Search NASA⌕ Search

SEARCH · Search NASA

Results for “shape approximation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,207 records · Page 67

Performance Optimization of Plate Airfoils for Martian Rotor Applications Using a Genetic Algorithm

The Mars Helicopter Technology Demonstrator will be flying on the NASA Mars 2020 rover mission scheduled to launch in July of 2020. The goal is to demonstrate the viability and potential of heavier-than-air vehicles in the Martian atmosphere. Research is performed at the Jet Propulsion Laboratory and NASA Ames Research Center to extend these capabilities and develop the Mars Science Helicopter as the next possible step for Martian rotorcraft. The Mars Science Helicopter mass is scaled up to the 5 to 20 kg range, allowing a greater payload (approximately 0.5 to 2.0 kg), and greater range (approximately 3 km). Key to achieving these targets is careful aerodynamic rotor design. The Martian atmosphere’s low density and the small helicopter rotors result in very low chord-based Reynolds number flows, which reduces rotor performance. A continuous genetic algorithm is developed to optimize airfoil shapes at representative conditions for the Martian atmosphere. Previous research indicates that sharp leading edges and plate-like airfoils can out-perform conventional airfoil shapes. The present optimization allows for camber and thickness variation of curved and polygonal thin airfoils with sharp leading edges. The airfoil performance is evaluated at the highest attainable liftto- drag ratio near a moderate lift coefficient at compressible Mach numbers, as expected for Martian rotor application. Increases between 16% and 29% in airfoil lift-to-drag ratio at fixed lift coefficients are observed when compared with the Mars Helicopter Technology Demonstrator airfoils. Improvements in hover figure of merit are estimated to be between 4% and 10%, when applied to the Mars Helicopter Technology Demonstrator.

Koning, Witold J. F.↗

The diffuse X-ray background spectrum from 3 to 50 keV

The spectrum of the extragalactic diffuse X-ray background has been measured with the GSFC Cosmic X-ray Experiment on HEAO 1 for regions of the sky away from known point sources and more than 20 deg from the galactic plane. A total exposure of 80 sq m-s-sr is available at present. Free-free emission from an optically thin plasma of 40 plus or minus 5 keV provides an excellent description of the observed spectrum from 3 to 50 keV. This spectral shape is confirmed by measurements from five separate layers of three independent detectors. With an estimated absolute precision of about 10%, the intensity of the emission at 10keV is 3.2 keV/keV/sq cm/s/sr, a value consistent with the average of previously reported spectra. A uniform hot intergalactic medium of approximately 36% of the closure density of the universe would produce such a flux, although nonuniform models indicating less total matter are probably more realistic.

Marshall, F. E.↗

Numerical optimization design of advanced transonic wing configurations

A computationally efficient and versatile technique for use in the design of advanced transonic wing configurations has been developed. A reliable and fast transonic wing flow-field analysis program, TWING, has been coupled with a modified quasi-Newton method, unconstrained optimization algorithm, QNMDIF, to create a new design tool. Fully three-dimensional wing designs utilizing both specified wing pressure distributions and drag-to-lift ration minimization as design objectives are demonstrated. Because of the high computational efficiency of each of the components of the design code, in particular the vectorization of TWING and the high speed of the Cray X-MP vector computer, the computer time required for a typical wing design is reduced by approximately an order of magnitude over previous methods. In the results presented here, this computed wave drag has been used as the quantity to be optimized (minimized) with great success, yielding wing designs with nearly shock-free (zero wave drag) pressure distributions and very reasonable wing section shapes.

Cosentino, G. B.↗

Numerical optimization design of advanced transonic wing configurations

A computationally efficient and versatile technique for use in the design of advanced transonic wing configurations has been developed. A reliable and fast transonic wing flow-field analysis program, TWING, has been coupled with a modified quasi-Newton method, unconstrained optimization algorithm, QNMDIF, to create a new design tool. Fully three-dimensional wing designs utilizing both specified wing pressure disributions and drag-to-lift ratio minimization as design objectives are demonstrated. Because of the high computational efficiency of each of the components of the design code, in particular the vectorization of TWING and the high speed of the Cray X-MP vector computer, the computer time required for a typical wing design is reduced by approximately an order of magnitude over previous methods. In the results presented here, this computed wave drag has been used as the quantity to be optimized (minimized) with great success, yielding wing designs with nearly shock-free (zero wave drag) pressure distributions and very reasonable wing section shapes.

