlinear normal mode initialization method (NMI). The purposes of this study are the extension of the application of BDI to real data and comparison with NMI. The unbalanced initial state (UBD) is data of January, 1979 OOZ which were interpolated from the adjacent sigma levels of the GLAS GCM to the 300 mb surface. The global barotropic model described by Takacs and Balgovind (1983) is used. Orographic forcing is explicitly included in the model. Many comparisons are performed between various quantities. However, we only present a comparison of the time evolution at two grid points A(50 S, 90 E) and B(10 S, 20 E) which represent low and middle latitude locations. To facilitate a more complete comparison an initialization experiment based on the classical balance equation (CBE) was also included.

Semazzi, F. H. M.↗

Concurrent implementation of the Crank-Nicolson method for heat transfer analysis

To exploit the significant gains in computing speed provided by Multiple Instruction Multiple Data (MIMD) computers, concurrent methods for practical problems need to be investigated and test problems implemented on actual hardware. One such problem class is heat transfer analysis which is important in many aerospace applications. This paper compares the efficiency of two alternate implementations of heat transfer analysis on an experimental MIMD computer called the Finite Element Machine (FEM). The implicit Crank-Nicolson method is used to solve concurrently the heat transfer equations by both iterative and direct methods. Comparison of actual timing results achieved for the two methods and their significance relative to more complex problems are discussed.

Ransom, J. B.↗

Methods for roof-top mini-arrays

To test the idea of the Linsley effect mini array for the study of giant air showers, it is desirable to have a trigger that exploits the effect itself. In addition to the trigger, it is necessary to have a method for measuring the relative arrival times of the particle swarm selected by the trigger. Since the idea of mini arrays is likely to appeal to small research groups, it is desirable to try to design relatively simple and inexpensive methods, and methods that utilize existing detectors. Clusters of small detectors have been designed for operation in the local particle density realm where the probability of or = 2 particles per detector is small. Consequently, this method can discriminate pulses from each detector and thenceforth deal mainly with logic pulses.

Hazen, W. E.↗

Analysis of hourglass instabilities and control in underintegrated finite element methods

Belytschko et al. (1981, 1984) has developed stabilization methods for the treatment of underintegrated FEM problems; these methods involve the computation of an underintegrated stiffness matrix, which is rank-deficient, and the addition of a stabilization matrix which effectively eliminates the spurious modes. An attempt is presently made to give this a priori stabilization method a mathematical means of support. Attention is also given to an a posteriority stabilization method for hourglass control, in which an approximate solution of the underintegrated system is obtained and then subjected to a special projection in order to eliminate the hourglass modes. A proof is obtained for the convergence of this stabilized underintegrated approximation to the exact solution of a model problem at almost the same rate (as the mesh is refined) as the fully integrated solutions.

Jacquotte, O.-P.↗

Computation of internal flows: Methods and applications; Proceedings of the Energy Sources Technology Conference, New Orleans, LA, February 12-16, 1984

The present conference covers computational method applications, viscous-inviscid interaction techniques, viscous flow computational methods, and design-related methods. Attention is given to viscous flows in turbomachinery cascades, forbidden signals and apparent Mach numbers in supersonic cascades, the flow field in an engine particle separator, two-dimensional separated channel flows, turbulent separating flows over a rearward-facing step, the semielliptic analysis of two-dimensional internal and compressible viscous flows, spline solutions of the incompressible Navier-Stokes equations in a mildly nonorthogonal coordinate system, the design of highly loaded blades with blockage in cascade, and a finite analytic method for unsteady, three-dimensional Navier-Stokes equations.

Sockol, P. M.↗

Discrete-ordinates finite-element method for atmospheric radiative transfer and remote sensing

The principal features of the discrete-ordinates finite-element method are reviewed, and the applicability of general-purpose discrete-ordinates codes to atmospheric radiative transfer and remote sensing problems is demonstrated. In particular, numerical results for typical problems arising in meteorology, climatology, and remote sensing are shown to be in good agreement with results from other methods and measurements. A sample two-dimensional calculation demonstrates that specific capabilities available in the discrete-ordinates code TWOTRAN can produce new results that are valuable in the characterization of atmospheric effects on remote sensing (e.g., the adjacency effect). The intrinsic limitations of the method are also considered, and it is concluded that the strengths of the discrete-ordinates finite-element method outweigh its weaknesses.

Gerstl, S. A. W.↗

Integrating chemical kinetic rate equations by selective use of stiff and nonstiff methods

The effect of switching between nonstiff and stiff methods on the efficiency of algorithms for integrating chemical kinetic rate equations is presented. Different integration methods are tested by application of the packaged code LSODE to four practical combustion kinetics problems. The problems describe adiabatic, homogeneous gas-phase combustion reactions. It is shown that selective use of nonstiff and stiff methods in different regimes of a typical batch combustion problem is faster than the use of either method for the entire problem. The implications of this result to the development of fast integration techniques for combustion kinetic rate equations are discussed.

Radhakrishnan, K.↗