Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composite Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 1,225 records · Page 68

Strong, Tough, and Pest Resistant MoSi2-Base Hybrid Composite for Structural Applications

Addition of about 30 to 50 vol % of Si3N4 particulate to MoSi2 improved resistance to low temperature accelerated oxidation by forming a Si2ON2 protective scale and thereby eliminating catastrophic 'pest failure'. The Si3N4 addition also improved the high temperature creep strength by nearly five orders of magnitude, doubled the room temperature toughness and significantly lowered the CTE of the MoSi2 and eliminated matrix cracking in SCS-6 reinforced composites even after thermal cycling. The SCS-6 fiber reinforcement improved the room temperature fracture toughness by seven times and impact resistance by five times. The composite exhibited excellent strength and toughness improvement up to 1400 C. More recently, tape casting was adopted as the preferred processing of MoSi2-base composites for improved fiber spacing, ability to use small diameter fibers, and for lower cost. Good strength and toughness values were also obtained with fine diameter Hi-Nicalon tow fibers. This hybrid composite remains competitive with ceramic matrix composites as a replacement for Ni-base superalloys in aircraft engine applications.

Hebsur, M. G.↗

Vertical distribution of structural components in corn stover

In the United States, corn ( Zea mays L.) stover has been targeted for second generation fuel production and other bio-products. Our objective was to characterize sugar and structural composition as a function of vertical distribution of corn stover (leaves and stalk) that was sampled at physiological maturity and about three weeks later from multiple USA locations. A small subset of samples was assessed for thermochemical composition. Concentrations of lignin, glucan, and xylan were about 10% greater at grain harvest than at physiological maturity, but harvestable biomass was about 25% less due to stalk breakage. Gross heating density above the ear averaged 16.3 ± 0.40 MJ kg⁻¹, but with an alkalinity measure of 0.83 g MJ⁻¹, slagging is likely to occur during gasification. Assuming a stover harvest height of 10 cm, the estimated ethanol yield would be >2500 L ha⁻¹, but it would be only 1000 L ha⁻¹ if stover harvest was restricted to the material from above the primary ear. Vertical composition of corn stover is relatively uniform; thus, decision on cutting height may be driven by agronomic, economic and environmental considerations.

09 BIOMASS FUELS↗

Study to investigate design, fabrication and test of low cost concepts for large hybrid composite helicopter fuselage, phase 2

The development of a frame/stringer/skin fabrication technique for composite airframe construction was studied as a low cost approach to the manufacturer of larger helicopter airframe components. A center cabin aluminum airframe section of the Sikorsky CH-53D, was selected for evaluation as a composite structure. The design, as developed, is composed of a woven KEVLAR R-49/epoxy skin and graphite/epoxy frames and stringers. The single cure concept is made possible by the utilization of pre-molded foam cores, over which the graphite/epoxy pre-impregnated frame and stringer reinforcements are positioned. Bolted composite channel sections were selected as the optimum joint construction. The applicability of the single cure concept to larger realistic curved airframe sections, and the durability of the composite structure in a realistic spectrum fatigue environment, was described.

Adams, K. M.↗

Sensitivity analysis for large-deflection and postbuckling responses on distributed-memory computers

A computational strategy is presented for calculating sensitivity coefficients for the nonlinear large-deflection and postbuckling responses of laminated composite structures on distributed-memory parallel computers. The strategy is applicable to any message-passing distributed computational environment. The key elements of the proposed strategy are: (1) a multiple-parameter reduced basis technique; (2) a parallel sparse equation solver based on a nested dissection (or multilevel substructuring) node ordering scheme; and (3) a multilevel parallel procedure for evaluating hierarchical sensitivity coefficients. The hierarchical sensitivity coefficients measure the sensitivity of the composite structure response to variations in three sets of interrelated parameters; namely, laminate, layer and micromechanical (fiber, matrix, and interface/interphase) parameters. The effectiveness of the strategy is assessed by performing hierarchical sensitivity analysis for the large-deflection and postbuckling responses of stiffened composite panels with cutouts on three distributed-memory computers. The panels are subjected to combined mechanical and thermal loads. The numerical studies presented demonstrate the advantages of the reduced basis technique for hierarchical sensitivity analysis on distributed-memory machines.

