Search NASA⌕ Search

SEARCH · Search NASA

Results for “Recovery Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Design techniques for modular integrated utility systems

Features basic to the integrated utility system, such as solid waste incineration, heat recovery and usage, and water recycling/treatment, are compared in terms of cost, fuel conservation, and efficiency to conventional utility systems in the same mean-climatic area of Washington, D. C. The larger of the two apartment complexes selected for the test showed the more favorable results in the three areas of comparison. Restrictions concerning the sole use of currently available technology are hypothetically removed to consider the introduction and possible advantages of certain advanced techniques in an integrated utility system; recommendations are made and costs are estimated for each type of system.

Wolfer, B. M.↗
NASA NTRS1976

The development and flight test of an electronic integrated propulsion control system

Advanced technical features of the electronic integrated propulsion control system (IPCS) and flight evaluation tests of IPCS (F-111E with TF30-P-9 engines as test vehicle) are described. Nine baseline flight tests and 15 IPCS flight tests were conducted. Instrumentation, data acquisition and data processing systems, software maintenance procedures, flight test procedures, flight safety criteria, flight test results, and ground and flight testing of the aircraft system are described. Advantages conferred by IPCS include: faster accelerations (both gas generator and afterburner performance), better thrust and flight control, reduced flight idle thrust, reduced engine ground trim, extended service ceiling, automatic stall detection, and stall recovery detection.

Johnson, H. J.↗
NASA NTRS1986

Theory and Tests of Two-Phase Turbines

New turbines open possibility of new types of power cycles. Report describes theoretical analysis and experimental testing of two-phase impulse turbines. Such turbines open possibility of new types of power cycles operating with extremely wet mixtures of steam and water, organic fluids, or immiscible liquids and gases. Possible applications are geothermal power, waste-heat recovery, refrigerant expansion, solar conversion, transportation, and engine-bottoming cycles.

Elliott, D. G.↗
NASA NTRS1990

Multiversion software reliability through fault-avoidance and fault-tolerance

In this project we have proposed to investigate a number of experimental and theoretical issues associated with the practical use of multi-version software in providing dependable software through fault-avoidance and fault-elimination, as well as run-time tolerance of software faults. In the period reported here we have working on the following: We have continued collection of data on the relationships between software faults and reliability, and the coverage provided by the testing process as measured by different metrics (including data flow metrics). We continued work on software reliability estimation methods based on non-random sampling, and the relationship between software reliability and code coverage provided through testing. We have continued studying back-to-back testing as an efficient mechanism for removal of uncorrelated faults, and common-cause faults of variable span. We have also been studying back-to-back testing as a tool for improvement of the software change process, including regression testing. We continued investigating existing, and worked on formulation of new fault-tolerance models. In particular, we have partly finished evaluation of Consensus Voting in the presence of correlated failures, and are in the process of finishing evaluation of Consensus Recovery Block (CRB) under failure correlation. We find both approaches far superior to commonly employed fixed agreement number voting (usually majority voting). We have also finished a cost analysis of the CRB approach.

Vouk, Mladen A.↗
NASA NTRS1999

Dose-response relationship between sleep duration and human psychomotor vigilance and subjective alertness

Although it has been well documented that sleep is required for human performance and alertness to recover from low levels after prolonged periods of wakefulness, it remains unclear whether they increase in a linear or asymptotic manner during sleep. It has been postulated that there is a relation between the rate of improvement in neurobehavioral functioning and rate of decline of slow-wave sleep and/or slow-wave activity (SWS/SWA) during sleep, but this has not been verified. Thus, a cross-study comparison was conducted in which dose-response curves (DRCs) were constructed for Stanford Sleepiness Scale (SSS) and Psychomotor Vigilance Task (PVT) tests taken at 1000 hours by subjects who had been allowed to sleep 0 hours, 2 hours, 5 hours or 8 hours the previous night. We found that the DRCs to each PVT metric improved in a saturating exponential manner, with recovery rates that were similar [time constant (T) approximately 2.14 hours] for all the metrics. This recovery rate was slightly faster than, though not statistically significantly different from, the reported rate of SWS/SWA decline (T approximately 2.7 hours). The DRC to the SSS improved much more slowly than psychomotor vigilance, so that it could be fit equally well by a linear function (slope = -0.26) or a saturating exponential function (T = 9.09 hours). We conclude that although SWS/SWA, subjective alertness, and a wide variety of psychomotor vigilance metrics may all change asymptotically during sleep, it remains to be determined whether the underlying physiologic processes governing their expression are different.

