Search NASA⌕ Search

SEARCH · Search NASA

Results for “dynamic load testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

Predicted Heat Flux Performance of Actively Cooled Tungsten-Armored Graphitic Foam Monoblocks

Tungsten (W)–armored graphitic foam monoblocks were developed for applications requiring high-Z plasma-facing material in long-pulse fusion experiments and ultimately deuterium-tritium fusion reactors. The monoblocks are an integrated material system combining the advantages of a chemical vapor deposited (CVD) W coating with a high-conductivity graphitic foam. The W is a high-melting-point, high-Z material with low tritium retention. The graphitic foam coupled to a swirl tube serves as a high-thermal-conductivity heat sink that cannot melt, although it can sublime at much higher temperatures than copper melts. Together, they comprise a robust plasma-facing component (PFC) weighing roughly 5% of an all-W component or 17% of a traditional W-coated copper heat sink.A single-channel mock-up consisting of four graphitic foam monoblocks equipped with a water-cooled swirl tube was fabricated for eventual testing in the 60-kW, EB-60, rastered electron beam at the Applied Research Laboratory of The Pennsylvania State University. Two monoblocks have a thin 50-μm-thick coating of pure W chemically vapor deposited over NbC and pure Nb interlayers. Two others have a 2-mm-thick pure W coating CVD on graphitic monoblocks using the same interlayers. The mock-up will be cooled with available 10 m/s, 0.7 MPa water with a 22°C inlet temperature and subjected to varying uniform heat loads up to 20 MW/m 2 . It is equipped with type-K thermocouples at various depths, and calibrated infrared thermography and spot pyrometry will be used to characterize the heated surface. Real-time water calorimetry will be used to ascertain the absorbed steady-state power and infer the heat flux during testing. Since testing cannot be done under prototypic divertor flow conditions, it is necessary to predict the thermal response of this novel PFC system and investigate the power sharing between radiation and convection at divertor heat flux levels and its inherent ability to avoid critical heat flux. Results are reported for predictions obtained from computational fluid dynamics models up to 30 MW/m 2 of steady-state uniform heat flux. Leading-edge heat loads of 30 MW/m 2 on a 2-mm-wide side strip were also investigated to ascertain if coating delamination is likely.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mechanical properties of water desalination and wastewater treatment membranes

Applications of membrane technology in water desalination and wastewater treatment have increased significantly in the past fewdecades due to itsmany advantages over otherwater treatment technologies.Water treatment membranes provide high flux and contaminant rejection ability and require good mechanical strength and durability. Thus, assessing the mechanical properties of water treatment membranes is critical not only to their design, but also for studying their failure mechanisms, including the surface damage, mechanical and chemical ageing, delamination and loss of dimensional stability of the membranes. The various experimental techniques to assess themechanical properties ofwastewater treatment and desalinationmembranes are reviewed. Uniaxial tensile test, bending test, dynamic mechanical analysis, nanoindentation and bursting tests are the most widely used mechanical characterization methods for water treatment membranes. Mechanical degradations induced by fouling, chemical cleaning as well as membrane delamination are then discussed. Moreover, in order to study the membranesmechanical responses under similar loading conditions, the stress-state of the membranes are analyzed and advanced mechanical testing approaches are proposed. Lastly, some perspectives are highlighted to study the structure-properties relationship for wastewater treatment and water desalination membranes.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Meeting Residential Ventilation Standards Through Dynamic Control of Ventilation Systems

Existing ventilation standards, including American Society of Heating, Refrigerating, and Air-conditioning Engineers (ASHRAE) Standard 62.2, specify continuous operation of a defined mechanical ventilation system to provide minimum ventilation, with time-based intermittent operation as an option. This requirement ignores several factors and concerns including: other equipment such as household exhaust fans that might incidentally provide ventilation, negative impacts of ventilation when outdoor pollutant levels are high, the importance of minimizing energy use particularly during times of peak electricity demand, and how the energy used to condition air as part of ventilation system operation changes with outdoor conditions. Dynamic control of ventilation systems can provide ventilation equivalent to or better than what is required by standards while minimizing energy costs and can also add value by shifting load during peak times and reducing intake of outdoor air contaminants. This article describes the logic that enables dynamic control of whole-house ventilation systems to meet the intent of ventilation standards and demonstrates the dynamic ventilation system control concept through simulations and field tests of the Residential Integrated Ventilation-Energy Controller (RIVEC).

