Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

The role of pre-existing heterogeneities in materials under shock and spall

There has been a challenge for many decades to understand how heterogeneities influence the behavior of materials under shock loading, eventually leading to spall formation and failure. Experimental, analytical, and computational techniques have matured to the point where systematic studies of materials with complex microstructures under shock loading and the associated failure mechanisms are feasible. This is enabled by more accurate diagnostics as well as characterization methods. As interest in complex materials grows, understanding and predicting the role of heterogeneities in determining the dynamic behavior becomes crucial. Early computational studies, hydrocodes, in particular, historically preclude any irregularities in the form of defects and impurities in the material microstructure for the sake of simplification and to retain the hydrodynamic conservation equations. Contemporary computational methods, notably molecular dynamics simulations, can overcome this limitation by incorporating inhomogeneities albeit at a much lower length and time scale. This review discusses literature that has focused on investigating the role of various imperfections in the shock and spall behavior, emphasizing mainly heterogeneities such as second-phase particles, inclusions, and voids under both shock compression and release. Pre-existing defects are found in most engineering materials, ranging from thermodynamically necessary vacancies, to interstitial and dislocation, to microstructural features such as inclusions, second phase particles, voids, grain boundaries, and triple junctions. This literature review explores the interaction of these heterogeneities under shock loading during compression and release. Systematic characterization of material heterogeneities before and after shock loading, along with direct measurements of Hugoniot elastic limit and spall strength, allows for more generalized theories to be formulated. Further, continuous improvement toward time-resolved, in situ experimental data strengthens the ability to elucidate upon results gathered from simulations and analytical models, thus improving the overall ability to understand and predict how materials behave under dynamic loading.

36 MATERIALS SCIENCE↗

Phase Field Sintering Simulations of Tagged UO 2

Isotopic taggants are being considered as an additive for UO 2 manufacturing to improve nuclear security. Before taggants can be adopted, it must be determined whether taggants have any effect on the fuel microstructure or performance. As part of this effort, a grand potential formulation of the phase field method was used to model untagged, Cr-tagged, and Fe-tagged UO 2 . The simulations were compared to determine whether the taggants had any effect on fuel density or grain size. The results suggest that the taggants will not affect the density or grain size, but these findings may not be reliable because of high uncertainty. Causes of the uncertainty were discussed, and future work is proposed to reduce the model uncertainty.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Electrical and morphological characterization of transfer-printed Au/Ti/TiO{sub x}/p{sup +}-Si nano- and microstructures with plasma-grown titanium oxide layers

Highly-ordered, sub-70 nm-MOS-junctions of Au/Ti/TiO{sub x}/p{sup +}-Si were efficiently and reliably fabricated by nanotransfer-printing (nTP) over large areas and their functionality was investigated with respect to their application as MOS-devices. First, we used a temperature-enhanced nTP process and integrated the plasma-oxidation of a nm-thin titanium film being e-beam evaporated directly on the stamp before the printing step without affecting the p{sup +}-Si substrate. Second, morphological investigations (scanning electron microscopy) of the nanostructures confirm the reliable transfer of Au/Ti/TiO{sub x}-pillars of 50 nm, 75 nm, and 100 nm size of superior quality on p{sup +}-Si by our transfer protocol. Third, the fabricated nanodevices are also characterized electrically by conductive AFM. Fourth, the results are compared to probe station measurements on identically processed, i.e., transfer-printed μm-MOS-structures including a systematic investigation of the oxide formation. The jV-characteristics of these MOS-junctions demonstrate the electrical functionality as plasma-grown tunneling oxides and the effectivity of the transfer-printing process for their large-scale fabrication. Next, our findings are supported by fits to the jV-curves of the plasma-grown titanium oxide by kinetic-Monte-Carlo simulations. These fits allowed us to determine the dominant conduction mechanisms, the material parameters of the oxides and, in particular, a calibration of the thickness depending on applied plasma time and power. Finally, also a relative dielectric permittivity of 12 was found for such plasma-grown TiO{sub x}-layers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Manufacturing of SiCp Reinforced Magnesium Composite Tubes by Hot Extrusion Processes