Watson, Brian C.↗

Tailoring Nanoporous Silica and Natural Straw Structural Insulation Composites

Nanoporous silica exhibits ultralow thermal conductivity as a result of its nanoscale pore size, high pore volume, and specific surface area. In this study, we report the self-assembled surfactant-templated synthesis of nanoporous silica, which is integrated with cellulose fibers derived from natural straw to manufacture high thermal insulation and mechanically robust nanocomposites. The nanocomposite shows a low thermal conductivity of 22.5 mW/(m·K), a compressive modulus of 0.93 MPa, and a hydrophobicity with a water contact angle of 125°. Moreover, we observed a marked reduction in water absorption capacity and a carbon footprint of 0.21 kg CO 2 equiv/kg. Here, this study provides a pathway toward the development of nanoporous structural insulation materials for energy-efficient building applications.

36 MATERIALS SCIENCE↗

Structure and composition of higher-rhenium-content superalloy based on La-alloyed Ni-Al-Cr

The paper presents the transmission and scanning electronic microscope investigations of Ni-Al-Cr superalloy alloyed with additional Re and La elements. This superalloy is obtained by a directional solidification method. It is shown that such additional elements as Re and La result in formation of new phases in Ni-Al-Cr accompanied by considerable modifications of quasi-cuboid structure in its γ’-phase.

36 MATERIALS SCIENCE↗

Processing, properties and applications of composites using powder-coated epoxy towpreg technology

Composite manufacturing using the current prepregging technology of impregnating liquid resin into three-dimensionally reinforced textile preforms can be a costly and difficult operation. Alternatively, using polymer in the solid form, grinding it into a powder, and then depositing it onto a carbon fiber tow prior to making a textile preform is a viable method for the production of complex textile shapes. The powder-coated towpreg yarn is stable, needs no refrigeration, contains no solvents and is easy to process into various woven and braided preforms for later consolidation into composite structures. NASA's Advanced Composites Technology (ACT) program has provided an avenue for developing the technology by which advanced resins and their powder-coated preforms may be used in aircraft structures. Two-dimensional braiding and weaving studies using powder-coated towpreg have been conducted to determine the effect of resin content, towpreg size and twist on textile composite properties. Studies have been made to customize the towpreg to reduce friction and bulk factor. Processing parameters have been determined for three epoxy resin systems on eight-harness satin fabric, and on more advanced 3-D preform architectures for the downselected resin system. Processing effects and the resultant mechanical properties of these textile composites will be presented and compared.

Bayha, T. D.↗

Conductive overbraid of continuous fiber thermoplastic composite tows

Here, to meet the increasing demand for lightweight materials with multifunctional capabilities, a new high-rate manufacturing method and material system, referred to as M-TOW ® (multifunctional-tow) is introduced. Overbraiding is used to incorporate highly conductive wire onto the continuous fiber reinforced tow (M-TOW ® ), offering a solution for integrating thermal and electrical conductivity into hybrid-molded composite structures. The conductivity performance of different wire configurations are compared before and after forming the M TOW ® , measuring electrical conductivities up to 5.5 x 10 5 S / cm and thermal conductivities up to 21 W / mK. Results conclude that the integration of conductive wires into thermoplastic preforms is a viable means of expanding the functionality of lightweight, high strength composite structures.

3-dimensional reinforcement↗

Enhancement of Fluorescence and Raman Scattering in Cyanine-Dye Molecules on the Surface of Silicon-Coated Silver Nanoparticles

A method of formation of a composite structure based on silver nanoparticles and a thin protective silicon film (AgNPs/Si) is developed. Enhancement of the fluorescence and Raman scattering in cyaninedye molecules deposited onto the formed nanostructure is observed. The optical properties and morphology stability of particles that are in contact with cyanine-dye solutions in organic solvents are studied. It is shown that the AgNPs/Si composite structure can be multiply used as an SERS-active surface.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Characterization and photoluminescence of Co-doped SiC films

Co-doped SiC films are fabricated on Si (100) substrates by radio frequency magnetron sputtering, and the crystal structure, composition, element valences, local structure, and photoluminescence of the films are studied. Crystal structure analysis identifies the film structure as 3C-SiC and shows that the Co dopant atoms form CoSi secondary phase compounds in the films. The composition and element valence analysis show that the Co dopant atoms substituting for C sites in the SiC lattice exist in the form of Co{sup 2+} ions, and that C clusters are present in the films, which increase in amount with increasing Co dopant concentration. The analysis of local structure reveals that Co clusters, CoO and Co{sub 3}O{sub 4}, are not present in the films, and CoSi secondary phase compounds exist. All of the films show a violet photoluminescence peak located at 413 nm, which becomes stronger with increased Co dopant concentration and annealing temperature, and is found to originate from the C clusters.