Cosentino, G. B.↗

A nonlinear analysis of an equilibrium craze. I - Problem formulation and solution. II - Simulations of craze and crack growth

A numerical method is developed for the determinations of the equilibrium shape of a craze in an infinite elastic plane whose fibrils exhibit very general nonlinear force-displacement behavior. The problem formulation is based on the superposition of the relevant elasticity Green's function; the solution of the resulting nonlinear problem is obtained by using Picard's successive approximation scheme. The model is used to investigate the effect of nonlinear fibril behavior on the mechanics of craze and crack growth, and the results are compared with the Dugdale model.

Ungsuwarungsri, T.↗

A contact stress model for multifingered grasps of rough objects

The model developed utilizes a contact-stress analysis of an arbitrarily shaped object in a multifingered grasp. The fingers and the object are all treated as elastic bodies, and the region of contact is modeled as a deformable surface patch. The relationship between the friction and normal forces is nonlocal and nonlinear in nature and departs from the Coulomb approximation. The nature of the constraints arising out of conditions for compatibility and static equilibrium motivated the formulation of the model as a nonlinear constrained minimization problem. The model is able to predict the magnitude of the inwardly directed normal forces and both the magnitude and direction of the tangential (friction) forces at each finger-object interface for grasped objects in static equilibrium.

Sinha, Pramath Raj↗

Intelligent automated surface grid generation

The goal of our research is to produce a flexible, general grid generator for automated use by other programs, such as numerical optimizers. The current trend in the gridding field is toward interactive gridding. Interactive gridding more readily taps into the spatial reasoning abilities of the human user through the use of a graphical interface with a mouse. However, a sometimes fruitful approach to generating new designs is to apply an optimizer with shape modification operators to improve an initial design. In order for this approach to be useful, the optimizer must be able to automatically grid and evaluate the candidate designs. This paper describes and intelligent gridder that is capable of analyzing the topology of the spatial domain and predicting approximate physical behaviors based on the geometry of the spatial domain to automatically generate grids for computational fluid dynamics simulators. Typically gridding programs are given a partitioning of the spatial domain to assist the gridder. Our gridder is capable of performing this partitioning. This enables the gridder to automatically grid spatial domains of wide range of configurations.

Yao, Ke-Thia↗

Galactic cosmic ray modulation and interplanetary medium perturbations due to a long-living active region during October 1989

During October 1989, three very energetic flares were ejected by the same active region at longitudes 9 deg E, 32 deg W, and 57 deg W, respectively. The shape of the galactic cosmic ray variations suggests the presence of large magnetic cloud structures (Nagashima et al., 1990) following the shock-associated perturbations. In spite of long data gaps the interplanetary observations at Interplanetary Monitoring Platform (IMP) 8 (near the Earth) and International Cometary Explorer (ICE)(approximately 1 AU, approximately 65 deg W) confirm this possibility for the event related to the 9 deg E flare; the principal axes analysis shows that the interplanetary magnetic field variations at both spacecraft locations are mainly confined on a meridian plane. This result suggests that the western longitudinal extension of this cloud is indeed very large (greater than or equal to 5 deg). The nonnegligible depression in the cosmic ray intensity observed inside the possible cloud related to the 57 deg W flare indicates that also the eastern extension could be very wide. The analysis of neutron monitor data shows clearly the cosmic ray trapping effect of magnetic clouds; this mechanism seems to be responsible for the enhanced diurnal effect often observed during the recovery phase of Forbush decreases. We give an interpretation for the anisotropic cosmic ray peak occurring in the third event, and, related to that, we suggest that the Forbush decrease modulated region at the Earth's orbit could be somewhat wider than the magnetic cloud, as already anticipated by Nagashima et al. (1990). By this analysis, based mainly on cosmic ray data, we show that it is possible to do reasonable inferences on the large-scale structure of flare-related interplanetary perturbations when interplanetary medium data are not completely present.

