Search NASA⌕ Search

SEARCH · Search NASA

Results for “PLATES, FLAT - STRESSES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

A new technique for inducing a turbulent boundary layer in a supersonic flow

The feasibility of using slot injection to establish a turbulent boundary layer corresponding to a known Reynolds number is experimentally investigated. The basic concept consists of injecting secondary air through a slot. The air is injected at the same local static pressure and at a selected stagnation temperature to simulate a given upstream condition. The mass of the injected air can be controlled to match a desired Reynolds number. In the present experiment, secondary air was injected through a supersonic nozzle over a flat plate model. Heat transfer rates were measured at about 50 to 100 slot heights behind the slot, and the results were compared with theoretical estimates. Static pressure measurements were made over the surface in the streamwise direction. Velocity and Mach number profiles were obtained at a selected position downstream of the slot. Laminar and turbulent profiles were calculated from the Crocco method and the 1/7 power law respectively to compare with the results of measurements.

Miyazawa, M.↗

Analysis of a Pneumatic Probe for Measuring Exhaust-Gas Temperatures with Some Preliminary Experimental Results

A pneumatic probe based on continuity of mass flow through two restrictions separated by a cooling chamber was constructed to measure gas temperature at and beyond the limit of thermocouples. This probe consisted of a subsonic flat-plate orifice for the first restriction and a sonic-flow converging-diverging nozzle for the second restriction. The effect of variation in gas constants on the calibration is examined for common engine-exhaust gases. A high-temperature wind tunnel that allowed calibration of the probe at temperatures up to 2000 deg R and. Mach numbers up to 0.8 is described. Agreement to better than 30 deg R between pneumatic probe indication and the indication of a rake of radiation shielded thermocouples indicates that extrapolation of the calibration to higher temperatures is possible with fair accuracy

Scadron, Marvin D.↗

Sweep effect on the drag of rows of perpendicular circular cylinders in a laminar boundary layer at supersonic free-stream velocities

Drag measurements were obtained for circular cylinders attached perpendicularly to a flat-plate surface. Measurements were obtained for a single cylinder and for rows of cylinders. The cylinders were alined at various sweep angles relative to the free-stream velocity vector and at spacings appropriate for roughness elements used as boundary layer trips. The drag measurements were obtained for Mach numbers of 3.95 and 4.60, ratios of cylinder height to an undisturbed laminar boundary layer displacement thickness of approximately 1.0 to 3.0, a cylinder height-to-diameter ratio of approximately 2, and sweep angles up to 60. A complete presentation of the experimental results is given. A discussion of the more significant findings, including the most appropriate parameters for correlating the experimental results, is presented.

Lamb, M.↗

Weak incident shock interactions with Mach 8 laminar boundary layers

Weak shock-wave interactions with boundary layers on a flat plate were investigated experimentally in Mach 8 variable-density tunnel for plate-length Reynolds numbers. The undisturbed boundary layers were laminar over the entire plate length. Pressure and heat-transfer distributions were obtained for wedge-generated incident shock waves that resulted in pressure rises ranging from 1.36 to 4.46 (both nonseparated and separated boundary-layer flows). The resulting heat-transfer amplifications ranged from 1.45 to 14. The distributions followed established trends for nonseparated flows, for incipient separation, and for laminar free-interaction pressure rises. The experimental results corroborated established trends for the extent of the pressure rise and for certain peak heat-transfer correlations.

Kaufman, L. G., II↗

Effect of limb darkening on earth radiation incident on a spherical satellite

The thermal radiation from the earth incident on a spherical satellite depends on the angular distribution of earth-emitted radiation. An analysis is presented of this dependency, and calculated results are given, based on a published limb-darkening curve for the earth. The curve was determined from Tiros data, and is a statistical average over the entire globe between 75 deg latitude. The computed effect of limb darkening was 1.8 percent at 900 km altitude, 2.5 percent at 500 km altitude, and 3.0 percent at 300 km altitude. Below 300 km, it increased rapidly with decreasing altitude. Discussion is included of various other problems inherent in the use of orbiting spheres and stabilized flat plates to measure the heat radiated from the earth.

Katzoff, S.↗

Normal injection of helium from swept struts into ducted supersonic flow

Recent design studies have shown that airframe-integrated scramjets should include instream mounted, swept-back strut fuel injectors to obtain short combustors. Because there was no data in the literature on mixing characteristics of swept strut fuel injectors, the present investigation was undertaken to provide such data. This investigation was made with two swept struts in a closed duct at Mach number of 4.4 and nominal jet-to-air mass flow ratio of 0.029 with helium used to simulate hydrogen fuel. The data is compared with flat plate mounted normal injector data to obtain the effect of swept struts on mixing. Three injector patterns were evaluated representing the range of hole spacing and jet-to-freestream dynamic pressure ratio of interest. Measured helium concentration, pitot pressure, and static pressure in the downstream mixing region are used to generate contour plots necessary to define the mixing region flow field and the mixing parameters.