Magnesium alloys have higher specific strength compared with other metals, such as aluminum, copper and steel. Nevertheless, their ductility is still not good for further metal forming and their strength is not large enough for real structure applications. The aim of this paper is to develop magnesium alloy composite tubes reinforced with SiC particulates by the stir-casting method and hot extrusion processes. At first, AZ61/SiCp composite ingots reinforced with 5 wt% SiC particulates are fabricated by the melt-stirring technique. Then, finite element simulations are conducted to analyze the plastic flow of magnesium alloy AZ61 within the die and the temperature distribution of the products. AZ61/SiCp composite tubes are manufactured by hot extrusion using a specially designed die-set for obtaining uniform thickness distribution tubes. Finally, the mechanical properties of the reinforced AZ61/SiCp composite and Mg alloy AZ61 tubes are compared with those of the billets to manifest the advantages of extrusion processes and reinforcement of SiC particulates. The microstructures of the billet and extruded tubes are also observed. Through the improvement of the strength of the tube product, its life cycle can be extended and the energy consumption can be reduced, and eventually the environmental sustainability is achieved.

36 MATERIALS SCIENCE↗

High-Temperature Deformation Behavior of Ti-6Al-2Sn-4Zr-2Mo Alloy with Lamellar Microstructure Under Plane-Strain Compression

High-temperature plane-strain compression of a Ti-6Al-2Sn-4Zr-2Mo (Ti-6242) alloy with a lamellar structure was applied by a thermal simulation machine Gleeble 3800 at a temperature of 1223-1370 K and a strain rate of 0.01-10 s{sup −1}. Constitutive relations between the flow stress and strain at different temperatures and strain rates were constructed based on the Arrhenius equation. Processing maps based on the dynamic material model at strains of 0.5, 1.0, and 1.25 were also constructed to analyze the mechanism and instability of high-temperature deformation. Dynamic recrystallization was found to occur at 1223-1313 K and 0.01-0.1 s{sup −1}, with a peak efficiency of power dissipation of 70%. Observations of the microstructure demonstrated that α platelets and dynamic globularization were responsible for dynamic softening in the α + β phase field. Flow instability behaviors occurred at 1263-1343 K/1.78-10 s{sup −1}, 1233-1283 K/0.1-3.16 s{sup −1}, and 1353-1373 K/0.56-1.78 s{sup −1}, and adiabatic shear bands and microcracks were observed in these domains. Thus, for the lamellar Ti-6242 alloy, the recommended hot rolling parameters were 1243-1333 K and 0.01-0.1 s{sup −1}. Electron backscattered diffraction results revealed that the dynamic restoration mechanism in the β phase field was dynamic recovery when the strain rate was as high as 10 s{sup −1}.

36 MATERIALS SCIENCE↗

Experimental observation of the interaction of propagating spin waves with Néel domain walls in a Landau domain structure

The interaction of propagating dipolar spin waves with magnetic domain walls is investigated in square-shaped microstructures patterned from the Heusler compound Co{sub 2}Mn{sub 0.6}Fe{sub 0.4}Si. Using magnetic force microscopy, the reversible preparation of a Landau state with four magnetic domains separated by Néel domain walls is confirmed. A local spin-wave excitation using a microstructured antenna is realized in one of the domains. It is shown by Brillouin light scattering microscopy that the domain structure in the remanence state has a strong influence on the spin-wave excitation and propagation. The domain walls strongly reflect the spin waves and can be used as spin-wave reflectors. A comparison with micromagnetic simulations shows that the strong reflection is due to the long-range dipolar interaction which has important implications for the use of these spin waves for exerting an all-magnonic spin-transfer torque.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Stress Relaxation Cracking of Alloys at Temperatures Higher Than 540°C