36 MATERIALS SCIENCE↗

Neutron irradiation and high temperature effects on amorphous Fe-based nano-coatings on steel – A macroscopic assessment

Here, this study revealed that loss of ductility in an amorphous Fe-alloy coating on a steel substrate composite structure was essentially prevented from occurring, following radiation with modest neutron doses of ~2 x 10 18 n/cm 2 . At the higher neutron dose of ~2 x 10 19 , macroscopic stress-strain analysis showed that the amorphous Fe-alloy nanostructured coating, while still amorphous, experienced radiation-induced embrittlement, no longer offering protection against ductility loss in the coating-substrate composite structure. Neutron irradiation in a corrosive environment revealed exemplary oxidation/corrosion resistance of the amorphous Fe-alloy coating, which is attributed to the formation of the Fe 2 B phase in the coating. To establish the impact of elevated temperatures on the amorphous-to-crystalline transition in the amorphous Fe-alloy, electron microscopy was carried out which confirmed the radiation-induced suppression of crystallization in the amorphous Fe-alloy nanostructured coating.

36 MATERIALS SCIENCE↗

The drive for Aircraft Energy Efficiency

NASA's Aircraft Energy Efficiency (ACEE) program, which began in 1976, has mounted a development effort in four major transport aircraft technology fields: laminar flow systems, advanced aerodynamics, flight controls, and composite structures. ACEE has explored two basic methods for achieving drag-reducing boundary layer laminarization: the use of suction through the wing structure (via slots or perforations) to remove boundary layer turbulence, and the encouragement of natural laminar flow maintenance through refined design practices. Wind tunnel tests have been conducted for wide bodied aircraft equipped with high aspect ratio supercritical wings and winglets. Maneuver load control and pitch-active stability augmentation control systems reduce fuel consumption by reducing the drag associated with high aircraft stability margins. Composite structures yield lighter airframes that in turn call for smaller wing and empennage areas, reducing induced drag for a given payload. In combination, all four areas of development are expected to yield a fuel consumption reduction of 40 percent.

James, R. L., Jr.↗

DNA extraction protocols cause differences in 16S rRNA amplicon sequencing efficiency but not in community profile composition or structure

The recent development of methods applying next-generation sequencing to microbial community characterization has led to the proliferation of these studies in a wide variety of sample types. Yet, variation in the physical properties of environmental samples demands that optimal DNA extraction techniques be explored for each new environment. The microbiota associated with many species of insects offer an extraction challenge as they are frequently surrounded by an armored exoskeleton, inhibiting disruption of the tissues within. In this study, we examine the efficacy of several commonly used protocols for extracting bacterial DNA from ants. While bacterial community composition recovered using Illumina 16S rRNA amplicon sequencing was not detectably biased by any method, the quantity of bacterial DNA varied drastically, reducing the number of samples that could be amplified and sequenced. These results indicate that the concentration necessary for dependable sequencing is around 10,000 copies of target DNA per microliter. Exoskeletal pulverization and tissue digestion increased the reliability of extractions, suggesting that these steps should be included in any study of insect-associated microorganisms that relies on obtaining microbial DNA from intact body segments. Although laboratory and analysis techniques should be standardized across diverse sample types as much as possible, minimal modifications such as these will increase the number of environments in which bacterial communities can be successfully studied.