Non-NASA Center↗
NASA NTRS1994

Effects of spaceflight on ocular counterrolling and the spatial orientation of the vestibular system

We recorded the horizontal (yaw), vertical (pitch), and torsional (roll) eye movements of two rhesus monkeys with scleral search coils before and after the COSMOS Biosatellite 2229 Flight. The aim was to determine effects of adaptation to microgravity on the vestibulo-ocular reflex (VOR). The animals flew for 11 days. The first postflight tests were 22 h and 55 h after landing, and testing extended for 11 days after reentry. There were four significant effects of spaceflight on functions related to spatial orientation: (1) Compensatory ocular counterrolling (OCR) was reduced by about 70% for static and dynamic head tilts with regard to gravity. The reduction in OCR persisted in the two animals throughout postflight testing. (2) The gain of the torsional component of the angular VOR (roll VOR) was decreased by 15% and 50% in the two animals over the same period. (3) An up-down asymmetry of nystagmus, present in the two monkeys before flight was reduced after exposure to microgravity. (4) The spatial orientation of velocity storage was shifted in the one monkey that could be tested soon after flight. Before flight, the yaw axis eigenvector of optokinetic afternystagmus was close to gravity when the animal was upright or tilted. After flight, the yaw orientation vector was shifted toward the body yaw axis. By 7 days after recovery, it had reverted to a gravitational orientation. We postulate that spaceflight causes changes in the vestibular system which reflect adaptation of spatial orientation from a gravitational to a body frame of reference. These changes are likely to play a role in the postural, locomotor, and gaze instability demonstrated on reentry after spaceflight.

Non-NASA Center↗
NASA NTRS1948

Preliminary Results of British Nene II Engine Altitude-Chamber Performance Investigation. I - Altitude Performance Using Standard 18.75-Inch-Diameter Jet Nozzle: Altitude Performance Using Standard 18.75-Inch-Diameter Jet Nozzle - 1

An investigation is being conducted to determine the altitude performance characteristics of the British Nene II engine and its components. The present paper presents the preliminary results obtained using a standard jet nozzle. The test results presented are for conditions simulating altitudes from sea level to 60,000 feet and ram pressure ratios from 1.0 to 2.3. These ram pressure ratios correspond to flight Mach numbers between zero and 1.16 assuming a 100 percent ram recovery.

Barson, Zelmar↗
NASA NTRS2017

High Lift Common Research Model for Wind Tunnel Testing: An Active Flow Control Perspective

This paper provides an overview of a research and development effort sponsored by the NASA Advanced Air Transport Technology Project to achieve the required high-lift performance using active flow control (AFC) on simple hinged flaps while reducing the cruise drag associated with the external mechanisms on slotted flaps of a generic modern transport aircraft. The removal of the external fairings for the Fowler flap mechanism could help to reduce drag by 3.3 counts. The main challenge is to develop an AFC system that can provide the necessary lift recovery on a simple hinged flap high-lift system while using the limited pneumatic power available on the aircraft. Innovative low-power AFC concepts will be investigated in the flap shoulder region. The AFC concepts being explored include steady blowing and unsteady blowing operating in the spatial and/or temporal domain. Both conventional and AFC-enabled high-lift configurations were designed for the current effort. The high-lift configurations share the cruise geometry that is based on the NASA Common Research Model, and therefore, are also open geometries. A 10%-scale High Lift Common Research Model (HL-CRM) is being designed for testing at the NASA Langley Research Center 14- by 22-Foot Subsonic Tunnel during fiscal year 2018. The overall project plan, status, HL-CRM configurations, and AFC objectives for the wind tunnel test are described.

Lin, John C.↗
NASA NTRSDate not supplied

Water Collection, Recovery, and Bag Containment Analysis of Trash Models of the Trash Compaction and Processing System (TCPS)

The Trash Compaction and Processing System (TCPS) aims to reduce volume, biologically safen, physically stabilize, manage effluents, and recover resources from astronaut trash in the International Space Station (ISS). The Heat Melt Compactor (HMC) at NASA Ames Research Center (ARC) serves as a test system that supports TCPS development by conducting risk reduction activities associated with an ISS flight demonstration. One of the resources desired to be recovered is water from the trash. The HMC Gen 3 has undergone several tests of different trash models and cases in which a containment bag is used or not. This paper will analyze the water collected and recovered from these tests and analyze the effect of specific trash containment bags.