Type 347H stainless steel (347H SS), used in commercial concentrating solar power (CSP) thermal energy storage to store solar-salt at a temperature of 565°C, has been reported in the literature to be susceptible to stress-relaxation cracking (SRC). The welded heat-affected zone (HAZ) and fusion zone (FZ) of 347H SS, particularly in thick sections, are known to be susceptible to failure during post-weld heat treatment (reheat cracking). SRC could also occur after months or years under an elevated-temperature service environment. Two conditions must be present for failure to occur in the HAZ and/or FZ: 1) a modified or sensitized microstructure and 2) sufficiently high tensile residual stresses present at the elevated service temperature. The overarching goal of this project is to recommend SRC mitigation protocols to avoid susceptibility to fail through SRC at temperatures relevant for CSP. Post weld heat treatment conditions and alternative alloys are investigated as potential mitigation solutions to SRC. We used Gleeble thermomechanical simulation tests and finite element (FE) models to understand the susceptibility of 347H SS to SRC as a function of temperature, stress, and microstructure. We started with a literature review of weldability issues with 347H SS and techniques to mitigate SRC in 347H SS weldments. Next, we used Gleeble experiments to determine reheat cracking susceptibility in the simulated HAZ of 347SS weldments and an alternative alloy, 316L SS (NUCL 167 SPH) with boron added. We also performed Gleeble experiments to compare the reheat cracking susceptibility of 347H cross welded with two different fillers: E347, which is used in some commercial CSP TES tanks, and E16.8.2. We validated the experimental results with FE models of the residual stresses. We found that although the 316L (NUCL 167 SPH) is less susceptible to reheat cracking, it is slightly weaker than 347H and ASME BP&V codes limit its use to a service condition of 565°C. We also found that welds using E16.8.2 as the weld filler are less susceptible to failure than those using E347, likely due to the higher creep ductility of E16.8.2, and that it may be used as an alternative filler for repair welding of 347H welds or as the primary choice of filler for newly developed weld joints. We also found that post weld heat treatment could be a viable solution for mitigating stress in E347-347H SS thick, constrained welds, like those found in CSP tanks, and propose several options for mitigating SRC in existing and future TES tanks.

14 SOLAR ENERGY↗

Defect identification in simulated Bragg coherent diffraction imaging by automated AI

X-ray Bragg coherent diffraction imaging is a powerful technique for operando and in situ materials characterization and provides a unique means of quantifying the influence of one-dimensional (1D) and two-dimensional (2D) material defects on material response. However, obtaining full images from raw x-ray diffraction data is nontrivial and computationally intensive, precluding real-time experimental feedback. Here, we present a machine learning approach to identify the presence of crystalline line defects (edge and screw) in samples from the raw, 2D, coherent diffraction data without the need for image reconstruction through iterative phase retrieval. Further, we compare different approaches to designing neural networks for this application and demonstrate the potential of automated ML (autoML) approaches.

36 MATERIALS SCIENCE↗

Low-temperature swelling in LWR internal components: a computational assessment

A modern cluster dynamics model has been used to investigate the materials and irradiation parameters that control microstructural evolution under the relatively low-temperature exposure conditions that are representative of the operating environment for in-core light water reactor components. The focus is on components fabricated from austenitic stainless steel. The model accounts for the synergistic interaction between radiation-produced vacancies and the helium that is produced by nuclear transmutation reactions. Cavity nucleation rates are shown to be relatively high in this temperature regime (275 to 325 °C), but are sensitive to assumptions about the fine-scale microstructure produced under low-temperature irradiation. The cavity nucleation rates observed run counter to the expectation that void swelling would not occur under these conditions. This expectation was based on previous research on void swelling in austenitic steels in fast reactors. This misleading impression arose primarily from an absence of relevant data. The results of the computational modeling are generally consistent with recent data obtained by examining ex-service components. The long-term objective of this research is to provide a predictive model of void swelling at relevant lifetime exposures to support extended reactor operations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Numerical analysis of the influence of scale effects and microstructure on hydrogen diffusion in polycrystalline aggregates

Predicting resistance to environmental degradation, especially hydrogen embrittlement (HE) has become a major concern for life assessment and risk analysis of structural materials. The microstructure of the materials plays a significant role in HE. Despite the large documentation about the subject, the contribution of hydrogen diffusion on this process stays unclear. In this work, we analyze the effects of the microstructure on hydrogen diffusion, especially the influence of grain boundaries considered as high diffusivity paths and possible sites of damage occurrence. Electrochemical permeation was simulated using finite elements method (FEM). Scale effects between the RVE (Representative Volume Element) and the size of the membrane are discussed. Domains of applicability for standard homogenization methods, especially Hashin Shtrikman model are studied using results from microstructural based FEM. Domains of invariance of diffusion behavior and concentration profiles for grain shapes and the size of the membrane are also analyzed. Thus, the difficulty to extract diffusion properties by permeation test for heterogeneous microstructures is highlighted and discussed.

hydrogen, permeation, diffusion, microstructure, g↗

Computational Tools and Techniques for Modeling of Heterogeneous Materials

The specific goal of this CRADA was the development of computational tools and techniques for meso-to-macroscale modeling of transport processes to predict bulk properties of particulate and composite-based heterogeneous materials. These computational tools are particularly useful in exploring the relationship between a product's constituent materials, manufacturing process, resulting microstructure and bulk properties. The specific results of this project are: (i) advancements to the granular package and rigid body capability of the particle dynamics software, LAMMPS, for simulating fine cohesive particles and non-spherical granular particles; (ii) a software tool kit, documentation, and tutorials for statistical characterization, artificial reconstruction, and property-structure model analysis of material microstructure.