Bavassano, B.↗

SMEX-Lite Modular Solar Array Architecture

For the most part, Goddard solar arrays have been custom designs that are unique to each mission. The solar panel design has been frozen prior to issuing an RFP for their procurement. There has typically been 6-9 months between RFP release and contract award, followed by an additional 24 months for performance of the contract. For Small Explorer (SMEX) missions, with three years between mission definition and launch, this has been a significant problem. The SMEX solar panels have been sufficiently small that the contract performance period has been reduced to 12-15 months. The bulk of this time is used up in the final design definition and fabrication of flight solar cell assemblies. Even so, it has been virtually impossible to have the spacecraft design at a level of maturity sufficient to freeze the solar panel geometry and release the RFP in time to avoid schedule problems with integrating the solar panels to the spacecraft. With that in mind, the SMEX-Lite project team developed a modular architecture for the assembly of solar arrays to greatly reduce the cost and schedule associated with the development of a mission- specific solar array. In the modular architecture, solar cells are fabricated onto small substrate panels. This modular panel (approximately 8.5" x 17" in this case) becomes the building block for constructing solar arrays for multiple missions with varying power requirements and geometrical arrangements. The mechanical framework that holds these modules together as a solar array is the only mission-unique design, changing in size and shape as required for each mission. There are several advantages to this approach. First, the typical solar array development cycle requires a mission unique design, procurement, and qualification including a custom qualification panel. With the modular architecture, a single qualification of the SMEX-Lite modules and the associated mechanical framework in a typical configuration provided a qualification by similarity to multiple missions. It then becomes possible to procure solar array modules in advance of mission definition and respond quickly and inexpensively to a selected mission's unique requirements. The solar array modular architecture allows the procurement of solar array modules before the array geometry has been frozen. This reduces the effect of procurement lead-time on the mission integration and test flow by as much as 50%. Second, by spreading the non-recurring costs over multiple missions, the cost per unit area is also reduced. In the case of the SMEX-Lite procurement, this reduction was by about one third of the cost per unit area compared to previous SMEX mission-unique procurements. Third, the modular architecture greatly facilitates the infusion of new solar cell technologies into flight programs as these technologies become available. New solar cell technologies need only be fabricated onto a standard-sized module to be incorporated into the next available mission. The modular solar array can be flown in a mixed configuration with some new and some standard cell technologies. Since each module has its own wiring terminals, the array can be arranged as desired electrically with little impact to cost and schedule. The solar array modular architecture does impose some additional constraints on systems and subsystem engineers. First, they must work with discrete solar array modules rather than size the array to fit exactly within an available envelope. The array area is constrained to an integer multiple of the module area. Second, the modular design is optimized for space radiation and thermal environments not greatly different from a typical SMEX LEO environment. For example, a mission with a highly elliptical orbit (e.g., Polar, SMEX/FAST) would require thicker coverglasses to protect the solar cells from the more intense radiation environment.

Lyons, John↗

Evidence for a 115 Day Orbital Period in the Ultraluminous X-ray Source NGC 5408 X-1

We report the detection of a 115 day periodicity in SWIFT/XRT monitoring data from the ultraluminous X-ray source (ULX) NGC 5408 X-1. Our ongoing campaign samples its X-ray flux approximately twice weekly and has now achieved a temporal baseline of more than 500 days. Timing analysis reveals a significant periodicity with a period of 115.5 +- 4 days. The fractional modulation amplitude decreases with increasing energy, ranging from 0.13 above 1 keV to 0.24 below 1 keV. The shape of the profile evolves as well, becoming less sharply peaked at higher energies. Periodogram analysis is consistent with a periodic process, however, continued monitoring is required to confirm the coherent nature of the modulation. Spectral analysis indicates that NGC 5408 X-1 can reach 0.3 - 10 keV luminosities of 2 x 10e40 ergs/s. We suggest that, like the 62 day period of the ULX in M82 (X41.4+60), the periodicity detected in NGC 5408 X-1 represents the orbital period of the black hole binary containing the ULX. If this is true then the secondary can only be a giant or supergiant star.