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Performance Evaluation of a Microgrid System with Grid-Forming and Grid-Following Inverters with Diesel Generators: Insights From Hardware Experiments

This paper presents a comprehensive performance evaluation of a microgrid system integrating grid-forming (GFM) inverters, grid-following (GFL) inverters, and a diesel generator, focusing on their interactions and behavior under various dynamic events. The study is conducted using a pure hardware setup comprising two GFM inverters, one GFL inverter, a diesel generator, load banks, a point of common coupling (PCC), and an emulated main grid. The evaluation specifically examines dynamic scenarios, including voltage jumps, phase jumps, rate of change of frequency (ROCOF), synchronization, and islanding operations, which pose critical challenges to system stability. Among all the tests conducted, the overloading and phase jump tests proved to be the most challenging. The capacity of the DC side is crucial for withstanding overloading and grid disturbance tests; otherwise, GFM inverters frequently trip due to DC undervoltage. Throughout all grid disturbance tests, the diesel generator consistently stands out as the most robust and reliable GFM unit in the system. Overall, insights from these hardware experiments shed light on the response characteristics of different generation types during grid disturbances and identify potential stability concerns in such hybrid microgrid systems.

14 SOLAR ENERGY↗

A Variable Pressure Multi-Pressure Rail System Design for Agricultural Applications

This paper presents a solution for reducing energy loss in the hydraulic control system of agricultural tractors and their implements. The solution is referred to as a multi-pressure rail (MPR) and provides power to the hydraulic functions following a pressure control logic, as opposed to the traditional flow control logic typical of hydraulic systems used in off-road vehicles. The proposed hydraulic control system allows for elimination of redundant flow control valves in the state-of-the-art system, which cause excessive throttling losses leading to poor overall energy efficiency. Related work on MPR technology targets construction vehicles, where the MPR solution can allow energy recovery during overrunning loads and better engine management. This paper alternatively addresses the case of agricultural applications where functions mostly operate under resistive load conditions with slow dynamics, which offers an opportunity to target throttle losses. For this purpose, the paper introduces a variable pressure control strategy to handle the instantaneous pressure at each rail. To develop both the controller and the hydraulic system architecture, a stationary test rig is conceived and used to validate a numerical simulation model of the MPR system and its control strategy. Particular focus is given to the dynamic behavior of the system during the switches of a function between different pressure rails, which needs to ensure reduced oscillations of the flow provided to each hydraulic function. Once validated, the simulation model is used to predict the energy savings of the MPR solution in an actual application: a 435 hp hydraulic tractor powering a 16-row planter, for which operating features during typical drive cycles were available to the authors. The results show up to 59% total power reduction at the pump shaft, corresponding to 89.8% system efficiency gain.

36 MATERIALS SCIENCE↗

Parallel processing for nonlinear dynamics simulations of structures including rotating bladed-disk assemblies

The principal objective of this research is to develop, test, and implement coarse-grained, parallel-processing strategies for nonlinear dynamic simulations of practical structural problems. There are contributions to four main areas: finite element modeling and analysis of rotational dynamics, numerical algorithms for parallel nonlinear solutions, automatic partitioning techniques to effect load-balancing among processors, and an integrated parallel analysis system.