Lechman, Jeremy↗

Role of spall in microstructure evolution during laser-shock-driven rapid undercooling and resolidification

We previously reported [Colvin et al., J. Appl. Phys. 101, 084906 (2007)] on the microstructure morphology of pure Bi metal subjected to rapid laser-shock-driven melting and subsequent resolidification upon release of pressure, where the estimated effective undercooling rates were of the order of 10{sup 9}-10{sup 10} K/s. More recently, we repeated these experiments, but with a Bi/Zn alloy (Zn atomic fraction of 2%-4%) instead of elemental Bi and with a change in target design to suppress spall in the Bi/Zn samples. We observed a similar microstructure morphology in the two sets of experiments, with initially columnar grains recrystallizing to larger equiaxed grains. The Bi samples, however, exhibited micron-scale dendrites on the spall surfaces, whereas there were no dendritic structures anywhere in the nonspalled Bi/Zn, even down to the nanometer scale as observed by transmission electron microscopy. We present the simulations and the interferometry data that show that the samples in the two sets of experiments followed nearly identical hydrodynamic and thermodynamic paths apart from the presence of (probably partially liquid) spall in pure Bi. Simulations also show that the spall occurs right at the moving phase front and, hence, the spall itself cuts off the principal direction for latent heat dissipation across the phase boundary. We suggest that it is the liquid spall itself that creates the conditions for dendrite formation.

36 MATERIALS SCIENCE↗

A Phase-Field Model for the U-Pu-Zr System

Modeling nuclear materials is a multi-scale, multi-physics endeavor. Researchers are currently investigating how bulk material properties are affected by the evolution of microscopic material structures, i.e. microstructures. Development of tools that can mechanistically predict the effects of processes like diffusion and grain growth on properties like thermal conductivity will transform nuclear material design, manufacturing, and use. Intermediate-scale, i.e. mesoscale, modeling is among the most promising tools available for this task. Expedited development of mesoscale models, however, will require structured collaboration between modelers and experimentalists. Coupling these fields promises to improve both model accuracy and experiment design. With these ideas in mind, a mesoscale model of the U-Pu-Zr system is being developed. Its development will accompany a series of experiments involving irradiation of metallic fuel samples.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Linear Array Ultrasonic Test Results from Alkali-Silica Reaction (ASR) Specimens

The purpose of the U.S. Department of Energy Office of Nuclear Energy’s Light Water Reactor Sustainability (LWRS) Program is to develop technologies and other solutions that can improve the reliability, sustain the safety, and extend the operating lifetimes of nuclear power plants (NPPs) beyond 60 years. Since many important safety structures in an NPP are constructed of concrete, inspection techniques must be developed and tested to evaluate the internal condition. In-service containment structures generally do not allow for the destructive measures necessary to validate the accuracy of these inspection techniques. This creates a need for comparative testing of the various nondestructive evaluation (NDE) measurement techniques on concrete specimens with known material properties, voids, internal microstructure flaws, and reinforcement locations.This report presents results of the ultrasound evaluation of four concrete slabs with varying levels of ASR damage present. This included an investigation of the experimental results, as well as a supplemental simulation considering the effect of ASR damage by elasto-dynamic wave propagation using a finite integration technique method. It was found that the Hilbert Transform Indicator (HTI), developed for quantification of freeze/thaw damage in concrete structures, could also be successfully utilized for quantification of ASR damage. internal microstructure flaws, and reinforcement locations.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Integrating Experiments, Simulations, and Artificial Intelligence to Accelerate the Discovery of High-Performance Green Composites

The imperative for incorporating greener materials into the aerospace industry necessitates addressing significant challenges associated with the microstructural variability exhibited by recycled and sustainable feedstocks. In this study, we propose an integrated methodology that combines experimental investigations, finite element analysis, and artificial intelligence to develop sustainable composites with consistent properties. Our approach utilizes a pipeline comprising an automated mechanical tester, a finite element method simulator, and a convolutional neural network predictor to identify and optimize fabrication parameters for achieving desired mechanical characteristics in composites. By employing a nested-loop pipeline, our methodology improves sample efficiency, accuracy, and effectively bridges the gap between simulations and real-world performance. This unique methodology offers a promising avenue for facilitating the adoption of aerospace-appropriate green composites.