Janine Criselda Young↗
NASA NTRSDate not supplied

Wind-US Simulations of the NASA 1507 Inlet Test Case

Steady-state, Reynolds-Averaged Navier-Stokes (RANS) computational fluid dynamics (CFD) simulations were performed of the NASA 1507 Inlet Test Case from the 6th AIAA Propulsion Aerodynamics Workshop (PAW) held in January 2023 using the Wind-US CFD solver. The simulations were performed with bleed regions modeled as surface patches and the Slater bleed boundary condition models were applied within those regions. Both the constant-plenum-pressure and the fixed-plenum-exit bleed models where applied. The vortex generators were modeled using the Bender-Anderson-Yagle (BAY) vortex generator model. The CFD simulations were performed for inlet engine-face flow ratios varying from supercritical to subcritical inlet operation until inlet unstart. The results of the CFD simulations were compared to wind-tunnel data which included boundary layer profiles, axial static pressure distributions, bleed rates, total pressure recovery performance curves, and engine-face total pressure rake profiles. The CFD simulations were able to match most of the boundary layer rake data near the geometric throat, but the boundary layers on the centerbody were thinner than indicated by the wind-tunnel data. For the supercritical CFD simulations, the engine-face flow ratio was at least 2% to 2.5% lower than indicated by the wind-tunnel data, but still consistent with the level of supercritical bleed. The engine-face flow rates of the wind-tunnel tests had an uncertainty of ±2% which could explain the differences. The supercritical engine-face flow rates of the wind-tunnel data indicated a 5% supercritical bleed rate rather than the reported 7.18% bleed rate. The CFD simulations were able to calculate the maximum total pressure recovery of pt2/pt = 0.907 as observed for the wind-tunnel data. The CFD simulations with the constant-pressure bleed model were able to obtain a much lower engine-face total pressure ratio than indicated by both the wind-tunnel data and the CFD simulations using a fixed-plenum-exit bleed model. The CFD simulations indicated a sharp static pressure rise for the terminal shock rather than a more gradual rise indicated by the wind-tunnel data. The CFD simulations were not able to accurately compute the total pressure variation across the engine-face total pressure rake.

Supersonics↗
NASA NTRS1975

Quiet, clean short-haul experimental engine (QCSEE) test results from a 14 cm inlet for a variable pitch fan thrust reverser

A 1/13th scale model of the fan discharge duct was tested with a matrix of flare exlets. Exlets are flared fan nozzles configured for improved reverse flow inlet performance for reverse pitch fan applications. Results showed that a flare type exlet is an acceptable design for QCSEE, as indicated by high pressure recovery and low distortion performance.

Vier, W. F.↗
NASA NTRS1977

Static, noise, and transition tests of a combined-surface-blowing V/STOL lift/propulsion system

Efficient thrust vectoring and high levels of circulatory lift were obtained in tests of a half model V/STOL airplane by using a type of externally blown jet flap in which the jet exhaust from wing-mounted cruise fans is directed over both upper and lower surfaces of a flapped wing. Approximately 90% thrust recovery with 87 deg of thrust vectoring was achieved under static conditions using 89 deg of trailing edge flap deflection. The approximately 10% loss appears to be associated primarily with pressure losses due to the flap brackets or slot entries. The jet induced lift was shown to be 55% of the theoretical value for a fullspan jet-flapped wing, even though only 27.5% of the wingspan was immersed in the jet. Steady rate of descent capability in excess of 1,000 feet per minute is predicted. The possibility of significant aerodynamic-noise cancelling when blowing over both surfaces at high velocities is indicated.

Schoen, A. H.↗
NASA NTRS1985

Improved Exhaust Diffuser for Jet-Engine Testing

High-altitude simulator reduced power requirements. Test cell uses its exhaust-capture duct only to remove gases from engine; cooling air evacuated through separate path by auxiliary suction system. This way, capture duct cross-sectional area kept close to exhaust jet area, leading to greatly improved recovery performance.

Parikh, P. G.↗
NASA NTRS1993

Space station static and dynamic analyses using parallel methods

Algorithms for high-performance parallel computers are applied to perform static analyses of large-scale Space Station finite-element models (FEMs). Several parallel-vector algorithms under development at NASA Langley are assessed. Sparse matrix solvers were found to be more efficient than banded symmetric or iterative solvers for the static analysis of large-scale applications. In addition, new sparse and 'out-of-core' solvers were found superior to substructure (superelement) techniques which require significant additional cost and time to perform static condensation during global FEM matrix generation as well as the subsequent recovery and expansion. A method to extend the fast parallel static solution techniques to reduce the computation time for dynamic analysis is also described. The resulting static and dynamic algorithms offer design economy for preliminary multidisciplinary design optimization and FEM validation against test modes. The algorithms are being optimized for parallel computers to solve one-million degrees-of-freedom (DOF) FEMs. The high-performance computers at NASA afforded effective software development, testing, efficient and accurate solution with timely system response and graphical interpretation of results rarely found in industry. Based on the author's experience, similar cooperation between industry and government should be encouraged for similar large-scale projects in the future.