Mcclinton, C. R.↗

A new technique for inducing a turbulent boundary layer in a supersonic flow

The feasibility of using slot injection to establish a turbulent boundary layer corresponding to a known Reynolds number was investigated. The basic concept consists of injecting secondary air through a slot. The air is injected at the same local static pressure at a selected stagnation temperature to simulate a given up-stream heat conduction. The mass of the injected air is controlled to match a desired Reynolds number. Secondary air was injected through a supersonic nozzle over a flat plate model. Tests were conducted with different injection air conditions. Heat transfer rates were measured behind the slot and results were compared with theoretical estimates. Static pressure measurements were made over the surface in the streamwise direction. Velocity and Mach number profiles were determined downstream of the slot. Laminar and turbulent profiles were calculated to compare with the results of measurements. Experimental results indicate that this is an effective method for establishing a turbulent boundary layer having a prescribed value of R sub e Theta.

Miyazawa, M.↗

A computer program for two-dimensional and axisymmetric nonreacting perfect gas and equilibrium chemically reacting laminar, transitional and-or turbulent boundary layer flows

A computer program is described in detail for laminar, transitional, and/or turbulent boundary-layer flows of non-reacting (perfect gas) and reacting gas mixtures in chemical equilibrium. An implicit finite difference scheme was developed for both two dimensional and axisymmetric flows over bodies, and in rocket nozzles and hypervelocity wind tunnel nozzles. The program, program subroutines, variables, and input and output data are described. Also included is the output from a sample calculation of fully developed turbulent, perfect gas flow over a flat plate. Input data coding forms and a FORTRAN source listing of the program are included. A method is discussed for obtaining thermodynamic and transport property data which are required to perform boundary-layer calculations for reacting gases in chemical equilibrium.

Miner, E. W.↗

Gravitational clock: A proposed experiment for the measurement of the gravitational constant G

The increased importance and the fundamental significance of accurately measuring the gravitational constant G are discussed along with recent or proposed experimental measurements of G. The method of using mutually gravitating bodies in the clock mode in a drag-free satellite is described. A satellite experiment consisting of the flat-plate spherical mass oscillator proposed combines the mathematical and experimental conveniences most simply. It is estimated that accuracies of 1 part in 1,000,000 are easily obtainable by careful fabrication of parts. The use of cryogenic techniques, thin films, and superconductors allows increased accuracies of two or three orders of magnitude or better. These measurements can be increased to the level of 1 part in 10 to the 11th power at which time-variations, and other variations, in G can be observed.

Smalley, L. L.↗

The development of a solar residential heating and cooling system

The MSFC solar heating and cooling facility was assembled to demonstrate the engineering feasibility of utilizing solar energy for heating and cooling buildings, to provide an engineering evaluation of the total system and the key subsystems, and to investigate areas of possible improvement in design and efficiency. The basic solar heating and cooling system utilizes a flat plate solar energy collector, a large water tank for thermal energy storage, heat exchangers for space heating, and an absorption cycle air conditioner for space cooling. A complete description of all systems is given. Development activities for this test system included assembly, checkout, operation, modification, and data analysis, all of which are discussed. Selected data analyses for the first 15 weeks of testing are included, findings associated with energy storage and the energy storage system are outlined, and conclusions resulting from test findings are provided. An evaluation of the data for summer operation indicates that the current system is capable of supplying an average of 50 percent of the thermal energy required to drive the air conditioner. Preliminary evaluation of data collected for operation in the heating mode during the winter indicates that nearly 100 percent of the thermal energy required for heating can be supplied by the system.

Source record↗

A triangular thin shell finite element: Nonlinear analysis

Aspects of the formulation of a triangular thin shell finite element which pertain to geometrically nonlinear (small strain, finite displacement) behavior are described. The procedure for solution of the resulting nonlinear algebraic equations combines a one-step incremental (tangent stiffness) approach with one iteration in the Newton-Raphson mode. A method is presented which permits a rational estimation of step size in this procedure. Limit points are calculated by means of a superposition scheme coupled to the incremental side of the solution procedure while bifurcation points are calculated through a process of interpolation of the determinants of the tangent-stiffness matrix. Numerical results are obtained for a flat plate and two curved shell problems and are compared with alternative solutions.

Thomas, G. R.↗

Pressure gradient effects on heat transfer to reusable surface insulation tile-array gaps

An experimental investigation was performed to determine the effect of pressure gradient on the heat transfer within space shuttle reusable surface insulation (RSI) tile-array gaps under thick, turbulent boundary-layer conditions. Heat-transfer and pressure measurements were obtained on a curved array of full-scale simulated RSI tiles in a tunnel-wall boundary layer at a nominal free-stream Mach number and free-stream Reynolds numbers. Transverse pressure gradients of varying degree were induced over the model surface by rotating the curved array with respect to the flow. Definition of the tunnel-wall boundary-layer flow was obtained by measurement of boundary-layer pitot pressure profiles, wall pressure, and heat transfer. Flat-plate heat-transfer data were correlated and a method was derived for prediction of heat transfer to a smooth curved surface in the highly three-dimensional tunnel-wall boundary-layer flow. Pressure on the floor of the RSI tile-array gap followed the trends of the external surface pressure. Heat transfer to the surface immediately downstream of a transverse gap is higher than that for a smooth surface at the same location. Heating to the wall of a transverse gap, and immediately downstream of it, at its intersection with a longitudinal gap is significantly greater than that for the simple transverse gap.