Athanasiou, Christos↗

Hybrid systems of AlInP microdisks and colloidal CdSe nanocrystals showing whispering-gallery modes at room temperature

We report on the realization of hybrid systems composed of passive optical microdisk resonators prepared from epitaxial layer systems and nanocrystal quantum emitters synthesized by colloidal chemistry. The AlInP disk material allows for the operation in the visible range, as probed by CdSe-based nanocrystals. Photoluminescence spectra at room temperature reveal sets of whispering-gallery modes consistent with finite-difference time-domain simulations. In the experiments, a special sample geometry renders it possible to detect resonant optical modes perpendicular to the disk plane.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Analysis of impact toughness scatter in simulated coarse-grained HAZ of E550 grade offshore engineering steel from the aspect of crystallographic structure

Highlights: • Crystallographic structure evolution in CGHAZ caused by variation of prior austenite grain size was analyzed quantitatively. • Variant selection rules changed from CP (close-packed plane) to Bain grouping with decreasing of prior austenite grain size. • A possible correlation between impact toughness scatter and crystallographic structure was established. - Abstract: This study aims at providing a new insights into the impact toughness scatter from the aspect of crystallographic structure. It demonstrated that the large impact toughness scatter associated much to the microstructure diversity. The crystallographic structure with evident scatter will display obvious discrepancy. In this work, three groups of samples simulated coarse-grained heat affected zone (CGHAZ) of an offshore engineering steel were obtained at different cooling rates. The Charpy test results showed that the toughness decreases dramatically with the decrease of cooling rate. However, the largest scatter in impact toughness occurred in the sample with medium cooling rate (15 °C/s), which was attributed to the heterogeneity in crystallographic structures. The visualization of crystallographic features showed that the prior austenite grain size has a significant effect on bainitic variant selection, which governed the effective grain size and crack propagation mechanism. CP (close-packed plane) grouping of variants is more likely to take place in large austenite grain, indicating that the size of CP region is larger than Bain zone, and the crack is short and flexural. On the contrary, in smaller austenite grain, Bain grouping of variants that always forms low angle grain boundary and favors crack propagation dominates the transformation, and it will promote the crack to propagate through the entire Bain zone and then yield large long crack. However, these two cases can co-exist in the same sample at medium cooling rate, indicating that the cleavage fracture is controlled by the effective grain size (Bain-zone size) and the scatter in impact toughness is associated much to the proportion and relative location between fine and coarse Bain zones.

36 MATERIALS SCIENCE↗

Individual phase constitutive properties of a TRIP-assisted QP980 steel from a combined synchrotron X-ray diffraction and crystal plasticity approach

Microstructure-based constitutive models for multiphase steels require accurate constitutive properties of the individual phases for component forming and performance simulations. We address this requirement with a combined experimental/theoretical methodology which determines the critical resolved shear stresses and hardening parameters of the constituent phases in QP980, a TRIP assisted steel subject to a two-step quenching and partitioning heat treatment. High energy X-Ray diffraction (HEXRD) from a synchrotron source provided the average lattice strains of the ferrite, martensite, and austenite phases from the measured volume during in situ tensile deformation. The HEXRD data was then input to a computationally efficient, elastic-plastic self-consistent (EPSC) crystal plasticity model which estimated the constitutive parameters of different slip systems for the three phases via a trial-and-error approach. The EPSC-estimated parameters are then input to a finite element crystal plasticity (CPFE) model representing the QP980 tensile sample. The predicted lattice strains and global stress versus strain curves are found to be 8% lower that the EPSC model predicted values and from the HEXRD measurements, respectively. This discrepancy, which is attributed to the stiff secant assumption in the EPSC formulation, is resolved with a second step in which CPFE is used to iteratively refine the EPSC-estimated parameters. Remarkably close agreement is obtained between the theoretically-predicted and experimentally derived flow curve for the QP980 material.

Hu, X. H. (ORCID:0000000277355091)↗