Hsieh, Shang-Hsien↗

Dynamic Leg Exercise Improves Tolerance to Lower Body Negative Pressure

These results clearly demonstrate that dynamic leg exercise against the footward force produced by LBNP substantially improves tolerance to LBNP, and that even cyclic ankle flexion without load bearing also increases tolerance. This exercise-induced increase of tolerance was actually an underestimate, because subjects who completed the tolerance test while exercising could have continued for longer periods. Exercise probably increases LBNP tolerance by multiple mechanisms. Tolerance was increased in part by skeletal muscle pumping venous blood from the legs. Rosenhamer and Linnarsson and Rosenhamer also deduced this for subjects cycling during centrifugation, although no measurements of leg volume were made in those studies: they found that male subjects cycling at 98 W could endure 3 Gz centrifugation longer than when they remained relaxed during centrifugation. Skeletal muscle pumping helps maintain cardiac filling pressure by opposing gravity-, centrifugation-, or LBNP-induced accumulation of blood and extravascular fluid in the legs.

Watenpaugh, D. E.↗

Enhancements, Verification, and VMS Integration of VTOL Concept Vehicle Simulation Models

Advanced Rotorcraft Technology (ART) and the NASA Ames Aeromechanics branch have jointly developed FLIGHTLAB simulation models for Advanced Air Mobility (AAM) VTOL concept vehicles. The overarching purpose of the simulation model development is to establish a set of well defined reference vehicles for FLIGHTLAB users and the rotorcraft community. The ongoing research effort and enhancement of these AAM simulation models to fulfill the role of quality reference vehicles is this paper’s focus. The content of this paper expands on the established characteristics of these AAM models in three primary areas. First, enhancement of the lift+cruise and tiltwing models with elastic airframe properties is discussed. The process of setting up the elastic airframe model in FLIGHTLAB, as well as the impacts on flight characteristics are explained. The introduction of the elastic airframe modeling allows these models to be used in flight dynamics, loads, and vibration analysis of the configuration designs. Next, linear model generation from the enhanced simulation model is covered. Confirming the validity of the linearized models is of importance, as these linear models are utilized for flight control design and tuning for these experimental configurations. For the final focus, the progress towards implementation of these models into the NASA Ames Vertical Motion Simulator (VMS) is described. This task seeks to demonstrate the procedures of integrating a FLIGHTLAB flight simulation in the VMS environment, test fully integrated simulation with communication between flight dynamics, control, and propulsion models, and explore the essential aspects of simulation model integration in a full flight simulator environment. This includes I/O definition, initialization, trim, flying, etc. By expanding the capabilities of the AAM simulation models, they continue to develop as valuable and approachable modeling references.

VMS↗

Estimation of Lower-Body Kinetics from Loading Profile and Kinematics Alone, Without Measured Ground Reaction Forces

Biomechanical models of human motion can estimate kinetic outcomes, such as joint moments, joint forces and muscle forces. Typically, one performs an inverse dynamics (ID) analysis to compute joint moments from joint angles and measured external forces. Sometimes it is impractical to measure ground reaction forces and moments (GRF&M). We devised an empirical method for performing ID analysis of resistance exercises without measured GRF&M. The method solves the multibody dynamics equations of motion with four key assumptions about the GRF&M that reduce the number of unknowns. The assumptions are 1) negligible ground reaction moments, 2) fixed lateral/medial location of the center of pressure (COP), 3) equal fore/aft location of the COP between the feet, and 4) constant angle of the GRF vector relative to the vertical axis in the frontal plane. We used evaluation trials from a spaceflight countermeasure resistance training device to test this approach. Four participants performed squat and deadlift exercises at various loads. We compared results from traditional ID analysis to results without measured GRF&M using our method. We found that joint moment trajectories in the sagittal plane were qualitatively similar in shape between the two methods, and the amount of root mean squared error (RMSE), measured by difference in joint moment impulse, was typically under 10 percent. Non-sagittal joint moment trajectories, which are much lower in overall magnitude, were not qualitatively similar in shape between the two methods. Non-sagittal moments displayed much higher RMSE, with typical values well over 50 percent. These findings were further supported by validation metrics (Sprague and Geers' P and M metrics, Pearson's r correlation coefficient). Based on these findings, we concluded that useful kinetic results are obtained from ID analysis of squat and deadlift exercises, even when GRF&M are not measured, as long as the outcomes of interest lie in the sagittal plane.