16S rRNA↗

Composition-dependent structural and Raman spectroscopic studies on Y{sub 1-x}Ho{sub x}CrO{sub 3} (0≤x≤0.1)

In this paper we report the synthesis and structural characterization of polycrystalline holmium doped YCrO{sub 3} samples prepared by solid state reaction method. X-ray diffraction studies confirm the formation of single phase pure materials. Increasing Holmium substitution in Y{sub 1-x}Ho{sub x}CrO{sub 3} (0≤x≤0.1) allows a quasi-continuous tuning of the lattice in this multiferroic chromite without any magnetic interference effects of rare-earth ions. The composition dependent Raman scattering studies at room temperature reveal decreasing Raman mode frequencies with increasing holmium content consistent with the X-ray data. Decreasing phonon frequency shifts with increasing holmium content occurs, depending on the average rare-earth ion radius determined by the concentration of Y{sup +3} and Ho{sup +3}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Factors influencing the ultrasonic stress wave factor evaluation of composite material structures

To demonstrate that the finite-element model can be used to investigate some of the factors influencing the ultrasonic stress wave evaluation of materials, a hypothetical case was studied in which classical vibration theory was used. Vibration analysis and experiments for the undamaged case were conducted on an isotropic aluminum plate and a unidirectional graphite-epoxy plate, using a point source to excite the plates. The finite-element solution correlated within eight percent with the exact method. The frequencies predicted by the finite-element model were observed in the experiments in both plates, although in the composite plate, additional frequencies were observed which could not be accounted for. Damaged isotropic plates were also considered. The effects of increasing damage severity with constant damage area, and increasing damage area with constant severity on the resonant frequencies were analyzed.

Rebello, C. J.↗

Composition and Structure of Block-Type Ferrospheres Isolated from Calcium-Rich Power Plant Ash

Polished sections of individual ferrospheres 30 to 40 μm in size, with single-block and blocky structures and a variable glass phase content, have been studied using a scanning electron microscope equipped with an energy dispersive X-ray spectrometer system. The results demonstrate that the single-block globules consist of sintered magnetite crystallites containing Al{sub 2}O{sub 3}, MgO, and CaO as impurities and are formed from the pyrite of the initial coal. Characteristically, the ferrospheres with a variable glass phase content differ in the composition of local areas on polished sections of the globules, which attests to inhomogeneity of the melt droplets they formed from. We have identified groups of globules whose overall composition, as well as the composition of their local areas, meet general equations for the interrelation between the concentrations of their components: SiO{sub 2} = f(FeO) and SiO{sub 2} = f(Al{sub 2}O{sub 3}). Comparison of the coefficients of the SiO{sub 2} = f(Al{sub 2}O{sub 3}) dependence for the globules with the silicate modulus (SiO{sub 2}/Al{sub 2}O{sub 3}) of the aluminosilicate mineral components of the coal indicates that the formation of this type of globules involves pyrite–anorthite or pyrite–albite associates containing quartz impurities. The composition of the spinel ferrite in the globules produced with the participation of anorthite comprises FeO, Al{sub 2}O{sub 3}, MgO, and CaO in concentrations of 85–96, 1.7–10, 0.1–1.8, and 0.3–2.8 wt %, respectively. In the albite-based globules, the respective concentrations are 81–92, 0.7–5.9, 1.0–5.7, and 2.2–5.6 wt %. The crystallite size and shape are determined by the size of the local melt areas where the total concentration of spinel-forming oxides exceeds 85 wt %.

36 MATERIALS SCIENCE↗

Fundamental limits in heat-assisted magnetic recording and methods to overcome it with exchange spring structures

The switching probability of magnetic elements for heat-assisted recording with pulsed laser heating was investigated. It was found that FePt elements with a diameter of 5 nm and a height of 10 nm show, at a field of 0.5 T, thermally written-in errors of 12%, which is significantly too large for bit-patterned magnetic recording. Thermally written-in errors can be decreased if larger-head fields are applied. However, larger fields lead to an increase in the fundamental thermal jitter. This leads to a dilemma between thermally written-in errors and fundamental thermal jitter. This dilemma can be partly relaxed by increasing the thickness of the FePt film up to 30 nm. For realistic head fields, it is found that the fundamental thermal jitter is in the same order of magnitude of the fundamental thermal jitter in conventional recording, which is about 0.5–0.8 nm. Composite structures consisting of high Curie top layer and FePt as a hard magnetic storage layer can reduce the thermally written-in errors to be smaller than 10{sup −4} if the damping constant is increased in the soft layer. Large damping may be realized by doping with rare earth elements. Similar to single FePt grains in composite structure, an increase of switching probability is sacrificed by an increase of thermal jitter. Structures utilizing first-order phase transitions breaking the thermal jitter and writability dilemma are discussed.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