Strohmayer, T.↗

L'CO/LFIR Relations with CO Rotational Ladders of Galaxies Across the Herschel SPIRE Archive

We present a catalog of all CO (carbon monoxide) (J (total angular momentum quantum number) equals 1-0 through J equals 13-12), [CI], and [NII] lines available from extragalactic spectra from the Herschel SPIRE (Spectral and Photometric Imaging Receiver) Fourier Transform Spectrometer (FTS) archive combined with observations of the low-J CO lines from the literature and from the Arizona Radio Observatory. This work examines the relationships between L (sub FIR (Far Infra Red)), L prime (sub CO), and L (sub CO) / L (sub CO, 1-0). We also present a new method for estimating probability distribution functions (PDFs) from marginal signal-to-noise ratio Herschel FTS spectra, which takes into account the instrumental "ringing" and the resulting highly correlated nature of the spectra. The slopes of Log (L (sub FIR)) versus Log (L prime (sub CO)) are linear for all mid- to high-J CO lines. The mid- to high-J CO luminosity relative to CO J equals 1-0 increases with increasing L (sub FIR), indicating higher excitement of the molecular gas, though these ratios do not exceed approximately 100. The luminosities relative to CO J equals 1-0 remain relatively at from J equals 6-5 through J equals13-2, across many orders of magnitude of L (sub FIR). Qualitative comparisons to current theoretical models do not match these flat SLED (spectral line energy distributions) shapes, indicating the need for more comprehensive modeling of the excitation processes of warm molecular gas in nearby galaxies.

Submillimeter Data↗

Optimal Mission Profile for Low-Boom Supersonic Aircraft

An optimal mission profile, called the low-boom mission profile, is proposed for low-boom supersonic aircraft. The low-boom mission profile uses a fixed AoA for the cruise segment until reaching the cruise ceiling. The fixed AoA is determined by the cruise condition for the low-boom shaping of the aircraft. The derived CL trajectory is not necessarily the optimal trajectory for the cruise range when unrestricted supersonic flight is allowed. The undertrack sonic boom ground noise level is reduced during the cruise because of the increasing altitude from the fixed AoA trajectory and the approximate invariance of nondimensional overpressure at 3BL below a supersonic aircraft with respect to cruise altitude change when the AoA and cruise Mach are fixed. The approximate invariance of nondimensional overpressure at 3BL below a supersonic aircraft is verified using both Euler and Reynolds-averaged Navier-Stokes CFD solvers. A low-boom supersonic transport concept is used to illustrate that, compared to the fixed cruise altitude trajectory, the low-boom mission profile can increase the cruise range of a low-boom aircraft and reduce the undertrack sonic boom ground noise levels for the entire cruise segment. One significant contribution of this paper is the implication that an aircraft OML satisfying a sonic boom ground noise level constraint at SOC will satisfy the same noise level constraint over the entire cruise segment, as long as a fixed AoA trajectory is flown.

Low-boom characteristics↗

Comparison of experimental and theoretical pressure-broadened atomic line shapes.

Line-structure calculations of the longer wavelength resonance line of cesium pressurized by argon are compared with experimental values over a range of perturber relative densities from 0.5 to 61. The main features of the line shapes are reproduced by the general pressures method using Lennard-Jones potentials. The calculations indicate that results are very sensitive to the potential parameters employed, but are not sensitive to changes in the temperature. The data are also compared with the method that makes the quasi-static approximation and with the high-pressure limit that leads to a Gaussian line profile. The former technique yields good agreement over the range of pressures where the approximation is warranted, and the latter appears to have several disadvantages.