computational modeling↗

Persistent Elevated Soot Emissions Induced by Clustered Stochastic Preignition Events

Stochastic Preignition (SPI) is an abnormal combustion phenomenon that can occur in spark-ignition engines particularly under high-load operation. SPI is characterized by uncontrolled initiation of combustion prior to spark discharge, an abnormal combustion process that can lead to severe knock events and significant engine damage. SPI has been associated with fuel properties, lubricant composition, and engine design and operation. Here, in this work, a single-cylinder test engine with a dry-sump oil system was utilized to study the SPI response of E10 and E25 fuels with a range of Reid Vapor Pressure (RVP). An automated test procedure was employed, consisting of ten square-waved load profile segments, with each segment composed of 5 min of low-load operation followed by 25 min of sustained high-load operation. These tests were replicated across multiple days of testing including a lubricant triple flush between tests, and an online Fuel in Oil diagnostic measurement. Exhaust particulate emissions were continuously measured by an AVL microsoot sensor (MSS). Elevated particulate matter emissions were observed to occur concurrently with SPI events as blooms of soot. Particularly after clustered events (i.e., multiple SPI cycles occurring within 10 consecutive engine cycles), high soot emissions were observed to persist over several days of sequential operation despite daily lubricant changes, a complete warm-up procedure, and sustained low-load operation between test segments. This result implies that the particulate emissions trends may be dominated by deposit-based effects, where higher load operation is needed to alter deposition and formation processes. The observed soot blooms were also found to correspond to a reduction in the engine fueling and the fuel engine oil dilution rate despite the engine exhaust remaining at stoichiometric exhaust operation. These observations suggest that post-SPI events, pathways for lubricant migration and consumption into the combustion chamber may occur until these pathways are closed from deposit formation or ring dynamics during extended operation. These observed sooting propensity persisted with all fuels tests, but a linear correlation was observed between the summation of soot and particulate matter index (PMI) value for each fuel as well as SPI events, proving that PMI is a crucial fuel property for reducing SPI.

Splitter, Derek [Oak Ridge National Laboratory (OR↗

X-57 “Maxwell” High-Lift Propeller Testing and Model Development

NASA’s X-57 “Maxwell” distributed electric propulsion flight demonstrator has a high-lift system that includes 12 fixed-pitch high-lift propellers located upstream of the wing leading edge for lift augmentation at low speeds. These high-lift propellers are not required at higher speeds and are folded conformally along the nacelles to reduce drag when not in operation. Aircraft performance models and flight simulations incorporate propeller performance to predict thrust, moments, and power consumption and propeller model accuracy is important in identifying safe operating regimes for this aircraft. Current high-lift propeller performance models have been verified and calibrated against numerous computational fluid dynamics analyses under a variety of flight conditions. We performed a series of full-scale wind tunnel tests at the NASA Langley Research Center Low Speed Aeroacoustic Wind Tunnel to further validate these models, to identify any adverse operating conditions for these propellers, and to assess the accuracy of the facility’s new Propeller Test Stand. The results indicate that the models accurately predicted performance and that the right-handed propeller showed lower torque and thrust for a given propeller speed compared to the left-handed version. Acoustic data support these measurements, showing higher tonal noise for the left versus right propeller. We suspect this is due to slight differences in the material properties between the early production (right) and more recent (left) blade sets leading to greater detwisting in the right-handed blades under load. Both propellers demonstrated very stable operation throughout the test including during deployment, stowing, and windmilling. Furthermore, high-speed imagery of the spinning propeller indicated no blade oscillations or instabilities for any test case. We also leveraged these images to analyze the effects of propeller loading on blade detwisting and tip position. Unfortunately, the thrust measurements varied significantly during the test due to cross-loading of the Propeller Test Stand load cell, though trends in the thrust data were still observable. The torque measurement, however, remained very precise for all test points and was used for performance comparisons. As a result of this test, we validated and improved the X-57 high-lift propeller performance models, obtained detailed propeller acoustic data and high-speed imagery, observed the propeller operating safely during a variety of dynamic events, and identified two potentially adverse, low-propeller-speed conditions which will be avoided during normal aircraft operation.