Throckmorton, D. A.↗

Unsteady vortex lattice techniques applied to wake formation and performance of the statically thrusting propeller

The application is considered of vortex lattice techniques to the problem of describing the aerodynamics and performance of statically thrusting propellers. A numerical lifting surface theory to predict the aerodynamic forces and power is performed. The chordwise and spanwise loading is modelled by bound vortices fixed to a twisted flat plate surface. In order to eliminate any apriori assumptions regarding the wake shape, it is assumed the propeller starts from rest. The wake is generated in time and allowed to deform under its own self-induced velocity field as the motion of the propeller progresses. The bound circulation distribution is then determined with time by applying the flow tangency boundary condition at certain selected control points on the blades. The aerodynamics of the infinite wing and finite wing are also considered. The details of wake formation and roll-up are investigated, particularly the localized induction effect. It is concluded that proper wake roll-up and roll-up rates can be established by considering the details of motion at the instant of start.

Hall, G. F.↗

An improved source flow characteristic technique for the analysis of scramjet exhaust flow fields

The process is discussed of designing a nozzle for a hypersonic airbreathing vehicle which involves a complex study of the inter-relationship among many parameters: internal-external expansion, vehicle lift, drag, pitching moments, and structural and weight limitations. The source flow characteristic approach to the design process was extended and improved, and streamline interpolation procedure was incorporated. All characteristic and boundary calculations were made compatible with frozen, equilibrium and ideal gas thermodynamic options, while slip surface calculations (cowl interaction) were extended to underexpanded flow conditions. Since viscous forces can significantly influence vehicle forces, pitching moments and structural/weight considerations, a local integration via flat plate boundary layer skin friction and heat transfer coefficients was included. These effects are calculated using the Spalding and Chi method, and all force and moment calculations are performed via integration of the local forces acting on the specified vehicle wetted areas.

Delguidice, P. D.↗

On upstream blocking in a viscous diffusive stratified flow

The effect of diffusion of specie upon the flow about a transverse flat plate moving horizontally in a viscous stratified medium is considered. Asymptotic expansions are used to define a parameter regime where a viscous-diffusive-buoyancy balance is dominant. The solution, expressed in terms of an inverse Fourier transform, is numerically integrated. The results show that, as in the non-diffusive problem, a region of closed streamlines exists ahead of the body. However, unlike the case where diffusion is neglected, the density field within this recirculating region is uniquely determined and found to be statically stable. It is also found that varying the relative amount of diffusion affects not only the density distribution, but the velocity profile as well, indicating a strong coupling between the vorticity and specie equation.

Koop, C. G.↗

Wind tunnel investigation of a Centaur standard shroud compartment vent from Mach number of 0.70 to 1.96

An experimental investigation was conducted in the Lewis Research Center 8- by 6-foot supersonic wind tunnel to determine the vent discharge coefficient for the Centaur standard shroud/liquid hydrogen tank compartment vent. The test was conducted from Mach 0.70 to 1.96 with the vent mounted in a flat plate. Full scale simulated flight hardware, such as the vent, corrugations, aft field joint ring and ice bag clip was used. Air was discharged from a plenum chamber, located on the tunnel sidewall behind the plate, through five 6.35 cm diameter vent orifices into the free stream. Boundary layer thickeners, analytically predicted displacement thickness for the vehicle nominal flight trajectory could be simulated over the Mach number range. The highest vent discharge coefficient for any given Mach number and vent pressure ratio generally occurred at the maximum displacement thickness.

Johns, A. L.↗

Boundary-layer development and transition due to free-stream exothermic reactions in shock-induced flows

A study of the effect of free-stream thermal-energy release from shock-induced exothermic reactions on boundary-layer development and transition is presented. The flow model is that of a boundary layer developing behind a moving shock wave in two-dimensional unsteady flow over a shock-tube wall. Matched sets of combustible hydrogen-oxygen-nitrogen mixtures and inert hydrogen-nitrogen mixtures were used to obtain transition data over a range of transition Reynolds numbers from 1,100,000 to 21,300,000. The heat-energy is shown to significantly stabilize the boundary layer without changing its development character. A method for application of this data to flat-plate steady flows is included.

Hall, J. L.↗

Vorticity associated with a jet in a cross flow

An extensive wind-tunnel test of a round turbulent jet directed normally through a flat plate into a subsonic cross flow has been conducted. The results of the velocity field measurements are presented in a concise and usable form through the use of simple models to relate the velocity field to empirical values for the strength and location of the pair of contrarotating vortices associated with the jet.

Fearn, R.↗