Atakan, A. K.↗

Automatic N(h,t) profiles of the ionosphere with a digital ionosonde

A method is described to accomplish automatic data selection and profile inversion to obtain ionospheric electron density profiles from digitized radio soundings. The profile inversion is based on a well-established formulation by which the optimum radio frequency sounding intervals can be specified from an approximate knowledge of the profile; the expected virtual height coordinates (h) at these frequencies (f) are estimated, and procedures are then used to select h(f) observations nearest the predicted coordinates from a subsequent digital ionogram. From these the next profile is obtained. The process adaptively follows the changing shape and detail of the profile. The procedure requires an average of 15 sec per profile on a standard data processing computer, and can be adapted, with benefit to online real-time use in a digital ionosonde.

Wright, J. W.↗

Far-field multimodal acoustic radiation directivity

Approximate equations for the far field acoustic radiation patterns in the forward quadrant from a flanged circular duct were compared with exact equations for both single and multimodal excitations. The single mode comparison showed good agreement between the exact and approximate equations for the principal lobes of higher radial order modes. For lower and especially for zero radial order modes, there was some error in the angular location and decibel level of principal lobe peak pressure obtained from the approximate equation. Some agreement of sidelobes was also observed although the approximate equation was not intended to simulate the sidelobes. The multimodal approximate summation equations consisting only of a simple function of directivity angle and an acoustic power biasing function were checked against the exact equations for several distributions of modal power and showed excellent agreement with exact equations for all cases. Although many modes contribute to the final level and shape of the directivity curve, the major contributions appear to come from the higher radial order modes.

Saule, A. V.↗

Evacuated load-bearing high performance insulation study

A light weight, vacuum jacketed, load bearing cryogenic insulation system was developed and tested on a 1.17-m (46-in.) spherical test tank. The vacuum jacket consists of 0.08 mm (0.003 in.) thick 321 stainless steel formed into a wedge design that allows elastic jacket movements as the tank shrinks (cools) or expands (warms up or is pressurized). Hollow glass spheres, approximately 80 micrometers in diameter with a bulk density of 0.069 g/cc (4.3 lb cubic foot), provide the insulating qualities and one atmosphere load bearing capability required. The design, fabrication, and test effort developed the manufacturing methods and engineering data needed to scale the system to other tank sizes, shapes, and applications. The program demonstrated that thin wall jackets can be formed and welded to maintain the required vacuum level of .013 Pa yet flex elastically for multiple reuses. No significant shifting or breakage of the microspheres occurred after 13 simulated Space Tug flight cycles on the test tank and a hundred 1 atmosphere load cycles in a flat plate calorimeter. The test data were then scaled to the Space Tug LO2 and LH2 tanks, and weight, thermal performance, payload performance, and costs were compared with a helium purged multilayer insulation system.

Parmley, R. T.↗

The role of cesium suboxides in low-work-function surface layers studied by X-ray photoelectron spectroscopy - Ag-O-Cs

The oxidation of cesium on silver substrates has been studied using photoyield measurements and X-ray photoelectron spectroscopy. The occurrence of two O1s peaks in the core-level spectrum at 527.5 and 531.5-eV binding energy for cesium and oxygen exposures giving the optimum photoyield proves that two oxides of cesium exist in high-photoyield surfaces, and not Cs2O alone as previously thought. From the shape and position of the cesium peaks and the Auger parameter, the assignment of the O1s peaks at 527.5- and 531.5-eV binding energies to oxygen in Cs2O and Cs11O3, respectively, can be made. Hence the total cesium-oxygen layer is a mixed phase consisting of Cs2O + Cs11O3, approximately 20-40 A thick.