X-57↗

Modeling of Fillets in Thin-Walled Structures for Dynamic Analysis

Relatively new developments in manufacturing methods have made it possible to produce machined parts with a wall thickness of less than 0.010". While the parts are being machined. Fillets of relatively large radius to thickness ratios are created by the milling tool. This paper discusses an accurate new technique for finite-element modeling of fillets for dynamic and stiffness analysis using efficient plate elements rather than more computationally intensive, high density solid meshes, A simple filleted cantilever beam of 0.040" thickness, 1.6" length, 1" depth, and 0.250" radius in the corner was modeled using both solid elements and several different plate element geometries. The finite element results were then compared with static and modal testing of a machined sample. The highest-scoring plate element technique uses a bridge of elements that is constructed through the tangent point of the Fillet radius such that the thickness of the element matches tile volume of the fillet. This model produces errors of less than 4.6 percent for static loading and less than 7.4 percent for modal analysis. This simple plate element technique will prove critical for efficient, timely, and accurate dynamic analysis of complex thin-walled structures.

Seugling, Richard M.↗

Contact dynamics testing of automated three-point docking mechanism

An evaluation of an OMV docking mechanism, based on an adaptation of the Shuttle Flight Support System Pallet Berthing Mechanism was completed. The mechanism uses automatically actuated motorized latches to engage towel bars on the target satellite. LED sensors establish the towel bar position within the capture envelope and the latch capture commands are issued. Then, locking pawls engage the bar, locking and pre-loading the mechanism. Two series of tests were conducted to test nominal and failure mode captures and to evaluate design parameters such as LED sensor locations, automatic closure algorithms, latch closure velocity, position/velocity entry envelopes, and closure method. The first test series involved single latch testing on the Flat Floor Facility, the 6 DOF Facility, and an analytic simulation model. The intent was to compare results in order to validate the various facilities. Reasonably good agreement was achieved. The second test series repeated the single latch testing on the refurbished 6 DOF Facility to validate the facility modifications. The individual latches were tested under free-drift conditions for functionality and performance. Next, the three-latch configuration underwent parametric testing. Test results validated the improved fidelity of the 6 DOF Facility and verified successful docking at the required entry velocity. The tests determined the 'best' design parameter definitions and concluded that the locking pawls should not lock until all three latches completely close.

Rourke, Kenneth H.↗

A concurrent irradiation-mechanics multiscale coupling model

The vast majority of our current knowledge regarding the basic mechanisms controlling irradiation effect on mechanical properties is based almost entirely on the results of post-irradiation experiments or theoretical models. However, the concurrent effects of irradiation, mechanical stress, and thermal damage on the failure phenomena of materials and components remain largely unexplored due to its internal multiscale-multiphysics coupling nature. Here, we present here a concurrent irradiation-mechanics multiscale coupling model. The concurrent evolutions of nanoscale irradiation defect clusters, microscale dislocation configurations, and mechanical responses are well captured based on coupling cluster dynamics, discrete dislocation dynamics, and the finite element methods using an effective time marching scheme. Model predictions of defect densities and size are in general agreement with experimental observations. Irradiation hardening is shown to take place also in samples undergoing concurrent irradiation-mechanical loading, similar to samples tested post-irradiation. However, the occurrence of plastic flow localization and dislocation channel formation is not accompanied with apparent yield drop (softening) under concurrent irradiation-mechanical loading conditions, which is different from the post-irradiation case.