Gupta, V.↗
NASA NTRS2014

Preliminary Analysis of Aircraft Loss of Control Accidents: Worst Case Precursor Combinations and Temporal Sequencing

Aircraft loss of control (LOC) is a leading cause of fatal accidents across all transport airplane and operational classes, and can result from a wide spectrum of hazards, often occurring in combination. Technologies developed for LOC prevention and recovery must therefore be effective under a wide variety of conditions and uncertainties, including multiple hazards, and their validation must provide a means of assessing system effectiveness and coverage of these hazards. This requires the definition of a comprehensive set of LOC test scenarios based on accident and incident data as well as future risks. This paper defines a comprehensive set of accidents and incidents over a recent 15 year period, and presents preliminary analysis results to identify worst-case combinations of causal and contributing factors (i.e., accident precursors) and how they sequence in time. Such analyses can provide insight in developing effective solutions for LOC, and form the basis for developing test scenarios that can be used in evaluating them. Preliminary findings based on the results of this paper indicate that system failures or malfunctions, crew actions or inactions, vehicle impairment conditions, and vehicle upsets contributed the most to accidents and fatalities, followed by inclement weather or atmospheric disturbances and poor visibility. Follow-on research will include finalizing the analysis through a team consensus process, defining future risks, and developing a comprehensive set of test scenarios with correlation to the accidents, incidents, and future risks. Since enhanced engineering simulations are required for batch and piloted evaluations under realistic LOC precursor conditions, these test scenarios can also serve as a high-level requirement for defining the engineering simulation enhancements needed for generating them.

Belcastro, Christine M.↗
NASA NTRS2014

Fiber Attachment Module Experiment (FAME): Using a Multiplexed Miniature Hollow Fiber Membrane Bioreactor Solution for Rapid Process Testing

Bioreactor research is mostly limited to continuous stirred-tank reactors (CSTRs) which are not an option for microgravity (g) applications due to the lack of a gravity gradient to drive aeration as described by the Archimedes principle. Bioreactors and filtration systems for treating wastewater in g could avoid the need for harsh pretreatment chemicals and improve overall water recovery. Solution: Membrane Aerated Bioreactors (MABRs) for g applications, including possible use for wastewater treatment systems for the International Space Station (ISS).

Module Experiment↗
NASA NTRS2016

Design Status of the Capillary Brine Residual in Containment Water Recovery System

One of the goals of the AES Life Support System (LSS) Project is to achieve 98% water loop closure for long duration human exploration missions beyond low Earth orbit. To meet this objective, the AES LSS Project is developing technologies to recover water from wastewater brine; highly concentrated waste products generated from a primary water recovery system. The state of the art system used aboard the International Space Station (ISS) has the potential to recover up to 85% water from unine wastewater, leaving a significant amounts of water in the waste brine, the recovery of which is critical technology gap that must be filled in order to enable long duration human exploration. Recovering water from the urine wastewater brine is complicated by the concentration of solids as water is removed from the brine, and the concentration of the corrosive, toxic chemicals used to stabilize the urine which fouls and degrades water processing hardware, and poses a hazard to operators and crew. Brine Residual in Containment (BRIC) is focused on solids management through a process of "in-place" drying - the drying of brines within the container used for final disposal. Application of in-place drying has the potential to improve the safety and reliability of the system by reducing the exposure to curew and hardware to the problematic brine residual. Through a collaboration between the NASA Johnson Space Center and Portland Status University, a novel water recovery system was developed that utilizes containment geometry to support passive capillary flow and static phase separation allowing free surface evaporation to take place in a microgravity environment. A notional design for an ISS demonstration system was developed. This paper describes the testing performed to characterize the performance of the system as well as the status of the system level design.

Sargusingh, Miriam J.↗
NASA NTRSDate not supplied

Suborbital Testing of the OSCAR Trash-to-Gas System

With the sustained human exploration of nearby celestial bodies on the horizon, a renewed outlook on crew waste management must be realized. Current waste management strategies aboard the International Space Station become impractical as we venture beyond low Earth orbit. Furthermore, for future exploration missions, extracting resources from various waste streams becomes increasingly advantageous. One method of combatting the long-duration waste management problem is by thermally degrading solid and liquid crew waste items into a chemically inert, ventable gas stream, a process known as Trash-to-Gas. The Orbital Syngas/Commodity Augmentation Reactor (OSCAR) is the state-of-the-art Trash-to-Gas system which has been designed to explore microgravity Trash-to-Gas concepts for improved mass/volume reduction and resource recovery from waste. OSCAR is a subscale testbed design that supports the NASA Logistics Reduction project under the Advanced Exploration Systems Program and Space Technology Mission Directorate Flight Opportunities Program to determine the feasibility of Trash-to-Gas technology for future use on long duration space missions. OSCAR has flown on two suborbital flight demonstrations aboard Blue Origin’s New Shepard launch vehicle. This paper presents a high-level comparative analysis of these microgravity test campaigns with Earth gravity laboratory experiments. Solid-to-gas conversion, gas production & composition, and reactor temperature & pressure are compared to highlight the operational factors and performance differences within the microgravity environment for future optimization.

Ray P Pitts↗