Yang, S.-J.↗

Sensitivity of C-Band Polarimetric Radar-Based Drop Size Distribution Measurements to Maximum Diameter Assumptions

The estimation of rain drop size distribution (DSD) parameters from polarimetric radar observations is accomplished by first establishing a relationship between differential reflectivity (Z(sub dr)) and the central tendency of the rain DSD such as the median volume diameter (D0). Since Z(sub dr) does not provide a direct measurement of DSD central tendency, the relationship is typically derived empirically from rain drop and radar scattering models (e.g., D0 = F[Z (sub dr)] ). Past studies have explored the general sensitivity of these models to temperature, radar wavelength, the drop shape vs. size relation, and DSD variability. Much progress has been made in recent years in measuring the drop shape and DSD variability using surface-based disdrometers, such as the 2D Video disdrometer (2DVD), and documenting their impact on polarimetric radar techniques. In addition to measuring drop shape, another advantage of the 2DVD over earlier impact type disdrometers is its ability to resolve drop diameters in excess of 5 mm. Despite this improvement, the sampling limitations of a disdrometer, including the 2DVD, make it very difficult to adequately measure the maximum drop diameter (D(sub max)) present in a typical radar resolution volume. As a result, D(sub max) must still be assumed in the drop and radar models from which D0 = F[Z(sub dr)] is derived. Since scattering resonance at C-band wavelengths begins to occur in drop diameters larger than about 5 mm, modeled C-band radar parameters, particularly Z(sub dr), can be sensitive to D(sub max) assumptions. In past C-band radar studies, a variety of D(sub max) assumptions have been made, including the actual disdrometer estimate of D(sub max) during a typical sampling period (e.g., 1-3 minutes), D(sub max) = C (where C is constant at values from 5 to 8 mm), and D(sub max) = M*D0 (where the constant multiple, M, is fixed at values ranging from 2.5 to 3.5). The overall objective of this NASA Global Precipitation Measurement Mission (GPM/PMM Science Team)-funded study is to document the sensitivity of DSD measurements, including estimates of D0, from C-band Z(sub dr) and reflectivity to this range of D(sub max) assumptions. For this study, GPM Ground Validation 2DVD's were operated under the scanning domain of the UAHuntsville ARMOR C-band dual-polarimetric radar. Approximately 7500 minutes of DSD data were collected and processed to create gamma size distribution parameters using a truncated method of moments approach. After creating the gamma parameter datasets the DSD's were then used as input to a T-matrix model for computation of polarimetric radar moments at C-band. All necessary model parameterizations, such as temperature, drop shape, and drop fall mode, were fixed at typically accepted values while the D(sub max) assumption was allowed to vary in sensitivity tests. By hypothesizing a DSD model with D(sub max) (fit) from which the empirical fit to D0 = F[Z(sub dr)] was derived via non-linear least squares regression and a separate reference DSD model with D(sub max) (truth), bias and standard error in D0 retrievals were estimated in the presence of Z(sub dr) measurement error and hypothesized mismatch in D(sub max) assumptions. Although the normalized standard error for D0 = F[Z(sub dr)r] can increase slightly (as much as from 11% to 16% for all 7500 DSDs) when the D(sub max) (fit) does not match D(sub max) (truth), the primary impact of uncertainty in D(sub max) is a potential increase in normalized bias error in D0 (from 0% to as much as 10% over all 7500 DSDs, depending on the extent of the mismatch between D(sub max) (fit) and D(sub max) (truth)). For DSDs characterized by large Z(sub dr) (Z(sub dr) > 1.5 to 2.0 dB), the normalized bias error for D0 estimation at C-band is sometimes unacceptably large (> 10%), again depending on the extent of the hypothesized D(sub max) mismatch. Modeled errors in D0 retrievals from Z(sub dr) at C-band are demonstrated in detail and comparedo similar modeled retrieval errors at S-band and X-band where the sensitivity to D(sub max) is expected to be less. The impact of D(sub max) assumptions to the retrieval of other DSD parameters such as Nw, the liquid water content normalized intercept parameter, are also explored. Likely implications for DSD retrievals using C-band polarimetric radar for GPM are assessed by considering current community knowledge regarding D(sub max) and quantifying the statistical distribution of Z(sub dr) from ARMOR over a large variety of meteorological conditions. Based on these results and the prevalence of C-band polarimetric radars worldwide, a call for more emphasis on constraining our observational estimate of D(sub max) within a typical radar resolution volume is made

Carey, Lawrence D.↗