42 ENGINEERING↗

Processing and mechanical properties - 2016-0032

Hot extrusion is used within the forming route of cladding tubes to deform the billets into tube hollows, which are then cold-rolled to produce the final tubes with the suitable properties for in-reactor use. The hot extrusion goals are to give the appropriate geometry for cold pilgering (diameter and wall thickness suitable for cold-rolling mills, good concentricity) without surface defects and microstructural heterogeneities, which are detrimental for subsequent rolling. To ensure a good quality of the tube hollows, extrusion parameters (e.g., temperature of the billet, ram speed, extrusion ratio, lubrication) and extrusion tools have to be chosen as a function of the press capacity and mechanical and microstructural properties of the extruded alloy. For this purpose, finite-element and analytical models are used in addition to experimental tests. These models, particularly the former, can take into account the thermomechanical coupling that occurs in the tube and the tools during extrusion and provides a good prediction of the extrusion pressure and thermomechanical history of the extruded product. Together with a microstructural evolution model identified with small-scale extrusion tests, torsion tests, and heat treatments, this last result can also be used to calculate the fragmentation of the microstructure in the die and the meta-dynamic recrystallization after extrusion. Once validated against experimental data, numerical models were used to better understand and master the extrusion loads, the microstructure evolutions at the front end of the extruded tubes, and the temperature and stresses applied to the tools. (authors)

36 MATERIALS SCIENCE↗

ACT University Collaboration Proposal: Role of manufacturing defects on material failure under dynamic loading for developing enhanced failure models and theories (Final Report)

Research on the tensile behavior of additively manufactured 316L stainless steel coupon specimens at increasing strain rates was conducted over the past year at Penn State. Dynamic loading rates into the 1000 1/s loading rates were performed on specimens with nearly 1.32” gage lengths. Stress-strain plots show ductile and plastic behavior well beyond 12% strain with necked specimens, having smaller effective gage lengths showing up to 56% ultimate strain. Additional tests performed on compact tension specimens helped with simulation work to understand the deformation behavior. Using finite elements, it was possible to determine the feasibility of a comprehensive experimental validation study towards an improved model for AM material failure – specifically, the Bai-Wierzbicki approach which accounts for lode angle and triaxiality. A non-significant number of tests are projected for eight specific failure nodes, with additional replicates to provide strain-rate capabilities to the existing formulation. One such correction factor is explored for quasi-static, notched specimens. Finally, stress intensity factor was explored using a set of compact-tension specimens which would also provide useful validation data for any simulation work.

36 MATERIALS SCIENCE↗

Postflight simulation of parachute deployment dynamics of Viking qualification flight tests

Simulation calculations of the Viking qualification flight tests are conducted by use of analytical models of the parachute deployment dynamics process. Results from the study indicate that good simulations of event times and trajectory are obtained. If the full-scale parachute drag coefficient is used, a good simulation of first opening load is obtained and the overall nature of the load history is calculated. For longitudinal motions, the two-degree-of-freedom models give good agreement with a six-degree-of-freedom model. It is believed that the analytical models used are tools which will aid in the analysis of future flight systems.

Whitlock, C. H.↗

Dynamic Calibration of the NASA Ames Rotor Test Apparatus Steady/Dynamic Rotor Balance

The NASA Ames Rotor Test Apparatus was modified to include a Steady/Dynamic Rotor Balance. The dynamic calibration procedures and configurations are discussed. Random excitation was applied at the rotor hub, and vibratory force and moment responses were measured on the steady/dynamic rotor balance. Transfer functions were computed using the load cell data and the vibratory force and moment responses from the rotor balance. Calibration results showing the influence of frequency bandwidth, hub mass, rotor RPM, thrust preload, and dynamic loads through the stationary push rods are presented and discussed.

Peterson, Randall L.↗